TK-2202 TK-3202-1 TK-3202-2 IC:282D-36913210 IC:282D-36923210 FCC ID:ALH36913210 FCC ID:ALH36923210 FCC ID:ALH36923220 INSTRUCTION MANUAL TK-2202/TK-3202-1/TK-3202-2 THANK YOU!
We are grateful you chose KENWOOD for your land mobile radio applications. We believe this easy-to-use transceiver will provide dependable communications to keep personnel operating at peak efficiency. KENWOOD transceivers incorporate the latest in advanced technology. As a result, we feel strongly that you will be pleased with the quality and features of this product. NOTICES TO THE USER WARNING:
** GOVERNMENT LAW PROHIBITS THE OPERATION OF UNLICENSED RADIO TRANSMITTERS WITHIN THE TERRITORIES UNDER GOVERNMENT CONTROL.
**I LLEGAL OPERATION IS PUNISHABLE BY FINE OR IMPRISONMENT OR BOTH.
** REFER SERVICE TO QUALIFIED TECHNICIANS ONLY.
** DO NOT OPERATE YOUR TRANSCEIVER IN EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, ETC.).
** TURN OFF YOUR TRANSCEIVER WHILE TAKING ON FUEL, OR WHILE PARKED IN GASOLINE SERVICE STATIONS. SAFETY:
It is important that the operator is aware of and understands hazards common to the operation of any transceiver. WARNING:
EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, etc.) Turn off your transceiver while taking on fuel, or while parked in gasoline service stations. One or more of the following statements may be applicable:
FCC WARNING This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer for technical assistance. TK-2202 TK-3202-1 TK-3202-2 FCC ID:ALH36913210 FCC ID:ALH36923210 FCC ID:ALH36923220 IC:282D-36913210 IC:282D-36923210 ATTENTION (U.S.A. Only):
The RBRC Recycle seal found on KENWOOD nickel-metal hydride (Ni-MH) battery packs indicates KENWOOD s voluntary participation in an industry program to collect and recycle Ni-MH batteries after their operating life has expired. The RBRC program is an alternative to disposing Ni-MH batteries with your regular refuse or in municipal waste streams, which is illegal in some areas. For information on Ni-MH battery recycling in your area, call (toll free) 1-800-8-BATTERY
(1-800-822-8837). KENWOOD s involvement in this program is part of our commitment to preserve our environment and conserve our natural resources. UNPACKING AND CHECKING EQUIPMENT Note:
The following unpacking instructions are for use by your KENWOOD dealer, an authorized KENWOOD service facility, or the factory. Carefully unpack the transceiver. We recommend that you identify the items listed in the following table before discarding the packing material. If any items are missing or have been damaged during shipment, file a claim with the carrier immediately.
** Accessories Item Instruction Manual Belt Hook Screw Set Cap Holder Helical Antenna Whip Antenna Whip Antenna Battery Assy. Charger AC Adapter Pamphlet Part Number B62 1762 - *0 J29 0712 - 08 N99-2043-05 B09 0680 - *3 J19 5472 - *3 T90 1036 - *5 T90 1039- *5 T90 1040- *5 W09 1000- *5 W08 0969- *5 W08 0970- *5 B59 2371- *0 Quantity TK-2202 TK-3202-1 TK-3202-2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 TK-2202 TK-3202-1 TK-3202-2 IC:282D-36913210 IC:282D-36923210 FCC ID:ALH36913210 FCC ID:ALH36923210 FCC ID:ALH36923220 Installing/ Removing the Optional Battery Pack PREPARATION The battery pack is not charged at the factory; charge it before use. CAUTION:
** DO NOT RECHARGE THE BATTERY PACK IF IT IS ALREADY FULLY CHARGED. DOING SO MAY CAUSE THE LIFE OF THE BATTERY PACK TO SHORTEN OR THE BATTERY PACK MAY BE DAMAGED.
** AFTER RECHARGING THE BATTERY PACK, DISCONNECT IT FROM THE CHARGER. IF THE CHARGER POWER IS RESET (TURNED ON AFTER BEING TURNED OFF), RECHARGING WILL START AGAIN AND THE BATTERY PACK WILL BECOME OVERCHARGED.
** DO NOT SHORT THE BATTERY TERMINALS OR DISPOSE OF THE BATTERY BY FIRE.
** NEVER ATTEMPT TO REMOVE THE CASING FROM THE BATTERY PACK. 1 Match the guides of the battery pack with the corresponding grooves on the upper rear of the transceiver, then firmly press the battery pack t 2 To remove the battery pack, lift the safety catch, press the release latch, then pull the battery pack away from the transceiver. Installing the Antenna Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure. FCC ID:ALH36913210 FCC ID:ALH36923210 FCC ID:ALH36923220 TK-2202 TK-3202-1 TK-3202-2 IC:282D-36913210 IC:282D-36923210 Installing the Belt Clip Using the 2 screws, affix the belt clip in place. TK-2202 TK-3202-1 TK-3202-2 FCC ID:ALH36913210 FCC ID:ALH36923210 FCC ID:ALH36923220 Installing the Cap over the Speaker/Microphone Jacks If you are not using an optional speaker/ microphone, install the cap over the SP/MIC jacks using the supplied screw. Note:
To keep the transceiver water resistant, you must cover the SP/MIC jacks with the cap or the cap or the speaker/microphone connector. IC:282D-36913210 IC:282D-36923210 Installing the Optional Speaker/ Microphone 1 Insert the speaker/ microphone plugs into the SP/MIC jacks. 2 Install the speaker/microphone locking Holder over the plugs using the supplied screw. GETTING ACQUAINTED Knob TK-2202 TK-3202-1 TK-3202-2 FCC ID:ALH36913210 FCC ID:ALH36923210 FCC ID:ALH36923220 IC:282D-36913210 IC:282D-36923210 Lock/
Non Lock Lock/
Non Lock Description Power SW (CCW:Power OFF) Audio Volume adjuster Lock Channel Selector NO. Name 1 2 Power switch/
Volume control Selector switch PTT PF1 PF2 Switch Fig. 1 Left Side Fig.2 Front
<Left side>
NO. Name 1 2 3 PTT Side 1 Side 2 Selectable knob Volume Description Lock/
Non Lock Non Lock TX ON/OFF Non Lock Programmable default:No Function Non Lock Programmable default:Monitor Momentary NO. Name Description 1 LED The LED is three colors. Lights green while receiving at user mode.Lights red while transmitting,flashes red when the battery power is low while transmitting.Lights orange when individual called. LED TERMINAL SP/MIC jacks SP/MIC covering for blindfold mode of resin is possible. TK-2202 TK-3202-1 TK-3202-2 FCC ID:ALH36913210 FCC ID:ALH36923210 FCC ID:ALH36923220 IC:282D-36913210 IC:282D-36923210 NO. Name Description
I/O I I I O
O
O
PTT/RXD 1 2 MIC 3 MIC IN 4 5 6 7 8 9 10 OPTDET 5MS AE TXD NC SPO SPI PTT input / Serial data input MIC input To internal MIC Option Detect 5V output Audio Earth Serial data output No Connect AF power output To internal SP It s type of spring plate. The minus terminal connect to chassis ground It s mounted to rear side of radio and mounting instruction is slide method. Battery Terminal OTHER Rear Bottom A rail and a hook for battery installation. Space which affixes name plate.Model name plate Screw holes for belt hook installation. Battery release lever TK-2202 TK-3202-1 TK-3202-2 FCC ID:ALH36913210 FCC ID:ALH36923210 FCC ID:ALH36923220 IC:282D-36913210 IC:282D-36923210 Appearance TK-2202 TK-3202-1 TK-3202-2 IC:282D-36913210 IC:282D-36923210 FCC ID:ALH36913210 FCC ID:ALH36923210 FCC ID:ALH36923220 OPERATING BASICSATING BASICS
** Switching Power ON/OFF Turn the Power switch/ Volume control clockwise to switch the transceiver ON. Turn the Power switch/ Volume control counterclockwise to switch the transceiver OFF.
** Adjusting the Volume Rotate the Power switch/ Volume control to adjust the volume.
** Selecting a Channel Rotate the Channel selector to select a channel. Clockwise increases the channel number and counterclockwise decreases it.
** Making a Call 1 Select the desired channel. 2 Press and hold the PTT switch, then speak into the microphone in your normal voice. 3 For best results, hold the microphone approximately 3 to 4 cm (1 1/2 inches) from your lips. 4 Release the PTT switch to receive. AUXILIARY FEATURES
** Time-out Timer (TOT) The TOT is used to automatically inhibit transmission after a specified time elapse. If the PTT switch is held down for longer than specified time, the transceiver will stop transmitting and a tone will sound. Release the PTT switch, then press it again to continue transmitting.