all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User Manual | Users Manual | 724.91 KiB | ||||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | External Photos | |||||||
1 | Internal Photos | |||||||
1 | ID Label/Location Info | |||||||
1 | RF Exposure Info | |||||||
1 | RF Exposure Info | |||||||
1 | RF Exposure Info | |||||||
1 | RF Exposure Info | |||||||
1 | RF Exposure Info | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos |
1 | User Manual | Users Manual | 724.91 KiB |
INSTRUCTIoN MANUAl UHF FM TRANSCEIVER TK-3230 B62-1976-00 (K) 09 08 07 06 05 04 03 02 01 00 Thank You We are grateful for your purchase of this Kenwood product and welcome you to the Business Radio Service (BRS). Your Kenwood 2-way Business Radio is called a transceiver, meaning transmitter & receiver. We believe this easy-to-use transceiver will provide you with dependable and reliable communications. This Kenwood transceiver is a precision device. Treat it with care, and you will enjoy years of reliable operation. FeaTures Lightweight and compact design using a lithium-ion battery pack, with a sturdy, polycarbonate body and a spring-loaded belt clip. 122 tone/code settings for each channel, allowing you to ignore unwanted calls. Privacy Talk scrambles all your voice messages, giving you complete privacy for your conversations. FleetSync operation, allowing a variety of call types. Automatic battery power saver, providing you with longer battery usage. Battery power level indicator with low battery power warning. Key lock and Super Lock prevent you from accidentally changing your transceiver settings. Ten different calling alert tones allows you to identify yourself to your group before you begin speaking. Hands free operation when using an optional headset. operaTing CondiTions Open locations (no obstructions) Residential areas (near buildings) In steel/ concrete reinforced buildings Up to 200,000 ft2 (18,580 m2) In high rises Up to 4 miles (6.4 km) Up to 1.5 miles (2.4 km) Up to 15 floors Note: The listed ranges are based on field testing and may vary with your operating conditions. FCC LiCense inFormation Your Kenwood radio operates on communications frequencies which are subject to FCC (Federal Communications Commission) Rules & Regulations. FCC Rules require that all operators using Private Land Mobile radio frequencies obtain a radio license before operating their equipment. Application for license must be made on FCC form 601. FAX: Forms can be obtained by fax from the FCC Fax-On-Demand system. Call 1-202-418-0177 from your fax machine to request the documents. MAIL: Forms can be ordered by telephone, and will be sent to you by first class mail. Call the FCC Forms Hotline at 1-800-418-FORM (1-800-418-3676). INTERNET: Form 601 and instructions can be downloaded from the FCC Forms website at:
http://www.fcc.gov/formpage.html Before filling out your Form 601 application Technical Data section, you must decide which frequency (or frequencies) you will operate on. Refer to the frequency chart on page 44. Questons? Call the FCC for license application questions at 1-888-CALL-FCC (1-888-225-5322). ChanneL spaCing The ProTalkxls uses 12.5 kHz channel spacing, as per the regulations of the FCC. Transceivers using 12.5 kHz channel spacing may not have optimal sound quality when used with transceivers using 25 kHz channel spacing.
notiCes to the User This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. One or more of the following statements may be applicable:
FCC WARNING This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment to an outlet on a circuit different from that to Increase the separation between the equipment and receiver. which the receiver is connected. Consult the dealer for technical assistance.
SAFETY INFORMATION:
Your wireless hand-held portable transceiver has been designed using a low power transmitter. When the PTT switch is pressed, the transceiver generates radio frequency (RF) electromagnetic energy (EME). This transceiver is designed to comply with the FCC Report and Order FCC 96-326 (August, 1996). Do not transmit for more than 50% of the total operating time. Transmitting for over 50% of the operating time may exceed the FCC RF exposure compliance requirements. Transmission occurs while you are pressing the PTT switch and is confirmed by the LED that lights red while transmitting. To transmit, speak into the microphone in your normal voice while holding the transceiver upright and keep the antenna at least 2 inches (5 cm) from your head and body. When using a headset, ensure that the antenna is at least 2 inches (5 cm) away from your body whenever you are transmitting. Use only Kenwood genuine accessories. Unauthorized modifications, or attachments may damage the transceiver and violate FCC rules and regulations. ATTENTION (U.S.A. Only):
The RBRC Recycle seal found on Kenwood lithium-ion (Li-ion) battery packs indicates Kenwoods voluntary participation in an industry program to collect and recycle Li-ion batteries after their operating life has expired. The RBRC program is an alternative to disposing Li-ion batteries with your regular refuse or in municipal waste streams, which is illegal in some areas. For information on Li-ion battery recycling in your area, call (toll free) 1-800-8-BATTERY (1-800-822-8837). Kenwoods involvement in this program is part of our commitment to preserve our environment and conserve our natural resources.
Government law prohibits the operation of unlicensed radio transmitters within the territories under government control. Illegal operation is punishable by fine and/or imprisonment. Refer service to qualified technicians only. wet. Safety: It is important that the operator is aware of and understands hazards common to the operation of any transceiver. preCaUtions Do not charge the transceiver and battery pack when they are Ensure that there are no metallic items located between the transceiver and the battery pack. Do not use options not specified by Kenwood. If the die-cast chassis or other transceiver part is damaged, do not touch the damaged part. If a headset or headphone is connected to the transceiver, reduce the transceiver volume. Pay attention to the volume level when turning the squelch off. Do not place the microphone cable around your neck while near machinery that may catch the cable. Do not place the transceiver on unstable surfaces. Ensure that the end of the antenna does not touch your eyes. When the transceiver is used for transmission for many hours, the radiator and chassis will become hot. Do not touch these locations when replacing the battery pack. Do not immerse the transceiver in water. Always switch the transceiver power off when installing optional accessories.
v Turn the transceiver power off in the following locations:
In explosive atmospheres (inflammable gas, dust particles, metallic powders, grain powders, etc.). While taking on fuel or while parked at gasoline service stations. Near explosives or blasting sites. In aircrafts. (Any use of the transceiver must follow the instructions and regulations provided by the airline crew.) Where restrictions or warnings are posted regarding the use of radio devices, including but not limited to medical facilities. Near persons using pacemakers. Do not disassemble or modify the transceiver for any reason. Do not place the transceiver on or near airbag equipment while the vehicle is running. When the airbag inflates, the transceiver may be ejected and strike the driver or passengers. Do not transmit while touching the antenna terminal or if any metallic parts are exposed from the antenna covering. Transmitting at such a time may result in a high-frequency burn. If an abnormal odor or smoke is detected coming from the transceiver, switch the transceiver power off immediately, remove the battery pack from the transceiver, and contact your Kenwood dealer. Use of the transceiver while you are driving may be against traffic laws. Please check and observe the vehicle regulations in your area. Do not expose the transceiver to extremely hot or cold conditions. Do not carry the battery pack (or battery case) with metal objects, as they may short the battery terminals. When operating the transceiver in areas where the air is dry, it is easy to build up an electric charge (static electricity). When using an earphone accessory in such conditions, it is possible for the transceiver to send an electric shock through the earphone and to your ear. We recommend you use only a speaker/microphone in these conditions, to avoid electric shocks. v Contents UNPACkINg AND CHECkINg EqUIPmENT ...........................1 supplied Accessories ............................................................1 ORIENTATION ...........................................................................2 displAy ..................................................................................3 PREPARATION ..........................................................................4 BAttery pAck precAutions ....................................................4 instAlling/ removing the BAttery pAck ..................................9 chArging the BAttery pAck .................................................10 instAlling/ removing the Belt clip ......................................11 instAlling/ removing optionAl Accessories .........................12 gETTINg STARTED ................................................................13 CHANNEL FREqUENCY SETUP ............................................15 qUIET TALk/ DIgITAL qUIET TALk .......................................16 SCANNINg THE CHANNELS .................................................17 revert chAnnel ..................................................................18 mONITORINg A CHANNEL .....................................................19 squelch level ....................................................................19 VOICE ACTIVATED CONTROL (VOX) ....................................20 vox operAtion ...................................................................20 vox gAin ...........................................................................20 vox delAy time ..................................................................21 vox trAnsmit inhiBit ..........................................................22 vox proceed tone ............................................................23 PRIVACY TALk ........................................................................24 CALL kEY SETUP ...................................................................25 cAlling Alert ......................................................................26 selcAll (selective cAlling) ................................................28 OPERATINg FEATURES ........................................................33 speAker mute .....................................................................33 trAnsmission power ............................................................33 compAnder ..........................................................................34 v
key lock .............................................................................34 super lock .........................................................................35 displAy BAcklight ................................................................35 microphone sensitivity .......................................................36 time-out timer ....................................................................37 BAttery sAve ......................................................................38 BAttery indicAtor ................................................................39 incoming cAll notificAtion type ..........................................40 Busy chAnnel lockout (Bcl) .............................................41 trAnsceiver Beep ................................................................41 mode reset time.................................................................42 RESETTINg THE TRANSCEIVER ..........................................43 OPTIONAL ACCESSORIES ....................................................44 mENUS ....................................................................................45 qT TONES/ DqT CODES ........................................................47 CHANNEL FREqUENCIES .....................................................49 SPECIFICATIONS ...................................................................50 TROUBLESHOOTINg gUIDE .................................................51 v
Unpacking and checking eqUipment Carefully unpack the transceiver. We recommend you identify the items listed in the following table before discarding the packing material. If any items are missing or have been damaged during shipment, file a claim with the carrier immediately. Supplied AcceSSorieS Item Belt clip Screw set KNB-46L battery pack KSC-37 rapid charger Warrany card Instruction manual Part Number Quantity J29-0736-XX N99-2063-XX B62-1976-XX 1 1 1 1 1 1 Belt clip Screw set KNB-46L battery pack KSC-37 rapid charger
ORientatiOn Antenna MENU key Press to perform various functions. Press and hold while switching the power ON to enter Setting Mode. CAL key Press before making a call to alert the other party members, or press to select a unit ID to make a call LED Indicator Indicates the transceiver status. Power switch/
Volume control Turn clockwise to switch the power ON and counter-
clockwise to switch the power OFF. Rotate to adjust the volume. MON key Press to monitor the current channel for activity. Microphone Speaker
/ keys Press to change the operating channel, to select a menu in Setting Mode, and to perform other functions. PTT (Push to Talk) switch Press and hold, then speak into the microphone to transmit. SP/MIC jacks Lift the covers and insert the accessory s plugs here.
diSplAy Icon Description Appears when VOX is activated. Appears when using low transmission power. Appears when the channel is set up with a DQT code. Appears when making or receiving a selcall. Displays the approximate battery power remaining. Blinks when the battery power is low. Appears when Privacy Talk is activated. Appears when the Callers ID is displayed. Displays the channel number along with its QT/DQT setting (if any). Also displays various menus and menu settings. Appears while monitoring a channel. Appears when the transceiver keys have been locked.
pRepaRatiOn BAttery pAck precAutionS Do not use battery packs or battery chargers not recommended by Kenwood. Do not recharge the battery pack if it is already fully charged. Doing so may cause the life of the battery pack to shorten or the battery pack may be damaged. After charging the battery pack, disconnect it from the charger. If the charger power is reset (turned ON after being turned OFF), recharging will start again and the battery pack will become overcharged. Do not use the transceiver while charging the battery pack. We recommend you switch the transceiver power OFF while charging is taking place. Do not charge the battery pack when the battery pack or transceiver is wet, to avoid the risk of fire or damage. Wipe the water from the battery pack or transceiver using a dry cloth before charging. Do not short the battery terminals or dispose of the battery by Never attempt to remove the casing from the battery pack. fire.
Information concerning the Li-ion battery pack:
The battery pack includes flammable objects such as organic solvent. Mishandling may cause the battery to rupture producing flames or extreme heat, deteriorate, or cause other forms of damage to the battery. Please observe the following prohibitive matters. DANGER Do not disassemble or reconstruct battery!
The battery pack has a safety function and protection circuit to avoid danger. If they suffer serious damage, the battery may generate heat or smoke, rupture, or burst into flame. Do not short-circuit the battery!
Do not join the + and terminals using any form of metal (such as a paper clip or wire). Do not carry or store the battery pack in containers holding metal objects (such as wires, chain-
necklaces or hairpins). If the battery pack is short-circuited, excessive current will flow and the battery may generate heat or smoke, rupture, or burst into flame. It will also cause metal objects to heat up. Do not incinerate or apply heat to the battery!
If the insulator is melted, the gas release vent or safety function is damaged, or the electrolyte is ignited, the battery may generate heat or smoke, rupture, or burst into flame. Do not use or leave the battery near fires, stoves, or other heat generators (areas reaching over 80C/ 76F)!
If the polymer separator is melted due to high temperature, an internal short-circuit may occur in the individual cells and the battery may generate heat or smoke, rupture, or burst into flame. Avoid immersing the battery in water or getting it wet by other means!
If the battery becomes wet, wipe it off with a dry towel before use. If the batterys protection circuit is damaged, the battery may charge at extreme current (or voltage) and an abnormal chemical reaction may occur. The battery may generate heat or smoke, rupture, or burst into flame.
DANGER Do not charge the battery near fires or under direct sunlight!
If the batterys protection circuit is damaged, the battery may charge at extreme current (or voltage) and an abnormal chemical reaction may occur. The battery may generate heat or smoke, rupture, or burst into flame. Use only the specified charger and observe charging requirements!
If the battery is charged in unspecified conditions (under high temperature over the regulated value, excessive high voltage or current over regulated value, or with a remodelled charger), it may overcharge or an abnormal chemical reaction may occur. The battery may generate heat or smoke, rupture, or burst into flame. Do not pierce the battery with any object, strike it with an instrument, or step on it!
This may break or deform the battery, causing a short-circuit. The battery may generate heat or smoke, rupture, or burst into flame. Do not jar or throw the battery!
An impact may cause the battery to leak, generate heat or smoke, rupture, and/or burst into flame. If the batterys protection circuit is damaged, the battery may charge at an abnormal current (or voltage), and an abnormal chemical reaction may occur. Do not use the battery pack if it is damaged in any way!
The battery may generate heat or smoke, rupture, or burst into flame. Do not solder directly onto the battery!
If the insulator is melted or the gas release vent or safety function is damaged, the battery may generate heat or smoke, rupture, or burst into flame. Do not reverse the battery polarity (and terminals)!
When charging a reversed battery, an abnormal chemical reaction may occur. In some cases, an unexpected large amount of current may flow upon discharging. The battery may generate heat or smoke, rupture, or burst into flame. 6 DANGER Do not reverse-charge or reverse-connect the battery!
The battery pack has positive and negative poles. If the battery pack does not smoothly connect with a charger or operating equipment, do not force it; check the polarity of the battery. If the battery pack is reverse-connected to the charger, it will be reverse-charged and an abnormal chemical reaction may occur. The battery may generate heat or smoke, rupture, or burst into flame. Do not touch a ruptured and leaking battery!
If the electrolyte liquid from the battery gets into your eyes, wash your eyes out with fresh water as soon as possible, without rubbing your eyes. Go to the hospital immediately. If left untreated, it may cause eye-problems. DANGER Do not charge the battery for longer than the specified time!
If the battery pack has not finished charging even after the regulated time has passed, stop it. The battery may generate heat or smoke, rupture, or burst into flame. Do not place the battery pack into a microwave or high pressure container!
The battery may generate heat or smoke, rupture, or burst into flame. Keep ruptured and leaking battery packs away from fire!
If the battery pack is leaking (or the battery emits a bad odor), immediately remove it from flammable areas. Electrolyte leaking from battery can easily catch on fire and may cause the battery to generate smoke or burst into flame. Do not use an abnormal battery!
If the battery pack emits a bad odor, appears to have different coloring, is deformed, or seems abnormal for any other reason, remove it from the charger or operating equipment and do not use it. The battery may generate heat or smoke, rupture, or burst into flame. 7 Using the Li-ion Battery pack Charge the battery pack before using it. To keep the battery discharge at a minimum, remove the battery pack from the equipment when it is not in use. Store the battery pack in a cool and dry location. When storing the battery pack for a long period:
Remove the battery pack from the equipment.
Discharge the battery pack, if possible.
Store the battery pack in a cool (below 25C/ 77F) and dry location. characteristics of the Li-ion Battery pack As the battery pack is charged and discharged repeatedly, the battery capacity decreases. Even if the battery pack is unused, the battery pack degrades. It takes a longer time to charge the battery pack in cooler areas. The life of battery pack is shortened when it is charged and discharged in hotter areas. When the battery pack is stored in a hot location, the battery pack degrades quicker. Do not leave the battery pack in vehicles or near heating appliances. When the battery pack operating time becomes short, even if it is fully charged, replace the battery pack. Continuing to charge and discharge the battery pack may result in electrolyte leakage. 8 inStAlling/ removing the BAttery pAck The battery pack is not charged at the factory; charge it before use {page 10}. Average battery pack life using low power: 12 hours Average battery pack life using high power: 10 hours Average times are calculated using 5% transmit time, 5% receive time, and 90% standby time. Do not short the battery terminals or dispose of the battery by Never attempt to remove the casing from the battery pack. fire.
Match the guides of the battery pack with the corresponding grooves on the upper rear of the transceiver, then firmly press the battery pack to lock it in place.
To remove the battery pack, lift the safety catch, press the release latch, then pull the battery pack away from the transceiver.
chArging the BAttery pAck Initially charging the battery pack after purchase or extended storage (greater than 2 months) will not bring the battery pack to its normal operating capacity. After repeating the charge/
discharge cycle two or three times, the operating capacity will increase to normal. Do not recharge the battery pack if it is already fully charged. Doing so may cause the life of the battery pack to shorten or the battery pack may be damaged. After recharging the battery pack, disconnect it from the charger. Charging the battery pack for more than 5 days may reduce the battery pack life due to overcharging. Note:
The ambient temperature should be between 41F and 104F
(5C and 40C) while charging is in progress. Charging outside this range may not fully charge the battery. Always switch OFF the transceiver equipped with a battery pack before charging. Using the transceiver while charging its battery pack will interfere with correct charging. The battery pack life is over when its operating time decreases even though it is fully and correctly charged. Replace the battery pack.
Plug the AC adapter cable into the adapter jack located on the rear of the charger.
Plug the AC adapter into an AC outlet.
0
Slide a battery pack or a transceiver equipped with a battery pack into the battery pack slot. Make sure the metal contacts of the battery pack mate securely with the charger terminals. The indicator lights red and charging starts.
When charging is completed, the indicator lights green. Remove the battery pack or the transceiver from the battery pack slot. It takes approximately 2.5 hours to charge the battery pack. When the charger will not be used for a long time, unplug the AC adapter from the AC outlet. inStAlling/ removing the Belt clip If desired, attach the belt clip to the rear of the transceiver using the 2 supplied screws. Charger terminals Indicator
inStAlling/ removing optionAl AcceSSorieS Note: Always switch OFF the transceiver power when installing or removing optional accessories. The following accessories can be used with this transceiver:
KMC-17 Speaker-Microphone KMC-21 Speaker-Microphone KHS-22 Headset KHS-28F Headset EMC-3 Clip Microphone with Earphone EMC-6 Clip Microphone with Earphone To install these accessories:
Open the SP/MIC tabs on the side of the transceiver.
When you remove the accessory from the transceiver, be sure to cover the SP/MIC jacks with the attached tabs, in order to keep dust and dirt away from the contacts. Insert the accessorys plugs into the SP/MIC jacks. Note: Refer to the accessory instruction manuals for detailed instructions on each of these accessories.
getting StaRted q Switch the Power ON. Switch the transceiver power ON by turning the Power switch/ Volume control clockwise. A confirmation tone sounds, the LCD lights up momentarily, then the current channel number is displayed. To switch the transceiver power OFF, turn the Power switch/ Volume control fully counterclockwise, until a click sounds. w Adjust the Volume. Set your desired volume level by rotating the Power switch/ Volume control. Clockwise increases the volume and counterclockwise decreases the volume. Note: To adjust the volume using background noise as a reference, use the Monitor function {page 19}. e Select a Channel. Select a channel by pressing the keys. or A confirmation tone sounds each time you press the or key.
When you receive a call on your selected channel, you will hear audio from the speaker and the LED will light green. To use a signalling code, refer to QUIET TALK/
DIGITAL QUIET TALK on page 16. r Make a Call.
Press the MON key to make sure the channel is not in use {page 19}.
Press and release the CAL key to alert the other parties that you are beginning a call. A calling alert tone will sound on the other partys transceiver.
Press and hold the PTT switch, then speak into the microphone to transmit. The LED lights red while transmitting. For best sound quality, speak into the microphone in your normal speaking voice while holding the microphone approximately 1.5 inches (3 to 4 cm) from your lips.
Release the PTT switch when you have finished speaking.
channeL fReqUency SetUp You can change the default frequency of each channel:
With the transceiver power OFF, press and hold the MENU key (for approximately 1 second) while turning the transceiver ON. or key to select a channel.
Press the The current frequency list number appears beside the channel number.
Press the MENU key then press or frequency list number for the channel. to select the Refer to page 49 for the frequencies available for each channel.
Press the MENU key to confirm the selection, then repeat steps 3 and 4 to set additional channels.
Press the PTT, MON, or CAL key to exit Setting Mode.
qUiet taLk/ digitaL qUiet taLk QT (Quiet Talk) and DQT (Digital Quiet Talk) are functions that reject signals from undesired parties that are using the same channel as you. You will hear audio from the speaker only when you receive a signal that contains a tone or code matching the one set up on the channel you are using. Likewise, when you transmit on a channel set up with QT or DQT, the receiving station must have a matching tone or code in order to hear your signal. You can select a tone or code for each channel. There are 39 QT tones and 83 DQT codes. After changing the QT/ DQT setting, confirm that the other members in your group have selected the same tone or code.
Press the MENU key. The current setting blinks.
Press the or key to select your desired value. The values range from 01 to 39 for QT tones, then proceed to 01 to 83 for DQT codes. When selecting a DQT code, the icon appears on the display. Select oF to turn off both QT and DQT. Refer to pages 47 and 48 for the tones/codes corresponding to the QT/DQT numbers.
Press the MENU key 4 times, or press the PTT, MON, or CAL key to confirm the selection and return to operating mode.
6 Scanning the channeLS You can scan the transceiver channels to search for a signal. When the transceiver verifies a signal on a channel, it proceeds to check whether or not its QT/ DQT setting matches that which is set up on your transceiver (if you have set a channel with QT/ DQT). If the QT/ DQT matches, the transceiver stops at the channel and opens the squelch so you can listen to the call. If the QT/ DQT does not match, the call is ignored and scanning continues. Before you can use the scan function, ensure that it is activated. You can turn the scan function (the ability to perform scan) ON or OFF in Setting mode.
With the transceiver power OFF, press and hold the MENU key while turning the transceiver power ON (for 1 second).
Press the or key to select SC.
Press the MENU key then press to select SC-oF
(scan function disabled) or SC-on (scan function enabled). or If you select SC-oF, you will no longer be able to perform scan by pressing and holding the key {page 18}.
Press the MENU key to confirm the selection.
Press the PTT, MON, or CAL key to exit Setting Mode.
7 To begin scanning:
Press and hold the key for 1 second. SCAn appears on the display.
When a signal is detected and the QT/ DQT matches, the channel number appears on the display and blinks.
When the signal is no longer present, the transceiver waits for 5 seconds before scanning continues. If a new signal appears before the 5 seconds elapse, the transceiver will remain on the channel until the new signal is no longer present, at which time it will again wait for 5 seconds before continuing.
To end the scan at any time, press and hold the 1 second. The transceiver returns to the channel you were using before key for you started scanning. revert chAnnel The revert channel is the channel from which you start scanning. So, for example, if you are on channel 1 when you begin to scan, your revert channel is channel 1. During scan, pressing the PTT switch will automatically select the transceivers revert channel (in the above example, channel 1) and you will begin transmitting. However, if you are currently paused on another channel after having received a signal (for example, channel 2), pressing the PTT switch will allow you to transmit on that channel, rather than returning to the revert channel. Scanning will resume after 5 seconds, unless a signal is present on the channel.
8 mOnitORing a channeL When no signals are present, the squelch on the transceiver automatically mutes the speaker so you will not hear background noise. Using the MON key, you can open the squelch to unmute the speaker. This allows you to:
confirm the channel activity so you dont make a call while another party is using the same channel adjust the volume level without having to wait for a call listen to an intermittent call (due to a weak signal) without it continuously cutting out To manually open the squelch, press and hold the MON key. When squelch is open, the icon appears on the display and the LED lights green. To return to normal operation, release the MON key. Squelch level You can adjust the default squelch level of the transceiver.
With the transceiver power OFF, press and hold the MENU key while turning the transceiver power ON (for 1 second).
Press the or key to select Sq.
Press the MENU key then press or to select Sq- 0
(open), Sq- 1 (default setting), or Sq- 2 (tight).
Press the MENU key to confirm the selection.
Press the PTT, MON, or CAL key to exit Setting Mode.
VOice actiVated cOntROL (VOX) Using the VOX feature, you can operate the transceiver hands-free. In order to use this feature, however, you must use an optional headset; VOX will not function with the built-in microphone. For best operation conditions, we recommend you use an optional headset with both an ear piece and a microphone on a boom that rests in front of your mouth. voX operAtion
Set up a VOX gain level from 1 to 5 {below}.
To transmit, speak into the headset microphone. You do not need to press the PTT switch; the transceiver automatically detects your voice and begins transmitting.
To stop transmitting, stop speaking. Transmission will continue momentarily after you stop speaking. You can select the delay time as described above.
To exit VOX mode, set the VOX gain level {below} to GL-oF (VOX function off). voX gAin With VOX activated, your voice level will determine when you transmit. Due to the automatic switching between transmission and reception, we recommend you set the VOX gain such that it will not activate when in an area with excessive ambient noise.
With the transceiver power OFF, press and hold the MENU key while turning the transceiver power ON (for 1 second).
Press the or key to select GL.
0
Press the MENU key then press to select GL-oF
(VOX function off) or GL- 1 (VOX gain level 1) to GL- 5
(VOX gain level 5). or While adjusting the VOX Gain, speak into the microphone. When an appropriate level is reached, the LED lights orange. Setting the VOX gain to OFF deactivates VOX. In order to transmit with VOX turned off, you must use the PTT switch.
Press the MENU key to confirm the selection.
Press the PTT, MON, or CAL key to exit Setting Mode. voX delAy time If the transceiver returns to receive mode too quickly after you stop speaking, the end of your message may not be transmitted. To avoid this, select an appropriate delay time that allows your entire message to be transmitted. However, do not make the delay overly long.
With the transceiver power OFF, press and hold the MENU key while turning the transceiver power ON (for 1 second).
Press the or key to select dY.
Press the MENU key then press or to select dY-0.1
(0.1 seconds), dY-0.3 (0.3 seconds), dY-0.5
(0.5 seconds), dY-1.0 (1 second), dY-1.5 (1.5 seconds), or dY-3.0 (3 seconds).
While adjusting the VOX Delay Time, speak into the microphone to simulate transmitting. The LED lights orange while speaking, but no signal is transmitted at this time.
Press the MENU key to confirm the selection.
Press the PTT, MON, or CAL key to exit Setting Mode. voX trAnSmit inhiBit While using VOX, you can set the transceiver to detect when the channel is in use (in place of using the Monitor function). With this function turned on, VOX will not allow you to transmit while the channel is being used. You can transmit only when the channel is free. Setting up the proceed tone function
{page 23} will notify you when the channel is free.
With the transceiver power OFF, press and hold the MENU key while turning the transceiver power ON (for 1 second).
Press the or key to select tI.
Press the MENU key then press or to select tI-on
(transmit inhibit on) or tI-oF (transmit inhibit off).
Press the MENU key to confirm the selection.
Press the PTT, MON, or CAL key to exit Setting Mode.
voX proceed tone You can set the transceiver to sound an alert tone when you are able to transmit (transmission is no longer inhibited).
With the transceiver power OFF, press and hold the MENU key while turning the transceiver power ON (for 1 second).
Press the or key to select Pd.
Press the MENU key then press to select Pd-on
(VOX proceed tone on) or Pd-oF (VOX proceed tone off). or You can speak into the microphone at this time to simulate transmitting. The LED lights orange while speaking if your voice is at an appropriate level, but no signal is transmitted at this time.
Press the MENU key to confirm the selection.
Press the PTT, MON, or CAL key to exit Setting Mode.
pRiVacy taLk Whereas the Quiet Talk and Digital Quiet Talk functions
{page 16} allow you to ignore unwanted calls, Privacy Talk allows you to hold a conversation in complete privacy. When activated, the transceiver scrambles your voice so that anybody listening to your conversation will not be able to understand what you are saying. In order for members of your own group to understand your call while you are using Privacy Talk, all other members must also activate Privacy Talk on their transceivers. This scrambles everybodys voice while transmitting and descrambles the voice message on your own transceiver when you receive the message.
Press the MENU key 2 times. The icon appears on the display and blinks.
Press the
(privacy off). or key to select on (privacy on) or oF
Press the MENU key 3 times, or press the PTT, MON, or CAL key to confirm the selection and return to operating mode.
caLL key SetUp You can set up the transceiver CAL key to perform 1 of 2 functions, or you can turn the CAL key off (unused):
Calling Alert: Press the CAL key before making a call will send your calling alert tone to your party members, identifying yourself before speaking. Selcall: Press the CAL key then select from a list of IDs to make calls to specific transceivers. To set up the CAL key:
With the transceiver power OFF, press and hold the MENU key while turning the transceiver power ON (for 1 second).
Press the or key to select CL.
Press the MENU key then press or to select CL-CA
(calling alert), CL-SC (selcall), or CL-oF (off).
Press the MENU key to confirm the selection.
Press the PTT, MON, or CAL key to exit Setting Mode.
cAlling Alert Calling alert tones are used to identify yourself to your party members. You can set up a calling alert tone to one of 10 types. If each party member uses a different calling alert tone, it is easy to know who is making the call. Pressing the CAL key before making a call will send your calling alert tone to your party members. To set up your own calling alert tone:
With the transceiver power OFF, press and hold the MENU key while turning the transceiver power ON (for 1 second).
Press the or key to select CA.
Press the MENU key then press to select CA-oF"
(calling alert off) or CA- 1 (calling alert tone 1) to CA-10
(calling alert tone 10). or Each time you press new tone sounds. or to select a calling alert tone, the
Press the MENU key to confirm the selection.
Press the PTT, MON, or CAL key to exit Setting Mode.
6 cAlling Alert Side tone When the CAL key is pressed, the calling alert tone will sound through your own speaker as well. To turn the Calling Alert Side Tone on or off, on your own transceiver:
With the transceiver power OFF, press and hold the MENU key while turning the transceiver power ON (for 1 second).
Press the key to select CS. or
Press the MENU key then press to select CS-on (Calling Alert Side Tone is on) or CS-oF
(Calling Alert Side Tone is off). or
Press the MENU key to confirm the selection.
Press the PTT, MON, or CAL key to exit Setting Mode.
7 SelcAll (Selective cAlling) A Selcall is a voice call to a particular station or group of stations. Each transceiver is set up with an individual ID number for use with selcalls. mAking A SelcAll
Press the CAL key.
Press the or key to select an ID number. Id represents a single station, GP represents a group of stations, and AL represents all stations.
Press the PTT switch to transmit the selected selcall ID. The transceiver waits for the Data Transmit Modulation Delay time {page 29} before transmitting the selcall ID. The side tone sounds if PTT ID side tone {page 30} is enabled.
Release the PTT switch, then continue the call as normal when you receive a response.
Press the CAL key to end the call. Note: If Optional Signalling (menu oP) has been set to FS
(FleetSync), you can also set up an Individual Selcall Alert type (menu IA) and Group Selcall Alert type (menu GA). Individual and Group Selcall Alert types range from -oF (off) and - 1 (type 1) to -10 (type 10). Refer to the menu list on page 45.
8 receiving A SelcAll When a selcall is received, the display along with the ID of the caller. icon appears on the Press the PTT switch and speak into the microphone to respond to the call, then continue the call as normal. When the call is finished, press the CAL key to end the call. dAtA trAnSmit modulAtion delAy time To set up a data transmit modulation delay time:
With the transceiver power OFF, press and hold the MENU key while turning the transceiver power ON (for 1 second).
Press the key to select dt. or
Press the MENU key then press to select dt- 0 (0 ms), dt- 5 (500 ms), dt-10 (1000 ms), dt-15 (1500 ms), or dt-20 (2000 ms). or
Press the MENU key to confirm the selection.
Press the PTT, MON, or CAL key to exit Setting Mode.
ptt id The transceiver can send a PTT ID signal when pressing the PTT switch (beginning of transmission) or when pressing and releasing (beginning of transmission and end of transmission) the PTT switch.
With the transceiver power OFF, press and hold the MENU key while turning the transceiver power ON (for 1 second).
Press the key to select Pt. or
Press the MENU key then press or to select Pt-oF (PTT ID is off), Pt-bo (send your own PTT ID at the beginning of transmission), or Pt-LI (send the list PTT ID at the beginning and end of transmission).
Press the MENU key to confirm the selection.
Press the PTT, MON, or CAL key to exit Setting Mode. ptt id Side tone When the PTT switch is pressed and/or released, a tone will sound through your own speaker when the PTT ID is transmitted. To turn the PTT ID Side Tone on or off:
With the transceiver power OFF, press and hold the MENU key while turning the transceiver power ON (for 1 second).
0
Press the or key to select St.
Press the MENU key then press or to select St-on (PTT ID Side Tone is on) or St-oF (PTT ID Side Tone is off).
Press the MENU key to confirm the selection.
Press the PTT, MON, or CAL key to exit Setting Mode. mute hold time Mute Hold Time keeps the speaker muted for a brief moment, after a signal has been received. This prevents interference with the PTT ID signal. To set the hold time:
With the transceiver power OFF, press and hold the MENU key while turning the transceiver power ON (for 1 second).
Press the key to select Hd. or
Press the MENU key then press or to select Hd-oF (hold time is off), Hd- 5 (500 ms), Hd-10
(1000 ms), Hd-15 (1500 ms), Hd-20 (2000 ms), or Hd-25 (2500 ms).
Press the MENU key to confirm the selection.
Press the PTT, MON, or CAL key to exit Setting Mode. cAller id If set up by your dealer, when the transceiver receives a PTT ID signal, the caller ID of that signal appears on the display, along with the making the call. To turn Caller ID on or off:
With the transceiver power OFF, press and hold the icon, so you know who is MENU key while turning the transceiver power ON (for 1 second).
Press the key to select CI. or
Press the MENU key then press to select CI-on (Caller ID is on) or CI-oF (Caller ID is off). or
Press the MENU key to confirm the selection.
Press the PTT, MON, or CAL key to exit Setting Mode.
OpeRating featUReS SpeAker mute If Speaker Mute is activated by your dealer, no sound will be emitted from the transceiver speaker. In order to hear any received signals, you must use a headset. trAnSmiSSion power You can adjust the transmission power on all channels. Selecting low power will allow longer use of the battery pack. Selecting high power will allow you to transmit farther, in case the other party is too far away for low power usage. To change the transmission power:
Press the MENU key 3 times.
Press the
(high power). or key to select Lo (low power) or HI The selected. icon appears on the display when low power is
Press the MENU key 2 times, or press the PTT, MON, or CAL key to confirm the selection and return to operating mode.
compAnder The compander (compressor/expander) allows higher clarity of signals, avoiding excessive noise and interference. When activated, transmitted signals are compressed before being sent and received signals are expanded when they arrive.
Press the MENU key 4 times.
Press the or key to select CP-oF (compander off) or CP-on (compander on.
Press the MENU key 1 time, or press the PTT, MON, or CAL key to confirm the selection and return to operating mode. key lock You can lock the MENU, accidentally changing the operating mode and channel settings. The Power switch/ Volume control and PTT, CAL, and MON still function normally. Press and hold the MENU key for 3 seconds to lock or unlock the transceiver keys. The icon appears on the display when the transceiver keys are keys to prevent
, and locked. No icon appears when they are unlocked.
Super lock You can lock the MENU, CAL, the Setting Mode. PTT and MON still function normally. To select the super lock setting:
With the transceiver power OFF, press and hold the PTT
, and/or keys, and disable switch and the CAL key while turning the transceiver power ON (for 1 second).
Press the or key to select SL- P (MENU, CAL,
, keys locked), SL- C (MENU and CAL keys and locked), or SL-oF (super lock off).
Press the MENU, PTT, MON, or CAL key to exit Super Lock Setting Mode. The icon appears on the display when the transceiver keys are locked. No icon appears when they are unlocked. diSplAy BAcklight You can set the display backlight to remain off, remain on, or turn on when you press any key other than the PTT switch
(auto). When set to auto, the backlight remains on for 5 seconds after pressing a key, before turning off again. To select the backlight setting:
With the transceiver power OFF, press and hold the MENU (for approximately 1 second) key while turning the transceiver power ON.
Press the or key to select Lt.
Press the MENU key then press to select Lt-oF
(backlight off), Lt-on (backlight on), or Lt- A (backlight auto). or
Press the MENU key to confirm the selection.
Press the PTT, MON, or CAL key to exit Setting Mode. microphone SenSitivity You can adjust the sensitivity level of the transceiver microphone. To select the microphone sensitivity:
With the transceiver power OFF, press and hold the MENU key while turning the transceiver power ON (for 1 second).
Press the or key to select SE.
Press the MENU key then press
(normal) or SE-HI (high). or to select SE-no
Press the MENU key to confirm the selection.
Press the PTT, MON, or CAL key to exit Setting Mode.
6 time-out timer The Time-out Timer prevents you from using a channel for a extended durations. This function is useful, for example, when you accidentally keep the PTT switch pressed. Additionally, by limiting the amount of time you can continuously transmit, this feature helps you save on battery power consumption. If you continuously transmit for 3 minutes (default value), the transceiver will stop transmitting and a tone will sound. To stop the tone, release the PTT switch. You can press the PTT switch again to resume transmitting. To change the default value of 3 minutes:
With the transceiver power OFF, press and hold the MENU key while turning the transceiver power ON (for 1 second).
Press the or key to select to.
Press the MENU key then press
(3 minutes) or to-10 (10 minutes). or to select to- 3
Press the MENU key to confirm the selection.
Press the PTT, MON, or CAL key to exit Setting Mode. This transceiver is also equipped with a pre-alert tone which sounds 10 seconds before the Time-out Timer expires. This will allow you time to finish your message before the transceiver automatically stops transmitting.
7 BAttery SAve This transceiver has been designed to give you the most out of your battery power. The battery save function decreases the amount of power used when a signal is not being received and no operations are being performed. While using the transceiver, battery save will automatically switch ON after 5 seconds have elapsed with no operations or received calls. Operating the transceiver or receiving a call will switch this feature OFF until 5 seconds of non-operation occurs again. To turn this function on or off:
With the transceiver power OFF, press and hold the MENU key while turning the transceiver power ON (for 1 second).
Press the or key to select bS.
Press the MENU key then press or to select bS-on
(battery save on) or bS-oF (battery save off).
Press the MENU key to confirm the selection.
Press the PTT, MON, or CAL key to exit Setting Mode.
8 BAttery indicAtor When turned ON, the battery indicator on the display lets you know approximately how much battery life is remaining. When turned OFF, the battery indicator will appear and blink only when the battery voltage level is low. When the battery voltage becomes too low while transmitting, the transceiver stops transmitting, a tone sounds, and the LED blinks red until you release the PTT switch. Recharge or replace the battery pack at this time. High battery power Medium battery power Low battery power Recharge the battery pack To turn this function on or off:
With the transceiver power OFF, press and hold the MENU key while turning the transceiver power ON (for 1 second).
Press the or key to select bt.
Press the MENU key then press or to select bt-on
(battery indicator on) or bt-oF (battery indicator off).
Press the MENU key to confirm the selection.
Press the PTT, MON, or CAL key to exit Setting Mode.
incoming cAll notificAtion type Note: To use Incoming Call Notification, you must set up a QT tone or a DQT code {page 16}. Incoming Call Notification is used to inform you of when a call is being received. When activated, a tone is emitted when a busy signal is received and the QT/ DQT signalling matches. The tone will sound for 15 seconds before turning off. While the tone sounds, you will not hear any audio from the speaker. Press any key to turn the tone off and listen to the received call. After the call is finished, the transceiver will wait for 10 seconds before resetting. If you receive a new call within those 10 seconds, the tone will not sound. If no call is received within 10 seconds, Incoming Call Notification will reset so that the next time a call is received, the tone will sound again. To turn Incoming Call Notification on or off:
With the transceiver power OFF, press and hold the MENU key while turning the transceiver power ON (for 1 second).
Press the or key to select Ct.
Press the MENU key then press or to select Ct-oF
(incoming call notification off), or Ct-on (incoming call notification on).
Press the MENU key to confirm the selection.
Press the PTT, MON, or CAL key to exit Setting Mode.
0 BuSy chAnnel lockout (Bcl) This function is used in order to prevent transmitting on a channel that somebody else is currently using. When turned ON, a beep sounds when you press the PTT switch while another party is using the channel, and you cannot transmit. To turn BCL on or off:
With the transceiver power OFF, press and hold the MENU key while turning the transceiver power ON (for 1 second).
Press the or key to select bL.
Press the MENU key then press
(BCL on) or bL-oF (BCL off). or to select bL-on
Press the MENU key to confirm the selection.
Press the PTT, MON, or CAL key to exit Setting Mode. trAnSceiver Beep When you turn the transceiver power ON or press a key, a beep will emit from the transceiver. To turn the transceiver beep on or off:
With the transceiver power OFF, press and hold the MENU key while turning the transceiver power ON (for 1 second).
Press the or key to select bP.
Press the MENU key then press
(beep on) or bP-oF (beep off). or to select bP-on
Press the MENU key to confirm the selection.
Press the PTT, MON, or CAL key to exit Setting Mode. mode reSet time This function returns the transceiver to the channel display after a preset timer expires while in Menu mode or ID List mode. To set the mode reset timer:
With the transceiver power OFF, press and hold the MENU key while turning the transceiver power ON (for 1 second).
Press the or key to select rt.
Press the MENU key then press or to select rt-oF
(timer off), rt-10 (10 seconds), rt-30 (30 seconds).
Press the MENU key to confirm the selection.
Press the PTT, MON, or CAL key to exit Setting Mode.
ReSetting the tRanSceiVeR At some point in time, you may desire to reset the transceiver settings to their default values. (Default values are listed on pages 45 ~ 46.) To reset the transceiver:
With the transceiver power OFF, press and hold the
, and MON keys while turning the transceiver power ON. rESt (reset) will appear on the display.
Release the
, and MON keys. The confirmation message SUrE (sure) will appear on the display.
Press the PTT switch to reset the transceiver. Press any other key to cancel the reset. Note: Reset will function even if Super Lock has been activated.
OptiOnaL acceSSORieS KNB-46L (Li-ion battery pack) KSC-37 (Rapid charger) KMC-17 (Speaker-microphone) KMC-21 (Speaker-microphone) EMC-3 (Clip mic with earphone) EMC-6 (Clip mic with earphone) KHS-22 (Headset) KHS-28F (Headset)
menUS Menu Name Settings Default Ref. Pg
2 2 3 4 F1 ~ F56 F1 ~ F56 Channel 1 Frequency Setting Channel 2 Frequency Setting 1 Channels 3 ~ 16 F1 ~ F56 Frequency Setting Optional Signalling OFF/ FS
(FleetSync) Individual Selcall Alert Group Selcall Alert OFF/ 1 ~ 10 Incoming Call Notification Type OFF/ 1 ~ 10 OFF/ ON (Tone) Call Key Calling Alert Tone Calling Alert Side Tone PTT ID PTT ID Side Tone Data TX Modulation Delay Time CA (Call Alert)/
SC (Selcall)/ OFF Type 1 ~ 10 ON/ OFF OFF/ bo (BOT)/
L1 (List 1) ON/ OFF 0/ 5 (500)/ 10
(1000)/ 15 (1500)/
20 (2000 ms) F2 F8 F9 ~ F22 OFF 1 2 OFF CA 1 ON OFF ON 500 ms 15 15 15 28 28 28 40 25 26 27 30 30 29
Menu Name Settings Default Ref. Pg Mute Hold Time Caller ID Display Mode Reset Time Time-out Timer Busy Channel Lockout Backlight Battery Indicator Battery Save Beep Scan Function VOX Gain VOX Delay Time OFF/ 5 (500)/ 10
(1000)/ 15 (1500)/
20 (2000)/ 25
(2500 ms) OFF/ ON OFF/ 10/ 30 sec 3/ 10 min OFF/ ON OFF/ ON/ A (Auto) OFF/ ON OFF/ ON OFF/ ON OFF/ ON OFF/ 1 ~ 5 0.1/ 0.3/ 0.5/ 1.0/
1.5/ 3.0 sec OFF/ ON Transmit Inhibit
(while receiving) VOX Proceed Time OFF/ ON Squelch Level Mic Sensitivity 0 ~ 2 no (Normal)/
HI (high) OFF OFF 10 sec 3 min OFF Auto ON OFF ON OFF OFF 1.0 sec OFF OFF 1 Normal 31 32 42 37 41 35 39 38 41 17 20 21 22 23 19 36 5 5 5 1 Menus 3 ~ 16 are not available on 2 channel models. 2 Menus IA and GA are not available if the oP menu is set to OFF. 3 Menu Ct is not available if oP menu is set to FleetSync. 4 Menu CA is not available if the CL menu is set to OFF or Selcall. 5 Menus dY, tI, and Pd are not available if the GL menu is set to OFF.
6 qt tOneS/ dqt cOdeS Display QT Freq. Display QT Freq. Display QT Freq. 167.9 Hz 173.8 Hz 179.9 Hz 186.2 Hz 192.8 Hz 203.5 Hz 210.7 Hz 218.1 Hz 225.7 Hz 233.6 Hz 241.8 Hz 250.3 Hz 69.3 Hz 67.0 Hz 71.9 Hz 74.4 Hz 77.0 Hz 79.7 Hz 82.5 Hz 85.4 Hz 88.5 Hz 91.5 Hz 94.8 Hz 97.4 Hz 100.0 Hz 103.5 Hz 107.2 Hz 110.9 Hz 114.8 Hz 118.8 Hz 123.0 Hz 127.3 Hz 131.8 Hz 136.5 Hz 141.3 Hz 146.2 Hz 151.4 Hz 156.7 Hz 162.2 Hz 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 01 02 03 04 05 06 07 08 09 10 11 12 13
7 Display DQT Code Display DQT Code Display DQT Code DQT 01 DQT 02 DQT 03 DQT 04 DQT 05 DQT 06 DQT 07 DQT 08 DQT 09 DQT 10 DQT 11 DQT 12 DQT 13 DQT 14 DQT 15 DQT 16 DQT 17 DQT 18 DQT 19 DQT 20 DQT 21 DQT 22 DQT 23 DQT 24 DQT 25 DQT 26 DQT 27 DQT 28 DQT 29 DQT 30 DQT 31 DQT 32 DQT 33 DQT 34 DQT 35 DQT 36 DQT 37 DQT 38 DQT 39 DQT 40 DQT 41 DQT 42 DQT 43 DQT 44 DQT 45 DQT 46 DQT 47 DQT 48 DQT 49 DQT 50 DQT 51 DQT 52 DQT 53 DQT 54 DQT 55 DQT 56 DQT 57 DQT 58 DQT 59 DQT 60 DQT 61 DQT 62 DQT 63 DQT 64 DQT 65 DQT 66 DQT 67 DQT 68 DQT 69 DQT 70 DQT 71 DQT 72 DQT 73 DQT 74 DQT 75 DQT 76 DQT 77 DQT 78 DQT 79 DQT 80 DQT 81 DQT 82 DQT 83 174N 205N 223N 226N 243N 244N 245N 251N 261N 263N 265N 271N 306N 311N 315N 331N 343N 346N 351N 364N 365N 371N 411N 412N 413N 423N 431N 432N 445N 464N 465N 466N 503N 506N 516N 532N 546N 565N 606N 612N 624N 627N 631N 632N 654N 662N 664N 703N 712N 723N 731N 732N 734N 743N 754N OFF 023N 025N 026N 031N 032N 043N 047N 051N 054N 065N 071N 072N 073N 074N 114N 115N 116N 125N 131N 132N 134N 143N 152N 155N 156N 162N 165N 172N oF
8 channeL fReqUencieS Setup Number 01 (CH 9) 02 (CH 1) 03 (CH 10) 04 (CH 11) 05 (CH 12) 06 (CH 13) 07 (CH 14) 08 (CH 2) 09 (CH 3) 10 (CH 4) 11 (CH 5) 12 (CH 6) 13 (CH 7) 14 (CH 8) 15 (CH 15) 16 (CH 16) 17 18 19 Frequency
(MHz) 464.5000 464.5500 467.7625 467.8125 467.8500 467.8750 467.9000 467.9250 461.0375 461.0625 461.0875 461.1125 461.1375 461.1625 461.1875 461.2125 461.2375 461.2625 461.2875 Setup Number 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 Frequency
(MHz) 461.3125 461.3375 461.3625 462.7625 462.7875 462.8125 462.8375 462.8625 462.8875 462.9125 464.4875 464.5125 464.5375 464.5625 466.0375 466.0625 466.0875 466.1125 466.1375 Setup Number 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 Frequency
(MHz) 466.1625 466.1875 466.2125 466.2375 466.2625 466.2875 466.3125 466.3375 466.3625 467.7875 467.8375 467.8625 467.8875 467.9125 469.4875 469.5125 469.5375 469.5625 Note: The marked CH numbers are the default channel settings.
SpecificatiOnS RF output power Low High Audio output power Frequency stability Operating voltage Dimensions
(projections not included) Weight (with KNB-46L) 500 mW 1.5 W 100 mW 2.5 ppm 3.3 V ~ 5.0 V 52 x 28.7 x 103.5 mm
(2.05 x 1.13 x 4.07 inches) 165 g (5.8 oz)
0 tROUBLeShOOting gUide Problem Cannot turn the transceiver power ON. Battery power dies shortly after charging. Cannot talk to or hear other members in your group. Other voices
(besides group members) are present on the channel. The transceiver is malfunctioning for no apparent reason. Solution The battery pack may be dead. Recharge or replace the battery pack. The battery pack may not be installed correctly. Remove the battery pack and install it again. The battery pack life is finished. Replace the battery pack with a new one. Make sure you are using the same frequency and QT/DQT setting as the other group members. Other group members may be using Privacy Talk. Turn on your transceivers Privacy Talk. Other group members may be too far away. Make sure you are within range of the other transceivers. Change the QT/DQT settings. Make sure all group members change the settings on their transceivers to match the new QT/DQT setting. Reset the transceiver as described on page 43
RADIO FREQUENCY ENERGY SAFETY INFORMATION This KENWOOD transceiver has been evaluated and complies with the standards listed below, in regards to Radio Frequency (RF) energy and electromagnetic energy (EME) generated by the transceiver.
FCC RF exposure limits for Occupational Use Only. RF Exposure limits adopted by the FCC are generally based on recommendations from the National Council on Radiation Protection and Measurements, & the American National Standards Institute.
FCC OET Bulletin 65 Edition 97-01 Supplement C
American National Standards Institute (C95.1 1992)
American National Standards Institute (C95.3 1992) This KENWOOD transceiver generates RF EME while transmitting. RF EME (Radio Frequency Electric &
Magnetic Energy) has the potential to cause slight thermal, or heating effects to any part of your body less than the recommended distance from this radio transmitters antenna. RF energy exposure is determined primarily by the distance to and the power of the transmitting device. In general, RF exposure is minimized when the lowest possible power is used or transmission time is kept to the minimum required for consistent communications, and the greatest distance possible from the antenna to the body is maintained. The transceiver has been designed for and is classified for Occupational Use Only. Occupational/ controlled exposure limits are applicable to situations in which persons are exposed to RF energy as a consequence of their employment, and such persons have been made aware of the potential for exposure and can exercise control over their exposure. This means you can use the transceiver only if you are aware of the potential hazards of operating a transceiver and are familiar in ways to minimize these hazards. This transceiver is not intended for use by the general public in uncontrolled environments. Uncontrolled environment exposure limits are applicable to situations in which the general public may be exposed to RF energy, or in which the persons who are exposed as a consequence of their employment may not be fully aware of the potential for exposure or cannot exercise control over their exposure. The following list provides you with the information required to ensure that you are aware of RF exposure and of how to operate this transceiver so that the FCC RF exposure limitations are not exceeded.
While transmitting (holding the PTT switch or speaking with VOX enabled), always keep the antenna and the radio at least 3 cm (1 3/16 inches) from your body or face, as well as from any bystanders. A LED on the top of the radio shows red when the transmitter is operating in both PTT and VOX modes.
Do not transmit for more than 50% of the total transceiver use time; transmitting over 50% of the total use time may exceed the limits in accordance to the FCC RF exposure requirements. Nominal transceiver operation is 5% transmission time, 5% reception time, and 90% stand-by time.
Use only the specified antenna for this transceiver; this may be either the antenna provided with the transceiver or another antenna authorized by KENWOOD. Use only KENWOOD authorized accessories (antennas, battery packs, belt clips, Speaker/ Mics or headsets etc.): When worn on the body, always place the radio in a KENWOOD recommended clip or carrying case meant for this product. The use of other than recommended or approved body- worn accessories may result in RF exposure levels which exceed the FCCs occupational/ controlled environment RF exposure limits. To ensure that your exposure to RF EME is within the FCC limits for occupational use, you must observe and adhere to the above points. Electromagnetic Interference Compatibility Electronic devices are susceptible to electromagnetic interference (EMI) if they are not adequately shielded or designed for electromagnetic compatibility. Because this transceiver generates RF energy, it can cause interference to such equipment.
Turn OFF your transceiver where signs are posted to do so. Hospitals and health care facilities use equipment that is sensitive to electromagnetic radiation.
Turn OFF your transceiver while on board an aircraft when so instructed. Use of the transceiver must be in accordance with airline regulations and/or crew instructions. B59-2420-00
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2007-06-22 | 460 ~ 470 | TNF - Licensed Non-Broadcast Transmitter Held to Face | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2007-06-22
|
||||
1 | Applicant's complete, legal business name |
Kenwood USA Corporation
|
||||
1 | FCC Registration Number (FRN) |
0004356960
|
||||
1 | Physical Address |
3970 Johns Creek Court
|
||||
1 |
Suwanee, Georgia 30024
|
|||||
1 |
United States
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
H******@atcb.com
|
||||
1 | TCB Scope |
B2: General Mobile Radio And Broadcast Services equipment in the following 47 CFR Parts 22 (non-cellular) 73, 74, 90, 95, 97, & 101 (all below 3 GHz)
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
ALH
|
||||
1 | Equipment Product Code |
383200
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
D**** W******
|
||||
1 | Title |
Senior Product Planning & Development Manager
|
||||
1 | Telephone Number |
67847********
|
||||
1 | Fax Number |
67847********
|
||||
1 |
d******@us.jvckenwood.com
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
Flom Test lab
|
||||
1 | Name |
H******** B********
|
||||
1 | Physical Address |
3356 N. San Marcos Pl.
|
||||
1 |
Chandler, Arizona 85225
|
|||||
1 |
United States
|
|||||
1 | Telephone Number |
480-9********
|
||||
1 | Fax Number |
480-9********
|
||||
1 |
h******@mflom.com
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | TNF - Licensed Non-Broadcast Transmitter Held to Face | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | VHF/UHF FM/AM Handheld/Portable/Mobile Tranceiver | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Power output listed is at the antenna terminal on the device. This transmitter has been tested for SAR compliance in Push-to-Talk and body-worn operating configurations with a specific antenna, and only satisfies SAR limit for Occupational/Controlled RF Exposure Environment. Device must operate at a duty factor not exceeding 50% and SAR compliance for body-worn operating configurations is limited to the specific belt-clip for this filing. This device must be restricted to work related operations in an Occupational/Controlled RF exposure Environment. All qualified end-users of this device must have the knowledge to control their exposure conditions and/or duration to comply with Occupational /Controlled SAR limit and requirements. A label, as described in this filing, must be displayed on the device to direct users to specific training information for meeting Occupational Exposure Requirements and users must be provided with the training information. The highest reported SAR values at 50% duty factor are - Face: 1.17 W/kg; Body-worn: 1.54 W/kg. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Compliance Testing, LLC
|
||||
1 | Name |
M****** S********
|
||||
1 | Telephone Number |
480-9********
|
||||
1 | Fax Number |
480 9********
|
||||
1 |
m******@compliancetesting.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 90,95A | BH | 460 | 470 | 1.69 | 2.5 ppm | 16K0F3E | |||||||||||||||||||||||||||||||||
1 | 2 | 90,95A | BH | 460 | 470 | 1.69 | 2.5 ppm | 11K0F3E |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC