FCC ID: OTM-8415421-24GTX 1/24 R/C Beetle Baja

Contents

-RC Vehicle (Vehicle) x 1

-RC Transmitter (Transmitter ) x 1

-Instruction Manual x 1

20M / 65FT

RANGE

RC Transmitter x 1

RC Vehicle x 1

Battery Precaution

1. Alkaline batteries are recommended to be used

2. Only batteries of the same or equivalent type as recommended are to be used

3. Do not mix alkaline, standard or rechargeable batteries

4. Do not mix old and new batteries or different type of batteries

5. Non-rechargeable batteries are not to be charged

6. If rechargeable batteries are to be used, they are only to be charged under adult supervision

7. Rechargeable batteries are to be removed from the product before they are charged

8. Be sure to insert batteries with correct polarities and always follow the battery manufacturer’s instructions

9. Remove all batteries from the Vehicle and Transmitter when not in use

10. Exhausted batteries are to be removed from the product

11. The supply terminals are not to be short-circuited

12. Dispose of batteries properly. Do not dispose the batteries in fire - it may cause them to explode or leak causing injury or damage

13. Battery installation and removal must only be done by adult

Battery Installation

For Vehicle (Fig. 1, 2 and Fig. 3)

Vehicle

2.4 GHz Transmitter

LED Battery

Indicator

Battery

Compartment

Lock

ON/OFF

1.5V

AA

Control Sticks

Fig. 2

+

+

+

+

Fig. 1

1. Switch OFF the power

2. Turn the lock on the battery cover to the

vertical position

3. Unscrew the screws on the battery cover

4. Open the battery cover

5. Install 4 new 1.5V “AA” batteries with correct

polarities (+/-) as shown inside the battery

compartment

6. Close the battery cover

7. Tighten the screws on the battery cover

8. Turn the lock back to the horizontal position

Fig. 3

Transmitter - Battery Installation

No.#84154 / 84155

How To Bind

6

1. Turn OFF the Vehicle and then install the batteries into the Vehicle and Transmitter.

2. Do not touch the wheels and turn ON the Vehicle. When the wheels run automatically, the pairing process completed and it is ready for playing.

3. As long as the batteries in both Vehicle and Transmitter are not removed, it is no need for pairing process after switching OFF the Vehicle. Just switch ON the Vehicle

and it will still be paired up with the Transmitter.

4. If the pairing process is not completed, please remove the batteries from the Vehicle and Transmitter and re-start the process. (Step# 1)

Direction Adjustment

4 X AA

For Vehicle

(Not Included)

2 X AAA

For Transmitter

(Not Included)

How To Play

1. Ensure that the ON/OFF Switches on the Vehicle and the

Transmitter are at the ON position.

2. Control the LEFT and RIGHT Sticks on the Transmitter for

3. The Play time is around 35 mins. Please drive the Vehicle back

movement. (Fig.5)

before battery exhausted.

4. The optimum control range is up to 20m (65 ft) outdoor.

5. Play on the clear water.

Transmitter

- Controls Forward /

Reverse speed on

left side of wheels

Fig. 5

- Controls Forward /

Reverse speed on

right side of wheels

Backward

Forward & Right Turn

Reverse & Right Turn

Forward & Left Turn

Reverse & Left Turn

Performance Tips

1. Do not drive on grass, dirt, sand, dusts or carpet.

2. Do not drive in windy or rainy weather.

3. Avoid direct impact the Vehicle with obstacles.

4. Switch OFF the power when not in use to prevent damage of Vehicle and Transmitter

due to leakage of electrolyte from batteries.

5. Remove all batteries from the Vehicle and Transmitter when not in use for long period.

6. Keep fingers, hair and loose clothing away from wheels.

7. The operating range can be affected by a variety of factors

a) Low Voltage of batteries in Transmitter or Vehicle

b) Interference from other items that emit radio frequency signals.

8. Outdoor usage is recommended in order to get optimum control range.

9. Recommend to play the vehicle on a clean and smooth surface.

10. Clean the battery compartment to make sure it is free from dust to prevent poor

contact of batteries

Cautions

1. Do not attempt to disassemble the Vehicle or Transmitter

2. Make sure the batteries are installed with correct polarities (+/-) as shown inside the

3. Remove the package and take out all accessories before giving the Vehicle and

battery compartment

Transmitter to child to play

The packaging and instruction manual contain important information. Please keep them

for future reference.

Warning! Choking Hazard. Not suitable for children under the age of 3 years due to

small parts.

We reserve the right to improve/amend specifications and colors without notice.

FCC label compliance statement:

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

- Reorient or relocate the receiving antenna

-

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

- Consult the dealer or an experienced radio/TV technician for help

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Increase the separation between the equipment and receiver

RSS-210 Compliance Statement:

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device.

Declaration of Conformity

The product is in conformity with the requirement of EU Directive 2014/53/EU.

Environmental notes:

The whole product also does not belong to household waste at the end of the product life.

You can return it at collection points for the recycling of electronic and electronical instruments

The symbol on the item, instruction manual, hangtag or packing is showing this clearly.

Materials should be recycled according to their respective markings.

Recycling of old devices or other re-use of materials contained therein represents an important

contribution to environmental protection.

Please ask at your local community for the correct collection point.

Disposal of batteries

Batteries should not be disposed of in the household waste. As the consumer you are legally obliged

to return batteries containing harmful substances and all other used batteries. You can hand in your

old batteries at public collection points in your area or wherever batteries are sold.

You will find these chemical abbreviations along with a crossed-out refuse bin on batteries

containing harmful substances:

Pb=Battery contains lead

Cd=Battery contains cadmium

Hg=Battery contains mercury

KIDZTECH TOYS MANUFACTURING LTD.

Room 802, 8/F, Inter-Continental Plaza,

94 Granville Road, TST East, Hong Kong.

Tel: (852) 27218868 info@kidztech.net

Made in China http://www.kidztech.net

US OFFICE:

1540 Forest Avenue,

River Forest, IL 60305, USA

Tel: 708-689-0085 Fax: 708-689-8172

Frequency band : 2405 - 2475 MHz

Maximum radio frequency power transmitted : <0 dBm

Conforms to the safety requirements of ASTM F963

KT-BB-26/07/2019-EN

3cm(w) x 2.5cm(h) FCC ID : OTM-8415421-24GTX This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Letter of Agency

"I, an officer of Kidztech Toys Manufacturing Ltd. do hereby authorize Intertek

Testing Services (Mr. Terry Chan / Koo Wai Ip / Kenneth Wong) to act on our

behalf in front of the Federal Communications Commission with respect to all

matters relating to certification of equipment under Part 15 and Part 18 of the FCC

Rules until further notice."

I further certify that no party (as defined in §1.2002(b) of CFR 47, 2004) to this

application, including myself, is subject to a denial of federal benefits, that includes

FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21

U.S.C.,862.

Dated this

day

of 20

By

Signature

Printed Name

Title

Remark: The person who signs this authorization letter must be the grantee contact of record in the Grantee Code

data base.

Dec 2013

Eric HoSenior Manager1Jun21

Technical Description

The Equipment Under Test (EUT), is a portable 2.4GHz Transmitter (Controller Unit)

for a RC car. The sample supplied operated on 66 channels, normally at 2410 -

2475MHz. The channels are separated with 1MHz spacing.

The EUT is powered by 2 x 1.5V AAA batteries. After switching on the EUT, the car will

be moved forward or backward and turned left and right based on the switches

pressed in the controller.

Antenna Type: Internal, Integral antenna

Antenna Gain: 0dBi

Nominal rated field strength is 98.3dBμV/m at 3m (Peak), 76.4dBμV/m at 3m (Average)

Maximum allowed production tolerance: +/- 3dB

The brief circuit description is listed as follows:

1. U1 acts as MCU

2. Y1 acts as 12MHz Oscillator

3. C4, C5, C9 and L1 act as antenna matching circuit