FCC ID: 2A78TQBRS663 QB-RS663 Card Reader Module

Kunshan QuanBao Electronic Ltd. Product Technical Specification Confirmation Product Name Product Model QB-RS663 Card Reader Module Product SN QB-RS663 QB-RS663-V0.1A Kunshan QuanBao Electronic Ltd. Address:No. 515, Lidu Road, QianDeng Town, Kunshan City Tel: 0512-57279908 1 Kunshan QuanBao Electronic Ltd. 1.Product Introduction OM9663 is the main chip used on QB-RS663 RFID reader model.OM9663 is the multi-

protocol RF read card IC launched by NXP company.It is RF card reading IC with most supported protocols so far. OM9663 is a highly integrated transceiver chip, which is used on non contact communication for 13.56MHz. It directly drives the external antenna through the built-in transmitter to communicate with ISO/IEC 14443A or MIFARE card without additional active circuit.The digital module is responsible for all ISO/IEC 14443A framing and error detection function(parity check and CRC ) 2.Product Characteristics Support SO/IEC 14443A/MIFARE as MIFARE Classic 1KMIFARE Classic 4KMIFARE UltralightMIFARE Ultralight CMIFARE PLUS and MIFARE DESFire;

Support SO/IEC 14443IB Support the demodulation and decoding of felica coded signal. FeliCa receiver devices provide demodulation and decoding circuits for FeliCa coded signals.It supports FeliCas higher two-way transmission speed up to 424k bits/s. Support the passive initiator mode corresponding to ISO/IEC 18092 Support ISO/IEC 15693 Support the P2P passive initiator mode consistent with ISO/IEC 18092 Support the close range communication protocol consistent with ISO/IEC 15693 EPC UID and ISO/IEC 18000-3 mode 3/ EPC Class-1 HF. 2 Kunshan QuanBao Electronic Ltd. 3.Product Technical Specification Electrical Specifications Working Current Idle Current Sleep Current Peak Current Working Frequency Communication Distance Mechanical Specifications Product Size Working Temp() Storage Temperature() 4.Product Picture 40-60mA@ DC 12V 5-10mA@DC 12V

<80uA

<80mA 13.56MHz +/- 0.3KHz 4.5cm@DESFire 65mm42mm6mm

-40~85

-40~85 Device-Layer View 3 Kunshan QuanBao Electronic Ltd. Antenna-Layer View 5.Product Specification Chart 6.Pin Definition Diagram 4 Kunshan QuanBao Electronic Ltd. SN 1 Pin Name Function

+12V Power supply 2 3 4 5 GND RXD TXD GND Power supply ground RS232 RXD RS232 TXD Power supply ground The power supply current should more than 100mA,LDO is recommend User TXD User RXD 7.Communication protocol The communication is initiated by the host computer (command packet)and the reader-

board returns ACK data (response packet) after receiving the command. Command packet 0x02 CMD LEN DATA LRC 0x03 explain 0x02starting character CMDcommand code LEN2-byte DATA field length DATAData field( optional field, when LEN is 0x0000, data field has no data) LRCParity Check Codes, byte by byte or value of all data in the packet (excluding the start character of 0x02 and the end character of 0x03) 0x03terminator Response packet 0x02 CMD STATUS LEN DATA LRC 0x03 explain 0x02starting character CMDcommand code, same as the command code in the command package to be answered STATUSstatus code: success code 0x00 and failure code 0x5A LEN2 bytes DATA field length 5 Kunshan QuanBao Electronic Ltd. DATAdata field (optional fields: there is no data in the data field when LEN is 0x0000) LRCParity Check Codes, byte by byte or value of all data in the packet (excluding the start character of 0x02 and the end character of 0x03) 0x03terminator Card type:

= 0x4400-Mifare_UltraLight

= 0x0400-Mifare_One(S50)

= 0x0200-Mifare_One(S70)

= 0x0800-Mifare_Pro(X))

= 0x4403-Mifare_DESFire M1/CPU M1 CPU M3 8.Command Table 1. Get device information Used to get the software version number command CMD DATA nothing answer DATA software version number 0x01 2. Card search 0x10 Check whether there is a card in the range of card reading command:

CMD DATA nothing answer:

STATUS: 0x00 success 0x5A: No card

(when the card search is successful)DATA Card Type 2 byte card types 6 Kunshan QuanBao Electronic Ltd. Uid_Len Uid 1 byte uid length card unique identification number Explain: After receiving the command, the card reader enters the automatic card searching state and returns the response. It will continue the automatic card search later. It returns new result when the card search result changes (from card to card free, or from card free to card present). 3. Contactless CPU /M3 card reset 0x11 command CMD DATA nothing answer DATA card reset response data 4. CPU card command interaction command CMD 0x12 DATA CPU card command answer DATA data returned by card after execution 5. M1 card verification password command CMD DATA Mode:

Sector:

0x13 password 1 byte 0x00 verify A password 0x04 verify B password 1 byte verify the sector number of the passbuf:

6 bytes password 7 Kunshan QuanBao Electronic Ltd. answer DATA nothing 6. M1 card reading command CMD 0x14 DATA Adr:

answer DATA R_Data:

7. M1 card writing command CMD 0x15 DATA Adr:

data answer DATA none 1 byte block number 16 bytes data 1 byte block number 16 bytes data 8. Desfire card AID choice command CMD 0x16 DATA AID:

answer DATA none 1 byte AID number 9. Desfire card key authentication command 8 Kunshan QuanBao Electronic Ltd. CMD DATA KNO 0x17 1 byte key number password 16 byte key number answer DATA password2:

16 byte encryption key 10. Desfire card key modification command CMD DATA KNO 0x18 1 byte key number password password2:

16 byte new key 16 byte encryption key(returned by key authentication) answer DATA none 11. Desfire card read file 0x19 command CMD DATA FNO answer DATA R_DATA:

12. Desfire card write file command CMD DATA FNO 0x1A W_DATA answer File 1 byte 32 byte data File 1 byte 32 bytes writing data 9 Kunshan QuanBao Electronic Ltd. DATA none 13. M1 card read file (merge instruction) 0x1B command CMD DATA Mode:

Sector:

Adr :

passbuf:

answer DATA 16 byte data 9.Flow Diagram 1 byte 0x00 verify A password 0x04 verify B password 1 byte sector for password verification 1 byte block number 6 bytes 10 Kunshan QuanBao Electronic Ltd. 1. Card reading process 11 Kunshan QuanBao Electronic Ltd. 2. Card Writing Process 12 Kunshan QuanBao Electronic Ltd. 10.Attention 1 As the electromagnetic wave in 13.56MHz band can be absorbed by water and other liquids, and also reflected by metals,so the antenna position of the card reader module should be as far away from liquid and metal as possible, with clearance above 2cm . 2The antenna is greatly affected by the installation structure.If the distance does not meet the requirements after assembling, please contact us for antenna matching immediately. And then carry out other certification work after adaptation.It is strongly recommended that the user carries out the adaptation in the sample stage.Please contact us for re adaptation, if the structure changes after adaptation. 3The energy requirement of writing data to the tag is much higher than that of reading data from the tag, so the writing distance is generally shorter than the reading distance and allowance should be reserved while assembling. 4-40~85 is the normal working temperature of the chip.There will be read-write instability if it is beyond the operating temperature range. Try to avoid using modules in extreme situations. 11. Statement 1. FCC 15.21 Information to user Please note that changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. 2. FCC 15.105 Information to the user (Class B) Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 13 Kunshan QuanBao Electronic Ltd. 3. RF exposure statement This equipment complies with radio frequency exposure limits set forth by the FCC for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the device and the user or bystanders. IC RSS-Gen 8.4 User Manual Notice for Licence-Exempt Radio Apparatus This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

(1)Lappareil ne doit pas produire de brouillage;

(2)Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. IC RSS-Gen 8.4 User Manual Notice for Licence-Exempt Radio Apparatus This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

(1)Lappareil ne doit pas produire de brouillage;

(2)Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. 4. 5. RSS-102 2.6 User Manual Requirements This equipment complies with radio frequency exposure limits set forth by the Innovation, Science and Economic Development Canada for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the device and the user or bystanders. This device must not be co-located or operating in conjunction with any other antenna or transmitter. Cet quipement est conforme aux limites d'exposition aux radiofrquences dfinies par la Innovation, Sciences et Dveloppement conomique Canada pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre le dispositif et l'utilisateur ou des tiers. Ce dispositif ne doit pas tre utilis proximit dune autre antenne ou dun autre metteur. 14

7 PA GND, TXO.RXD-GNO-+12V. G46, 8 IC: 28888-QBRS663 HVIN: QB-RS663 PMN: QB-RS663 Card Reader Module CAN ICES-003 (B)/NMB-003(B) GND.TXD.RXD.GND+H12V.. CO6, FCC ID: 2A78TQBRS663 This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2)This device must accept any interference received, ncluding interference that may cause undesired operation. _

Kunshan Quanbao Electronic Co., LTD Authority to Act as Agent Date: 20220824 TUV Rheinland of North America, Inc. 1279 Quarry Lane., Suite. A Pleasanton, CA 94566 To Whom It May Concern:

| appoint MS.Yanli Fan of TUV Rheinland (shanghai) Co., Ltd to act as our agent in the preparation of this application for equipment certification. | certify that submitted documents properly describe the device or system for which equipment certification is sought. | also certify that each unit manufactured, imported or marketed, as defined in the FCC or Industry Canadas regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, |

acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by TUV Rheinland Group, still resides with Kunshan Quanbao Electronic Co., LTD / 515 Lidu Road, Qiandeng Town, Kunshan City, Jiangsu Province, China For TCB applications, We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Date: 20220824 Agreement is valid for 12 months from the above date. By:

0. Shaobin Wang

(Signature) (Print name) account executive +86 18168708767

(Title) (Telephone) On behalf of:

Kunshan Quanbao Electronic Co., LTD

(Company Name) Page 1 of 1

Kunshan Quanbao Electronic Co., LTD Date: 20220824 Subject: Confidentiality Request for FCC ID: 2A78TQBRS663 and IC: 28888-QBRS663 Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC/IC application be held confidential. Type of Confidentiality Requested Exhibit Short Term (x] Permanent Block Diagrams Short Term (_| Permanent Internal Photos ***

_] Short Term | Permanent Operation Description/Theory of Operation _| Short Term [x] Permanent Tune-Up Procedure/Parts List

(_] Short Term ] Permanent Schematics

| Short Term (_] Permanent Users Manual***

__] Short Term n/a Test Setup

[_] Short Term n/a External Photos Kunshan Quanbao Electronic Co., LTD has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. (*** PAG only) Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of _n/a_ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TUV Rheinland in the event information regarding the product or the product is made available to the public. TUV Rheinland will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Sincerely, By: </tao bmn We Shaobin Wang

(Signature/Title)

(Print name) MS-0044715 Page 1 of 1 Revision 0