FCC ID: QHQ-LB1YM Communication Module

Laerdal Medical AS CAN CPU MODULE 2 20-19560 Simple operation manual 1. PCBA connection configuration PCBA TOP SIDE PCBA BOTTOM SIDE 2. Connection :

3. Putty_v0.78 Setsup Step 1: Unzip the attachment. Step 2: Run putty.exe Step 3: Enter the IP location and product name. Step 4: Enter root. Step 5: Select attachments rsp.ppk and rsa.pub Step 6: Go back to Session, press Save. Step 7: Go back to CPU2, press Open 3 Product Specifications CPU Module2_MB Feature PCB Items PCB Description 55 x 70 LAY:6 THICKNESS:1.6mm i.MX8M PLUS Quad lite Processor CPU NXP P/N: MIMX8ML4DVNLZAB, Cortex- A53 4 Cores, 1.8 Memory Type LPDDR4 2GB GHz, 0 to 95C, Mass storage Minimum 16 GByte non-volatile data storage Storage PMIC RTC ROM PMIC RTC SPI FLASH ROM 64Mb PMIC FOR i.MX8 PLUS

- NXP:PCA9450CHNY The unit have a RTC to be able to keep system time and date while the main CPU is turned off. Minimum 10BASE-T and 100BASE-TX full duplex according to Requirement IEEE802.3 Auto MDI / MDI-X (IEEE 802.3ab) Duplex mode auto negotiation Controller Microchip: KSZ9031 Ethernet Interconnect cable connector Aces Electronic Co, 85205-1070L, 1.25mm S/T Wire to board Connector connector 10 ckt Mates with Aces Electronic Co, 85206-1000 Interconnect pin out shown to the right Minimum 1 independent high-speed (1Mbit) CAN interface Requirement ISO 11898-2:2003 Software switchable 120R CAN termination required. CAN Connector CAN interface and power input 1x USB Type-C Requirement Support for dual role device (DRP) Support USB2.0 ,3.0 USB output voltage: 5V, max 900mA Power The port shall have over current protection USB Type-C Supports the following USB devices from software:

Device List Requirement

- USB HID device

- USB Mass Storage device

- USB Serial port device

- USB Hub

- USB Ethernet devices

- USB Audio devices 1x 6pin USB connector support 1.5A

- Pitch2.0mm S/T Wire to board connector USB 2.0 Connector Pinout show to the right [TBD]

VBUS_USB output voltage: 5V, max 900mA USB Port #2

- The port shall have over current protection VBUS_CAN : output voltage: Unregulated input voltage: 4.5V-

Power 17V, max1.5A

- The voltage enable shall be controllable from SW

- Default state at startup is output OFF Device List See as USB Type-C for list of USB host support Wifi: minimum Wifi 5 with PCIe interface Standards: Wi-Fi 5 or better (IEEE 802.11 a/b/g/n/ac) Frequency band: 2.4 GHz and 5 GHz Radio parameters: DFS on 5 GHz Antenna configuration: Dual antennas for split RX/TX or diversity Wifi/BT Requirement RX (MIMO/MISO) BT: minimum 5.0 with PCM interface Minimum Bluetooth 5.2 Radio control: SW shall be able to turn off TX radio (RF kill) PCM audio interface shall be connected to the CPU Antenna: TE:2-2118909 Wi-Fi 6/ 6E TRIPLE BAND EMBEDDED ANTENNA Module Murata: LBEE5XV1YM For debug and development purposes LED Requirement Green light to indicate the system is booting and running RGB programmable LED from CPU to indicate SW status Input voltage range: 6.15VDC 17VDC

(Standard voltage: 12VDC)

- The input voltage shall be measured at the pins of the input connector

- Reverse polarity and over-current protection

- ESD protection on the power signals The unit shall power up minimum 500 ms after the supply voltage rises above the minimum input voltage The unit shall power up when power is present The unit shall be able to measure the input voltage and input current. Connector pin-out shown to the right

- Connect SW to ground to turn on the unit

- Activating SW longer than 5-10 seconds will force power off the unit Power Requirement ON/OFF Connector Requirement The SWITCH input shall withstand the full max 17V input voltage non-destructively. It is close to the VBAT signal where a short circuit is foreseeable misuse Connector to a separate debug breakout board for development purposes. Debug An external breakout debug board shall be available providing connector Requirement access to

- UART serial console

- Necessary debug control signals (boot pin) Temperature and Humidity

- Operating temperature range: 0C to +60C ambient temperature

- Operating humidity: 5% 90% relative humidity (R.H.), condensing

- Storage and shipment temperature range: -20C to +85C Air pressure/Altitude

- The CPU module2 operate as intended in altitudes from sea level to altitude of 3500 m Thermal Environment Requirement

- The CPU module2 have provisions for implementing temperature transport when used with the high-performance option of the CPU (TBD). Unwanted Substances

- The CPU module2 compliant with RoHS Directive

(2011/66/EU) and REACH Regulation (1907/2006). Evidence of compliance shall be a signed declaration. Flammability resistance

- The PCB have flammability class V0 according to UL94. Vibration and shock

IEC60068-2-6 Certification Requirement Safety:

- US/Canada, LVD: IEC/62368-1 second edition

- EU/UK, CB: IEC/EN62368-1 second edition EMC:

- US/Canada, FCC/IC: FCC 15B/ICES-003

- EU/UK, CE/UKCA: EN 55032/35, EN301489-1/-17, BS EN 55032 /35(UKCA)

- NZ/AUS, RCM: AS/NZS CISPR 32

Japan, VCCI: VCCI CISPR 32

- Korea, KC(EMC+RF): KC RF:

- US, FCC: FCC 15C

- Canada, IC: RSS-247

- EU/UK, CE/UKCA: EN300328+EN301893/ FDS, EN 62311 /

EN62471

- China, SRRC: CMIIT

- NZ/AUS, RCM: AS/NZS 4268

Japan, VCCI: MIC 2.4G+5G+BT+BLE This product is not suitable for user operation and will be assembled, sold and shipped by Laerdal before sale. RF Exposure warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Radio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Innovation, Science and Economic Development Canada (ISED) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure conditions. (Antennas are greater than 20cm from a person's body). Informations concernant l'exposition aux frquences radio (RF) La puissance de sortie rayonne de l'appareil sans fil est infrieure aux limites d'exposition aux radiofrquences d'Innovation, Sciences et Dveloppement conomique Canada (ISDE). L'Appareil sans fil doit tre utilis de telle manire que le potentiel de contact humain pendant le fonctionnement normal soit minimis. Cet appareil a galement t valu et dmontr conforme aux limites d'exposition RF IC dans des conditions d'exposition mobile. (Les antennes sont plus de 20 cm du corps d'une personne). US Federal Communications Commission (FCC) Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Consult the dealer or an experienced radio/TV technician for help. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. CAN CPU Module 2 Contains FCC ID: QHQ-LB1YM Cautions This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. The use of shielded I/O cables is required when connecting this equipment to any and all optional peripheral or host devices. Failure to do so may violate FCC rules. RF Exposure warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. For Country Code Selection Usage (WLAN Devices) Notes The country code selection is for non-US models only and is not available to all US models. Per FCC regulation, all WiFi products marketed in US must be fixed to US operation channels only. Changes or modifications not covered in this manual must be approved in writing by the manufacturers Regulatory Engineering Department. Changes or modifications made without written approval may void the users authority to operate this equipment. Canada Industry Canada Rules This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Devel- opment Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Cautions for WLAN 5GHZ Device:

The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit. The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate. The worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in Section 6.2.2(3) shall be clearly indicated. Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement:

Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux. Le gain maximal dantenne permis pour les dispositifs utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer la limite de p.i.r.e. Le gain maximal dantenne permis (pour les dispositifs utilisant la bande 5725-5850 MHz) doit se conformer la limite de p.i.r.e. spcifie pour lexploitation point point et non point point, selon le cas. Les pires angles dinclinaison ncessaires pour rester conforme lexigence de la p.i.r.e. applicable au masque dlvation, et nonce la section 6.2.2 3), doivent tre clairement indiqus. De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Canadian ICES-003 Statement This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Radio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Innovation, Science and Economic Development Canada (ISED) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure conditions. (Antennas are greater than 20cm from a person's body). Informations concernant l'exposition aux frquences radio (RF) La puissance de sortie rayonne de l'appareil sans fil est infrieure aux limites d'exposition aux radiofrquences d'Innovation, Sciences et Dveloppement conomique Canada (ISDE). L'Appareil sans fil doit tre utilis de telle manire que le potentiel de contact humain pendant le fonctionnement normal soit minimis. Cet appareil a galement t valu et dmontr conforme aux limites d'exposition RF IC dans des conditions d'exposition mobile. (Les antennes sont plus de 20 cm du corps d'une personne). The County Code Selection feature is disabled for products marketed in the US/Canada. La fonction de slection du code de pays est dsactive pour les produits distribus aux tats-Unis ou au Canada. CAN CPU Module 2 Contains IC ID: 20263-LB1YM EU This product is in compliance with the essential requirements of Council Directive 2014/53/EU on Radio Equipment (RED). UK UKCA (U.K. Conformity Assessed):This product complies with the requirements of U.K. legislation of Radio Equipment Regulations (S.I. 2017/1206).

EN SimPad PLUS 2

Link Box PLUS Important Product Information www.laerdal.com English SimPad PLUS 2 / Link Box PLUS - Regulatory Information Read these instructions thoroughly before connecting the equipment to the power source. Observe all warnings, precautions and instructions on the SimPad PLUS 2, in the User Guide and in this Important Product Information booklet. Retain this booklet for future reference. Warnings and Cautions A Warning states a condition, hazard, or unsafe practice that can result in serious personal injury or death. A Caution states a condition, hazard, or unsafe practice that can result in minor personal injury or damage to the product. Note A note states important information about the product or its operation. Operating Conditions Water and Moisture Cautions Do not operate the device under or near water - for example near a bathtub, kitchen sink, or laundry tub, in a wet basement, near a swimming pool or in other areas with high humidity. Never install jacks for communication cables in wet locations. Do not operate the product with wet hands. Lightning Warning Never use this device, or connect/disconnect communication cables or power cables during lightning storms. Dust Caution Do not operate the device in areas with a high concentration of dust. Cleaning and Maintenance Cleaning Unplug the device from communication lines, mains power outlet or any power source before cleaning or polishing. Do not use liquid cleaners or aerosol cleaners. Use a lint-free cloth lightly moistened with water for cleaning the exterior of the device. Servicing Refer all servicing to qualified service personnel. Warning Do not attempt to service the device yourself. Opening or removing covers may expose you to dangerous voltages or other hazards, and will void the warranty. English SimPad PLUS 2 / Link Box PLUS - Regulatory Information WiFi Connections Please ensure that your settings of the device adhere to any regional restrictions on the use of WiFi channels. Channels 12 and 13 will not work on both the SimPad PLUS 2 and the Link Box PLUS. Accessories Use only accessories specified by the Do not use the RJ-45 as a telephone manufacturer or sold with the apparatus. line connection. Cautions PLUS 2. Use only the SimPad battery with SimPad Do not expose to high temperatures, such as in direct sunlight or in a car parked in the sun. Only charge SimPad PLUS 2 using the supplied battery charger or a recommended charging device that can charge the battery. Dispose of used battery pack promptly and according to local legislations. Do not dispose of in water. Internal Battery Pack in SimPad PLUS 2 Warnings Do not disassemble, crush, puncture, or short external contacts and do not allow metal objects to come into contact with the battery terminals. Do not try to repair the battery; it may cause an explosion. Do not incinerate or dispose of in fire, the battery may explode or release toxic materials. Risk of explosion if battery is replaced by an incorrect type. If the internal battery pack in SimPad PLUS 2 is mishandled, it can burst, cause a fire or even chemical burns. Power Connection and Hazardous Voltage Warnings The product or its accessories may have a hazardous voltage inside. Always power the product from an earthed power outlet. If the provided plug does not fit into your outlet, consult an electrician. Cautions Never attempt to open this product, or any peripherals connected to it, if this action requires a tool. If any parts of the product have visual damage, never attempt to connect main power, or any other power source, before consulting service personnel. Route the power cord to avoid it being walked on or pinched by items placed upon or against it. Pay particular attention to the plugs, receptacles and the point where the cord exits from the device. Do not tug the power cord. English SimPad PLUS 2 / Link Box PLUS - Regulatory Information US Federal Communications Commission (FCC) Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving Increase the separation between the Consult the dealer or an experienced antenna. equipment and receiver. radio/TV technician for help. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. SimPad PLUS 2 Contains FCC ID: QHQ-LB1YM Link Box PLUS Contains FCC ID: QHQ-LB1YM Cautions This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. The use of shielded I/O cables is required when connecting this equipment to any and all optional peripheral or host devices. Failure to do so may violate FCC rules. For Portable Device Usage

(<20cm from body/Specific Absorption Rate (SAR) needed)) Radiation Exposure Statement:

This device meets the governments requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the FCC of the U.S. Government. The exposure standard for wireless device employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands. English SimPad PLUS 2 / Link Box PLUS - Regulatory Information For Country Code Selection Usage

(WLAN Devices) Notes The country code selection is for non-US models only and is not available to all US models. Per FCC regulation, all WiFi products marketed in US must be fixed to US operation channels only. Changes or modifications not covered in this manual must be approved in writing by the manufacturers Regulatory Engineering Department. Changes or modifications made without written approval may void the users authority to operate this equipment. Canada Industry Canada Rules This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Devel-

opment Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Cautions for WLAN 5GHZ Device:

The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit. The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate. The worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in Section 6.2.2(3) shall be clearly indicated. Users should also be advised that high-

power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement:

Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux. Le gain maximal dantenne permis pour les dispositifs utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer la limite de p.i.r.e. Le gain maximal dantenne permis (pour les dispositifs utilisant la bande 5725-5850 MHz) doit se conformer la limite de p.i.r.e. spcifie pour lexploitation point point et non point point, selon le cas. English SimPad PLUS 2 / Link Box PLUS - Regulatory Information Les pires angles dinclinaison ncessaires pour rester conforme lexigence de la p.i.r.e. applicable au masque dlvation, et nonce la section 6.2.2 3), doivent tre clairement indiqus. De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Canadian ICES-003 Statement This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. SimPad PLUS 2 Contains IC ID: 20263-LB1YM Link Box PLUS Contains IC ID: 20263-LB1YM EU This product is in compliance with the essential requirements of Council Directive 2014/53/EU on Radio Equipment (RED). UK UKCA (U.K. Conformity Assessed):This product complies with the requirements of U.K. legislation of Radio Equipment Regulations (S.I. 2017/1206). Radio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Innovation, Science and Economic Development Canada (ISED) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. This device has been evaluated for and shown compliant with the ISED Specific Absorption Rate (SAR) limits when operated in portable exposure conditions. (Antennas are greater than 5mm from a person's body). Informations concernant l'exposition aux frquences radio

(RF) La puissance de sortie rayonne de l'appareil sans fil est infrieure aux limites d'exposition aux radiofrquences d'Innovation, Sciences et Dveloppement conomique Canada (ISDE). L'Appareil sans fil doit tre utilis de telle manire que le potentiel de contact humain pendant le fonctionnement normal soit minimis. Cet appareil a t valu et dmontr conforme aux limites de dbit d'absorption spcifique (SAR) ISDE lorsqu'il est utilis dans des conditions d'exposition portables. (Les antennes sont plus de 5 mm du corps d'une personne). The County Code Selection feature is disabled for products marketed in the US/Canada. La fonction de slection du code de pays est dsactive pour les produits distribus aux tats-Unis ou au Canada. English SimPad PLUS 2 / Link Box PLUS - Regulatory Information Symbol Glossary CE Mark UKCA Mark Li-Ion batteries recycling logo Waste of Electronic and Electrical Equipment Mark Australia RCM Mark UL Listing Mark FCC Declaration of Conformity label Korea Certification Mark Japanese MIC Certification Mark China Compulsory Certification Mark Japanese Voluntary Control Council for Interference by Information Technology Equipment Mark Alert symbol for a Class 2 radio apparatus which employs a frequency band that is not harmonised throughout the European Community and/or that potential restrictions on the use of the apparatus exist in one or more member states. Serial number Warning/Caution Safety SimPad PLUS 2 has IP32 protection rating as defined by standard IEC 60529. Link Box PLUS has IP30 protection rating as defined by standard IEC 60529. WEEE This appliance is marked according to the European directive 2012/19/EC on Waste Electrical and Electronic Equipment

(WEEE). By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Disposal must be carried out in accordance with local environmental regulations for waste disposal. For more detailed information about treatment, recovery and recycling of this product, please contact your local city office, your household waste disposal service or Laerdal representative. Warranty Refer to the Laerdal Global Warranty for terms and conditions. For more information visit www.laerdal.com. English SimPad PLUS 2 / Link Box PLUS - Regulatory Information SimPad PLUS 2 Specifications Operating temperature Storage temperature Size Operating Altitude Weight LCD display Battery type Battery time Battery charging Charging time Communication 0 C to 40 C (32 F to 104 F), Humidity 5 to 90% RH non-

condensing

-20 C to 60 C (-4 F to 140 F) 158 x 126 x 25 mm (6.22 x 4.96 x 0.98 in) 3500 m Maximum 450 g (1lb) High Resolution Color LCD display, 5.7 in, 480 x 640 pixels Li-Ion 3.8 V, capacity: 16 Wh 3 - 4 hours continuous use with 50% display brightness DC input 12V 0.7A max. USB OTG input, 5V 500 mA max 10 80%, approximately 50% / hour from DC input 80% - 100%, 1 hour WiFi 802.11 a/b/g/n/ac Bluetooth SimPad PLUS 2 Connections DC input Ethernet USB Audio Link Box PLUS Operating temperature Size Operating Altitude Weight Communication 12V DC, 3.33 A minimum. (for power adapter*), or 7.2V DC, 4.4A (for battery) RJ45 connector, 10 Mbps / 100 Mbps / 1Gbps USB C on the go input/output 3.5 mm audio jack with TRRS input. Microphone on sleeve

(compatible with iPhone headset) 0 C to 40 C (32 F to 104 F), Humidity 5 to 90% RH non-condensing 140 x 90 x 30 mm (5.51 x 3.54 x 1.18 in) 3500 m Maximum 200 g (0.44 lb) WiFi 802.11 a/b/g/n/ac Bluetooth

*This product is intended to be supplied by a Listed Power Adapter. Contact Laerdal for further assistance with purchasing the power source. English SimPad PLUS 2 / Link Box PLUS - Regulatory Information 12V DC, 3.33 A minimum. (for power adapter**), or 7.34V DC, 5.7A (for battery) RJ45 connector, 10 Mbps / 100 Mbps / 1Gbps Connector for future use Power and signals to manikin. Pulse, sounds etc Connector for Laerdal Li-Ion Battery Connector for Laerdal Li-Ion Battery Cuff pressure input: 0 - 300 mm Hg USB A input / output 3.5 mm jack with TRS input. Line in or microphone level 3.5 mm jack with TRS output. Line out level Li-Ion, 4 cells LIC 18650-M29B 7.34 V nominal 5.7 Ah typical 98 x 78 x 29.7 mm (3.86 x 3.07 x 1.11) 280 g (0.6 Ib) approximately Link Box PLUS Connections DC input Ethernet Future Manikin Battery #1 Battery #2 Blood Pressure USB Audio in Audio out Li-Ion Battery Battery type Cell type Voltage Capacity Size Weight Battery Charging Charging voltage input 9 16 V DC Charging method Constant current Charging time:

Charging Indicator Constant Current + Constant Voltage 1.33A typ. 0 - 80%: 30% per hour. 80% - 100%: 1 hour 1. The charging indicator is only active when there is a charging voltage present 2. Charging: Steady yellow light 3. Charged: Light off

** This product is intended to be supplied by a Listed Power Adapter or DC power source, rated 12Vdc, 3.33A minimum,Tma = 35 degree C, and the altitude of operation = 3500m. Contact Laerdal for further assistance with purchasing the power source. 2023 Laerdal Medical AS. All rights reserved. Manufactured in Taiwan for: Laerdal Medical AS P.O. Box 377 Tanke Svilandsgate 30, 4002 Stavanger, Norway T: (+47) 51 51 17 00 www.laerdal.com

[PN] 20-19560 Rev.A Contain FCC ID : GHQLBIYM Contain IC ID : 20263-LB1YM C LK LY [G CMIIT ID: XXXXXXXXXX RCimt- | aerdal Medical AS 20-19560 GBbor-o10s CAMs ptertareeN0OM

a? en Hy pa ine 8 OL O9 OS OF OE Oz OF 001 06 08 OL 09 0S Oy oe oz OL oz o1 00Z 06 Of 0 09 OG Ob of cop ni OMI ne 70 Fs 1 ne mm oo ne rr Ti): ea (a I) 0S OF OF O OL 00 06 plies 0 09 OS Or Of 02 OL Oo > |

Authorization Letter Date:

Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: QHQ-LB1YM To Whom It May Concern:

We, the undersigned, hereby authorize the following person on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by DEKRA Testing and Certification Co., Ltd. on our behalf shall have the same effect as acts of our own. Agent Company name

: DEKRA Testing and Certification Co., Ltd. Address

: No. 26, Hwaya 1st Road., Guishan District, Taoyuan City, 33341, Taiwan Contact Name

: Phoenix Chen Email

: phoenix.chen@dekra.com We are therefore responsible for the contents of the application. Product description

: Communication Module Model No. Brand Sincerely,

: LBEE5XV1YM

: muRata Signature Contact Name: Mari Kaada Job Title: Corporate Director Q&R Email: mari.kaada@laerdal.com DocuSign Envelope ID: 22B27F08-0B03-4044-A299-74FF1BD349DA24.10.2023

Confidential Request Letter Date: November 29, 2023 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for confidentiality FCC ID: QHQ-LB1YM Long-Term Confidentiality Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Schematics Block Diagrams Theory of Operation Bill of Materials/Parts List Tune-up procedure The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Short-Term Confidentiality (STC) Pursuant to DA04-1705 June 15, 2004 of the Commissions public notice, we also request temporary confidential treatment of information accompanying this application as outlined below:

Internal Photos External Photos Justification: __ Users Manual Test Set-up Photos Planned Release Date STC:

If no date is given, __ days from grant date will be used. Sincerely, Signature Contact Name: Mari Kaada Job Title: Corporate Director Q&R Email: mari.kaada@laerdal.com ______________________________________________________________________________________________ Mail address E-mail and Website Office address Telephone Org.no. 979 484 488 Laerdal Medical AS post@laerdal.no Tanke Svilandsgate

+47 51 51 17 00 P.O. Box 377 4002 Stavanger, Norway www.laerdal.com 30 4007, Stavanger, Norway Telefax

+47 51 52 35 57 DocuSign Envelope ID: C8D620AC-DE48-42A3-A32D-20FB0E928CD7

Covered list Attestation Statement Date:

Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: QHQ-LB1YM Laerdal Medical AS certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Signature Contact Name: Mari Kaada Job Title: Corporate Director of Q&A and Regulatory Affairs Email: mari.kaada@laerdal.no DocuSign Envelope ID: 8E3F94EA-071F-4F34-B30E-1ED40DEFCB7D24.10.2023

Covered list Attestation Statement Date:

Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: QHQ-LB1YM Laerdal Medical AS certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing covered equipment. Sincerely, Signature Contact Name: Mari Kaada Job Title: Corporate Director of Q&A and Regulatory Affairs Email: mari.kaada@laerdal.no DocuSign Envelope ID: 7CE83B75-AD6A-48BD-B3E8-A1EC68A4DAF324.10.2023

Permissive Change Request Letter Date: November 24, 2023 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: QHQ-LB1YM Original Grant Date: October 30, 2023 To Whom It May Concern:

We, the undersigned, hereby attest to the fact that we will apply the class II change. The major change filed under this application is:

1. Additional platform added (Product: CAN CPU Module 2, Brand: Laerdal Medical AS, Model: 20-19560). 2. The device in original application was certified with below antennas:

Ant. Supplier Model No. Type Antenna Gain (dBi) BT & WiFi 2.4GHz WiFi 5GHz 0 1 Molex Molex 146153 146187 Dipole Dipole 3.2 3.4 4.25 4.75 This class II change is to add Dipole antennas with higher gain in WLAN 2.4GHz band as the following table. Ant. Brand Name Model No. Type Antenna Gain (dBi) BT & WiFi 2.4GHz WiFi 5GHz 0 1 TE connectivity 2118909-1 TE connectivity 2118909-1 Dipole Dipole 4.3 4.3 4.3 4.3 Should you have any enquires or comments, please have my best attention. Sincerely, Signature Contact Name: Mari Kaada Job Title: Corporate Director Q&R Email: mari.kaada@laerdal.com DocuSign Envelope ID: A570866B-501D-400B-916C-31F003D648C4

U.S. Agent Authorized Letter Date:

Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Attestation Statements Part 2.911(d)(7) Filing FCC ID: QHQ-LB1YM To Whom It May Concern:

Laerdal Medical AS certifies that, as of the date of the filing of the application, Laerdal Medical Corporation is our designated U.S. agent for service of process for the above referenced FCC ID. Laerdal Medical AS accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Laerdal Medical Corporation accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Sincerely, Applicant:

Company: Laerdal Medical AS FRN: 0007349657 Address: Tanke Svilandsgate 30, Stavanger, Norway, 4002 Contact Name: Mari Kaada Title: Title: Corporate Director Q&R U.S. Agent:

Company: Laerdal Medical Corporation FRN: 0033964867 Address: 167 Myers Corners Rd, Wapppingers Falls, New York, United States, 12590 Contact Name: Donald Garrison Title: QA/RA Manager Tel.: +4751511700 Email: mari.kaada@laerdal.com

(Signature) Tel.: (845) 297-7770 Email: don.garrison@laerdal.com

(Signature) DocuSign Envelope ID: F6AC8705-C8CD-4F32-8DD6-4A711459769124.10.202324.10.2023

Declaration Letter of Change in ID October 23, 2023 Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 We Murata Manufacturing Co., Ltd. agree to give the permission to file a Change in ID for the following FCC ID. Model No.: LBEE5XV1YM FCC ID: VPYLB1YM Approval Date: January 19,2021 Brand Name: Murata Manufacturing Co., Ltd. For a new FCC ID application as below. Company Name: Laerdal Medical AS Model No.: LBEE5XV1YM FCC ID: QHQ- LB1YM There is no change in the design, circuitry, or construction with the aforementioned communication module, and the documents on file with FCC from the original certification remain unchanged and continue to be valid. The new application has its own brand name and FCC ID number. Murata accepts for FCC officials to use the documents on file from the existing certification in processing of applicants FCC ID. Sincerely, Kenji Hayashikoshi Senior Manager Murata Manufacturing Co., Ltd.

Request for Change in Identification Date:

Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for a Change in Identification per Section 2.933 of the FCC Rules Reference: FCC ID: QHQ-LB1YM To whom it may concern:

This change in identification request applies for a new FCC ID as established in 47 CFR 2.933(b) for a currently approved device. This application by Laerdal Medical AS will establish a new FCC ID under Laerdal Medical AS grantee code for the purpose of marketing. The original grant to Murata Manufacturing Co., Ltd. with FCC ID: VPYLB1YM will remain in effect. Per 2.933(b) The original identification is FCC ID: VPYLB1YM. The original granted date is January 19, 2021. The equipment is electrically identical, and there is no change in design, circuitry, or construction of the device. The original test results are applicable and representative of this changed device. External photographs incl. FCC ID label location info are included in this application. The following files are electronically submitted as attachments:

Cover Letter External Photos ID Label and Location Info User Manual Sincerely, Signature Contact Name: Mari Kaada Job Title: Corporate Director Q&R Email: mari.kaada@laerdal.com DocuSign Envelope ID: 7B46404F-ABFE-44C2-8526-04D19CFF3AB224.10.2023