FCC ID: R7PEG1R1X8 Electricity Meter Module

Gridstream RF, Series 5, I210+c Project FCC and IC Compliance Manual Landis+Gyr 2020 | Proprietary + Confidential Rev AA Limitation on Warranties and Liability Information in this document is subject to change without notice. This manual or any part of it thereof may not be reproduced in any form unless permitted by contract or by written permission of Landis+Gyr. In no event will Landis+Gyr be liable for any incidental, indirect, special, or consequential damages

(including lost profits) arising out of or relating to this publication or the information contained in it, even if Landis+Gyr has been advised, knew, or should have known of the possibility of such damages. Covered by both issued and pending patents. For further patent information see: https://www.landisgyr.com/about/patent-notices/

2020 Landis+Gyr, Inc. | Proprietary + Confidential Contact Us:

To provide feedback about this document, email us at ustechnicaldocumentation@landisgyr.com Technical Support: 1-888-390-5733 | solutionsupport.na@landisgyr.com 2 Gridstream RF, Series 5, I210+c Integration Manual Introduction Gridstream RF, Series 5, I210+c is the model name for the Landisgyr+Gyr communication module designed for the Aclara I-210+c meter. The module will be referred to as I210+c module in this document for short. The I210+c module contains two radios, a Zigbee radio and a Sub-GHz radio. The Zigbee radio on the I210+c module is certified for modular approval. The Sub-GHz radio is the S5-MCMO module. This radio complies with modular approval by itself and has its own FCC and IC IDs. The S5-MCM0 is compatible with Landis+Gyr Gridstream RF, Series 5 radios, operating in the unlicensed sub-GHz frequency range of 902 928 MHz. The S5-MCM0 module comes as a component on reel, conforming the LGA surface mount package, and is intended to be placed on a host board using pick-n-place technologies. Both the Zigbee and the Sub-GHz radios are RF shielded metal shields as shown in the pictures below. S5-MCM0 Zigbee Figure 1. I210+c module, top side with shield lids removed S5-MCM0 Zigbee Figure 2. I210+c module, top side with shield lids installed Figure 3. I210+c module, backside PCB F trace antenna is designed as part of the I210+c host board for the Zigbee and SM-

MCM0 radios, see the picture below. Refer to the 24-2468 PCB design file for the specific dimensional details. Each transmitter is certified with the intended trace antenna on the host board. Zigbee Antenna S5-MCM0 Antenna Figure 4. Antennas The I210+c module is designed to be mounted inside of the Aclara I-210+c meter forms specified in the table below, as final host. The module is mount inside of the meter as shown in the picture below. See Aclara 119379-INS document for interface specifications. 4 Figure 5. I210+c module installation view Figure 6. I-210+c meter, final host for the communication module Host and Radio Characteristics The table below contains information on the final host and the radios. Category Specification Value or Range Form Voltage Class Compatible Meters Supported Meter Forms 1S 2S 3S 4S 12S 25S 120V 240V 240V 120V 240V 240V 120V 240V 120V 240V 100A 200A 320A 20A 20A 200A 320A 200A 320A Electrical Voltage As listed above 20%

Typical Burden (Rx at nominal voltage) Less than 3.0 VA 900 MHz Radio

(S5-MCM0) RF ZigBee Environmental Output Power Transmit Frequency

+27 dBm (500 mW) Max 902.2 - 927.8MHz Communication Protocol Frequency Hopping Spread Spectrum Receive Sensitivity Data Rates Modulation Output Power Transmit Frequency Communication Protocol Receive Sensitivity

-103 dBm to - 113 dBm (9.6 kbps to 115.2 kbps) 9.6 - 115.2 kbps 2-FSK and 2-GFSK

+20 dBm Max 2405-2475 MHz ZigBee Protocol

-104 dBm typical Operating Temperature Range

-40 to +85C (under cover) Humidity 95% relative humidity, non-condensing Table 1. Host and radio characteristics 6 Federal Communications Commission (FCC) Compliance Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Consult Landis+Gyr or an experienced radio technician for help. WARNING: Changes or modifications to this device not expressly approved by Landis+Gyr could void the users authority to operate the equipment. Industry Canada (IC) Compliance Notice This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil e doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage adiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. RF Exposure This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Cet quipement est conforme aux limites FCC d'exposition aux radiations dfinies pour un environnement non contrl. Cet quipement doit tre install et utilis une distance minimale de 20cm entre le radiateur et votre corps. Cet metteur ne doit pas tre co-

implants ou exploits en conjonction avec une autre antenne ou metteur. FCC and IC Label Requirements Label Requirement for the I210+c Module (host board) There are two transmitters on the I210+c module, the on-board Zigbee radio and the S5-MCM0 module. Both are modular certified. The label requirement is as follow. A label placed on the I210+c module with the following information is required for the S5-

MCMO. This is required because the S5-MCM0 does not come with a FCC/IC label of its own. See location LBL5 in the figure below. The model name is not required. Contains FCC ID: R7PNG0R1S7 Contains IC: 5294A-NG0R1S7 A label with the following information is required for the Zigbee radio. See location LBL4 in the figure below. 8 Model: Gridstream RF, Series 5, I210+c FCC ID: R7PEG1R1X8 IC: 5294A-EG1R1X8 Figure 7. I210+c module FCC/IC labels Label Requirement for the Final Host In the final installation, a label with the following information must be visible on the host. The model name/number is not required. CONTAINS FCC ID: R7PNG0R1S7 CONTAINS IC: 5294A-NG0R1S7 CONTAINS FCC ID: R7PEG1R1X8 CONTAINS IC: 5294A-EG1R1X8 In the case of the Aclara I-210+c meter, the label design is as shown in the figure below. This label will be shipped as part of the I210+c module kit. The label should be placed on the outside of the meter where it will be visible and readable. Figure 8. I-210+c meter label 10

E--<1) ered a || com keel & *O Bhs oe. 2.5 (64.3) _ | L REF eg] SSS |e ee

= one oo bone ao :

MN) (see ecco XOOOOOOC IC: S24-EGIR DB Model: S5-MICMO Contains FCC ID: R7PNGOR1S7 Contains IC: 52844-NGOR1S7 0.06 (|

TOP SIDE LBL2 } 10

October 7, 2021 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Rd. Columbia, MD 21046 Dear Sir or Madam:

I hereby appoint Kirby Munroe at TV SD America to act as our agent in the preparation of an application for equipment authorization of the model Gridstream RF, Series 5, I210+c, containing device FCC ID:

R7PEG1R1X8 to the FCC Rules and Regulations. I certify that all exhibits contained within this filing properly describe the device or system for which authorization is sought. I further certify that appropriate arrangements have been made to assure that production units of this equipment bearing the name and FCC IDENTIFIER listed in this application will continue to comply with the Commission's requirements. I further certify by signature below that no party (per 47 CFR 1.2002(b)) to the application is subject to a denial of Federal benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Sincerely, James L. Stortz Title: Head of Communication Hardware Delivery 30000 Mill Creek Avenue, Suite 100 | Alpharetta, GA 30022 Tel: +1 678 258 1637 | Fax: +1 678 258 1681

CONFIDENTIALITY REQUEST Date: October 7, 2021 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen:

Landis+Gyr Technology, Inc. respectfully requests confidentiality of certain materials provided with the submission of the model Gridstream RF, Series 5, I210+c, containing device FCC ID: R7PEG1R1X8 in accordance with FCC Regulations 0.459. The confidentiality request applies to the System Block Diagram, Schematics, Parts List, and Theory of Operation contained in this filing. The Gridstream RF, Series 5, I210+c has been developed at considerable effort and expense by Landis+Gyr Technology, Inc. These items are considered as Trade Secrets and therefore public access to the proprietary material could possibly result in duplication of equipment that could severely damage the company's business advantage. I appreciate your assistance in this matter. Sincerely, James L. Stortz Title: Head of Communication Hardware Delivery 30000 Mill Creek Avenue, Suite 100 | Alpharetta, GA 30022 Tel: +1 678 258 1637 | Fax: +1 678 258 1681

To:

From:

Subject:

October 28, 2021 File James L. Stortz Gridstream RF, Series 5, I210+C, FCC ID: R7PEG1R1X8 Modular Approval Request Scope 47CFR 15.212 communicates requirements for products requesting modular approval. In particular, eight requirements are enumerated along with a request that each of the eight be explained for any product requesting such approval. It is the purpose of this document to respond to those eight requirements in regard to the Landis+Gyr product: Gridstream RF, Series 5, I210+C. Modular Approval Requirements 1.1 RF Shielding The Gridstream RF, Series 5, I210+C module is self-shielding and is not dependent on any component or characteristic of the device into which it is embedded. Shielding is accomplished through a combination of metallic self-shielding components, copper planes, guards, and vias in the PCB. The result is a design that has been proven to be neither sensitive to outside influence nor capable of introducing interference into outside components. 1.2 Buffered Modulation / Data Inputs The Gridstream RF, Series 5, I210+C module does not have external modulation or data inputs. Rather, the RF sections are driven by an on-board microprocessor which directly controls the RF data lines and operates so as to not allow excessive modulation. 1.3 Power Supply Regulation The Gridstream RF, Series 5, I210+C module uses linear, low-dropout regulators to provide all the electronics with a supply that is fixed, even when the input voltage is varied. 1.4 Antenna Requirement The Gridstream RF, Series 5, I210+C module comes with a planar inverted-F antenna (PIFA) printed on the board. 1.5 Stand-Alone Testing All testing on the Gridstream RF, Series 5, I210+C module was conducted standalone, or just the board by itself. No shields or enclosures were used, other than those fully integrated into the modules themselves. No ferrites were used on data or power lines during testing. These devices are DC powered, and exceed applicable conducted emission requirements. 1.6 Labeling There are two transmitters on the module, the on-board Zigbee radio (Gridstream RF, Series 5, I210+c) and the S5-MCM0 module. Both are modular certified. The label requirement is as follow. A label with the following information is required for the Zigbee radio. Model: Gridstream RF, Series 5, I210+c FCC ID: R7PEG1R1X8 IC: 5294A-EG1R1X8. A label placed on the module with the following information is required for the S5-MCMO. This is required because the S5-MCM0 does not come with a FCC/IC label of its own. Contains FCC ID: R7PNG0R1S7 Contains IC: 5294A-NG0R1S7 In addition, devices into which they are placed will have labels indicating that this module is contained within. Exact text will be as specified in 47CFR 15.212. 1.7 Specific Rules and Operating Requirements The Gridstream RF, Series 5, I210+C module complies with all pertinent rules for its section. 30000 Mill Creek Avenue, Suite 100 | Alpharetta, GA 30022 Tel: +1 678 258 1637 | Fax: +1 678 258 1681 1.8 RF Exposure Requirements The Gridstream RF, Series 5, I210+C module complies with all exposure requirements. As a component used in the Utility industry, this product is not intended for use near human operators. 2.0 In Reference to 15.212(b) The Gridstream RF, Series 5, I210+C module is always professionally installed and is not sold to the general public. This module undergoes continuous, rigorous testing to ensure that full compliance is always maintained. Sincerely, James L. Stortz Title: Head of Communication Hardware Delivery 30000 Mill Creek Avenue, Suite 100 | Alpharetta, GA 30022 Tel: +1 678 258 1637 | Fax: +1 678 258 1681