FCC ID: R7PMGBM2B1 Series-6 Gen-2 MCM0

D8051 Draft Data Sheet Series-6 Gen-2 MCM0.docx Rev AA D8051 Draft 08.12.2023 Series-6 Gen-2 MCM0 Data Sheet Friday, December 08, 2023 Landis+Gyr D8051 Draft Data Sheet Series-6 Gen-2 MCM0.docx Rev AA D8051 Limitation on Warranties and Liability Information in this document is subject to change without notice. This manual or any part of it thereof may not be reproduced in any form unless permitted by contract or by written permission of Landis+Gyr. In no event will Landis+Gyr be liable for any incidental, indirect, special, or consequential damages (including lost profits) arising out of or relating to this publication or the information contained in it, even if Landis+Gyr has been advised, knew, or should have known of the possibility of such damages. Covered by both issued and pending patents. For further patent information see: https://www.landisgyr.com/about/patent-notices/

2022 Landis+Gyr, Inc. | Proprietary + Confidential Contact Us:

To provide feedback about this document, email us at ustechnicaldocumentation@landisgyr.com Customer Support: 1-888-390-5733 | support.na@landisgyr.com D8051 Rev AA | Series-6 Gen-2 MCM0 (S6G2-MCM0) Data Sheet | Release Date Pending Friday, December 08, 2023 Landis+Gyr D8051 Draft Data Sheet Series-6 Gen-2 MCM0.docx Rev AA D8051 Introduction Landis+Gyr's Series-6 Gen-2 MCM0 (S6G2-MCM0) is key to building a single, integrated IoT network for your utility future. This product is a fully functional Network Interface Card (NIC) in a multi-chip module form-factor to enable low-

cost network and sensor device integration. This technology is foundational to Landis+Gyr's industry-leading utility IoT networking solution, Gridstream Connect. Furthermore, the S6G2-MCM0 provides the flexibility to grow the value of your IoT platform over time with proven Wi-SUN FAN interoperability as you integrate todays and future AMI or DA networking equipment and third-party IoT devices. The device supports RF Mesh (GSP), Mesh IP (SBS) and Wi-SUN

(WSN) FW stacks. Figure 1. Series-6 Gen-2 MCM 0 Table - 1. Technical Specifications Element Radio Model Description Series-6 Gen-2 MCM0 Communication Protocol (PHY) IEEE 802.15.4-2020 MAC/PHY Features MAC PHY Hardware Capabilities RF Modulation RF Bands Automatic selection of best Band based on Link Quality Automatic selection of best Modulation based on Link Quality Adaptive Power Control Precision Output Power Management Clear Channel Assessment IEEE 802.15.4 SUN FSK & OFDM 902 928 MHz Friday, December 08, 2023 Landis+Gyr D8051 Draft Data Sheet Series-6 Gen-2 MCM0.docx Rev AA D8051 Table - 1. Technical Specifications (Continued) Element RF Ports Description 1 Table - 2. Sub-GHz Band Characteristics: North America Network Operating Mode RF Mesh IP Series 5 Compatible RF Mesh IP Green Field Wi-SUN Frequency Range (Fc) 902.4 MHz - 927.6 MHz 904 MHz - 926.8 MHz 902.2 MHz 927.8 MHz Channel Width 400 KHz 1200 kHz 200, 400, 800 & 1200 kHz Number of Channels 64 20 129, 64, 31 & 21 Multicast Modulation 2-FSK 50 kbps OFDM Option 1 MCS0

(100 kbps) 2-FSK 50 kbps Unicast Modulation Support 2-FSK: 50 - 200 kbps OFDM Option 3: MCS3

- MCS6 OFDM Option 1: MCS0

- MCS6 2-FSK: 50 - 200 kbps OFDM Option 3: MCS2 -

MCS3 (100 - 200 kbps) OFDM Option 2: MCS3 -

MCS5 (400 - 800 kbps) OFDM Option 1: MCS5 -

MCS6 (1600 - 2400 kbps) Data Rate Coverage 50 kbps - 600 kbps 100 kbps - 2400 kbps 50 kbps - 2400 kbps Transmitter Output Power 10 mW - 631 mW (peak) 10 mW - 200 mW 10 mW - 631 mW (peak) TBD TBD TBD Receiver Sensitivity

(IEEE 802.15.4) Friday, December 08, 2023 Landis+Gyr D8051 Draft Data Sheet Series-6 Gen-2 MCM0.docx Rev AA D8051 S6G2-MCM0 Outline The PCB outline is shown below:

Figure 2. PCB Outline 1 Figure 3. PCB Outline 2 Friday, December 08, 2023 Landis+Gyr D8051 Draft Data Sheet Series-6 Gen-2 MCM0.docx Rev AA D8051 FCC and Industry Canada Compliance FCC ID for Series-6 Gen-2 MCM0: R7PMGBM2B1 ISED for Series-6 Gen-2 MCM0:5294A-MGBM2B1 FCC Class B This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Consult Landis+Gyr or an experienced radio technician for help. WARNING: Changes or modifications to this device not expressly approved by Landis+Gyr could void the users authority to operate the equipment. Friday, December 08, 2023 Landis+Gyr D8051 Draft Data Sheet Series-6 Gen-2 MCM0.docx Rev AA D8051 RF Exposure This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Cet quipement est conforme aux limites FCC/ISED d'exposition aux radiations dfinies pour un environnement non contrl. Cet quipement doit tre install et utilis une distance minimale de20cm entre le radia-teur et votre corps. Cet metteur ne doit pas tre co-implants ou exploits en conjonction avec une autre antenne ou metteur. Requirement for Modular Certification The S6G2-MCM0 is approved for use with the antenna listed below. Antenna types not included in the list below or having higher gain than the maximum indicated for that type, are prohibited for use with this device. Approved Antennas The antenna listed in the following table is approved for use with the device:

Frequency Antenna Type Max Gain (dBi) Referenced Product Impedance (Typical) 902-928 MHz PCB Printed Inverted F Antenna 1.0 E360 50 ohms Dielectric constant: 4.3 +/-0.2 @ 1GHz. Isolation between S6G2-MCM0 & PCB Printed IFA: S6G2-MCM0 RF Port is connected to Host Printed IFA without any RF pad attenuator in between. Procedure for Antenna Design Verification: Below is the list of tests performed to verify Antennas design performance. 1. S-parameters characterization 2. Radiation Pattern Measurement 3. ERP measurement 4. Radiated Sensitivity measurement NOTE: For Antenna Construction & dimensions, kindly refer to Antenna Datasheet. Friday, December 08, 2023 Landis+Gyr D8051 Draft Data Sheet Series-6 Gen-2 MCM0.docx Rev AA D8051 Information on Test Modes and Additional Testing Requirements A diagnostic test mode is available to device integrators that allows control of the transmitter in order to execute FCC 15.247 compliance testing. This mode of operation provides a basic command interface over a dedicated serial port. Further information on how to enable this mode of operation and a description of the command interface is available to device integrators upon request and under NDA. Additional Testing, Part 15 Subpart B Disclaimer The end product with an embedded S6G2-MCM0 may also need to pass the FCC Part 15 unintentional emission testing requirements and be properly authorized per FCC Part 15 Subpart B. Host Label Requirement In the final installation, the following information must be visible:

Contains FCC ID: R7PMGBM2B1 Contains IC: 5294A-MGBM2B1 Sample label shown below:

Figure 4. Example Host Label Friday, December 08, 2023 Landis+Gyr D8051 Draft Data Sheet Series-6 Gen-2 MCM0.docx Rev AA D8051 Industry Canada This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum

(or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. See Approved Antennas on Page 7. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. Le prsent metteur radio (identifier le dispositif par son numro de certification ou son numro de modle s'il fait partie du matriel de catgorie I) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Friday, December 08, 2023 Landis+Gyr

Series-6 Gen-2 MCM0 FCC/IC Label Information Series-6 Gen-2 MCM0 is a modular approved radio module. The label requirement is as follows. For the Series-6 Gen-2 MCM0, the label will be populated with the FCC/IC information below. Model: Series-6 Gen-2 MCM0 FCC ID: R7PMGBM2B1 IC: 5294A-MGBM2B1 Due to size limitations this label is placed on the reel and packaging material containing the module.

Date: August 07, 2023 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Rd. Columbia, MD 21046 Dear Sir or Madam:

I hereby appoint Mr. Raghavendra Kulkarni at TUV Rheinland India Pvt Ltd. to act as our agent in the preparation of an application for equipment authorization of FCC ID: R7PMGBM2B1 to the FCC Rules and Regulations. I certify that all exhibits contained within this filing properly describe the device or system for which authorization is sought. I further certify that appropriate arrangements have been made to assure that production units of this equipment bearing the name and FCC IDENTIFIER listed in this application will continue to comply with the Commission's requirements. I further certify by signature below that no party (per 47 CFR 1.2002(b)) to the application is subject to a denial of Federal benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Sincerely, James L. Stortz Title: Head of Communication Hardware Delivery 30000 Mill Creek Avenue, Suite 100 | Alpharetta, GA 30022 Tel: +1 678 258 1637 | Fax: +1 678 258 1681

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Rd. Columbia, MD 21046 USA August 21, 2023 Ref: Attestation Statements Part 2.911(d)(5)(i) and Part 2.911(d)(5)(ii) Filing Re. KDB 986446 D01 FCC ID: R7PMGBM2B1 Dear Sir or Madam, Landis+Gyr Technology, Inc (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. If you have any questions, please contact us. Sincerely, James L. Stortz Title: Head of Communication Hardware Delivery Landis+Gyr Technology, Inc 30000 Mill Creek Ave, Suite 100, Alpharetta GA 30022 jim.stortz@landisgyr.com

(678) 258 1434 30000 Mill Creek Avenue, Suite 100 | Alpharetta, GA 30022 Tel: +1 678 258 1637 | Fax: +1 678 258 1681

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Rd. Columbia, MD 21046 USA August 21, 2023 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: R7PMGBM2B1 Landis+Gyr Technology, Inc (the applicant) certifies that, as of the date of the filing of the application, Landis+Gyr Technology, Inc is our designated U.S. agent for service of process for the above referenced FCC ID. Landis+Gyr Technology, Inc accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Landis+Gyr Technology, Inc accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information:

Name: Landis+Gyr Technology, Inc Address: 30000 Mill Creek Ave, Suite 100, Alpharetta GA 30022 Contact Person: James L. Stortz Tel.: (678) 258 1434 Email: jim.stortz@landisgyr.com FRN: 0011025368 Sincerely, Landis+Gyr Technology, Inc James L. Stortz Title: Head of Communication Hardware Delivery 30000 Mill Creek Avenue, Suite 100 | Alpharetta, GA 30022 Tel: +1 678 258 1637 | Fax: +1 678 258 1681

CONFIDENTIALITY REQUEST Date: August 07, 2023 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen:

Landis+Gyr Technology, Inc. respectfully requests confidentiality of certain materials provided with the submission of the Series-6 Gen-2 MCM0 under FCC ID: R7PMGBM2B1 in accordance with FCC Regulations 0.459. The confidentiality request applies to the System Block Diagram, Schematics, Parts List, and Theory of Operation contained in this filing. Series-6 Gen-2 MCM0 has been developed at considerable effort and expense by Landis+Gyr Technology, Inc. These items are considered as Trade Secrets and therefore public access to the proprietary material could possibly result in duplication of equipment that could severely damage the company's business advantage. I appreciate your assistance in this matter. Sincerely, James L. Stortz Title: Head of Communication Hardware Delivery 30000 Mill Creek Avenue, Suite 100 | Alpharetta, GA 30022 Tel: +1 678 258 1637 | Fax: +1 678 258 1681

File James L. Stortz Series-6 Gen-2 MCM0, FCC ID: R7PMGBM2B1 Modular Approval Request August 29, 2023 To:

From:

Subject:

Scope 47CFR 15.212 communicates requirements for products requesting modular approval. In particular, eight requirements are enumerated along with a request that each of the eight be explained for any product requesting such approval. It is the purpose of this document to respond to those eight requirements in regard to the Landis+Gyr product: Series-6 Gen-2 MCM0. Modular Approval Requirements 1.1 RF Shielding The Series-6 Gen-2 MCM0 module is self-shielding and is not dependent on any component or characteristic of the device into which it is embedded. Shielding is accomplished through a combination of metallic self-shielding components, copper planes, guards, and vias in the PCB. The result is a design that has been proven to be neither sensitive to outside influence nor capable of introducing interference into outside components. 1.2 Buffered Modulation / Data Inputs The Series-6 Gen-2 MCM0 module does not have external modulation or data inputs. Rather, the RF sections are driven by an on-board microprocessor which directly controls the RF data lines and operates so as to not allow excessive modulation. 1.3 Power Supply Regulation The Series-6 Gen-2 MCM0 module uses linear, low-dropout regulators to provide all the electronics with a supply that is fixed, even when the input voltage is varied. 1.4 Antenna Requirement The Series-6 Gen-2 MCM0 module is does not come with an antenna. It is designed to be integrated with a host board that provides the antenna. 1.5 Stand-Alone Testing All testing on the Series-6 Gen-2 MCM0 module was conducted standalone, on a host board. No shields or enclosures were used, other than those fully integrated into the modules themselves. No ferrites were used on data or power lines during testing. These devices are DC powered, and exceed applicable conducted emission requirements. 1.6 Labeling The Series-6 Gen-2 MCM0 is a small printed-circuit board module that will be supplied on reel. The FCC ID will be on a label placed on the reel. In addition, devices into which they are placed will have labels indicating that this module is contained within. Exact text will be as specified in 47CFR 15.212. 1.7 Specific Rules and Operating Requirements The Series-6 Gen-2 MCM0 module complies with all pertinent rules for its section. 1.8 RF Exposure Requirements The Series-6 Gen-2 MCM0 module complies with all exposure requirements. As a component used in the Utility industry, this product is not intended for use near human operators. 2.0 In Reference to 15.212(b) The Series-6 Gen-2 MCM0 module is always professionally installed and is not sold to the general public. This module undergoes continuous, rigorous testing to ensure that full compliance is always maintained. Sincerely, James L. Stortz Title: Head of Communication Hardware Delivery 30000 Mill Creek Avenue, Suite 100 | Alpharetta, GA 30022 Tel: +1 678 258 1637 | Fax: +1 678 258 1681