FCC ID: R7PNG0R1S4LP Series 6 Gridstream Mobile Radio

Series 6 Gridstream Mobile Radio T1651/T1661 Data Sheet Publication: 98-2844 Rev AA Landis+Gyr 2022 | Proprietary + Confidential Draft 05.10.2022 A Limitation on Warranties and Liability Information in this document is subject to change without notice. This manual or any part of it thereof may not be reproduced in any form unless permitted by contract or by written permission of Landis+Gyr. In no event will Landis+Gyr be liable for any incidental, indirect, special, or consequential damages (including lost profits) arising out of or relating to this publication or the information contained in it, even if Landis+Gyr has been advised, knew, or should have known of the possibility of such damages. Covered by both issued and pending patents. For further patent information see: https://www.landisgyr.com/about/patent-notices/

2022 Landis+Gyr, Inc. | Proprietary + Confidential Contact Us:

To provide feedback about this document, email us at ustechnicaldocumentation@landisgyr.com Customer Support: 1-888-390-5733 | support.na@landisgyr.com 98-2844 Rev AA | Series 6 Gridstream Mobile Radio T1651/T1661 Data Sheet | Pending Draft 05.10.2022 A Series 6 Gridstream Mobile Radio T1651/T1661 Data Sheet Introduction The Gridstream Mobile Radio (GMR) is a field tool device that enables customers to communicate with Mesh IP and Wi-SUN devices. The device uses the standard USB-C serial cable to connect to a user's PC. Two-way communication with the GMR provides the capability to transmit and receive data from AMI endpoints. This product is low power mode capable which helps connect to modules in single channel mode. GMR contains Landis+Gyr's Network Node which is a fully functional, Network Interface Card (NIC) that is mPCIe standard-enabled for simple network and sensor device integration. Figure 1. Series 6 Gridstream Mobile Radio Data Sheet 98-2844 Rev AA | 3 Draft 05.10.2022 A Series 6 Gridstream Mobile Radio T1651/T1661 Data Sheet Table 1. Series 6 GMR T1651 Specification Element Radio Model Description Series 6 GMR T1651 Communication Protocol (PHY) IEEE 802.15.4-2020 MAC/PHY Features MAC PHY Hardware Capabilities Clock Speed RAM Memory FLASH Memory RF Modulation RF Bands RF Port Mechanical Simultaneous multi-band support Automatic selection of 'best' Band based on Link Quality Automatic selection of 'best' Modulation based on Link Quality Adaptive Power Control (i.e., Short range output power back-off) Precision Output Power Management Clear Channel Assessment 120 MHz 640 KB 2 MB + 4 MB External IEEE 802.15.4 SUN FSK, O-QPSK & OFDM Sub-GHz & 2.4-GHz Simultaneous Operation Single 50 U.FL Male Connector Operating Temperature

-20 to 65C IP Rating IP53 (when rubber plug is closed) Sub-GHz Band Characteristics: North America, Mexico & Brazil Network Operating Mode Series 5 Compatible Greenfield Frequency Range (Fc) USA/Canada/Mexico: 902.4 - 927.6 MHz 902.4 MHz 926.8 MHz Brazil: 902 - 907.5 MH, 915 - 928 MHz N/A Channel Width Number of Channels 400 KHz 64 1200 kHz 20 Multicast Modulation 2-FSK 50 kbps OFDM Option 1 MCS0 (100 kbps) Data Rate Coverage 50 kbps - 600 kbps 100 kbps - 2400 kbps Transmitter Power 50 mW - 800 mW 10 mW - 427 mW (average) Transmitter Low Power 400 W (peak) N/A Receiver Sensitivity

(IEEE 802.15.4) F2B50 = -108 dBm F2B150 = -100 dBm F2B200 = -99 dBm O3M3 = -107 dBm O3M4 = -105 dBm O3M5 = -102 dBm O3M6 = -97 dBm O1M0 = -110 dBm O1M1 = -109 dBm O1M2 = -105 dBm O1M3 = -102 dBm O1M4 = -99 dBm O1M5 = -96 dBm O1M6 = -90 dBm Sub-GHz Band Characteristics: Philippines Network Operating Mode Series 5 Compatible 4 | 98-2844 Rev AA Data Sheet Draft 05.10.2022 A Table 1. Series 6 GMR T1651 Specification (Continued) Series 6 Gridstream Mobile Radio T1651/T1661 Data Sheet Element Description Frequency Range (Fc) 915.2 MHz - 917.6 MHz Channel Width Number of Channels 400 KHz 7 SUN Modulation Support 2-FSK: 50 - 200 kbps OFDM Option 3: MCS3 - MCS6 Data Rate Coverage 50 kbps 150 kbps Transmitter Power 50 mW - 800 mW Receiver Sensitivity

(IEEE 802.15.4) F2B50 = -108 dBm F2B150 = -100 dBm F2B200 = -99 dBm O3M3 = -107 dBm O3M4 = -105 dBm O3M5 = -102 dBm O3M6 = -97 dBm Sub-GHz Band Characteristics: Hong Kong & Bangladesh Network Operating Mode Series 5 Compatible Frequency Range (Fc) 920.6 MHz - 924.6 MHz Channel Width Number of Channels 400 KHz 11 SUN Modulation Support 2-FSK: 50 - 200 kbps Data Rate Coverage 50 kbps 200 kbps Transmitter Power 50 mW - 800 mW Receiver Sensitivity

(IEEE 802.15.4) F2B50 = -108 dBm F2B150 = -100 dBm F2B200 = -99 dBm Sub-GHz Band Characteristics: Australia Network Operating Mode Series 5 Compatible Frequency Range (Fc) 915.6 MHz - 927.6 MHz Channel Width Number of Channels 400 KHz 31 SUN Modulation Support 2-FSK: 50 - 200 kbps Data Rate Coverage 50 kbps 200 kbps Transmitter Power 50 mW - 800 mW Receiver Sensitivity

(IEEE 802.15.4) Sub-GHz Band Characteristics: International F2B50 = -108 dBm F2B150 = -100 dBm F2B200 = -99 dBm O3M3 = -107 dBm O3M4 = -105 dBm O3M5 = -102 dBm O3M6 = -97 dBm Data Sheet 98-2844 Rev AA | 5 Draft 05.10.2022 A Series 6 Gridstream Mobile Radio T1651/T1661 Data Sheet Table 1. Series 6 GMR T1651 Specification (Continued) Element Description Network Operating Mode 2.4-GHz Frequency Range (Fc) 2410.8 MHz to 2461.2 MHz Channel Width Number of Channels 1200 KHz 43 Multicast Modulation OFDM Option 1 MCS0 (100 kbps) Unicast Modulation Support OFDM Option 1: MCS0 - MCS6 Data Rate Coverage 100 kbps - 2400 kbps Transmitter Power 100 mW - 490 mW (average) Receiver Sensitivity

(IEEE 802.15.4) O1M0 = -112 dBm O1M1 = -111 dBm O1M2 = -107 dBm O1M3 = -105 dBm O1M4 = -102 dBm O1M5 = -99 dBm O1M6 = -93 dBm 6 | 98-2844 Rev AA Data Sheet Draft 05.10.2022 A Series 6 Gridstream Mobile Radio T1651/T1661 Data Sheet Table 2. Series 6 GMR T1661 Specification Communication Protocol (PHY) 802.15.4-2015 Description Series 6 GMR T1661 Automatic selection of 'best' Modulation based on Link Quality Adaptive Power Control (i.e., Short range output power back-off) Precision Output Power Management Clear Channel Assessment Element Radio Model MAC/PHY Features MAC PHY Hardware Capabilities Clock Speed RAM Memory FLASH Memory RF Modulation RF Bands RF Port 120 MHz 640 KB Sub-GHz 2 MB + 4 MB External IEEE 802.15.4 SUN FSK, O-QPSK & OFDM Internal Multi-Band 1dBi Antenna Sub-GHz Band Characteristics: North America Network Operating Mode Wi-SUN Frequency Range (Fc) 902.2 MHz 927.8 MHz Channel Width Number of Channels Multicast Modulation 200, 400, 800 & 1200 kHz 129, 64 31 & 21 2-FSK 50 kbps Unicast Modulation Support 2-FSK: 50 - 200 kbps OFDM Option 3: MCS2 - MCS3 (100 - 200 kbps) OFDM Option 2: MCS3 - MCS5 (400 - 800 kbps) OFDM Option 1: MCS5 - MCS6 (1600 - 2400 kbps) Data Rate Coverage 50 kbps - 2400 kbps Transmitter Output Power 50 mW - 800 mW Receiver Sensitivity

(10% PER, conducted) F2B50 = -108 dBm F2B150 = -100 dBm F2B200 = -99 dBm O3M2 = -109 dBm O3M3 = -107 dBm O2M3 = -106 dBm O2M4 = -104 dBm O2M5 = -101 dBm O1M5 = -96 dBm O1M6 = -90 dBm Data Sheet 98-2844 Rev AA | 7 Draft 05.10.2022 A Series 6 Gridstream Mobile Radio T1651/T1661 Data Sheet FCC, Industry Canada Compliance FCC Class B This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Consult Landis+Gyr or an experienced radio technician for help. WARNING: Changes or modifications to this device not expressly approved by Landis+Gyr could void the users authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet quipement est conforme aux limites d'exposition aux radiations FCC dfinies pour un environnement non contrl. Cet quipement doit tre install et utilis une distance minimale de 20 cm entre le radiateur et votre corps. Cet metteur ne doit pas tre situ proximit ou fonctionner en conjonction avec toute autre antenne ou metteur. RF Exposure 8 | 98-2844 Rev AA Data Sheet Draft 05.10.2022 A Series 6 Gridstream Mobile Radio T1651/T1661 Data Sheet Industry Canada This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. NOTE: The GMR uses an internal antenna that complies with aforementioned requirements. There is no provision to use an external antenna. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. Le prsent metteur radio (5294A-NG0R1S4LP) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Regulatory Compliance Brazil Anatel Model: T1651 ANATEL ID: TBA Este equipamento no tem direito proteo contra interferncia prejudicial e no pode causar interferncia em sistemas devidamente autorizados. Data Sheet 98-2844 Rev AA | 9 Draft 05.10.2022 A Series 6 Gridstream Mobile Radio T1651/T1661 Data Sheet Regulatory Compliance Mexico and Philippines IFETEL Regulatory blurb will be updated after regulatory certification is obtained. Regulatory Compliance Bangladesh BTRC Guidelines This device complies with BTRC guidelines. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Regulatory Compliance Hong Kong This device complies with the HKCA1049 (Issue 1) performance specification issued by the Communications Authority under the Scheme on Certification of Telecommunications Equipment and Industrial, Scientific and Medical (ISM) Equipment by the Local Certification Bodies (LCB Scheme). Regulatory Compliance Australia Regulatory blurb will be updated after regulatory certification is obtained. 10 | 98-2844 Rev AA Data Sheet Draft 05.10.2022 A

Figure 1: Sample Label Label is populated as follows:

8 FCC ID: R7PNG0R1S4LP IC: 5294A- NG0R1S4LP 9 T1651 or T1661 Label Goes Here Figure 2: Label Location

May 12, 2022 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Rd. Columbia, MD 21046 Dear Sir or Madam:

I hereby appoint Kirby Munroe at TV SD America to act as our agent in the preparation of an application for equipment authorization of FCC ID: R7PNG0R1S4LP to the FCC Rules and Regulations. I certify that all exhibits contained within this filing properly describe the device or system for which authorization is sought. I further certify that appropriate arrangements have been made to assure that production units of this equipment bearing the name and FCC IDENTIFIER listed in this application will continue to comply with the Commission's requirements. I further certify by signature below that no party (per 47 CFR 1.2002(b)) to the application is subject to a denial of Federal benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Sincerely, James L. Stortz Title: Head of Communication Hardware Delivery 30000 Mill Creek Avenue, Suite 100 | Alpharetta, GA 30022 Tel: +1 678 258 1637 | Fax: +1 678 258 1681

CONFIDENTIALITY REQUEST Date: May 12, 2022 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen:

Landis+Gyr Technology, Inc. respectfully requests confidentiality of certain materials provided with the submission of the Series 6 RF Mesh IP Gridstream Mobile Radio T1651 and Series 6 Wi-SUN Gridstream Mobile Radio T1661 under FCC ID: R7PNG0R1S4LP in accordance with FCC Regulations 0.459. The confidentiality request applies to the System Block Diagram, Schematics, Parts List, and Theory of Operation contained in this filing. Series 6 RF Mesh IP Gridstream Mobile Radio T1651 and Series 6 Wi-SUN Gridstream Mobile Radio T1661 have been developed at considerable effort and expense by Landis+Gyr Technology, Inc. These items are considered as Trade Secrets and therefore public access to the proprietary material could possibly result in duplication of equipment that could severely damage the company's business advantage. I appreciate your assistance in this matter. Sincerely, James L. Stortz Title: Head of Communication Hardware Delivery 30000 Mill Creek Avenue, Suite 100 | Alpharetta, GA 30022 Tel: +1 678 258 1637 | Fax: +1 678 258 1681