FCC ID: DBZSMQV19A Wireless Microphone Transmitter

INSTRUCTION MANUAL SMV Series Super Miniature Variable Power Transmitters With Digital Hybrid Wireless Technology US Patent 7,225,135 SMQV Dual Battery Model SMV Single Battery Model Fill in for your records:

Serial Number:

Purchase Date:

Rio Rancho, NM, USA www.lectrosonics.com Introduction The SM Series variable power transmitters are the product of many years of engineering and experience in professional audio markets. The unique design provides several distinct features for professional applications:

Selectable output power to maximize battery life or operating range as needed Superb, compandor-free audio quality Ultra-lightweight, corrosion resistant housing Water resistant seals for use in damp environments Programmable compatibility modes for use with a wide variety of different receivers The Digital Hybrid Wireless design (US Patent 7,225,135) combines 24-bit digital audio with analog FM resulting in a system that has the same operating range as analog systems, the same spectral efficiency as analog systems, the same long battery life as analog systems, plus the excellent audio fidelity typical of pure digital systems. The SM Series transmitters feature the unique servo bias input circuitry with a standard TA5M type input jack for use with electret lavaliere mics, dynamic mics, or line level signals. A water resistant control panel with LCD, membrane switches and multi-color LEDs make input gain adjustments, frequency and compatibility mode selection quick and accurate, without having to view the receiver. The battery compartment accepts AA lithium or rechargeable batteries. The housings are machined from solid aluminum blocks to provide an extremely lightweight and rugged package. A special non-corrosive finish resists salt water exposure and perspiration in extreme environments. These ETSI compliant transmitters work with Digital Hybrid receivers in the Nu Hybrid mode, with Lectro-

sonics IFB receivers, and in a special Mode 3 for use with receivers from another manufacturer. 2 SMV SeriesLECTROSONICS, INC. Table of Contents Introduction .............................................................................................................................................................................................2 General Technical Description ..............................................................................................................................................................4 Controls and Functions .........................................................................................................................................................................6 LCD Screen ..........................................................................................................................................................................................6 Power LED ............................................................................................................................................................................................6 Power LED Off Feature .........................................................................................................................................................................6 Audio Input Jack ....................................................................................................................................................................................6 Modulation LEDs ...................................................................................................................................................................................6 AUDIO Button .......................................................................................................................................................................................6 FREQ Button .........................................................................................................................................................................................6 Up/Down Arrows ...................................................................................................................................................................................6 Battery and Battery Eliminator Installation ..........................................................................................................................................7 Attaching and Removing the Microphone ............................................................................................................................................7 Operating Instructions ...........................................................................................................................................................................8 Power Up and Boot Sequence ..............................................................................................................................................................8 Power Down ..........................................................................................................................................................................................8 Standby Mode .......................................................................................................................................................................................8 LCD Backlight Settings .........................................................................................................................................................................8 Selecting the Compatibility Mode and Output Power .................................................................................................................................................................................8 Audio Screen ........................................................................................................................................................................................9 Frequency Screen .................................................................................................................................................................................9 Lock/Unlock Screen ..............................................................................................................................................................................9 Remote Control Operation ....................................................................................................................................................................9 Configuring for Power Restore ............................................................................................................................................................10 Setting Transmitter Operating Frequency ............................................................................................................................................10 Set Up in 100 kHz Mode .....................................................................................................................................................................10 Set Up in 25 kHz Mode .......................................................................................................................................................................10 Adjusting Audio Level (Gain) ...............................................................................................................................................................10 Locking or Unlocking the Controls ......................................................................................................................................................11 5-Pin Input Jack Wiring ........................................................................................................................................................................11 Line Level Signals ...............................................................................................................................................................................12 Installing the Connector: .....................................................................................................................................................................12 Microphone RF Bypassing ..................................................................................................................................................................12 Microphone Cable Termination for Non-Lectrosonics Microphones .............................................................................................................................................13 Wiring Hookups for Different Sources ...............................................................................................................................................14 Silver Paste on SM Series Transmitter Thumbscrews .......................................................................................................................15 LectroRM ...............................................................................................................................................................................................16 Straight Whip Antennas .......................................................................................................................................................................17 Accessories for single battery models: ..............................................................................................................................................18 Accessories for dual battery models: .................................................................................................................................................18 Accessories for Both Models ..............................................................................................................................................................19 Troubleshooting ....................................................................................................................................................................................20 Specifications and Features ................................................................................................................................................................22 Service and Repair ...............................................................................................................................................................................23 Returning Units for Repair ..................................................................................................................................................................23 3 Super-Minature Belt Pack TransmitterRio Rancho, NM General Technical Description Servo Bias Input No Pre-Emphasis/De-Emphasis The voltage and current requirements of the wide vari-

ety of electret microphones used in professional appli-

cations has caused confusion and compromises in the wiring needed for wireless transmitters. To address this problem, the unique Servo Bias input circuit provides an automatically regulated voltage over a very wide range of current for compatibility with all microphones. Digital Hybrid Wireless Technology All wireless links suffer from channel noise to some de-

gree, and all wireless microphone systems seek to mini-

mize the impact of that noise on the desired signal. Con-

ventional analog systems use compandors for enhanced dynamic range, at the cost of subtle artifacts (typically pumping and breathing). Wholly digital systems defeat the noise by sending the audio information in digital form, at the cost of some combination of power, bandwidth and resistance to interference. Digital Hybrid systems overcome channel noise in a dramatically new way, digitally encoding the audio in the transmitter and decoding it in the receiver, yet still send-

ing the encoded information via an analog FM wireless link. This proprietary algorithm is not a digital imple-

mentation of an analog compandor but a technique that can be accomplished only in the digital domain, even though the inputs and outputs are analog. Because it uses an analog FM link, the Digital Hybrid system enjoys all the benefits of conventional FM wire-

less systems and it does away with the analog compan-

dor and its artifacts. The Digital Hybrid design results in a signal-to-noise ratio high enough to preclude the need for conventional pre-

emphasis (HF boost) in the transmitter and de-emphasis

(HF roll off) in the receiver. This eliminates the potential for distortion of signals with abundant high-frequency information. Low Frequency Roll-Off The low frequency roll-off can be set for a 3 dB down point at 35, 50, 70, 100, 120 and 150 Hz to control sub-

sonic and very low frequency audio content in the au-

dio. The actual roll-off frequency will vary slightly depend-

ing upon the low frequency response of the microphone. Excessive low frequency content can drive the transmit-

ter into limiting, or in the case of high level sound sys-

tems, can even cause damage to loudspeaker systems. The roll-off is normally adjusted by ear while listening as the system is operating. Input Limiter A DSP-controlled analog audio limiter is employed be-

fore the A-D converter. The limiter has a range of more than 30 dB for excellent overload protection. A dual re-

lease envelope makes the limiter acoustically transpar-

ent while maintaining low distortion. It can be thought of as two limiters in series, a fast attack and release limiter followed by a slow attack and release limiter. The limiter recovers quickly from brief transients, with no audible side effects, and also recovers slowly from sustained high levels to keep audio distortion low while preserving short term dynamics.

+5V 5V Regulator

+6V Variable 1.8 - 4v X1 11.289 MHz 4 X2 12.000 MHz SMV SeriesLECTROSONICS, INC. Signal Encoding and Pilot Tone Variable Power Output This advanced feature allows the operator to optimize the transmitter for maximum battery life, or for maximum operating range. Power output is selected using the LCD in a setup mode while the RF output of the trans-

mitter is turned off. Battery Options and Operating Time Switching power supplies convert regulated battery volt-

ages to operate various circuit stages with maximum efficiency. The firmware remembers the power status when a battery fails, so the transmitter will be turned on auto-

matically when the battery is replaced and the previous settings will be enabled. Circulator/Isolator The RF output circuit includes a one way circulator/iso-

lator using a magnetically polarized ferrite. This device greatly reduces RF intermodulation produced when multiple transmitters are used in close proximity to one another (several feet apart). The isolator also provides additional RF output stage protection against static shock. In addition to controlling the limiter, the DSP also en-

codes the digitized audio from the A/D converter and adds an ultrasonic pilot tone to control the squelch in the receiver. A pilot tone squelch system provides a reli-

able method of keeping a receiver output muted (audio mute) even in the presence of significant interference. When the system is operating in the Nu Hybrid mode, a different pilot tone frequency is generated for each car-

rier frequency to prevent inadvertent squelch problems in multi-channel sytems. Microprocessor Control A microprocessor monitors user command inputs from the control panel buttons and numerous other internal signals. It works intimately with the DSP to ensure the audio is encoded according to the selected Compatibil-

ity Mode and that the correct pilot tone is added to the encoded signal. Compatibility Modes SM Series ETSI compliant transmitters are designed to operate with Lectrosonics Digital Hybrid receivers in Nu Hybrid Mode and will yield the best performance when doing so. However, due to the flexibility of digital signal processing, the transmitters can also operate with Lec-

trosonics IFB receivers and in a special Mode 3 for use with receivers from another manufacturer. Contact the factory for details on this special mode. Control Panel The control panel includes four membrane switches and an LCD screen to adjust the operational settings. Multi-

color LEDs are used to indicate audio signal levels for accurate gain adjustment and for battery status. Wide-Band Deviation 75 kHz deviation improves the signal to noise ratio and audio dynamic range of a wireless system dramatically, compared to other designs that use 30 kHz to 40 kHz deviation. Wide deviation combined with a high powered transmitters makes a significant improvement in signal to noise ratio and operating range. 5 Super-Minature Belt Pack TransmitterRio Rancho, NM Controls and Functions Modulation LEDs Battery Compartment Cover Plate LCD Battery Compartment Thumb Screw UP Arrow Antenna Jack Audio Input Jack DOWN Arrow PWR LED AUDIO Button FREQ Button LCD Screen The LCD is a numeric-type Liquid Crystal Display with screens for adjusting power, frequency, audio level and low frequency audio roll-off. The transmitter can be powered up with or without the RF output turned on. A countdown appears in the LCD when powering on and off, allowing the transmitter to be turned on without RF for adjustments, and to prevent accidentally turning it off with momentary button presses. Power LED The PWR LED glows green when the battery is good. The color changes to red when there is about 30 min-

utes of operation left with the recommended lithium bat-

tery. When the LED begins to blink red, there are only a few minutes of life. The exact point at which the LED turns red will vary with battery brand and condition, temperature and cur-

rent drain. The LED is intended to simply catch your attention, not to be an exact indicator of remaining time. Varies Green Red Blink e g a t l o V 1.6 1.4 1.2 1.0

.8 4 2 Hours 8 A weak battery will sometimes cause the PWR LED to glow green immediately after the transmitter is turned on, but will soon discharge to the point where the LED will turn red or the unit will turn off completely. 6 Power LED Off Feature In normal operating mode, the DOWN and UP Arrow buttons may be used to turn the PWR LED indica-

tors off and on. This setting does not persist through a power cycle nor does it affect the LCD backlight. 6 Audio Input Jack The Servo Bias input circuitry accommodates virtually every lavaliere, handheld or shotgun microphone avail-

able, plus line level signals. Battery Compartment and Thumb Screw The large knurled thumbscrew is used to release or secure the Battery Compartment Cover Plate. Modulation LEDs Proper input gain adjustment is critical to ensure the best audio quality. Two bicolor LEDs will glow either red or green to accurately indicate modulation levels. The input circuitry includes a wide range DSP controlled limiter to prevent distortion at high input levels. It is important to set the gain (audio level) high enough to achieve full modulation during louder peaks in the audio. The limiter can handle over 30 dB of level above full modulation, so with an optimum setting, the LEDs will flash red during use. If the LEDs never flash red, the gain is too low. In the table below, +0 dB indicates full modulation. Signal Level Less than -20 dB

-20 dB to -10 dB

-10 dB to +0 dB

+0 dB to +10 dB Greater than +10 db Off Green Green Red Red Off Off Green Green Red

-20 LED

-10 LED AUDIO Button The AUDIO button is used to display the audio level and low frequency roll-off settings. The UP and DOWN ar-

rows adjust the values. The AUDIO button is also used with the FREQ button to enter standby mode and to power the transmitter on or off. FREQ Button The FREQ Button displays the selected operating frequency and toggles the LCD between displaying the actual operating frequency in MHz and a two-digit hexadecimal number that corresponds to the equivalent Lectrosonics Frequency Switch Setting. Up/Down Arrows The Up and Down arrow buttons are used to select the values on the various setup screens and to lock out the control panel. Antenna The transmitter uses a whip antenna with a flexible wo-

ven, galvanized steel mesh cable and a standard SMA connector. SMV SeriesLECTROSONICS, INC. Battery and Battery Eliminator Installation Note: Standard zinc-carbon batteries marked heavy-duty or long-lasting are not adequate. The battery status circuitry is designed for the voltage drop over the life of lithium batteries. To install new batteries:

1. Turn the Battery Cover Plate Thumbscrew counter-

clockwise a few turns until the door will rotate. 2. Insert the new batteries into the housing. The posi-

tive (+) battery terminal goes into the transmit-

ter first. Attaching and Removing the Microphone The flexible sleeve over the 5-pin plug on the micro-

phone helps prevent dust and moisture from getting into the input jack. The flange around the rim of the connec-

tor on the transmitter helps retain the sleeve after it is installed and The following procedure simplifies the attachment and removal of the microphone to assure the sleeve is seated securely. Align the pins on the plug and jack and insert the con-

nector. 3. Align the Battery Cover Plate and tighten the Bat-

tery Cover Plate Thumbscrew. Gore-Tex covered vent Do Not Cover Vent Polarity engraved into housing Two battery compartments

(SMQV) 1 2 Pinch and squeeze the sleeve on this end to work it down over the flange. NOTE: Refer to the previous section entitled Configuring for Power Restore 3 Release button To install the battery eliminator, loosen the thumbscrew completely and remove the battery door. Insert the battery eliminator and tighten the thumbscrew. Install plastic cap on dual battery model to cover the open battery compartment. If the sleeve is pulled down and covering the connector, squeeze the end of the sleeve so you can feel the connector inside and press it into the jack until it latches. Pinch and squeeze the sleeve near the flange and work it down with a kneading motion over the flange all the way around until it stays in place flush with the housing. Pull on the connector to make sure it is firmly latched. To remove the connec-

tor, pull the sleeve back to expose the black release button. Press the button to unlatch the plug. Gore - Tex Registered trademark of W. L. Gore and Associates 7 Super-Minature Belt Pack TransmitterRio Rancho, NM Operating Instructions Power Up and Boot Sequence 1) Ensure that good batteries are installed in the unit. 2) Simultaneously press and hold the AUDIO and FREQ buttons until the Power On Boot Sequence is initiated. LCD Backlight Settings The LCD backlight can be set to turn off after either 5 minutes or 30 seconds, or stay on continuously. Hold the UP arrow in while powering up the unit to enter the setup screen. Press the AUDIO button repeatedly to step through the setup items to reach the backlight settings screen. Use the UP or DOWN arrow button to select the desired setting. The count will progress from 1 through 3 and the unit will then power up with the RF output turned on. During this turn on sequence, the modulation and power LEDs all glow red, then green, and then revert to normal operation. The LCD displays a bootup sequence which con-

sists of four screens:

Company Name:

Frequency Block (bXX) and Firmware Version (rX.X):

Power Level Compatibility Mode:

Audio:

b21r1.1 (typ) Pr 250 CP 400 (typ) Aud 12 (typ) Lectro Power Down Initial Power Off Timer Screen 1) Simultaneously press and hold the AUDIO and FREQ buttons while observing that the word Off appears in the LCD along with a counter. 2) When the counter reaches 0, the unit turns off. Note: If the AUDIO and FREQ buttons are released before the LCD goes blank at the end of the countdown, the unit will not turn off. Instead, it will stay energized and the display will return to the previous screen. Standby Mode Standby Screen With the power turned off, pressing the AUDIO and FREQ buttons briefly places the unit in Standby Mode. In this mode the RF output is turned off so all setup adjustments can be made without interfering with other systems operating in the same location. The screen displays rf OFF to remind the user that the unit is not transmitting. While the unit is in the standby mode, access the setup screens using the AUDIO and FREQ buttons and make adjustments using the Up and Down arrows. 8 Selecting Step Size mode Hold the UP arrow in while powering up the unit to enter the setup screen. Press the AUDIO button repeatedly to step through the setup items to reach the Step Size Mode screen. Use the UP or DOWN arrow button to select the desired setting. Selecting the Compatibility Mode and Output Power IFB compatibility mode The transmitter will work with Digital Hybrid receivers in the Nu Hybrid mode, Lectrosonics IFB receivers and in a special Mode 3 for use with receivers from another manufacturer. Power setting Note: The unit automatically enters the Standby Mode when selecting compatibility. 1) Set the receivers audio controls to minimum. 2) From a power off condition, hold down the Up arrow, then simultaneously press the AUDIO and FREQ buttons. 3) Press either AUDIO or FREQ button to select the compatibility screen and use the Up and Down ar-

rows to select the desired mode. The following Compatibility Modes are available:

CP 3 Mode 3 (contact the factory for details):

CP Nu Nu Hybrid:

IFB Series mode:

CP IFB 4) Press either AUDIO or FREQ button to select the power setting screen and use the Up and Down down arrows to select the desired level of power. 5) Simultaneously press the AUDIO and FREQ but-

tons to exit this mode and turn off the power. SMV SeriesLECTROSONICS, INC. If a remote control signal is detected but the transmitter is set to rc oFF, the message rc oFF will be dis-

played briefly on the transmitters LCD, to confirm that a valid signal was received, but that the transmitter is not configured to respond to it. Remote functions available are:

Tx Input Gain Sleep/Unsleep Lock/Unlock Frequency Tuning in 25 kHz steps Changing the low frequency roll-off setting Turning on/off the PWR and Audio LEDs Gain up/down functions In sleep mode, the transmitter uses only 20% of the normal amount of battery drain. Sleep mode can only be invoked with the remote control, and can only be revoked with the remote control or by removing the battery. When in the sleep mode, the PWR LED blinks green every few seconds to indicate that the transmitter is asleep and not turned off. NOTE: See LectroRM for more information. Audio Screen The Audio screen is used to adjust input gain from 0 to +44 dB, and the low frequency roll-off from 35 to 150 Hz. Repeatedly pressing the AUDIO button toggles back and forth between the two displays. Press and hold the AUDIO button and use the Up and Down arrows to make adjustments. Frequency Screen The Frequency Screen displays the operating frequency in MHz or as a two-digit hexadecimal number that corresponds to the equivalent Lectrosonics Frequency Switch Setting. Repeatedly pressing the FREQ button toggles between the two displays. Press and hold the FREQ button and use the Up and Down arrows to select the frequency. Lock/Unlock Screen Simultaneously pressing and holding both the Up and Down arrow buttons during normal operation starts the Lock timer. The timer starts at three and counts down to zero. When the timer reaches zero, the transmitters controls are locked. With the controls locked, the AUDIO and FREQ buttons can still be used to display current settings. Any attempt to change a setting by pressing either the Up or Down arrow button will result in an on-screen Loc reminder that the controls are locked. Remove the batteries to unlock the control panel. Important: Once the transmitter is locked, it cannot be unlocked or powered off using the buttons. The only ways to unlock a locked transmitter are to remove the battery or unlock it via the RM remote control. Remote Control Operation The transmitters can be configured to respond to signals from the LectroRM app or to ignore them. This setting is accessed by holding Down arrow button while powering the transmit-

ter on. Use the arrow keys to Remote Control Screens toggle between rc on (remote control on) and rc oFF (remote control off). The default setting is rc on. 9 Super-Minature Belt Pack TransmitterRio Rancho, NM Configuring for Power Restore Set Up in 100 kHz Mode When using external power source through a battery eliminator, Power Restore will return your transmitter to settings it had before it was powered off. This eliminates the need to power on through the unit itself. Power Restore Screens 1) Press and hold the Down Arrow Button then power on the transmitter by pressing the Audio and Freq buttons simultaneously. 2) The LCD will display the status, either rc ON or rc OFF. Press AUDIO or FREQ key to scroll to the PbAc setup screen PbAc 1 for power restore ON PbAc 0 for power restore OFF 3) When power restore is set to ON, the unit will turn on whenever power is present at the battery termi-

nals until the power is manually turned off with the control panel switches. NOTE: The firmware remembers the power status when a battery fails, so the transmitter will be turned on automatically when the battery is replaced and the previous settings will be enabled. Power Up and Boot Sequence Frequency displayed Setting Transmitter Operating Frequency The frequency can be displayed either in MHz or as a two-digit hexadecimal number and can be set in the Standby Mode or when the transmitter is powered up. The hexadecimal numbering system is unique to Lectrosonics where two alphanumeric characters correspond to the left and right switch settings on Frequency displayed as two-digit hexadecimal number in MHz earlier analog transmitters that had mechanical rotary switches to adjust frequency. 1) Press the FREQ button to select either the MHZ screen or the hexadecimal screen. 2) While holding the FREQ button, use the Up or Down arrow buttons to move the operating fre-

quency up or down in 100 kHz increments from the current setting. Note: The operating frequency displayed on the LCD wraps as it reaches the upper or lower end of its range. Most Lectrosonics receivers with an LCD interface indicate the operating frequency both in MHz and as a two digit hexadecimal number. In many cases, it is more convenient to use the two character hexadecimal num-

bers rather than the six character frequency in MHz. 10 The Frequency Screen displays the operating frequency in MHz or as a two-digit hexadecimal number that corresponds to the equivalent Lectrosonics Frequency Switch Setting. The example of the two-digit display shown here indicates CH (channel) and 2C as the frequency. Repeatedly pressing the FREQ button toggles between the two displays. Press and hold the FREQ button and use the Up and Down arrows to select the frequency. Set Up in 25 kHz Mode The hexidecimal display in the 25 kHz mode will appear with a decimal suffix to indicate the 25 kHz steps. 471.800 MHz 472.025 MHz 472.650 MHz 473.175 MHz Adjusting the Low Frequency Roll-off Repeatedly press the AUDIO button until the LF roll-

off adjustment screen appears. Then press and hold the AUDIO button while selecting the desired roll-off frequency with the UP and DOWN arrows. The roll-off frequency can be set to 35, 50, 70, 100, 120 and 150 Hz. Adjusting Audio Level (Gain) The control panel Modulation LEDs indicate the audio level and limiter activity. Once set, the transmitters audio level setting should not be used to control the volume of your sound system or recorder levels. This gain adjustment matches the transmitter gain with the microphones output level, the users voice level and the position of the microphone. The audio input level (gain) is adjusted with the unit in the Standby Mode or while powered up while observing the LEDs. It is desirable to to set the gain so that some limiting occurs on louder peaks. The limiter is very transparent and its effect is not audible until the system is close to overload. In other words, dont be shy about turning up the gain. SMV SeriesLECTROSONICS, INC.-10 LED

-20 LED It is actually a good idea to turn the gain up to maxi-

mum and listen for distortion or compression to get a feel for how much headroom is available. Signal Level Less than -20 dB

-20 dB to -10 dB

-10 dB to +0 dB

+0 dB to +10 dB Greater than +10 db Note: Different voices will usually require different gain set-

tings, so check this adjustment as each new person uses the system. If several different people will be using the transmitter and there is not time to make the adjustment for each indi-

vidual, adjust it for the loudest voice. 1) With the transmitter powered off, plug in the mi-

crophone and make sure the connector is firmly seated. Off Green Green Red Red Off Off Green Green Red Warning: If the systems is powered up while connected to a live sound system, be careful to turn the sound system level down first or severe feedback can occur. 2) Place the transmitter in Standby Mode or turn it on for normal use. 3) Position the microphone in the location where it will be used in actual operation. 4) Observe the Modulation LEDs while speaking or singing into the microphone at the same voice level that will be used during operation. While holding the AUDIO button, press the UP or DOWN arrow buttons until the both the -20 and -10 LEDs glow green, with the -20 LED occasionally flickering red. This will maximize the signal to noise ratio of the system with full modulation and provide subtle limit-

ing to prevent overload and audible compression. 5) If the unit was set up in Standby Mode, it will be necessary to turn the transmitter off, then power it up again in normal operation so the RF output will be on. Then the other components in the sound or recording system can be adjusted. Locking or Unlocking the Controls Control Panel Locked The Lock mode protects the transmitter from accidental changes to its settings. Simultaneously press both the Up and Down arrow buttons to start the countdown timer. When the timer reaches zero, Loc is displayed and the controls are locked. Settings can be reviewed but not changed. Once the transmitter is locked, it cannot be unlocked or powered off using the buttons. The only ways to unlock a locked transmitter are to remove the battery or unlock it using the remote control. The remote control will work only if the transmitter was previously configured to respond to the remote control. The unit will always power up in unlocked mode. 5-Pin Input Jack Wiring The wiring diagrams included in this section represent the basic wiring necessary for the most common types of microphones and other audio inputs. Some micro-

phones may require extra jumpers or a slight variation on the diagrams shown. It is virtually impossible to keep completely up to date on changes that other manufacturers make to their products, thus you may encounter a microphone that differs from these instructions. If this occurs please call our toll-free number listed under Service and Repair in this manual or visit our web site at:

www.lectrosonics.com 1 2 3 4 5 GND BIAS MIC BIAS SELECT LINE IN

+5 VDC m h O 0 0 5 100 Ohm k 1

+

30uF Servo Bias Pin 4 to Pin 1 = 0 V Pin 4 Open = 2 V Pin 4 to Pin 2 = 4 V 200 Ohm 30uF

+

100 Ohm To Virtual Ground Audio Amplifier To Limiter Control

+

3.3uF 10k K 7 2

. SM Equivalent Input Circuit Wiring Audio input jack wiring:

PIN 1 Shield (ground) for positive biased electret lava-

liere microphones. Shield (ground) for dynamic microphones and line level inputs. PIN 2 Bias voltage source for positive biased electret lavaliere microphones. PIN 3 Low impedance microphone level input for dynamic microphones. Also accepts hand-held electret microphones provided the microphone has its own built-in battery. PIN 4 Bias voltage selector for Pin 3. Pin 3 voltage (0, 2 or 4 volts) depends on Pin 4 connection. Pin 4 tied to Pin 1: 0 V 2 V Pin 4 Open:

Pin 4 to Pin 2:

4 V PIN 5 High impedance, line level input for tape decks, mixer outputs, musical instruments, etc. 11 Super-Minature Belt Pack TransmitterRio Rancho, NM Installing the Connector:

Line Level Signals 1) If necessary, remove old connector from microphone cable. 2) Slide Rubber Boot onto microphone cable with the large end facing away from the microphone. (See illus-

tration above.) 3) If necessary, slide the 1/8-inch black shrink tubing onto the mircrophone cable. (This tubing is needed for some cables to ensure the cable fits snugly in the rubber boot.) 4) Use the resistors and connector included with this kit to configure the TA5F to your particular microphone.

(See Wiring Diagrams below.) A length of .065 OD clear tubing is included if insulating the resistor leads or shield wire is necessary. (Remove rubber strain relief from connector backshell by pulling it out of the backshell.) 5) Slide the Strain Relief over the TA5F Insert and crimp as shown to the right. Then insert the TA5F Insert and Strain Relief in the TA5F Latchlock. Screw the TA5F Flex Relief onto the TA5F Latchlock. 6) If needed, position and shrink the 1/8-inch shrink tub-

ing on the microphone cable, then slide the Rubber Boot down over the TA5F connector. SMKITTA5 Connector kit for SMV series transmitters, 5-pin TA5F plug with sleeve Insulator Strain Relief Insert The normal hookup for line level signals is: Signal Hot to pin 5, Signal Gnd to pin 1 and pin 4 jumped to pin 1. This allows signal levels up to 3V RMS to be applied without limiting. If more headroom is needed, insert a 20 k resistor in series with pin 5. Put this resistor inside the TA5F con-

nector to minimize noise pickup. TA5F Backshell with Strain Relief Remove strain relief if using dust boot TA5F Latchlock TA5F Backshell

(Strain Relief removed) Dust Boot (P/N 35510) Note: If you use the dust boot, remove the rubber strain relief that is attached to the TA5F cap, or the boot will not fit over the assembly. Microphone RF Bypassing When used on a wireless transmitter, the microphone element is in the proximity of the RF coming from the transmitter. The nature of electret microphones makes them sensitive to RF, which can cause problems with the microphone/transmitter compatibility. If the electret microphone is not designed properly for use with wire-

less transmitters, it may be necessary to install a chip capacitor in the mic capsule or connector to block the RF from entering the electret capsule. Some mics require RF protection to keep the radio signal from affecting the capsule, even though the transmitter input circuitry is already RF bypassed (see schematic diagram). If the mic is wired as directed, and you are having dif-

ficulty with squealing, high noise, or poor frequency response, RF is likely to be the cause. The best RF protection is accomplished by installing RF bypass capacitors at the mic capsule. If this is not pos-

sible, or if you are still having problems, capacitors can be installed on the mic pins inside the TA5F connector housing. 12 2 WIRE MIC 3 WIRE MIC Preferred locations for bypass capacitors SHIELD AUDIO CAPSULE TA5F CONNECTOR CAPSULE SHIELD AUDIO BIAS Alternate locations for bypass capacitors TA5F CONNECTOR Install the capacitors as follows: Use 330 pF capaci-

tors. Capacitors are available from Lectrosonics. Please specify the part number for the desired lead style. Leaded capacitors: P/N 15117 Leadless capacitors: P/N SCC330P All Lectrosonics lavaliere mics are already bypassed and do not need any additional capacitors installed for proper operation. SMV SeriesLECTROSONICS, INC. Microphone Cable Termination for Non-Lectrosonics Microphones TA5F Connector Assembly Mic Cord Stripping Instructions 1 5 4 2 3 VIEW FROM SOLDER SIDE OF PINS 0.15"

0.3"

Crimping to Shield and Insulation Strip and position the cable so that the clamp can be crimped to contact both the mic cable shield and the insulation. The shield contact reduces noise with some microphones and the insulation clamp increases ruggedness. Shield Insulation Crimp these fingers to contact the shield Crimp these fingers to clamp the insulation NOTE: This termination is intended for UHF transmitters only. VHF transmitters with 5-pin jacks require a different termination. Lectrosonics lavaliere microphones are terminated for compatibility with VHF and UHF transmitters, which is different than what is shown here. 13 Super-Minature Belt Pack TransmitterRio Rancho, NM Wiring Hookups for Different Sources In addition to the microphone and line level wiring hook-

ups illustrated below, Lectrosonics makes a number of cables and adapters for other situations such as con-

necting musical instruments (guitars, bass guitars, etc.) to the transmitter. Visit www.lectrosonics.com and click on Accessories, or download the master catalog. A lot of information regarding microphone wiring is also available in the FAQ section of the web site at:

http://www.lectrosonics.com Hover over Support and click on FAQs. Follow the instructions to search by model number or other search options. Compatible Wiring for Both Servo Bias Inputs and Earlier Transmitters:

Fig. 1 Fig. 7 2 VOLT POSITIVE BIAS 2-WIRE ELECTRET BALANCED AND FLOATING LINE LEVEL SIGNALS SHIELD 1.5 k A UDI O Compatible wiring for microphones such as Countryman E6 headworn and B6 lavaliere. 3.3 k Also see Fig. 9 Fig. 2 4 VOLT POSITIVE BIAS 2-WIRE ELECTRET PIN 1 2 3 4 5 4 3 5 1 2 T A5 F PLUG Most common type of wiring for lavaliere mics. WIRING FOR LECTROSONICS M152/5P The M152 lavaliere microphone has an internal resistor and can be wired in a 2-wire configuration. This is the factory standard wiring. RED WHITE

(N/C) Fig. 3 - DPA Microphones DANISH PRO AUDIO MINIATURE MODELS This wiring is for DPA lavalier and headset microphones. NOTE: The resistor value can range from 3k to 4 k ohms. Same as DPA adapter DAD3056 Fig. 4 2 VOLT NEGATIVE BIAS 2-WIRE ELECTRET 2.7 k SHIELD AUDIO Compatible wiring for microphones such as negative bias TRAM models. NOTE: The resistor value can range from 2k to 4k ohms. PIN 1 2 3 4 5 4 3 5 1 2 TA5F PLUG Fig. 5 - Sanken COS-11 and others 4 VOLT POSITIVE BIAS 3-WIRE ELECTRET WITH EXTERNAL RESISTOR SHIELD DRAIN (BIAS) SOURCE (AUDIO) Also used for other 3-wire lavaliere microphones that require an external resistor. Fig. 6 LO-Z MICROPHONE LEVEL SIGNALS XLR JACK For low impedance dynamic mics or electret mics with internal battery or power supply. Insert 1k resistor in series with pin 3 if attenuation is needed 14 XLR JACK

*NOTE: If the output is balanced but center tapped to ground, such as on all Lectrosonics receivers, do not connect Pin 3 of the XLR jack to Pin 4 of the TA5F connector. TA5F PLUG Fig. 8 UNBALANCED LINE LEVEL SIGNALS SLEEVE SHIELD A UDI O LINE LEVEL RCA or 1/4 PLUG TIP For signal levels up to 3V (+12 dBu) before limiting. Fully compatible with 5-pin inputs on other Lectrosonics transmitters such as the LM and UM Series. A 20k ohm resistor can be inserted in series with Pin 5 for an additional 20 dB of attenuation to handle up to 30V (+32 dBu). PIN 1 2 3 4 5 4 3 5 1 2 T A5 F PLUG Simple Wiring - Can ONLY be used with Servo Bias Inputs:

Servo Bias was introduced in 2005 and all trans-

mitters with 5-pin inputs have been built with this feature since 2007. Fig. 9 2 VOLT POSITIVE BIAS 2-WIRE ELECTRET Simplified wiring for microphones such as Countryman B6 Lavalier and E6 Earset models and others. NOTE: This servo bias wiring is not compatible with earlier versions of Lectrosonics transmitters. Check with the factory to confirm which models can use this wiring. Fig. 10 2 VOLT NEGATIVE BIAS 2-WIRE ELECTRET Simplified wiring for microphones such as negative bias TRAM. NOTE: This servo bias wiring is not compatible with earlier versions of Lectrosonics transmitters. Check with the factory to confirm which models can use this wiring. Fig. 11 4 VOLT POSITIVE BIAS 3-WIRE ELECTRET NOTE: This servo bias wiring is not compatible with earlier versions of Lectrosonics transmitters. Check with the factory to confirm which models can use this wiring. SMV SeriesLECTROSONICS, INC. Silver Paste on SM Series Transmitter Thumbscrews Silver paste is applied to thumbscrew threads on new units at the factory to improve the electrical connection from the battery compartment through the housing on any SM Series transmitter. This applies to the standard battery door and the battery eliminator. Threads provide electrical contact The small enclosed vial contains a tiny amount (25 mg) of silver conductive paste. A small speck of this paste will improve the conductivity between the battery cover plate thumbscrew and the case of the SM. The tiny vial is about 1/2 inch tall and contains 25 mg of silver paste. With improved conductivity (lower resistance), more of the battery voltage can get to the internal power sup-

plies causing reduced current drain and longer battery life. Though the amount seems very small, it is enough for years of use. It is, in fact, 25 times the amount that we use on the thumbscrews at the factory. To apply the silver paste, first completely remove the cover plate from the SM housing by backing the thumb-

screw completely out of the case. Use a clean, soft cloth to clean the threads of the thumbscrew. NOTE: Do NOT use alcohol or a liquid cleaner. Simply hold the cloth around the threads and turn the thumbscrew. Move to a new spot on the cloth and do it again. Do this until the cloth remains clean. Now, clean the threads in the case by using a dry cotton swab (Q-

tip) or equivalent. Again, clean the case threads until a fresh cotton swab comes away clean. Open the vial, and transfer a pinhead speck of silver paste to the second thread from the end of the thumb-

screw. A easy way to pickup a speck of paste is to partially unfold a paper clip and use the end of the wire to acquire a tiny bit of paste. A toothpick will also work. An amount that covers the end of the wire is sufficient. Apply paste to second thread from end of thumbscrew It is not necessary to spread the paste more than a little bit on the thread as the paste will spread itself every time the thumbscrew is screwed in and out of the case during battery changes. Do not apply the paste to any other surfaces. The cover plate itself can be cleaned with a clean cloth by rubbing the slightly raised rings on the plate where it contacts the battery terminal. All you want to do is to remove any oils or dirt on the rings. Do not abrade these surfaces with a harsh material such as a pencil eraser, emery paper, etc., as this will remove the conductive nickel plating and expose the underlying aluminum, which is a poor contact conductor. 15 Super-Minature Belt Pack TransmitterRio Rancho, NM The Android version keeps all settings on the same page and allows the user to toggle between the activa-

tion buttons for each setting. The activation button must be long pressed to activate. The Android version also allows users to keep a configurable list of full sets of settings. Activation For a transmitter to respond to remote control audio tones, the transmitter must meet certain requirements:

The transmitter must not be turned off; it can however be in sleep mode. The transmitter must have firmware version 1.5 or later for Audio, Frequency, Sleep and Lock changes. The transmitter microphone must be within range. The transmitter must be configured to enable remote control activation. Please be aware this app is not a Lectrosonics product. It is privately owned and operated by New Endian LLC, www.newendian.com. LectroRM Android SM Series WM L Series By New Endian LLC LectroRM is a mobile application for iOS and Android operating systems. Its purpose is to remotely control Lectrosonics Transmitters, including:

The app remotely changes settings on the transmitter through the use of encoded audio tones, which when received by the attached microphone, will alter the configured setting. The app was released by New En-

dian, LLC in September 2011. The app is available for download and sells for $20 on the Apple App Store and Google Play Store. LectroRMs remote control mechanism is the use of an audio sequence of tones (dweedles) that are inter-

preted by the transmitter as a configuration change. The settings available in LectroRM are:

Audio Level Frequency Sleep Mode Lock Mode User Interface The user interface involves selecting the audio se-

quence related to the desired change. Each version has an interface for selecting the desired setting and the desired option for that setting. Each version also has a mechanism to prevent accidental activation of the tone. iOS The iPhone version keeps each available setting on a separate page with the list of options for that setting. On iOS, the Activate toggle switch must be enabled to show the button which will then activate the audio. The iOS versions default orientation is upside-down but can be configured to orient right-side up. The purpose for this is to orient the devices speaker, which is at the bot-

tom of the device, closer to the transmitter microphone. 16 SMV SeriesLECTROSONICS, INC. Straight Whip Antennas This is a full size cutting template used to cut the length of the whip for a particular frequency. Lay the uncut antenna on top of this drawing and trim the whip length to the desired frequency. After cutting the antenna to the desired length, mark the antenna by installing a color cap or sleeve to indicate the color listed in the table below Whip Length The supplied caps can be used several different ways:

1) A color cap on the end of the whip 2) A color sleeve next to the connector with a black cap on the end of the whip (trim the closed end of the colored cap off with scissors to make a sleeve). 3) A color sleeve and color cap (cut the cap in half with scissors). 4 4 9 9 2 8 2 7 2 6 2 5 2 4 2 3 2 2 2 1 2 0 2 9 1 0 7 4 Note: Check the scale of your printout. This line should be 6.00 inches long (152.4 mm). BLOCK FREQUENCY RANGE CAP/SLEEVE COLOR ANTENNA WHIP LENGTH 470 19 20 21 22 23 24 25 26 944 470.100 - 495.600 486.400 - 511.900 512.000 - 537.500 537.600 - 563.100 563.200 - 588.700 588.800 - 614.300 614.400 - 639.900 640.000 - 665.500 665.600 - 691.100 944.100 - 951.900 Black w/ Label Black w/ Label Black w/ Label Brown w/ Label Red w/ Label Orange w/ Label Yellow w/ Label Green w/ Label Blue w/ Label Black-w/Label 5.67 5.23 4.98 4.74 4.48 4.24 4.01 3.81 3.62 2.62 NOTE:

Not all Lectrosonics products are built on all of the blocks covered in this table. Factory supplied antennas precut to length include a label with the frequency range. Label is not supplied with this kit. 17 Super-Minature Belt Pack TransmitterRio Rancho, NM Accessories for single battery models:

PSM Leather pouch with integrated belt clip Accessories for dual battery models:

PSMD Leather pouch with integrated belt clip SMBCUPSL Spring-loaded machined aluminum clip SMDBCSL Spring-loaded machined aluminum clip SMBCDN Machined, wire belt clip for SMV transmitters, antenna down SMDBC Machined, wire belt clip for SMQV transmitters SMBCUP Machined, wire belt clip for SMV transmitters, antenna up 35924 Themal insulated pad installed for SMQV Place thermal insulation pad on back of unit, as pictured. 18 SMV SeriesLECTROSONICS, INC. Accessories for Both Models SMBATELIM External power adapter (battery elimina-

tor) for all SM Series transmitters. 6 to 36 volt external sources. Handles up to 1 amp consumption. Protected against shorts and reverse polarity. To install the battery eliminator, loosen the thumbscrew completely and remove the battery door. Insert the bat-

tery eliminator and tighten the thumbscrew. SMKITTA5 Microphone connector kit with watertight sleeve for all SM Series transmitters. 19 Super-Minature Belt Pack TransmitterRio Rancho, NM Troubleshooting Before going through the following chart, be sure that you have a good battery in the transmitter. It is important that you follow these steps in the sequence listed. SYMPTOM POSSIBLE CAUSE TRANSMITTER PWR LED OFF TRANSMITTER PWR LED BLINKS GREEN EVERY FEW SECONDS, TRANSMITTER DOES NOT RESPOND OTHERWISE 1) Battery is inserted backwards or dead. 2) Transmitter not powered up. (See Operating Instructions, 1) Transmitter has been put to sleep by the remote control. Either use the remote control to wake it up again or remove and reinsert the transmitters battery. Power UP and Boot Sequence.) AUDIO LEVEL LEDs NOT LIGHTING 1) Gain control set to minimum. 2) Battery is dead or installed backwards. Check PWR LED. 3) Mic capsule is damaged or malfunctioning. 4) Mic cable damaged or mis-wired. RECEIVER RF INDICATOR OFF 1) Transmitter not turned on, or is in Standby Mode. 2) Transmitter battery is dead. 3) Receiver antenna missing or improperly positioned. 4) Transmitter and receiver not on same frequency. 5) Transmitter and receiver not on same frequency block. 6) Operating range is too great. 7) Defective transmitter antenna. Check switches/display on transmitter and receiver. NO SOUND (OR LOW SOUND LEVEL), RECEIVER INDICATES PROPER AUDIO MODULATION 1) Receiver output level set too low. 2) Receiver output disconnected, or cable defective or mis-wired. 3) Sound system or recorder input is turned down. LEDs and receiver audio levels during use. 1) Transmitter gain (audio level) is far too high. Check audio level 2) Receiver output may be mismatched with the sound system or 3) Transmitter is not set to same frequency as receiver. Check that operating frequency on receiver and transmitter match. 4) Receiver/Transmitter Compatibility Mode mismatched. recorder input. Adjust output level on receiver to the correct level for the recorder, mixer or sound system. (Use the receivers Tone function to check level.) and/or reduce receiver output level. 1) Transmitter gain (audio level) too high. Check gain adjustment 2) Talent standing too close to speaker system. 3) Mic is too far from users mouth. DISTORTED SOUND EXCESSIVE FEEDBACK 20 SMV SeriesLECTROSONICS, INC. SYMPTOM POSSIBLE CAUSE 1) Transmitter gain (audio level) far too low. 2) Receiver antenna missing or obstructed. 3) Transmitter antenna broken or missing. 4) Operating range too great. 5) Signal interference. Turn off transmitter. If receivers signal strength indicator does not drop to nearly zero, this indicates an interfering signal may be the problem. Try a different operating frequency. 1) Control Panel is locked. (See Operating Instructions, Locking and Unlocking the Control Panel.) HISS AND NOISE -- AUDIBLE DROPOUTS Loc APPEARS IN DISPLAY WHEN ANY BUTTON IS PRESSED Hold APPEARS IN DISPLAY WHEN ARROW BUTTONS ARE PRESSED PLL APPEARS IN DISPLAY TRANSMITTER WONT RESPOND TO REMOTE CONTROL button to make adjustments to the audio gain or frequency settings. 1) Reminder that it is necessary to hold down the AUDIO or FREQ 1) Indication that the PLL is not locked. This is a serious condition that requires factory repair. It may be possible to operate on another frequency far removed from the one that was selected when the condition was indicated. requested by the remote control. to respond to the remote control. See Remote Control Operation on page 7 for instructions on how to configure. 1) If LCD blinks rc oFF, transmitter has not been configured 2) If LCD blinks - - - - - -, transmitter is already set as 3) If transmitter does not respond at all, try moving the remote 4) Make sure volume of RM and proximity of microphone are 5) Make sure transmitter is not in Sleep mode. control closer to the microphone or increasing the remote controls loudness setting, or increasing the audio level on the transmitter. sufficient to engage transmitter. 21 Super-Minature Belt Pack TransmitterRio Rancho, NM Specifications and Features Operating frequencies:

Block 470 470.100 - 495.675 486.400 - 511.975 Block 19 Block 20 512.000 - 537.575 Channel Spacing:

Frequency selection:

RF Power output:

Compatibility Modes:

Pilot tone:

Frequency stability:

Spurious radiation:

Equivalent input noise:

Input level:

If set for dynamic mic:

Input impedance:

Dynamic mic:

Electret lavaliere:

Line level:

Input limiter:

Bias voltages:

Gain control range:

Modulation indicators:

Controls:

If set for electret lavaliere mic:

Line level input:

Block 21 537.600 - 563.175 Block 22 563.200 - 588.775 Block 23a 588.800 - 607.950 Selectable; 25 or 100 kHz Control panel mounted membrane switches Selectable; 50, 100 or 250 mW Nu Hybrid, Mode 3, IFB 3.5 kHz deviation (Nu Hybrid) 0.002%

Compliant with ETSI EN 300 422-1 v1.4.2 125 dBV, A-weighted 0.5 mV to 50 mV before limiting. Greater than 1 V with limiting. 1.7 uA to 170 uA before limiting. Greater than 5000 uA

(5 mA) with limiting. 17 mV to 1.7 V before limiting. Greater than 50 V with limiting. 300 Ohms Input is virtual ground with servo adjusted constant current bias 2.7 k Ohms Soft limiter, 30 dB range Fixed 5 V at up to 5 mA; Selectable 2 V or 4 V servo bias for any electret lavaliere. 44 dB; panel mounted membrane switches Dual bicolor LEDs indicate modulation of 20, -10, 0,

+10 dB referenced to full modulation. Control panel with LCD and four membrane switches. Adjustable from 35 to 150 Hz. 35 Hz to 20 kHz, +/-1 dB (The low frequency roll-off is adjustable - see graph on page 2) Low frequency roll-off:

Audio Frequency Response:

Signal to Noise Ratio (dB):

(overall system, Nu Hybrid mode)

(Note: the dual envelope soft limiter provides exceptionally good handling of transients using variable attack and release time constants. The gradual onset of limiting in the design begins below full modulation, which reduces the measured figure for SNR without limiting by 4.5 dB) No Limiting 103.5 107.0 108.5 SmartNR OFF NORMAL FULL w/Limiting 108.0 111.5 113.0 Total Harmonic Distortion:

Audio Input Jack:

Antenna:

Batteries:

0.2% typical (Nu Hybrid mode) Switchcraft 5-pin locking (TA5F) Flexible, unbreakable, detachable steel cable. 1.5 Volt AA (Lithium recommended) Unit/Power SMV 50 mW (1 AA):

SMV 100 mW (1 AA):

SMV 250 mW (1 AA):

Battery Life 7.25 hrs 5.5 hrs 3 hrs SMQV 50 mW (2 AA):

14.5 hrs SMQV 100 mW (2 AA):

SMQV 250 mW (2 AA):

14 hrs 7.5 hrs Weight with Battery:

Overall Dimensions:

Emission Designator:

SMV: 2.7 oz. (75.9 grams) SMQV: 3.7 oz. (105 grams) SMV: 2.3 x 1.8 x 0.64 inches SMQV: 2.3 x 2.4 x 0.64 inches 58 x 60 x 16 mm 58 x 46 x 16 mm 110KF3E Specifications subject to change without notice. 22 SMV SeriesLECTROSONICS, INC. Service and Repair If your system malfunctions, you should attempt to correct or isolate the trouble before concluding that the equipment needs repair. Make sure you have followed the setup procedure and operating instructions. Check the interconnecting cables and then go through the Troubleshooting section in this manual. We strongly recommend that you do not try to repair the equipment yourself and do not have the local repair shop at-

tempt anything other than the simplest repair. If the repair is more complicated than a broken wire or loose connection, send the unit to the factory for repair and service. Dont attempt to adjust any controls inside the units. Once set at the factory, the various controls and trimmers do not drift with age or vibration and never require readjustment. There are no adjustments inside that will make a malfunctioning unit start working. LECTROSONICS Service Department is equipped and staffed to quickly repair your equipment. In warranty repairs are made at no charge in accordance with the terms of the warranty. Out-of-warranty repairs are charged at a modest flat rate plus parts and shipping. Since it takes almost as much time and effort to determine what is wrong as it does to make the repair, there is a charge for an exact quotation. We will be happy to quote approximate charges by phone for out-of-warranty repairs. Returning Units for Repair For timely service, please follow the steps below:

A. DO NOT return equipment to the factory for repair without first contacting us by email or by phone. We need to know the nature of the problem, the model number and the serial number of the equipment. We also need a phone number where you can be reached 8 A.M. to 4 P.M. (U.S. Mountain Standard Time). B. After receiving your request, we will issue you a return authorization number (R.A.). This number will help speed your repair through our receiving and repair departments. The return authorization number must be clearly shown on the outside of the shipping container. C. Pack the equipment carefully and ship to us, shipping costs prepaid. If necessary, we can provide you with the proper packing materials. UPS is usually the best way to ship the units. Heavy units should be double-boxed for safe transport. D. We also strongly recommend that you insure the equipment, since we cannot be responsible for loss of or dam-

age to equipment that you ship. Of course, we insure the equipment when we ship it back to you. Lectrosonics USA:

Mailing address:

Lectrosonics, Inc. PO Box 15900 Rio Rancho, NM 87174 USA Web:

www.lectrosonics.com Shipping address:

Lectrosonics, Inc. 581 Laser Rd. Rio Rancho, NM 87124 USA E-mail:

sales@lectrosonics.com Telephone:

(505) 892-4501

(800) 821-1121 Toll-free

(505) 892-6243 Fax Lectrosonics Canada:

Mailing Address:

720 Spadina Avenue, Suite 600 Toronto, Ontario M5S 2T9 Telephone:

(416) 596-2202

(877) 753-2876 Toll-free

(877-7LECTRO)

(416) 596-6648 Fax E-mail:

Sales:

Service: joeb@lectrosonics.com colinb@lectrosonics.com LIMITED ONE YEAR WARRANTY The equipment is warranted for one year from date of purchase against defects in materials or workmanship provided it was purchased from an authorized dealer. This warranty does not cover equipment which has been abused or damaged by careless handling or shipping. This warranty does not apply to used or demonstrator equipment. Should any defect develop, Lectrosonics, Inc. will, at our option, repair or replace any defective parts without charge for either parts or labor. If Lectrosonics, Inc. cannot correct the defect in your equipment, it will be replaced at no charge with a similar new item. Lectrosonics, Inc. will pay for the cost of returning your equipment to you. This warranty applies only to items returned to Lectrosonics, Inc. or an authorized dealer, shipping costs prepaid, within one year from the date of purchase. This Limited Warranty is governed by the laws of the State of New Mexico. It states the entire liablility of Lectrosonics Inc. and the entire remedy of the purchaser for any breach of warranty as outlined above. NEITHER LECTROSONICS, INC. NOR ANYONE INVOLVED IN THE PRODUCTION OR DELIVERY OF THE EQUIPMENT SHALL BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, CONSEQUENTIAL, OR INCIDENTAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THIS EQUIPMENT EVEN IF LECTROSONICS, INC. HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL THE LIABILITY OF LECTROSONICS, INC. EXCEED THE PURCHASE PRICE OF ANY DEFECTIVE EQUIPMENT. This warranty gives you specific legal rights. You may have additional legal rights which vary from state to state. 581 Laser Road NE Rio Rancho, NM 87124 USA www.lectrosonics.com

(505) 892-4501 (800) 821-1121 fax (505) 892-6243 sales@lectrosonics.com 19 October 2018