FCC ID: DBZSSMA1A Wireless Microphone Transmitter

INSTRUCTION MANUAL SSM Micro Bodypack Transmitter Quick Start Steps 1) Install a good battery and turn power on (see pages 5 and 8). 2) Set the compatibility mode to match the receiver (see page 9). 3) Connect the signal source and adjust input gain for optimum modulation level (see page 10). 4) Set Step Size and frequency to match receiver (see pages 8 and 9). Also refer to the receiver manual for the RF scanning procedure to find a clear operating frequency. 5) Turn on the receiver and verify that solid RF and audio signals are present (see receiver manual). WARNING: Moisture, including talents sweat, will damage the transmitter. Wrap the SSM in a plastic bag or other protection to avoid damage. Fill in for your records:

Serial Number:

Purchase Date:

Rio Rancho, NM, USA www.lectrosonics.com 2 SSMLECTROSONICS, INC. Table of Contents Quick Start Steps ..................................................................................................................................................................................1 About Digital Hybrid Wireless .................................................................................................................................................................................................................................................................................4 Battery Charging ....................................................................................................................................................................................5 Battery Installation .................................................................................................................................................................................5 Controls and Functions .........................................................................................................................................................................6 Modulation LEDs ...................................................................................................................................................................................6 LCD Screen ..........................................................................................................................................................................................6 BATT LED .............................................................................................................................................................................................6 AUDIO Button .......................................................................................................................................................................................6 FREQ Button .........................................................................................................................................................................................6 Power Button .........................................................................................................................................................................................6 UP and DOWN Arrow Buttons ..............................................................................................................................................................6 Turning LEDs ON and OFF ...................................................................................................................................................................6 See Operating Instructions and Setup Screens for complete information.............................................................................................6 Connectors and USB Port .....................................................................................................................................................................7 Attaching and Removing the Microphone ............................................................................................................................................7 Operating Instructions ...........................................................................................................................................................................8 Powering On in Operating Mode ...........................................................................................................................................................8 Powering On in Standby Mode .............................................................................................................................................................8 Powering Off .........................................................................................................................................................................................8 Setup Screens ......................................................................................................................................................................................8 Screens Used in Normal Operation ......................................................................................................................................................8 Block 470/19 Frequency Overlap ..........................................................................................................................................................8 Call the factory if you have questions about this issue. .......................................................................................................................8 Setup Steps ..........................................................................................................................................................................................9 Locking the Controls ..............................................................................................................................................................................9 Adjusting the Input Gain ........................................................................................................................................................................9 Setup Screens ....................................................................................................................................................................................10 DOWN Button Menu ...........................................................................................................................................................................10 UP Button Menu ..................................................................................................................................................................................10 Microphone Wiring ...............................................................................................................................................................................11 Line Input Wiring and Use ...................................................................................................................................................................11 IR (infrared) Sync ..................................................................................................................................................................................12 Removable Belt Clips ...........................................................................................................................................................................12 Remote Control .....................................................................................................................................................................................12 LectroRM ...............................................................................................................................................................................................13 Accessories ..........................................................................................................................................................................................14 Firmware Update ..................................................................................................................................................................................15 Specifications ......................................................................................................................................................................................17 Service and Repair ...............................................................................................................................................................................18 Returning Units for Repair ..................................................................................................................................................................18 3 Micro Body Pack TransmitterRio Rancho, NM About Digital Hybrid Wireless US Patent 7,225,135 All wireless links suffer from channel noise to some degree, and all wireless microphone systems seek to minimize the impact of that noise on the desired signal. Conventional analog systems use compandors for enhanced dynamic range, at the cost of subtle artifacts

(known as pumping and breathing). Wholly digital systems defeat the noise by sending the audio informa-

tion in digital form, however, it is often at the cost of one or more issues regarding power, bandwidth, operating range and resistance to interference. The Lectrosonics Digital Hybrid Wireless system over-

comes channel noise in a dramatically new way, digitally encoding the audio in the transmitter and decoding it in the receiver, yet still sending the encoded informa-

tion via an analog FM wireless link. This proprietary algorithm is not a digital implementation of an analog compandor but a technique which can be accomplished only in the digital domain. Since the RF link between transmitter and receiver is FM, channel noise will increase gradually with in-

creased operating range and weakened signal condi-

tions; however, the Digital Hybrid Wireless system handles this situation elegantly with barely audible audio artifacts as the receiver approaches its squelch threshold. In contrast, a purely digital system tends to drop the audio suddenly during brief dropouts and weak signal conditions. The Digital Hybrid Wireless system simply encodes the signal to use a noisy channel as efficiently and robustly as possible, yielding audio performance that rivals that of purely digital systems, without the power, noise and bandwidth problems inherent in digital transmission. Because it uses an analog FM link, Digital Hybrid Wireless enjoys all the benefits of conventional FM wireless systems, such as excellent range, efficient use of RF spectrum, and long battery life. 4 SSMLECTROSONICS, INC. Battery Installation The battery compartment and door catch are designed for simple and quick battery changes, yet prevent the door from being opened accidentally. Battery Charging The transmitter operates from a 3.6 V rechargeable battery that will provide about six hours of operation per charge. Battery life can be monitored from the timer function built into current Lectrosonics receivers. Squeeze tabs inward to release door catch Battery contacts The factory supplied battery charger kit provides a folding NEMA 2-prong plug on the charger, and will operate from 100-240 VAC sources. The LED glows red during charging and turns green when the battery is fully charged. The kit includes a Euro plug adapter and vehicle auxiliary power adapter cord. Battery charger kit P/N 40107 Insert battery contact end first CAUTION: Use only the factory supplied battery and battery charger. Press opposite end of battery into compartment 5 Micro Body Pack TransmitterRio Rancho, NM BATT LED This LED glows green when the battery is good. The color changes to red when there is only a few minutes of operation left. The LED will blink briefly, just before the unit powers down. The exact point at which the LED turns red will vary with battery brand and condition, temperature and cur-

rent drain. The LED is intended to simply catch your attention, not to be an exact indicator of remaining time. AUDIO Button The AUDIO button is used to adjust the audio output level and low frequency roll-off. Each press of the button will toggle between the two settings. FREQ Button The FREQ Button displays the selected operating frequency and toggles the LCD between displaying the actual operating frequency in MHz and a two-digit hexadecimal number that corresponds to the equivalent Lectrosonics Frequency Switch Setting. Power Button Turns the unit on and off. A brief press turns power on in a Standby Mode to make settings without interfering with other wireless systems in the vicinity. Pressing and holding the button until a counter on the LCD completes a sequence turns the power on with the RF output turned on. Pressing and holding for the duration of a countdown turns the unit off. UP and DOWN Arrow Buttons The Up and Down arrow buttons are used to select the values on the various setup screens and to lock out the control panel. Turning LEDs ON and OFF These arrow keys also turn the LEDs on and off. With no other button pressed, the UP arrow turns the LEDs on and the DOWN arrow turns them off. When the LEDs turn red, the LCD will display a reminder every few seconds. See Operating Instructions and Setup Screens for complete information. Controls and Functions Modulation LEDs BATT LED Power Button Modulation LEDs Proper input gain adjustment is critical to ensure the best audio quality. Two bicolor LEDs will glow either red or green to accurately indicate modulation levels. The input circuitry includes a wide range DSP controlled limiter to prevent distortion at high input levels. It is important to set the gain (audio level) high enough to achieve full modulation during louder peaks in the audio. The limiter can handle over 30 dB of level above full modulation, so with an optimum setting, the LEDs will flash red during use. If the LEDs never flash red, the gain is too low. In the table below, +0 dB indicates full modulation. Signal Level Less than -20 dB

-20 dB to -10 dB

-10 dB to +0 dB

+0 dB to +10 dB Greater than +10 db Off Green Green Red Red Off Off Green Green Red

-20 LED

-10 LED LCD Screen The LCD is a numeric-type Liquid Crystal Display with screens for adjusting output power, frequency, audio level, low frequency audio roll-off and various modes and options. The transmitter can be powered up with or without the RF output turned on. A brief press on the power button turns the unit on in a Standby Mode with the output turned off to allow adjustments to be made without interfering with other wireless systems in the vicinity. WARNING: Moisture, including talents sweat, will damage the transmitter. Wrap the SSM in a plastic baggie or other protection to avoid damage. 6 SSMLECTROSONICS, INC. Connectors and USB Port The housing is machined out of a solid aluminum billet for a rugged, lightweight assembly. IR (infrared) port Galvanized steel flexible whip antenna Attaching and Removing the Microphone Align the ridges on the plug with the grooves in the jack and insert the plug. Mic/Line input jack The antenna is a flexible whip made of galvanized steel, permanently attached to the transmitter to prevent damage from heavy use. The IR port is capped with a translucent dome material to broaden the reception angle. The input jack is a rugged 3-pin LEMO connector with a threaded locking sleeve. The opposite end of the transmitter contains the battery door latches and release tabs, and the USB port, which is used for firmware updates. Battery door release tabs Grooves in the jack must align with ridges on the plug Slide the threaded sleeve onto the jack and rotate it clockwise to tighten it. Removable belt clip Battery door latch USB port The battery door itself is made of stainless steel to allow a thin wall thickness, but retain the strength to withstand heavy use. Tighten the sleeve to secure the connection 7 Micro Body Pack TransmitterRio Rancho, NM Operating Instructions Powering On in Operating Mode Press and hold the Power Button until a counter on the LCD progresses from 1 through 3, followed by a display of the model, firmware version, frequency block and compatibility mode. for several seconds Screens Used in Normal Operation When the transmitter is turned on with the RF output on, the LCD will display the frequency, audio gain or LF roll-off point. Audio gain is expressed in dB. When you release the button, the unit will be operation-

al with the RF output turned on and the Main Window displayed. Powering On in Standby Mode A brief press of the Power Button

, releasing it before the counter has reached 3, will turn the unit on with the RF output turned off. The LCD will display a reminder that the RF output of the transmitter is turned off. In this Standby Mode the frequency can be browsed to make adjustments without the risk of interfering with other wireless systems nearby. After adjustments are made, press the power button again to turn the unit off. Powering Off Holding the Power Button completion of the countdown from 3 to 1 will turn the power off. in and waiting for the Frequency is displayed in one of two ways:

Frequency expressed in MHz Standard frequency block (22) Frequency in hex code (C8) Offset in MHz (.75) LF roll-off is expressed in Hz. To make changes to the settings, press either button to display the desired screen, then use the UP and DOWN arrows to select the value. The changes take effect im-

mediately when you release the buttons. Block 470/19 Frequency Overlap If the power button is released before the countdown is completed, the unit will remain turned on and the LCD will return to the same screen or menu that was dis-

played previously. Setup Screens Two different setup menus are accessed by holding either the UP or DOWN arrow button while powering the unit on. See the following page (Setup Screens) for a listing of the menu items and descriptions. Frequencies 486.400 - 495.600 Overlap in Blocks 470 and 19 Block 470 and block 19 overlap each other in the frequency range from 486.400 to 495.600 MHz. Since block 470 starts at a lower frequency than block 19, the hex codes (and pilot tones) will not match even though the frequencies are the same in the overlap zone. When using a transmitter on the A1 band with a block 19 receiver, be sure the transmitter is set to block 19 and check the hex code on the receiver to make sure it matches the transmitter. Call the factory if you have questions about this issue. 8 SSMLECTROSONICS, INC. Setup Steps The setup menus are accessed by holding either the UP or DOWN arrow while powering the unit on. Refer to Setup Screens on the next page for details of each setup parameter. The following list outlines the steps necessary to set up the transmitter for normal use. 1) Install a charged battery. 2) Set the compatibility mode to match the receiver to be used. 3) Adjust the step size and frequency to match the re-

ceiver. The frequency is normally determined using the receiver to identify one within clear operating spectrum. Refer to the receiver instructions for de-

tails on using features such as scanning. NOTE: Some Lectrosonics receivers include an IR (infrared) port to transfer settings from the receiver to the transmitter. Refer to the section on IR (infrared) Sync for details. 4) Connect the microphone or audio source to be used. Select the correct input configuration. 5) Adjust the input gain. Refer to Adjusting the Input Gain for details. 6) Turn on the receiver and verify that solid RF and audio signals are present (see receiver manual). Locking the Controls The firmware version is displayed briefly when powering up the transmitter. For firmware versions 1.06 and lower:

Lock the controls by holding the UP and DOWN ar-

rows until a count displayed on the LCD is completed and Loc appears on the LCD. To unlock the controls, remove the battery. For firmware versions 1.07 and higher:

Lock the controls by holding the UP and DOWN arrows until a count displayed on the LCD is completed and Loc appears on the LCD. To unlock the controls, hold the UP and DOWN arrows until a count on the LCD is completed and unloc appears on the LCD. Removing the battery does not unlock the controls. Adjusting the Input Gain The two bicolor Modulation LEDs on the control panel provide a visual indication of the audio signal level entering the transmitter. The LEDs will glow either red or green to indicate modulation levels as shown in the following table. Signal Level Less than -20 dB

-20 dB to -10 dB

-10 dB to +0 dB

+0 dB to +10 dB Greater than +10 dB Off Green Green Red Red Off Off Green Green Red

-20 LED

-10 LED NOTE: Full modulation is achieved at 0 dB, when the -20 LED first turns red. The limiter can cleanly handle peaks up to 30 dB above this point. It is best to go through the following procedure with the transmitter in the standby mode so that no audio will en-

ter the sound system or recorder during adjustment. 1) With a charged battery in the transmitter, power the unit on in the standby mode (see previous section Powering On in Standby Mode). 2) Press and hold the AUDIO button with Aud and a numeral on the display (e.g. Aud 22). 3) Prepare the signal source. Position a microphone the way it will be used in actual operation and have the user speak or sing at the loudest level that occur during use, or set the output level of the instrument or audio device to the maximum level that will be used. 4) Use the arrow buttons to adjust the gain until the 10 dB glows green and the 20 dB LED starts to flicker red during the loudest peaks in the audio. and 5) Once the audio gain has been set, the signal can be sent through the sound system for overall level adjustments, monitor settings, etc. 6) If the audio output level of the receiver is too high or low, use only the controls on the receiver to make adjustments. Unless the microphone or its position changes, or a different instrument is being used, leave the transmitter gain adjustment set accord-

ing to these instructions. Use the audio output level control on the receiver to make adjustments for the desired level being delivered to the connected mixer, recorder, etc. 9 Micro Body Pack TransmitterRio Rancho, NM Setup Screens DOWN Button Menu Hold the DOWN button while powering up the unit. Then press the AUDIO button repeatedly to scroll through the following settings. Use the UP and DOWN arrows to select the available options under each setting. rc - remote control operation; selections: on, oFF PbAc - power-back-on after power loss; selections: 0 (stay turned off), 1 (turn back on) bL - back light duration; selections: 5 (minutes), 30 (seconds), on (always on) UP Button Menu Hold the UP button while powering up the unit. Then press the AUDIO button repeatedly to scroll through and se-

lect the following settings (bulleted). Use the UP and DOWN arrows to select the available options under each setting. CP - compatibility mode; press the UP and DOWN arrows to select one of the following:

CP Nu CP 3 CP IFb Nu Hybrid mode Mode 3 (contact the factory for details) IFB Series mode; IFBR1/1a receivers Pr - RF power output; selections: 25, 50 In - Input configuration; press the UP and DOWN arrows to select one of the following:

In dYn In 152 In SEn In SEt bIAS 0, rES 0; use for dynamic microphones bIAS 4, rES 0; same as otH; listed for easy selection on Lectrosonics 152 and similiar mics bIAS 4, rES 0; same as otH; listed for easy selection on Sennheiser MKE 2 and similiar mics Press the AUDIO button for manual setup of input for explicit control over bias voltage, input resistance and audio polarity. Press the AUDIO button to select the following parameters, then use the UP and DOWN arrows for each item to set the values. bIAS - bias voltage on the input; selections 0, 2 or 4 rES - input impedance; selections: 0 (300 ohms), Lo (approx. 4 k ohms) or HI (approx. 100 k ohms) AP - audio polarity (aka phase); selections: P for positive, n for negative (reversed) NOTE: When you press AUDIO after setting the polarity, the screen will leave this submenu and return to the In menu. To return to this submenu, press AUDIO repeatedly and scroll through the list again. In otH In L In In dPA In b6 In CoS StP - Frequency tuning step size in kHz; selections: 25 kHz or 100 kHz bIAS 4, rES 0; same as CoS but audio phase is not reversed; for various mics bIAS 0, rES HI; use for line level input (See Line Input Wiring and Use on page 11) bIAS 4, rES Lo; use for DPA lavaliere and similar mics bIAS 2, rES 0; use for Countryman B6 and similar mics bIAS 4, rES 0; phase reversed; use for Sanken COS-11, M152 and similar mics 10 SSMLECTROSONICS, INC. Microphone Wiring Looking into the 3 pin Lemo mic connector from the outside of the transmitter, the pin centered in the two guide slots is pin 1 (ground). Pin 2 is a 1k resistor to ground. Pin 3 is the audio/bias connection for two-wire microphones and line inputs. Pin 1 Guide slots Line Input Wiring and Use Pin Configuration:

Pin 1: Shield (ground) Pin 2: Audio Transmitter Settings:

Input Setting Unlike the old configuration, the new line input configura-

tion requires no fixed gain setting. The gain setting can be adjusted as needed for the specific input level used. Pin 2 Pin 3 Voltages, polarity, impedance and line level for all signal sources are selected by menus. Menu selections in-

clude presets for popular microphones, and a sub-menu for manual setup. Refer to the section entitled Setup Screens on the previous page for details. Two-wire electret lavaliere:

Pin 1 - Ground (shield) Pin 3 - Audio and Bias Sanken COS-11 lavaliere Recommended Wiring:

Pin 1 - Shield (ground) Pin 2 - White (source load) Pin 3 - Black (bias and audio) NOTE: The COS-11 can also be wired in a two-

wire configuration. Contact Plus24/Sanken for details. The Sanken CUB-01 is not supported. 11 Micro Body Pack TransmitterRio Rancho, NM IR (infrared) Sync An IR (infrared) link between an associated receiver and the transmitter can be used to shorten setup time and ensure that the correct settings in the transmitter are made. The dome on the side panel of the transmit-

ter is the port used for the IR link. The receiver is nor-

mally used to identify a clear operating frequency. Once step size, frequency and compatibility mode are set in the receiver, the settings can be sent to the transmitter via this IR link. IR port Place the transmitter close to the IR enabled receiver with the ports facing each other within a foot or two apart. Send the settings with the trigger on the receiver. If the settings are successfully transferred, a confirma-

tion message will appear on the transmitter LCD. NOTE: If a mismatch exists between the receiver and transmitter, an error message will appear on the transmitter LCD stating what the problem is. Removable Belt Clips Two different belt clips are available, one that orients the antenna downward and another one that orients the antenna upward. Attaching and removing the clips is the same for both models. A belt clip is removed by rotating it as shown and sliding it off the retaining tabs on the battery door. Alignment notch Mounting holes To attach a belt clip, align the notches with the retaining tabs, then press on the clip to attach it. Press clip into place with tabs seated in mounting holes The antenna works equally well when oriented either upward or downward. Position the transmitter so that the antenna is not in contact with or underneath any metallic object or surface in wardrobe or costuming, and preferably with a layer of fabric between the antenna and the users body. Remote Control Remote control signals (dweedle tones) may be used to control the transmitter. The tones are played back into the microphone to avoid the need to reach and handle the transmitter when making changes to the following adjustments and settings:

Input Gain Sleep/Unsleep Lock/Unlock Tx power output Frequency A smart phone app is available in the App Store and in Google Play to implement this control. Search for the title LectroRM. Retaining tabs 12 SSMLECTROSONICS, INC. LectroRM By New Endian LLC LectroRM is a mobile application for iOS and Android smart phone operating systems. Its purpose is to make changes to the settings on select Lectrosonics transmit-

ters by delivering encoded audio tones to the micro-

phone attached to the transmitter. When the tone enters the transmitter, it is decoded to make a change to a va-

riety of different settings such as input gain, frequency and a number of others. The app was released by New Endian, LLC in Septem-

ber 2011. The app is available for download and sells for about $20 on the Apple App Store and Google Play Store. The settings and values that can be changed vary from one transmitter model to another. The complete list of available tones in the app is as follows:

Input gain Frequency Sleep Mode Panel LOCK/UNLOCK RF output power Low frequency audio roll-off LEDs ON/OFF The user interface involves selecting the audio se-

quence related to the desired change. Each version has an interface for selecting the desired setting and the desired option for that setting. Each version also has a mechanism to prevent accidental activation of the tone. iOS The iPhone version keeps each available setting on a separate page with the list of options for that setting. On iOS, the Activate toggle switch must be enabled to show the button which will then activate the tone. The iOS versions default orientation is upside-down but can be configured to orient right-side up. The purpose for this is to orient the phones speaker, which is at the bot-

tom of the device, closer to the transmitter microphone. Android The Android version keeps all settings on the same page and allows the user to toggle between the activa-

tion buttons for each setting. The activation button must be pressed and held to activate the tone. The Android version also allows users to keep a configurable list of full sets of settings. Activation For a transmitter to respond to remote control audio tones, the transmitter must meet certain requirements:

The transmitter must be turned on. The transmitter must have firmware version 1.5 or later for Audio, Frequency, Sleep and Lock changes. The transmitter microphone must be within range. The remote control function must be enabled on the transmitter. Please be aware this app is not a Lectrosonics product. It is privately owned and operated by New Endian LLC, www.newendian.com. 13 Micro Body Pack TransmitterRio Rancho, NM Accessories Rechargeable battery P/N 40106-1 LB-50 3.6V lithium-ion battery pack Antenna upward belt clip P/N 27079 slide-on belt clip Battery charger kit P/N 40107 charger for Lectrosonics LB-50 battery;

includes charger, EU plug adapter and vehicle auxiliary power cord Cordura Pouch P/N 35939 zippered, padded; 4 x 6 x1 inches Antenna downward belt clip P/N 26995 slide-on belt clip Port Cover P/N P1311 Micro USB port cover 14 SSMLECTROSONICS, INC. Firmware Update Updating the firmware is a simple matter of download-

ing a utility program and file from the website and run-

ning the program on a Windows operating system with the transmitter connected to a computer via the USB port. Go to www.lectrosonics.com/US. In the top menu, hover the mouse over Support, and click on Wireless Support. On the right-hand-side Wireless Support Menu, choose Wireless Downloads. Choose your prod-

uct (SSM), then choose Firmware. Step 1:

Step 2:

Next, test the Updater by opening the icon:

driver opens automatically, proceed to Step 3. If the WARNING: If you receive the following error, the Updater is not installed on your system. Follow the TROUBLESHOOTING steps to fix the error. Begin by downloading the USB Firmware Updater Program. TROUBLESHOOTING:

If you receive the FTDI D2XX error shown above, download and install the driver by clicking on this link. Then click here to download. NOTE: This website, http://www.ftdichip.com/

Drivers/D2XX.htm, is not associated with Lectrosonics.com. It is a third party site used only for D2XX drivers currently available for Lectrosonics devices upgrades. 15 Micro Body Pack TransmitterRio Rancho, NM Step 3:

Step 7:

Refer to Step 1 to return to Firmware web page. Down-

load Firmware Update and save to a local file on your PC for easy locating when updating. In Lectrosonics USB Firmware Updater, choose the detected device, browse to local Firmware File and click Start. NOTE: It may take up to a minute or so for the Updater to recognize the transmitter. Step 4:

Open Lectrosonics USB Firmware Updater. WARNING: Do not disrupt the microUSB cable during updating. Step 5:

Step 6:

Put the transmitter in UPDATE mode by simultaneously holding down the UP and DOWN arrow buttons on the transmitter control panel while powering it up. The Updater alerts with progress and completion. Step 8:

Once the Updater has com-

pleted, turn off the transmitter, then turn it back on to verify that the firmware version on the transmitter LCD matches the firmware version shown on the web site. The firmware is the second LCD display during boot up sequence. Using a microUSB cable, connect the transmitter to your PC. Step 9:

Close Updater and disconnect microUSB cable. 16 SSMLECTROSONICS, INC. Specifications Operating Frequencies:

Band A1: 470.100 - 537.575 Band B1: 537.600 - 607.950 Frequency Selection Steps:

RF Power output:

Compatibility Modes:

Pilot tone:

Frequency Stability:

Spurious radiation:

Equivalent input noise:

Input level:

Input impedance:

Input limiter:

Gain control range:

Modulation indicators:

Audio Performance (Nu Hybrid mode) Frequency Response:

Low frequency roll-off:

THD:

SNR at receiver output:

Selectable; 100 kHz or 25 kHz Selectable; 25 or 50 mW Nu Hybrid, Mode 3, IFB 25 to 32 kHz;

3.5 kHz deviation

(Nu Hybrid mode) 0.002%

Compliant with ETSI EN 300 422-1 v1.4.2 120 dBV (A-weighted) Nominal 2 mV to 300 mV, before limiting. Greater than 1V maximum, with limiting. Mic: 300 or 4.5 k ohm;

selectable Line: greater than 100 k ohm DSP controlled, dual envelope soft limiter with greater than 30 dB range 44 dB; digital control Dual bicolor LEDs indicate modulation of -20, -10, 0 and

+10 dB referenced to full modulation 70 Hz to 20 kHz (+/-1dB) 12 dB/octave; 70 Hz 0.2% (typical) No Limiting w/Limiting 103.5 107.0 108.5 108.0 111.5 113.0 SmartNR OFF NORMAL FULL Note: The dual envelope soft limiter provides exceptionally good handling of transients using variable attack and release time constants. Once activated, the limiter compresses 30+ dB of transmitter input range into 4.5 dB of receiver output range, thus reducing the measured figure for SNR without limiting by 4.5 dB Controls:

Audio Input Jack:

Antenna:

Battery:

Battery Life:

Weight:

Dimensions (housing):

Emission Designator:

Side panel membrane switches with LCD interface f or power on/off and all setup and configuration controls LEMO 00 Series 3-pin Galvanized steel, flexible wire Lithium-ion 3.6 V 1000 mAH NP50 battery pack 6 hours per charge 2.3 ounces (65.2 grams) including lithium battery pack 2.3 x 1.5 x .56 in. (58.4 x 38 x 14.2 mm) 110KF3E Specifications subject to change without notice. 17 Micro Body Pack TransmitterRio Rancho, NM Service and Repair If your system malfunctions, you should attempt to correct or isolate the trouble before concluding that the equipment needs repair. Make sure you have followed the setup procedure and operating instructions. Check the interconnect-

ing cables. We strongly recommend that you do not try to repair the equipment yourself and do not have the local repair shop attempt anything other than the simplest repair. If the repair is more complicated than a broken wire or loose connec-

tion, send the unit to the factory for repair and service. Dont attempt to adjust any controls inside the units. Once set at the factory, the various controls and trimmers do not drift with age or vibration and never require readjustment. There are no adjustments inside that will make a malfunctioning unit start working. LECTROSONICS Service Department is equipped and staffed to quickly repair your equipment. In warranty repairs are made at no charge in accordance with the terms of the warranty. Out-of-warranty repairs are charged at a modest flat rate plus parts and shipping. Since it takes almost as much time and effort to determine what is wrong as it does to make the repair, there is a charge for an exact quotation. We will be happy to quote approximate charges by phone for out-of-warranty repairs. Returning Units for Repair For timely service, please follow the steps below:

A. DO NOT return equipment to the factory for repair without first contacting us by e-mail or by phone. We need to know the nature of the problem, the model number and the serial number of the equipment. We also need a phone number where you can be reached 8 A.M. to 4 P.M. (U.S. Mountain Standard Time). B. After receiving your request, we will issue you a return authorization number (R.A.). This number will help speed your repair through our receiving and repair departments. The return authorization number must be clearly shown on the outside of the shipping container. C. Pack the equipment carefully and ship to us, shipping costs prepaid. If necessary, we can provide you with the proper packing materials. UPS or FEDEX is usually the best way to ship the units. Heavy units should be dou-

ble-boxed for safe transport. D. We also strongly recommend that you insure the equipment, since we cannot be responsible for loss of or damage to equipment that you ship. Of course, we insure the equipment when we ship it back to you. Lectrosonics USA:

Mailing address:

Lectrosonics, Inc. PO Box 15900 Rio Rancho, NM 87174 USA Web:

www.lectrosonics.com Lectrosonics Canada:

Mailing Address:

720 Spadina Avenue, Suite 600 Toronto, Ontario M5S 2T9 Telephone:

+1 (505) 892-4501

(800) 821-1121 Toll-free US and Canada Fax +1 (505) 892-6243 Shipping address:

Lectrosonics, Inc. 561 Laser Rd., Suite 102 Rio Rancho, NM 87124 USA E-mail:

service.repair@lectrosonics.com sales@lectrosonics.com Telephone:

+1 (416) 596-2202

(877) 753-2876 Toll-free Canada

(877) 7LECTRO Fax (416) 596-6648 E-mail:

Sales: colinb@lectrosonics.com Service: joeb@lectrosonics.com 18 SSMLECTROSONICS, INC. 19 Micro Body Pack TransmitterRio Rancho, NM LIMITED ONE YEAR WARRANTY The equipment is warranted for one year from date of purchase against defects in materials or workmanship provided it was purchased from an authorized dealer. This warranty does not cover equipment which has been abused or damaged by careless handling or shipping. This warranty does not apply to used or demonstrator equipment. Should any defect develop, Lectrosonics, Inc. will, at our option, repair or replace any defective parts without charge for either parts or labor. If Lectrosonics, Inc. cannot correct the defect in your equipment, it will be replaced at no charge with a similar new item. Lectrosonics, Inc. will pay for the cost of returning your equipment to you. This warranty applies only to items returned to Lectrosonics, Inc. or an authorized dealer, shipping costs prepaid, within one year from the date of purchase. This Limited Warranty is governed by the laws of the State of New Mexico. It states the entire liablility of Lectrosonics Inc. and the entire remedy of the purchaser for any breach of warranty as outlined above. NEITHER LECTROSONICS, INC. NOR ANYONE INVOLVED IN THE PRODUCTION OR DELIVERY OF THE EQUIPMENT SHALL BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, CONSEQUENTIAL, OR INCIDENTAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THIS EQUIPMENT EVEN IF LECTROSONICS, INC. HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL THE LIABILITY OF LECTROSONICS, INC. EXCEED THE PURCHASE PRICE OF ANY DEFECTIVE EQUIPMENT. This warranty gives you specific legal rights. You may have additional legal rights which vary from state to state. 581 Laser Road NE Rio Rancho, NM 87124 USA www.lectrosonics.com

(505) 892-4501 (800) 821-1121 fax (505) 892-6243 sales@lectrosonics.com 19 October 2018