Test Report No.: GETEC-E3-05-081 FCC Class B Certification APPENDIX H
: USERS MANUAL EUT Type: 37 LCD TV/ Monitor FCC ID: BEJ37LDD LCD TV MODELS: 32LC2D 37LC2D 42LC2D PLASMA TV MODELS: 42PC3D 42PC3DV 50PC3D 42PC3D-UD 42PC3DV-UD 50PC3D-UD OWNERS MANUAL Internet Home Page : http://www.lge.com http://www.lg.ca Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service. P/NO : 3828TUL527A (0511-REV00) Printed in Korea Warning WWarning arning CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of suffi-
cient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appli-
ance. NOTE TO CABLE/TV INSTALLER:
This reminder is provided to call the CATV system installers attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as prac-
tical. REGULATORY INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. CAUTION:
Do not attempt to modify this product in any way without written authorization from LG Electronics Corporation. Unauthorized modification could void the users authority to operate this product. U.S.A. only -----------------------------------------------
COMPLIANCE:
The responsible party for this products compliance is:
LG Electronics U.S.A., Inc. 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 Phone: 1-201-816-2000 http://www.lgusa.com
Safety Instructions Safety Instructions Safety Instructions WARNING :
To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Apparatus To Rain Or Moisture. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. Owner's Manual 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience recepta-
cles, and the point where they exit from the apparatus. 7. Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions. 11. Only use the attachments / accessories specified by the manufacturer. Safety Instructions 12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the appa-
ratus. When a cart is used, use caution when moving the cart / apparatus combination to avoid injury from tip-over. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normal-
ly, or has been dropped. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. Note
- If the TV feels cold to the touch, there may be a small flicker when when it is turned on. This is normal, there is noth-
ing wrong with TV.
- Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance.
- Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen. CAUTION concerning the Power Cord Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discon-
tinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. On Disposal a. The fluorescent lamp used in this product contains a small amount of mercury. b. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority. Introduction Controls (Model Name: 32/37/42LC2D)
(Model Name: 32/37/42LC2D) Controls
- This is a simplified representation of front panel.
- Here shown may be somewhat different from your TV. CH VOLVOL ENTER ENTER MENUMENU INPUT INPUT ON/OFF ON/OFF CHANNEL Buttons VOLUME Buttons ENTER Button MENU Button INPUT Button ON/OFF Button R Remote Control Sensor Power/Standby Indicator illuminates red in standby mode. illuminates green when the set is switched on. Connection Options (Model Name: 32/37/42LC2D) Connection Options (Model Name: 32/37/42LC2D)
- Here shown may be somewhat different from your TV. Introduction AC IN S-VIDEO Input AUDIO Input VIDEO Input S-VIDEO S-VIDEO R AUDIO AUDIO L/L/MONOMONO VIDEO VIDEO AV IN 2 AV IN 2 AV OUT AV OUT AV OUT AV IN1 COMPONENT IN 1/2 VIDEO VIDEO
) MONO AUDIO AUDIO AV IN 1 AV IN 1 S-VIDEO S-VIDEO VIDEO VIDEO COMPONENT IN COMPONENT IN AUDIO AC IN AC IN HDMI / DVI IN RS-232C INPUT
(CONTROL&SERVICE) HDMI/DVI IN HDMI/DVI IN DIGITAL AUDIO OUT DIGITAL AUDIO OUT OPTICAL OPTICAL RS-232C IN RS-232C IN
(CONTROL&SERVICE)
(CONTROL SERVICE) CABLE IN ANTENNA IN DIGITAL AUDIO OUT OPTICAL ANTENNA ANTENNA IN CABLE CABLE IN AUDIO IN AUDIO IN
(RGB/DVI)
(RGB/DVI) REMOTE CONTROL RGB IN RGB IN
(PC(PC/DTV)DTV) AUDIO IN
(RGB/DVI) RGB IN
(PC/DTV) REMOTE CONTROL Port Installation Installation Installation The TV can be installed in various ways such as on a wall, or on a desktop etc. The TV is designed to be mounted horizontally. GROUNDING Ensure that you connect the earth ground wire to prevent pos-
sible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes. Power Supply Short-circuit Breaker Desktop Pedestal Installation For proper ventilation, allow a clearance of 4" on each side and from the wall. 4 inches 4 inches 4 inches 4 inches 4 inches 4 inches 4 inches 4 inches Installation How to join the product assembly to the wall to protect the set tumbling
- Set it up close to the wall so the product doesnt fall over when it is pushed backwards.
- The instructions shown below is a safer way to set up the product, which is to fix it on the wall so the prod-
uct doesnt fall over when it is pulled in the forward direction. It will prevent the product from falling for-
ward and hurting people. It will also prevent the product from damage caused by fall. Please make sure that children dont climb on or hang from the product. 42PC3D/42PC3DV/50PC3D 1 2 3 4 5 If the set will be mounted on a desk top, insert the 2 eye-bolts and tighten them securely in the upper holes as shown. Install the wall brackets on the wall with 2 bolts*, (not supplied with the product), as shown. Match the height of the eye-bolts and the wall brackets. Check to be sure the eye-bolts and the brackets are tightened securely. Secure the TV assembly to the wall with strong strings or wire cables, (not supplied with the product), as shown. 32/37/42LC2D 1 2 3 1 2 3 Use the bracket and the bolt to fix the product to the wall as shown in the picture. Secure the bracket with the bolt (not provided as parts of the product, must purchase separately) on the wall. Use a sturdy rope (not provided as parts of the product, must purchase separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product. Notes When moving the product to another place undo the ropes first. Use a product holder or a cabinet that is big and strong enough for the size and weight of the product. To use the product safely make sure that the height of the bracket that is mounted on the wall is same as that of the product. Installation
- The TV has a special signal output capability which allows you to hook up a second TV or monitor. Monitor Out Setup AV OUT VIDEO VIDEO
) MONO AUDIO AV IN 1 S-VIDEO VIDEO VIDEO COMPONENT IN AUDIOUDIO 1 2 Connect the second TV or monitor to the TVs AV OUTPUT jacks. See the Operating Manual of the second TV or monitor for further details regarding that devices input settings. 1/2 S-VIDEO IN
(R) AUDIO (L) VIDEO Component RGB-PC/RGB-DTV, HDMI/DVI, DTV input sources cannot be used for Monitor out. 1-2, When connecting with external audio equip-
ments, such as amplifiers or speakers, please turn the TV speakers off. (Refer to p.43) We recommend to use the video and audio output jacks for VCR recording.
- Send the TVs audio to external audio equipment (stereo system) via the Digital Audio Output Optical port. Digital Audio Output HDMI/DVI IN DIGITAL AUDIO OUT OPTICAL RS-232C IN RS-232C IN
(CONTROL&SERVICE) 1/2 1 2 3 Connect one end of an optical cable to the TV Digital Audio Optical Output port. Connect the other end of the optical cable to the digital audio optical input on the audio equipment. See the external audio equipment instruction manual for operation. When connecting with external audio equip-
ments, such as amplifiers or speakers, please turn the TV speakers off. CAUTION Do not look into the optical output port. Looking at the laser beam may damage your vision.
- This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. When connecting with a D-sub 15 pin cable PC Setup Installation AUDIO IN AUDIO IN
(RGB/DVI) REMOTE CONTROL RGB IN
(PC/DTV) 2 1
(R) AUDIO (L) RGB-PC OUTPUT PC 1 2 3 4 Connect the RGB output of the PC to the RGB IN
(PC/DTV)
/ RGB
(PC/DTV) (42PC3D/3DV/50PC3D Model) jack on the set.
(32/37/42LC2D Model) Connect the PC audio outputs to the AUDIO IN
(RGB/DVI)
/AUDIO
(RGB/DVI) (42PC3D/3DV/50PC3D Model) jack on the set.
(32/37/42LC2D Model) Turn on the PC and the set. Select RGB-PC input source with using the TV/VIDEO button on the remote control. When connecting with a HDMI to DVI cable HDMI/DVI IN DIGITAL AUDIO OUT OPTICAL RS-232C IN RS-232C IN
(CONTROL&SERVICE) 1 ANTENNA IN CABLE IN AUDIO IN AUDIO IN
(RGB/DVI) REMOTE CONTROL RGB IN
(PC/DTV) 2 DVI-PC OUTPUT
(R) AUDIO (L) PC 1 2 3 4 Connect the DVI output of the PC to the HDMI/DVI IN jack on the set. Connect the audio outputs of the PC to the AUDIO IN (RGB/DVI) (32/37/42LC2D Model)
/AUDIO (RGB/DVI) (42PC3D/3DV/50PC3D Model) jack on the set. Turn on the PC and the set. Select HDMI/DVI input source with using the TV/VIDEO button on the remote control. If the PC has a DVI output and no HDMI output, a separated audio connection is necessary. If the PC does not support Auto DVI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of PC graphics card's output resolution to 1024x768, 60Hz. Installation 1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60Hz. 2. Depending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use. 3. When Source Devices connected with HDMI1/DVI Input, output PC Resolution (VGA, SVGA, XGA), Position and Size may not fit to Screen.Press the ADJUST button to adjust the screen Position of TV SET and contact an PC graphics card service cen-
ter. 4. When Source Devices connected with HDMI/DVI Input, output TV SET Resolution (480p, 720p, 1080i) and TV SET Display fit EIA/CEA-861-B Specification to Screen. If not, refer to the Manual of HDMI/DVI Source Devices or contact your ser-
vice center. In case HDMI/DVI Source Devices is not connect-
ed Cable or poor cable connection, "NO SIGNAL"
OSD display in HDMI1/DVI Input. In case that Video Resolution is not supported TV SET output in HDMI/DVI Source Devices, "INVALID FORMAT"
5. OSD display. Refer to the Manual of HDMI1/DVI Source Devices or contact your service center. 6. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC, HDMI/DVI mode. If noise is present, change the PC or HDMI/DVI mode to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card. 7. Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become permanently imprinted on the screen. 8. The synchronization input form for Horizontal and Vertical frequencies is separate. Supported Display Resolution
(RGB-PC, HDMI/DVI Mode) Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz)
* 640x350
* 720x400 640x480 31.468 31.469 31.469 37.861 37.500
* RGB-PC only 70.09 70.08 59.94 72.80 75.00 800x600 1024x768 35.156 37.879 48.077 46.875 48.363 56.476 60.023 56.25 60.31 72.18 75.00 60.00 70.06 75.02 30 Installation Screen Setup for PC mode
- When RGB connect to PC input and select the RGB-PC, this function is used.
- When HDMI/DVI connect to PC input and select HDMI/DVI input, this function is used.
- In RGB-DTV mode, SIZE and PHASE is not available.
- After connecting RGB-PC or HDMI/DVI to PC input and checking the screen quality.
* Adjustment for screen Position, Size, and Phase POSITION G SIZE PHASE RESET Adjust Close F D E G 1 2 3 Press the ADJUST button and then use D / E button to select POSITION, SIZE, or PHASE. Press ENTER button and then use D / E / F / G buttons to make appropriate adjustments. The PHASE adjustment range is -16 ~ +16.
(In HDMI/DVI-PC mode, PHASE is not available.) The SIZE adjustment range is -50 ~ +50. Press ENTER button. Mini Glossary Size Position This function is to adjust picture to left/right and up/down as you prefer. This function is to mini-
mize any vertical bars or stripes visible on the screen background. And the horizontal screen size will also change. This function allows you to remove any horizontal noise and clear or sharpen the image of characters. Phase
* Initializing (Reset to original factory values) Initialize Settings POSITION SIZE PHASE RESET G Adjust Close
- To initialize the adjusted values 1 2 3 Press the ADJUST button and then use D / E button to select the RESET option. Press ENTER button and then use F / G button to select Yes. Press ENTER button. Reference External Control Device Setup External Control Device Setup
- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the Monitors functions externally.
- Connect the serial port of the control device to the RS-232C jack on the TV back panel.
- RS-232C connection cables are not supplied with the TV. RS-232C Setup RS-232C Setup HDMI/DVI IN DIGITAL AUDIO OUT OPTICAL RS-232C IN
(CONTROL&SERVICE) PC TType of Connector; D-Sub 9-Pin Male ype of Connector; D-Sub 9-Pin Male No. Pin Name 1 2 3 4 5 6 7 8 9 No connection RXD (Receive data) TXD (Transmit data) DTR (DTE side ready) GND DSR (DCE side ready) RTS (Ready to send) CTS (Clear to send) No Connection RS-232C Configurations RS-232C Configurations 1 5 9 6 7-Wire Configurations
(Serial female-female NULL modem cable) 3-Wire Configurations
(Not standard) PC 2 3 5 4 6 7 8 RXD TXD GND DTR DSR RTS CTS TV 3 2 5 6 4 8 7 TXD RXD GND DSR DTR CTS RTS PC 2 3 5 4 6 7 8 RXD TXD GND DTR DSR RTS CTS TV 3 2 5 4 6 7 8 TXD RXD GND DTR DSR RTS CTS D-Sub 9 D-Sub 9 D-Sub 9 D-Sub 9 Set ID Set ID
- Use this function to specify a TV ID number.
- Refer to Real Data Mapping. See page 56. 1. Press the MENU button and then use D / E button to select the SETUP menu. 2. Press the G button and then use D / E button to select Set ID. 3. Press the G button and then use D / E button to adjust Set ID to choose the desired TV ID number. The adjustment range of Set ID is 1 ~ 99. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Communication Parameters Communication Parameters Baud rate : 9600 bps (UART) Data length : 8 bits Parity : None Stop bit : 1 bit Communication code : ASCII code Reference EZ Scan Manual Scan Channel Edit DTV Signal Input Source Input Label Set ID SETUP G VIDEO AUDIO TIME OPTION LOCK MENU Previous G 1 TTransmission / Receiving Protocol ransmission / Receiving Protocol Transmission
* Use a crossed (reverse) cable.
[Command1][Command2][ ][Set ID][ ][Data][Cr]
Command Reference List Command Reference List COMMAND 1 COMMAND 2 DATA
(Hexadecimal) 01. Power k 02. Input Select k 03. Aspect Ratio k 04. Screen Mute k 05. Volume Mute k 06. Volume Control k 07. Contrast k 08. Brightness k 09. Color k 10. Tint k 11. Sharpness k 12. OSD Select k 13. Remote Control Lock Mode k k 14. Treble k 15. Bass 16. Balance k k 17. Color Temperature j 18. ISM Method j 19. Low Power j 20. Orbiter Time Setting 21. Orbiter Pixel Setting j 0 ~ 1 0 ~ 8 0 ~ 1 0 ~ 1 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 1 0 ~ 1 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 2 a b c * (Refer to p.56) d e f g h i j k l m r s t u p * (Refer to p.58) q r s 0 ~ 1 1 ~ FE 1 ~3
* Command 18~21: 42PC3D/3DV, 50PC3D models only
* [Command 1]: First command to control the set.(j,k,m or x)
* [Command 2]: Second command to control the set.
* [Set ID]: You can adjust the set ID to choose desired monitor ID number in Setup menu. Adjustment range is 1
~ 99. When selecting Set ID 0, every connected the TV is controlled. Set ID is indicated as decimal
(1~99) on menu and as Hexa decimal (0x0~0x63) on transmission/receiving protocol.
* [DATA]: To transmit command data. Transmit FF data to read status of command.
* [Cr]: Carriage Return ASCII code 0x0D
* [ ]: ASCII code space (0x20) OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The Monitor transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer. Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The Monitor transmits ACK (acknowledgement) based on this format when receiving abnormal data from non-viable functions or communication errors. Data 1: Illegal Code 2: Not supported function 3: Wait more time COM-
MAND 1 COM-
MAND 2 DATA 0 DATA 1 DATA 2 DATA 3 DATA 4 DATA 5
(Hexadecimal)
(Hexadecimal)
(Hexadecimal) a physical/program high major/program low major low minor high minor low attribute b 00 ~ 01 c key code
(Hexadecimal)
(Hexadecimal)
(Hexadecimal) 22. Channel Tuning m 23. Channel Add/Del m 24. Key m 25. Input Select x b *(Refer to p.59) Reference Maintenance Maintenance
- Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning. Cleaning the Screen Cleaning the Screen 1. Heres a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until its almost dry, and then use it to wipe the screen. 2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV. Cleaning the Cabinet Cleaning the Cabinet To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please be sure not to use a wet cloth. Extended Absence Absence Extended If you expect to leave your TV dormant for a long time (such as a vacation), its a good idea to unplug the power cord to protect against possible damage from lightning or power surges. Product Specifications Product Specifications MODEL 32LC2D 37LC2D 42LC2D Power requirement AC100-240V ~ 50/60Hz 1.5A AC100-240V ~ 50/60Hz 2.0A AC100-240V ~ 50/60Hz 2.5A Television System Program Coverage External Antenna Impedance Operating Temperature Range Operating Humidity Range NTSC-M, ATSC, 64 & 256 QAM VHF 2 ~ 13, UHF 14 ~ 69, CATV 1 ~ 135, CADTV 1 ~ 135, DTV 2 ~ 69 75 32 ~ 104F (0 ~ 40C) Less than 80%
MODEL 42PC3D/3DV-UD 50PC3D-UD Power requirement Television System Program Coverage External Antenna Impedance Operating Temperature Range Operating Humidity Range Resolution AC100-240V ~ 50/60Hz 2.0A NTSC-M, ATSC, 64 & 256 QAM VHF 2 ~ 13, UHF 14 ~ 69, CATV 1 ~ 135, CADTV 1 ~ 135, DTV 2 ~ 69 75 32 ~ 104F (0 ~ 40C) Less than 80%
852 x 480 (Dot) 1366 x 768 (Dot) The specifications shown above may be changed without prior notice for quality improvement.