Test Report No.: GETEC-E3-05-031 FCC Class B Certification APPENDIX H
: USERS MANUAL EUT Type: 42 LCD TV/Monitor FCC ID : BEJ42LDA LCD TV OWNERS MANUAL MODELS: 26LX1D 32LX1D 26LX2D 32LX2D 32LP1D 37LP1D 42LP1D Internet Home Page : http://www.lge.com http://www.lg.ca Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service. TM P/NO : 3828TUL309D (0503-REV00) Printed in Korea Warning WWarning arning CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of suffi-
cient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appli-
ance. NOTE TO CABLE/TV INSTALLER:
This reminder is provided to call the CATV system installers attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as prac-
tical. REGULATORY INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. CAUTION:
Do not attempt to modify this product in any way without written authorization from LG Electronics Corporation. Unauthorized modification could void the users authority to operate this product. U.S.A. only -----------------------------------------------
COMPLIANCE:
The responsible party for this products compliance is:
LG Electronics U.S.A., Inc. 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 Phone: 1-201-816-2000 http://www.lgusa.com
Introduction Controls (Model Name: 32/37/42LP1D)
(Model Name: 32/37/42LP1D) Controls
- This is a simplified representation of front panel.
- Here shown may be somewhat different from your TV. Logo Display Lamp 1394 IEEE Channel Display Power Standby Indicator Illuminates red when the TV is in standby mode. When the TV is switched on, blinks green and then illuminates green. DTV, CADTV mode TV, CATV, DTV, CADTV mode Video1-2 mode Component1-2 mode PC mode HDMI mode 1394 IEEE IEEE1394 Stereo mode mode Remote Control Sensor CH VOL MENU TV/VIDEO/
TV GUIDE ON/OFF RR AUDIO AUDIO L/MONO L/MONO IN2 VIDEO S-VIDEO VIDEO S-VIDEO Memory Card Slot
(For mode) ON/OFF Button TV GUIDE Button CHANNEL (E, D) Buttons MENU Button Audio/Video Input 2 TV/VIDEO / Button S-VIDEO Input VOLUME (F,G) Buttons Introduction Connection Options (Model Name: 32/37/42LP1D) Connection Options (Model Name: 32/37/42LP1D) COMPONENT2 O E D V I COMPONENT2
(VIDEO / AUDIO Input) I O D U A L R AC IN G-LINKTM Port DIGITAL AUDIO OUTPUT
/ DVI INPUT
/ COMPONENT1 INPUT MONITOR OUT HDMI / IEEE1394 Port AUDIO/VIDEO INPUT1 CableCARDTM Slot AC IN HDMI CableCARD G-LINK DIGITAL AUDIO
(OPTICAL) R AUDIO (MONO) L VIDEO S-VIDEO REMOTE CONTROL RS-232C INPUT
(CONTROL/SERVICE) OUTPUT DVI INPUT COMPONENT1 IEEE 1394 MONITOR OUT VIDEO1 CABLE PC AUDIO INPUT RGB INPUT
(PC/DTV INPUT) COMPONENT1 INPUT R L AUDIO INPUT VIDEO INPUT ANTENNA RS-232C INPUT (CONTROL/SERVICE) /
RGB INPUT (PC/DTV INPUT) ANTENNA Input CABLE Input PC AUDIO INPUT REMOTE CONTROL Port COMPONENT1 (VIDEO / AUDIO INPUT)
* The HDMI port can receive video via High-Definition Multimedia Interface (HDMI) or the Digital Visual Interface
(DVI). Note: An adapter or special cable is required to plug DVI into an HDMI port (available at home theater or computer stores). Installation External Equipment Connections External Equipment Connections Antenna or Cable Connection Analog and Digital TV signals provided on antenna
- Antenna or Cable Service without a Cable Box Connection.
- For optimum picture quality, adjust antenna direction if needed. Multi-family Dwellings/Apartments
(Connect to wall antenna socket) Wall Antenna Socket RF Coaxial Wire (75 ohm) ANTENNA VHF Antenna UHF Antenna Turn clockwise to tighten. Outdoor Antenna Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna) Be careful not to bend the bronze wire when connecting the antenna. Bronze Wire Analog and Digital TV signals provided on cable Cable TV Wall Jack RF Coaxial Wire (75 ohm) Turn clockwise to tighten. Analog and Digital TV signals provided on cable and antenna Cable TV Wall Jack RF Coaxial Wire (75 ohm) Bronze Wire Antenna RF Coaxial Wire (75 ohm) Turn clockwise to tighten. Bronze Wire CABLE CABLE ANTENNA ANTENNA signal amplifier In a poor signal area to improve picture quality, purchase and install a sig-
nal amplifier. If the antenna needs to be split for two TVs, install a 2-Way Signal Splitter in the connections. If the antenna is not installed properly, contact your dealer for assistance. 21 Installation NOTE: All cables shown are not included with the TV. VCR Setup
- To avoid picture noise (interference), leave an adequate distance between the VCR and TV.
- Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen. When connecting with an antenna 32, 37, 42 inch TV Back R AUDIO (MONO) L VIDEO S-VIDEO MONITOR OUT VIDEO1 CABLE COMPONENT1 R L AUDIO INPUT VIDEO INPUT ANTENNA 1 2 ANT IN ANT OUT S-VIDEO OUT OUTPUT SWITCH 3 4
(R) AUDIO (L) VIDEO IN VCR 26 inch TV Back CableCARD HDMI IEEE 1394 COMPONENT1 T U P N I O E D V I L R T U P N I I O D U A 2 ANT IN ANT OUT S-VIDEO OUT OUTPUT SWITCH 3 4
(R) AUDIO (L) VIDEO IN CABLE ANTENNA 1 VCR 1 2 3 4 Connect the RF antenna out socket of the VCR to the Antenna socket on the set. Connect the antenna cable to the RF antenna in socket of the VCR. Set VCR output switch to 3 or 4 and then tune TV to the same channel number. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owners manual.) When connecting with a RCA cable 32, 37, 42 inch TV Back R AUDIO (MONO) L VIDEO S-VIDEO MONITOR OUT VIDEO1 COMPONENT1 R L AUDIO INPUT VIDEO INPUT 1 ANT IN ANT OUT S-VIDEO OUT OUTPUT SWITCH 3 4
(R) AUDIO (L) VIDEO IN VCR 26 inch TV Back OUTPUT DVI INPUT COMPONENT1 INPUT HDMI IEEE 1394 COMPONENT1 DIGITAL AUDIO
(OPTICAL) O E D V S
I O E D V I
) O N O M
L I O D U A R 1 O E D V I T U P N I O E D V I L R T U P N I I O D U A 1 ANT IN ANT OUT S-VIDEO OUT VCR OUTPUT SWITCH 3 4
(R) AUDIO (L) VIDEO IN 1 2 3 Connect the AUDIO/VIDEO jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left
= white, and Audio Right = red) Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owners manual.) Select Video1 input source using the TV/VIDEO button on the remote control.
- If connected to IN2 (or VIDEO2), select Video2 input source. If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO jack of the set. NOTE: All cables shown are not included with the TV DVD Setup When connecting with a S-Video cable 32, 37, 42 inch TV Back R AUDIO (MONO) L VIDEO S-VIDEO MONITOR OUT VIDEO1 COMPONENT1 R L AUDIO INPUT VIDEO INPUT 1 2 DVD S-VIDEO
(R) AUDIO (L) 26 inch TV Back DIGITAL AUDIO
(OPTICAL) O E D V S
I OUTPUT DVI INPUT O E D V I
) O N O M
L I O D U A R 1 O E D V I T U P N I O E D V I COMPONENT1 INPUT HDMI IEEE 1394 COMPONENT1 L R T U P N I I O D U A 1 2 DVD
(R) AUDIO (L) S-VIDEO 1 2 3 4 5 Connect the S-VIDEO output of the DVD to the S-VIDEO input on the set. Connect the audio outputs of the DVD to the AUDIO input jacks on the set. Turn on the DVD player, insert a DVD. Select Video1 input source with using the TV/VIDEO button on the remote control.
- If connected to IN2 (or VIDEO2), select Video 2 input source. Refer to the DVD player's manual for operating instructions. When connecting with a HDMI cable 32, 37, 42 inch TV Back 26 inch TV Back HDMI CableCARD IEEE 1394 1 CABLE ANTENNA CableCARD HDMI IEEE 1394 COMPONENT1 1 T U P N I O E D V I L R T U P N I I O D U A HDMI-DVD OUPUT DVD HDMI-DVD OUPUT DVD 1 2 3 Connect the HDMI output of the DVD to the HDMI jack on the set. Select HDMI TV/VIDEO button on the remote control. input source with using the Refer to the DVD player's manual for operating instructions. TV can receive the video and audio signal simulta-
neously with using a HDMI cable. If the DVD supports Auto HDMI function, the DVD output resolution will be automatically set to 1280x720p. If the DVD does not support Auto HDMI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the DVD to 1280x720p. When connecting with a component cable 32, 37, 42 inch TV Back DIGITAL AUDIO
(OPTICAL) OUTPUT S-VIDEO R AUDIO (MONO) L VIDEO MONITOR OUT VIDEO1 RS-232C INPUT
(CONTROL/SERVICE) DVI INPUT COMPONENT1 RGB INPUT
(PC/DTV INPUT) COMPONENT1 INPUT R L AUDIO INPUT VIDEO INPUT 2-2 2-1 1 26 inch TV Back HDMI IEEE 1394 COMPONENT1 1 O E D V I T U P N I O E D V I L R T U P N I I O D U A 2-1 DIGITAL AUDIO
(OPTICAL) OUTPUT DVI INPUT COMPONENT1 INPUT 2-2 O E D V S
I O E D V I
) O N O M
L I O D U A R 1
(R) AUDIO (L) B R B R
(R) AUDIO (L) DVD DVD Select or , depending on your DVD connector. 2-2 2-1 1 Connect the video outputs (Y, PB, PR) of the DVD to the COMPONENT1 VIDEO INPUT jacks on the set. 2-1 Connect the audio outputs of the DVD to the COMPONENT1 AUDIO INPUT jacks on the set. 2-2 Connect the optical audio output of the DVD to the DIGITAL AUDIO COMPONENT1 INPUT jack on the set. 3 4 5 Turn on the DVD player, insert a DVD. Select Component 1 input source with using the TV/VIDEO button on the remote control.
- If connected to COMPONENT2 input, select Component 2 input source. Refer to the DVD player's manual for operating instructions. Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below. Component ports on the TV Video output ports on DVD player Y Y Y Y Y PB Pb B-Y Cb PB PR Pr R-Y Cr PR Digital Audio will not work for Component 2 input source. Digital Audio operation has priority if Digital Audio and AUDIO L/R are connected at the same time. 25 Installation HDSTB Setup
- This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below. When connecting with a D-sub 15 pin cable 32, 37, 42 inch TV Back 26 inch TV Back AC IN G-LINK DIGITAL AUDIO
(OPTICAL) REMOTE CONTROL RS-232C INPUT
(CONTROL/SERVICE) OUTPUT DVI INPUT AC IN G-LINK OUTPUT REMOTE CONTROL RS-232C INPUT
(CONTROL/SERVICE) DVI INPUT PC AUDIO INPUT RGB INPUT
(PC/DTV INPUT) COMPONENT1 INPUT PC AUDIO INPUT RGB INPUT
(PC/DTV INPUT) COMPONENT1 INPUT 2 1 2 1 DIGITAL AUDIO
(OPTICAL) O E D V S
I 1 O E D V I O E D V I
) O N O M
L I O D U A R
(R) AUDIO (L) RGB-DTV OUPUT Digital Set-top Box
(R) AUDIO (L) RGB-DTV OUPUT Digital Set-top Box 1 2 3 4 Connect the RGB output of the digital set-top box to the RGB INPUT (PC/DTV INPUT) jack on the set. Connect the audio outputs of the set-top box to the PC AUDIO INPUT jack on the set. Turn on the digital set-top box. (Refer to the owners manual for the digital set-top box.) Select RGB-DTV input source with using the TV/VIDEO button on the remote control. Installation When connecting with a HDMI cable 32, 37, 42 inch TV Back 26 inch TV Back HDMI CableCARD IEEE 1394 1 CABLE ANTENNA CableCARD HDMI IEEE 1394 1 COMPONENT1 T U P N I O E D V I L R T U P N I I O D U A HDMI-DTV OUPUT Digital Set-top Box Digital Set-top Box HDMI-DTV OUPUT 1 2 3 Connect the HDMI output of the digital set-top box to the HDMI jack on the set. Select HDMI/DVI input source with using the TV/VIDEO button on the remote control. Turn on the digital set-top box. (Refer to the owners manual for the digital set-top box.) TV can receive the video and audio signal simultaneously with using a HDMI cable. If the digital set-top box supports Auto HDMI function, output resolution of the digital set-top box will be auto-
matically set to 1280x720p. If the digital set-top box does not support Auto HDMI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the digital set-top box to 1280x720p. When connecting with a HDMI to DVI cable 32, 37, 42 inch TV Back 26 inch TV Back HDMI IEEE 1394 G-LINK DIGITAL AUDIO
(OPTICAL) R AUDIO (MONO) L VIDEO S-VIDEO REMOTE CONTROL RS-232C INPUT
(CONTROL/SERVICE) OUTPUT DVI INPUT COMPONENT1 MONITOR OUT VIDEO1 CABLE G-LINK OUTPUT REMOTE CONTROL RS-232C INPUT
(CONTROL/SERVICE) DVI INPUT PC AUDIO INPUT RGB INPUT
(PC/DTV INPUT) COMPONENT1 INPUT R L AUDIO INPUT VIDEO INPUT ANTENNA PC AUDIO INPUT RGB INPUT
(PC/DTV INPUT) COMPONENT1 INPUT 2-1 2-2 1 2-1 DIGITAL AUDIO
(OPTICAL) O E D V S
I O E D V I
) O N O M
L I O D U A R 2-2 Installation HDMI IEEE 1394 COMPONENT1 L R T U P N I I O D U A 1 O E D V I T U P N I O E D V I 1
(R) AUDIO (L) DIGITAL AUDIO OPTICAL DVI-DTV OUTPUT
(R) AUDIO (L) DIGITAL AUDIO OPTICAL DVI-DTV OUTPUT Digital Set-top Box Digital Set-top Box Select or , depending on your digital set-top box connector. 2-1 2-2 1 Connect the DVI output of the digital set-top box to the HDMI jack on the set. 2-1 Connect the audio output of the digital set-top box to the PC AUDIO INPUT jack on the set. 2-2 Connect the optical audio output of the digital set-top box to the DIGITAL AUDIO DVI INPUT jack on the set. 4 5 Turn on the digital set-top box. (Refer to the owners manual for the digital set-top box.) Select HDMI/DVI input source with using the TV/VIDEO button on the remote control. If the digital set-top box has a DVI output and no HDMI output, a separated audio connection is necessary. If the digital set-top box supports Auto DVI function, the output resolution of the digital set-top box will be auto-
matically set to 1280x720p. If the digital set-top box does not support Auto DVI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the digital set-top box to 1280x720p. Installation External AV Source Setup S-VIDEO O E D V I L
) O N O M
R 2 O E D V I 2 T N E N O P M O C I O D U A O E D V I TV Side 1 2 3 Connect the AUDIO/VIDEO jacks between TV and external equipment. Match the jack colors
(Video = yellow, Audio Left = white, and Audio Right = red). Select Video2 input source with using the TV/VIDEO button on the remote control.
- If connected to VIDEO1 input, select Video1 input source. Operate the corresponding external equipment. Refer to external equipment operating guide. For connection instructions to operate the TV Guide On Screen system, see page 42~43. 1 Camcorder Video Game Set R AUDIO L VIDEO
- Send the TVs audio to external audio equipment (stereo system) via the Digital Audio Output Optical port. Digital Audio Output 32, 37, 42 inch TV Back 26 inch TV Back AC IN G-LINK DIGITAL AUDIO
(OPTICAL) REMOTE CONTROL RS-232C INPUT
(CONTROL/SERVICE) OUTPUT DVI INPUT 1/2 PC AUDIO INPUT RGB INPUT
(PC/DTV INPUT) COMPONENT1 INPUT AC IN G-LINK OUTPUT DIGITAL AUDIO
(OPTICAL) O E D V S
I REMOTE CONTROL RS-232C INPUT
(CONTROL/SERVICE) DVI INPUT PC AUDIO INPUT RGB INPUT
(PC/DTV INPUT) COMPONENT1 INPUT O E D V I
) O N O M
L I O D U A R 1 O E D V I 1/2 1 2 3 Connect one end of an optical cable to the TV Digital Audio Optical Output port. Connect the other end of the optical cable to the digital audio optical input on the audio equipment. See the external audio equipment instruction manual for operation. When connecting with external audio equipments, such as amplifers or speakers, please turn the TV speakers off.(Refer to p.80) CAUTION Do not look into the optical output port. Looking at the laser beam may damage your vision. Monitor Out Setup (32LX1D/2D, 32/37/42LP1D only)
- The TV has a special signal output capability which allows you to hook up a second TV or monitor. Installation R AUDIO (MONO) L VIDEO S-VIDEO MONITOR OUT VIDEO1 COMPONENT1 R L AUDIO INPUT VIDEO INPUT 1/2 S-VIDEO IN
(R) AUDIO (L) VIDEO Second TV 1 2 2 Connect the second TV or monitor to the TVs MONITOR OUTPUT jacks. See the Operating Manual of the second TV or monitor for further details regarding that devices input settings. Component1/2 input sources can be used for Monitor out. When connecting with external audio equipments, such as amplifers or speakers, please turn the TV speakers off.(Refer to p.80) CableCARDTM Setup 32, 37, 42 inch TV Back 26 inch TV Back HDMI CableCARD IEEE 1394 CABLE ANTENNA CableCARD HDMI IEEE 1394 COMPONENT1 T U P N I O E D V I L R T U P N I I O D U A
- To view the premium stations Insert the CableCARDTM received from Cable Service provider to CableCARD slot of TV as shown. If the pairing information about this TV and the CableCARD is automatically displayed on the screen, contact with Cable service provider by phone. Caution:
When removing the CableCARDTM, do not drop it as this may cause damage to the card. Different card types can be used with this unit
(Motorola, Scientific Atlanta, SCM, etc.). Installation PC Setup
- This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. The TV sends configuration information (EDID) to the PC using the Video Electronics Standard Association
(VESA) Display Data Channel (DDC) protocol. When connecting with a D-sub 15 pin cable 32, 37, 42 inch TV Back 26 inch TV Back AC IN G-LINK DIGITAL AUDIO
(OPTICAL) REMOTE CONTROL RS-232C INPUT
(CONTROL/SERVICE) OUTPUT DVI INPUT PC AUDIO INPUT RGB INPUT
(PC/DTV INPUT) COMPONENT1 INPUT AC IN G-LINK OUTPUT DIGITAL AUDIO
(OPTICAL) O E D V S
I REMOTE CONTROL RS-232C INPUT
(CONTROL/SERVICE) DVI INPUT PC AUDIO INPUT RGB INPUT
(PC/DTV INPUT) COMPONENT1 INPUT 1 O E D V I O E D V I
) O N O M
L I O D U A R 2 1 1 2 AUDIO RGB-PC OUPUT PC AUDIO RGB-PC OUPUT PC 1 2 3 4 Connect the RGB output of the PC to the RGB INPUT (PC/DTV INPUT) jack on the set. Connect the PC audio output to the PC AUDIO INPUT jack on the set. Turn on the PC and the set. Select RGB-PC input source with using the TV/VIDEO button on the remote control. Installation HDMI IEEE 1394 COMPONENT1 When connecting with a HDMI to DVI cable 32, 37, 42 inch TV Back 26 inch TV Back G-LINK DIGITAL AUDIO
(OPTICAL) R AUDIO (MONO) L VIDEO S-VIDEO REMOTE CONTROL RS-232C INPUT
(CONTROL/SERVICE) OUTPUT DVI INPUT COMPONENT1 HDMI DVI (VIDEO) IEEE 1394 MONITOR OUT VIDEO1 CABLE G-LINK OUTPUT REMOTE CONTROL RS-232C INPUT
(CONTROL/SERVICE) DVI INPUT DIGITAL AUDIO
(OPTICAL) O E D V S
I PC AUDIO INPUT RGB INPUT
(PC/DTV INPUT) COMPONENT1 INPUT R L AUDIO INPUT VIDEO INPUT ANTENNA PC AUDIO INPUT RGB INPUT
(PC/DTV INPUT) COMPONENT1 INPUT O E D V I
) O N O M
L I O D U A R 2-2 1 O E D V I T U P N I O E D V I 1 L R T U P N I I O D U A 2-1 2-2 AUDIO DIGITAL AUDIO OPTICAL DVI-PC OUTPUT 1 PC Select or , depending on your PC connector. 2-2 2-1 2-1
(R) AUDIO (L) DIGITAL AUDIO OPTICAL DVI OUTPUT PC 1 Connect the DVI output of the PC to the HDMI jack on the set. 2-1 Connect the PC audio output to the PC AUDIO INPUT jack on the set. 2-2 Connect the PC optical audio output to the DIGITAL AUDIO DVI INPUT jack on the set. 3 4 Turn on the PC and the set. Select HDMI/DVI input source with using the TV/VIDEO button on the remote control. If the PC has a DVI output and no HDMI output, a separated audio connection is necessary. If the PC supports Auto DVI function, the output resolution of the PC will be automatically set to 1280x720p. If the PC does not support Auto DVI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of PC graphics card's output resolution to 1024x768, 60Hz. Installation 1. To get the best picture quality, adjust the PC 7. 2. 3. graphics card to 1024x768, 60Hz. If the graphic card on the PC does not output ana-
log and digital RGB simultaneously, connect only one of either PC INPUT or DVI INPUT to display the PC on the TV. If the graphic card on the PC does output analog and digital RGB simultaneously, set the TV to either RGB or DVI; (the other mode is set to Plug and Play automatically by the TV.) If using a sound card, adjust the PC sound as required. 4. Depending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use. 5. When Source Devices connected with HDMI1/DVI Input, output PC Resolution (VGA, SVGA, XGA), Position and Size may not fit to Screen.Press the ADJUST button to adjust the screen Position of TV SET and contact an PC graphics card service cen-
ter. 6. When Source Devices connected with HDMI1/DVI Input, output TV SET Resolution (480p, 720p, 1080i) and TV SET Display fit EIA/CEA-861-B Specification to Screen. If not, refer to the Manual of HDMI1/DVI Source Devices or contact your ser-
vice center. In case HDMI/DVI Source Devices is not connect-
ed Cable or poor cable connection, "NO SIGNAL"
OSD display in HDMI1/DVI Input. In case that Video Resolution is not supported TV SET output in HDMI1/DVI Source Devices, "INVALID FOR-
MAT" OSDdisplay. Refer to the Manual of HDMI1/DVI Source Devices or contact your ser-
vice center. 8. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC, HDMI/DVI mode. If noise is present, change the PC or HDMI/DVI mode to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card. 9. Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become permanently imprinted on the screen. 10.The synchronization input form for Horizontal and Vertical frequencies is separate. Supported Display Resolution
(RGB-PC, HDMI/DVI Mode) Supported Display Resolution
(RGB-DTV, HDMI/DVI Mode) Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) 1280x720p 1920x1080i 720x480p 45 67.5 31.5 60 60 60 640x350 720x400 640x480 800x600 1024x768 31.468 37.861 31.469 37.927 31.469 37.861 37.500 35.156 37.879 48.077 46.875 48.363 56.476 60.023 70.09 85.08 70.08 85.03 59.94 72.80 75.00 56.25 60.31 72.18 75.00 60.00 70.06 75.02 Reference External Control Device Setup External Control Device Setup
- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the Monitors functions externally.
- Connect the serial port of the control device to the RS-232C jack on the TV back panel.
- RS-232C connection cables are not supplied with the TV. RS-232C Setup RS-232C Setup AC IN G-LINK DIGITAL AUDIO
(OPTICAL) REMOTE CONTROL RS-232C INPUT
(CONTROL/SERVICE) OUTPUT DVI INPUT PC AUDIO INPUT RGB INPUT
(PC/DTV INPUT) COMPONENT1 INPUT PC TType of Connector; D-Sub 9-Pin Male ype of Connector; D-Sub 9-Pin Male No. Pin Name 1 2 3 4 5 6 7 8 9 No connection RXD (Receive data) TXD (Transmit data) DTR (DTE side ready) GND DSR (DCE side ready) RTS (Ready to send) CTS (Clear to send) No Connection RS-232C Configurations RS-232C Configurations 1 5 9 6 7-Wire Configurations
(Serial female-female NULL modem cable) 3-Wire Configurations
(Not standard) PC 2 3 5 4 6 7 8 RXD TXD GND DTR DSR RTS CTS TV 3 2 5 6 4 8 7 TXD RXD GND DSR DTR CTS RTS PC 2 3 5 4 6 7 8 RXD TXD GND DTR DSR RTS CTS TV 3 2 5 4 6 7 8 TXD RXD GND DTR DSR RTS CTS D-Sub 9 D-Sub 9 D-Sub 9 D-Sub 9 Reference Maintenance Maintenance
- Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning. Cleaning the Screen Cleaning the Screen 1. Heres a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until its almost dry, and then use it to wipe the screen. 2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV. Cleaning the Cabinet Cleaning the Cabinet To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please be sure not to use a wet cloth. Extended Absence Absence Extended If you expect to leave your TV dormant for a long time (such as a vacation), its a good idea to unplug the power cord to protect against possible damage from lightning or power surges. Product Specifications Product Specifications MODEL Width (inches / mm) Height (inches / mm) Depth (inches / mm) Weight (pounds / kg) Power requirement Television System Program Coverage External Antenna Impedance MODEL Width (inches / mm) Height (inches / mm) Depth (inches / mm) Weight (pounds / kg) Power requirement Television System Program Coverage 26LX1D 31 / 787.7 20 / 510 7.6 / 193.4 41.2 / 18.7 26LX2D 31 / 787.7 19.2 / 487 10 / 253 40 / 18.1 32LX1D 36.3 / 922 23.6 / 599.7 8.6 / 218.5 54 / 24.5 32LX2D 36.3 / 922 24.1 / 613.4 11.3 / 287.5 56.2 / 25.2 AC 100-240V~ 50/60Hz 1.5A AC 100-240V~ 50/60Hz 2.0A VHF 2 ~ 13, UHF 14 ~ 69, CATV 1 ~ 135, CADTV 1 ~ 135, DTV 2 ~ 69 NTSC-M, ATSC 32LP1D 40 / 1016 24.7 / 627.5 8.03 / 204 70.5 / 32 75 37LP1D 45.6 / 1158 28.3 / 719 8.4 / 213.1 91.5 / 41.5 42LP1D 50.8 / 1290 31.7 / 804 9.7 / 247.5 101.4 / 46 AC 100-240V~ 50/60Hz 2.0A AC 100-240V~ 50/60Hz 2.4A AC 100-240V~ 50/60Hz 3.5A VHF 2 ~ 13, UHF 14 ~ 69, CATV 1 ~ 135, CADTV 1 ~ 135, DTV 2 ~ 69 NTSC-M, ATSC External Antenna Impedance 75 The specifications shown above may be changed without prior notice for quality improvement.