User Manual PRODUCT NAME : Bluetooth 4.0 Module MODEL NAME : WB2NB8(TWBM-C302D) The information contained herein is the exclusive property of LG Innotek and shall not be distributed, reproduced or disclosed in whole or no in part without prior written permission of LG Innotek. REG. DATE : 2017. 10. 18 SPECIFICATION REV. DATE : 2017. 10. 18 MODEL NAME : WB2NB8(TWBM-C302D) REV. NO : 1.0 PAGE :
1 / 9 DOCUMENT No. : -
Table of Contents No Description 1 2 3 4 5 6 7 8 9 Features Picture of Product Installation Manual Block Diagram Absolute Maximum Ratings Operating Test Conditions Standard Test Conditions Pin Description Outline Drawing 10 Packing Information Page 2 2 3 4 4 5 5 6 7 8 Copyright. 2017. All Rights Reserved. REG. DATE : 2017. 10. 18 SPECIFICATION REV. DATE : 2017. 10. 18 MODEL NAME : WB2NB8(TWBM-C302D) REV. NO : 1.0 PAGE :
2 / 9 DOCUMENT No. : -
1. Features TWBM-C302D is the small size and low power module for Bluetooth 4.0. TWBM-C302D is based on Qualcomm CSR8510A10.
Bluetooth 4.0 specification with EDR function / Class 1
Size : 34mm x 19mm x 3.1 mm
Internal PCB Printed Antenna
USB 2.0 interface
Application : DTV, DVR, HD DVD Player, Blue-ray Disk Player, STB 2. Picture of Product
< Top >
< Bottom >
Copyright. 2017. All Rights Reserved. REG. DATE : 2017. 10. 18 SPECIFICATION REV. DATE : 2017. 10. 18 MODEL NAME : WB2NB8(TWBM-C302D) REV. NO : 1.0 PAGE :
3 / 9 DOCUMENT No. : -
3. Installation Manual Install the module like below on the Sound bar Copyright. 2017. All Rights Reserved. REG. DATE : 2017. 10. 18 SPECIFICATION REV. DATE : 2017. 10. 18 MODEL NAME : WB2NB8(TWBM-C302D) REV. NO : 1.0 PAGE :
4 / 9 DOCUMENT No. : -
4. Block Diagram Ant.
(2402~2480 MHz) RF LPF 2.4GHz Radio CSR8510 A10 RAM ROM MMU MCU I/O 3.3V USB PIO 26MHz EEPROM r o t c e n n o C e c a f r e t n I 5. Absolute Maximum Ratings Caution : The specifications below the Table define levels at which permanent damage to the device can occur. Function operation is not guaranteed under these conditions. Operating at absolute maximum conditions for extend periods can adversely affect the long-term reliability of the device. Parameter Storage Temperature Storage Humidity (40) Min
-10
-
Max
+80 90 Unit
%
Other conditions 1) Do not use or store modules in the corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are contained. Also, avoid exposure to moisture. 2) Store the modules where the temperature and relative humidity do not exceed 5 to 40 and 20 to 60%. Copyright. 2017. All Rights Reserved. REG. DATE : 2017. 10. 18 SPECIFICATION REV. DATE : 2017. 10. 18 MODEL NAME : WB2NB8(TWBM-C302D) REV. NO : 1.0 PAGE :
5 / 9 DOCUMENT No. : -
6. Operating Test Conditions Parameter Min Typ Max Ambient Temperature Operating Humidity (40) 0
-
-
-
60 85 Supply Voltage 3.135 3.3 3.465 Unit
%
Vdc 7. Standard Test Conditions The Test for electrical specification shall be performed under the following condition Otherwise this following conditions, not guaranteed this performance. 7-1. Ambient condition Temperature Humidity 7-2. Power supply voltages Input power(VDD)
+3.3V 25 5 65 5%
Supply Voltage
+3.3V 0.165V(5%) Copyright. 2017. All Rights Reserved. REG. DATE : 2017. 10. 18 SPECIFICATION REV. DATE : 2017. 10. 18 MODEL NAME : WB2NB8(TWBM-C302D) REV. NO : 1.0 PAGE :
6 / 9 DOCUMENT No. : -
8. Pin Description PIN No. Pin Name 3.3VA 3.3VA NC GND GND USB+
USB-
GND GND RESET BT_WAKEUP 1 2 3 4 5 6 7 8 9 10 11 12 Type Input Input
-
-
-
Pin Description 3.3V Power Supply 3.3V Power Supply
-
Ground Ground Input / Output USB Communication signal USB D+
Input / Output USB Communication signal USB D+
-
-
Input Output Ground Ground Bluetooth Reset Bluetooth Host Wake MCU_STBY Input / Output MCU Standby A Note. 1) Recommend a Module install sequence for prevent operation failure
- Supply 3.3V power
- Connect to pins 2) Connector : 12 Pin SMD Connector A Copyright. 2017. All Rights Reserved. REG. DATE : 2017. 10. 18 SPECIFICATION REV. DATE : 2017. 10. 18 MODEL NAME : WB2NB8(TWBM-C302D) REV. NO : 1.0 PAGE :
7 / 9 DOCUMENT No. : -
9. Outline Drawing Copyright. 2017. All Rights Reserved. REG. DATE : 2017. 10. 18 SPECIFICATION REV. DATE : 2017. 10. 18 MODEL NAME : WB2NB8(TWBM-C302D) REV. NO : 1.0 PAGE :
8 / 9 DOCUMENT No. : -
10. Packing Information Copyright. 2017. All Rights Reserved. REG. DATE : 2017. 10. 18 SPECIFICATION REV. DATE : 2017. 10. 18 MODEL NAME : WB2NB8(TWBM-C302D) REV. NO : 1.0 PAGE :
9 / 9 DOCUMENT No. : -
Copyright. 2017. All Rights Reserved. FCC WARNING STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation Any changes or modifications (including the antennas) to this device that are not expressly approved by the manufacturer may void the user's authority to operate the equipment. Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications, However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. Modifications not expressly approved by the manufacturer could void your authority to operate the equipment under FCC rules. FCC RF Radiation Exposure Statement This equipment complies with FCC RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. Information for OEM integrator The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user manual of the end product. The user manual which is provided by OEM integrators for end users must include the following information in a prominent location. To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Label for end product must include Contains FCC ID: BEJ-WB2NB8, IC:
2703H-WB2NB8" or "A RF transmitter inside, FCC ID: BEJ-WB2NB8, IC: 2703H-
WB2NB8". IC WARNING STATEMENT This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions : (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This equipment complies with IC RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. Cet quipement est conforme aux limites tablies par Industrie Canada en matire d'exposition aux radiofrquences dans un environnement non contrl. Cet appareil et son antenne ne doivent pas tre colocaliss ou fonctionner en conjonction avec tout autre antenne ou metteur. Cet quipement doit tre install et utilis avec une distance minimale de 20cm entre le radiateur et votre corps.