all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Manual | Users Manual | 1.60 MiB | March 10 2007 | |||
1 | Cover Letter(s) | March 10 2007 | ||||||
1 | External Photos | March 10 2007 | ||||||
1 | ID Label/Location Info | March 10 2007 | ||||||
1 | Internal Photos | March 10 2007 | ||||||
1 | RF Exposure Info | March 10 2007 | ||||||
1 | Cover Letter(s) | March 10 2007 | ||||||
1 | Test Setup Photos | March 10 2007 | ||||||
1 | Cover Letter(s) | March 10 2007 | ||||||
1 | Test Report | March 10 2007 |
1 | Manual | Users Manual | 1.60 MiB | March 10 2007 |
LSP-W1000_EVNT_ENG Home Monitoring System Owners Manual MODEL: LSP-W1000
- LSP-W1000NS
- LSP-W1000PS
- LSP-W1000AC Before connecting, operating or adjusting this product, please read this owners manual carefully and completely. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulat-
ed dangerous voltage within the products enclosure that may be of sufficient magni-
tude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and main-
tenance (servicing) instructions in the litera-
ture accompanying the product. FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifica-
tions to this equipment may cause harmful interfer-
ence unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. REGULATORY INFORMATION: FCC Part 15 This equipment has been tested and found to com-
ply with the limits for a Class B digital device, pursu-
ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the product is operated in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guar-
antee that interference will not occur in a particular installation. If this product does cause harmful inter-
ference to radio or television reception, which can be determined by turning the product off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the product and receiver. Connect the product into an outlet on a circuit different from that to which the receiver is con-
nected. Consult the dealer or an experienced radio/TV technician for help.
- Labelling information:
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
- RF Exposure Statement:
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be colocated or operating in conjunction with any antenna or transmitter other than those contained in this device. FCC Regulations Part 15 Declaration of Conformity (DoC) LG Corporation declares that the equipment described in this document is within the require-
ments of the Code of Federal Regulations listed below:
Title 47 Part 15, Subpart B, Class B for a digital device. This declaration is based upon the compliance of the data transceiver to the above standards. LG has determined that the models listed have been shown to comply with the applicable technical standards if no unauthorized change is made in the equipment and if the equipment is properly maintained and operated. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. Disposal of your old appliance 1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/
EC. 2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facili-
ties appointed by the government or the local authorities. 3. The correct disposal of your old appliance will help prevent potential negative consequenc-
es for the environment and human health. 4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product. 2 Canada Notice This Class B digital apparatus complies with Canadian ICES-003, Issue 2, and RSS-210, Issue 4 (Dec. 2000). To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. Cet appareil numrique de la classe B est conforme la norme NMB-003, No. 2, et CNR-210, No. 4 (Dec. 2000). Pour empcher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit tre utilis l'intrieur et devrait tre plac loin des fentres a n de fournir un cran de blindage maximal. Si le matriel (ou son antenne d'mission) est install l'extrieur, il doit faire l'objet d'une licence. Operation is subject to the following two conditions:
this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The term IC: before the certi cation/registration number only signi es that the Industry Canada technical speci cations were met. This device has been designed to operate with an antenna having a maximum gain of 2 dB. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power
(EIRP) is not more than that required for successful communication. European Union
(1999/5/EC) Translated Statements of Compliance
[English]
This product follows the provisions of the European Directive 1999/5/EC.
[Danish]
Dette produkt er i overensstemmelse med det europiske direktiv 1999/5/EC
[Dutch]
Dit product is in navolging van de bepalingen van Europees Directief 1999/5/EC.
[Finnish]
Tm tuote noudattaa EU-direktiivin 1999/5/EC mryksi.
[French]
Ce produit est conforme aux exigences de la Directive Europenne 1999/5/EC
[German]
Dieses Produkt entspricht den Bestimmungen der Europischen Richtlinie 1999/5/EC
[Greek]
1999/5/C.
[Icelandic]
essi vara stenst regluger Evrpska Efnahags Bandalagsins nmer 1999/5/EC
[Italian]
Questo prodotto conforme alla Direttiva Europea 1999/5/EC.
[Norwegian]
Dette produktet er i henhold til bestemmelsene i det europeiske direktivet 1999/5/EC.
[Portuguese]
Este produto cumpre com as normas da Diretiva Europia 1999/5/EC.
[Spanish]
Este producto cumple con las normas del Directivo Europeo 1999/5/EC.
[Swedish]
Denna produkt har tillverkats i enlighet med EG-
direktiv 1999/5/EC. 3 France Notice For Metropolitan departments 2.400 -2.4835 GHz for indoor use. Some areas of France have a restricted frequency band. There are few possibilities for outdoor use:
On private property or on the private property of public persons, use is subject to a preliminary authorization procedure by the Ministry of Defense, with maximum authorized power of 100 mW in the 2446.52483.5 MHz band. Use outdoors on public property is not permitted. In the departments listed below, for the entire 2.4 GHz band:
Maximum authorized power indoors is 100 mW Maximum authorized power outdoors is 10 mW There is partial restriction of the 2.4 GHz band for outdoor/indoor in part of the 2.4 GHz band, Departments in which the use of the 24002483.5 MHz band is permitted with an EIRP of less than 100 mW indoors and less than 10 mW outdoors:
EMC Notice Products bearing the CE marking comply with the R&TTE Directive (1999/5/EC), EMC Directive
(2004/108/EC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms (in parentheses are the equivalent international standards and regulations):
EN 55022 (CISPR 22)Electromagnetic Interference EN55024 (IEC61000-4-2, 3, 4, 5, 6, 8, 11) Electromagnetic Immunity EN61000-3-2 (IEC61000-3-2)Power Line Harmonics EN61000-3-3 (IEC61000-3-3)Power Line Flicker EN 300 328-2Technical requirements for radio equipment EN 301 489-1, -17General EMC requirements for radio equipment Italia Notice Outdoor use is prohibited. 4 IMPORTANT SAFETY INSTRUCTIONS CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNERS MANUAL. AND THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE. This product has been designed and manufactured to assure personal safety. Improper use can result in elec-
tric shock or fire hazard. The safeguards incorporated in this product will protect you if you observe the follow-
ing procedures for installation, use, and servicing. This product does not contain any parts that can be repaired by the user. DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus com-
bination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service person-
nel. Servicing is required when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 1. Read these instructions. - All these safety and operating instructions should be read before the product is operated. 2. Keep these instructions. - The safety, operating and use instructions should be retained for future reference. 3. Heed all warnings. - All warnings on the product and in the operating instructions should be adhered to. 4. Follow all instructions. - All operating and use instructions should be followed. 5. Do not use this apparatus near water. - For example: near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement; or near a swimming pool; and other areas located near water. 6. Clean only with dry cloth. - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instruc-
tions. - Slots and openings in the cabinet are pro-
vided for ventilation and to ensure reliable operation of the product and to protect it from over-heating. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar sur-
face. This product should not be placed in a built-
in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturers instructions have been adhered to. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other appa-
ratus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polar-
ized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the pro-
vided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 5 I L A N O T D D A I M A R G O R P WAN Port ......................................................20 DDNS (Dynamic Domain Name System) .....20 Sender Mail ...................................................21 Receiver Mail ................................................21 Notification ...................................................21 Wireless .......................................................22 System Settings ................................................22 Clock .............................................................22 User Password ..............................................22 Recording .......................................... 24 Instant recording ..............................................24 PC requirements ...............................................26 Recommended PC requirements ..................26 Using the Web Viewer ......................................28 AP (Access Point) settings ..............................28 Status ............................................................28 WAN Port Configuration ................................29 Access Control ..............................................29 Denial of Service Setting ..............................30 Port Forwarding ............................................30 Special Application ........................................30 Config File .....................................................31 System Log ...................................................31 IP Filtering .....................................................32 MAC Filtering ................................................32 URL Filtering .................................................32 Upgrade Firmware ........................................33 Reference ......................................... 34 Troubleshooting ...............................................34 Recommended devices ....................................37 Supported external USB device list ..............37 The necessary Capacity for 1Hour recording (Approximatly) .........................37 Factory default configuration settings ...........38 Specifications ...................................................40 Contents Introduction ......................................... 7 Features ...............................................................7 Notice Regarding Wireless Communications ..7 Netstation (Main unit) .........................................8 Front panel ......................................................8 Rear panel ......................................................8 Camera .................................................................9 Front panel ......................................................9 Accessories .........................................................9 Side panel .......................................................9 Rear panel ......................................................9 Remote Control .................................................10 Remote Control Operation ............................10 Connecting cameras ........................................11 Wired connection ..........................................11 Connect the camera with wirelessly .............11 Connecting the Display device .......................11 Video connection ..........................................11 Hookup and Settings ....................... 11 VGA connection ............................................12 Connecting the audio device ...........................12 Connecting the USB device .............................12 Connecting to the network ..............................13 Connecting the power source .........................13 System operation ..............................................14 General explanation of the Live Screen .........15 Viewing System Information ..........................16 Viewing the System Log List ..........................16 Lock function ....................................................16 Menu configuration ..........................................17 General settings ................................................17 Camera settings ................................................17 Information ....................................................17 Record settings .................................................18 Target Media .................................................18 Rec. setting ...................................................19 Display settings ................................................19 Language ......................................................19 Dwell Time ....................................................19 Network settings ...............................................20 6 Introduction Features Simply connect the LSP-W1000 to your network cameras (sold separately) and to your TV or monitor, and you'll be able to view camera images conveniently on your TV or monitor. The LG Wireless cameras can be connected as well, that is you won't have to worry about running cables from the LSP-W1000 to each camera. Use the Pan/Tilt function, aim the camera wherever you want by simply pressing the navigator keys on the included remote control. The camera's built-in sensor detects motion by people or animals moving within the sensor's range. When the sensor detects motion, the LSP-W1000 can alert you by sounding its built-in buzzer. Simply insert an optional USB memory stick or USB type external HDD device and you'll be able to record movies of your camera images. Later you can use the remote control to play back movies on your TV or monitor that were recorded by the LSP-W1000. Simply press the camera's PRIVACY button to hide the camera's lens when you don't want camera images to be seen. Up to 4 cameras can be connected, allowing you to keep an eye on every room with just 1 LSP-W1000. When multiple cameras are registered, you can view up to 4 camera images at once and switch to monitor a specific camera if necessary. Notice Regarding Wireless Communications 1. To avoid wireless communication interference and instability, do not use this product near the following devices. Wireless transmitters (radio transmitters, cellular transmitters, etc.) Wireless devices which operate at 2.4 GHz (security equipment, POS systems, cordless telephones, etc.) Microwave ovens. 2. Wireless communication range and quality may be affected if the following types of objects are located between or near this product and other wireless devices connected to this product. In the event that images do not refresh at a regular rate, become cut off, etc., relocate this product, the other wireless devices, or the obstacles (if possible) for more stable wireless communications. Metal door shutters Walls made of concrete, stone, or brick, or walls which contain aluminiumbased heat insulation Multiple walls Fire doors and glass Steel racks or shelves 3. Place cameras and this product at least 2 m (6.5 ft.) away from radios. Do not connect cameras and this product to a power outlet used by a radio. 4. In case of low picture quality when you use the wireless mode. Change the channel of wireless option in the setup menu. Set the wireless band option to 11G. If you use a Notebook computer via the NetStation, it may cause the bad effect to the camera perfor-
mance. n o i t c u d o r t n I d n a p u k o o H s g n i t t e S i g n d r o c e R d n a h c r a e S k c a b y a P l t n e i l C m a r g o r P e c n e r e f e R 7 Netstation (Main unit) Front panel a b c d e f g h i Rear panel j k l m n o p q r s t a POWER indicator Lights when the unit is turned on. b RECORD indicator l VIDEO OUT Connect to a monitor or display device. m VIDEO/VGA select switch Lights when recording is in progress. Video or VGA output mode select switch. c ALERT indicator Lights when the camera is disconnected or the system log will not be able to be saved. n VGA OUT Connect a VGA monitor. o USB port d MOTION DETECT indicator Blinks when a motion is detected. e WAN indicator Blinks when a network is connected. f LAN (1-4) indicators Fast blinking when the unit is connected to cameras with LAN cable. g WIRELESS indicator Fast blinking when the wireless camera is in progress. h USB port Connect an USB memory stick or USB type external HDD device for recording or playback. i Remote Sensor Point the remote control here. j DC 12 V power input jack (Class 2 Only). k AUDIO OUT Connect the audio input signal of an external device. Connect an USB memory stick or USB type external HDD device for recording or playback. p NORMAL/SETUP select switch Mode select switch. Set the NORMAL mode to activate this unit. The SETUP mode is used only for service. q LAN (1-4) ports Connect the cameras with straight cable. r WAN port Connect the ethernet 10/100Mbps network cable for controlling this unit via a PC network. s RESET button Pushing the button resets the unit using a point-
ed object. If you need to factory reset, pushing the button for more 3 seconds and then the unit will be rebooted automatically. t Wireless Antenna 8 Camera Front panel Side panel Rear panel a b c d e f g a MIC The microphone is incorporated into the cam-
era. e Reset button Resets camera. f LAN port b STATUS indicator Displays the camera status. c PRIVACY button Set the privacy mode, it allows you to make sure images from the camera cannot be seen. d Connection mode select switch Wired or Wireless mode select switch. Connects with LAN port of main unit by using the Straight Cable. g DC 12V power input jack (Class 2 Only) Accessories AC adaptor AC cord NetStation Stand NetStation Wiress Antenna Audio/Video cable Remote Control AAA Type Battery Lan Cable Note: The accessories may be different depending on models. n o i t c u d o r t n I d n a p u k o o H s g n i t t e S i g n d r o c e R d n a h c r a e S k c a b y a P l t n e i l C m a r g o r P e c n e r e f e R 9 Remote Control OSD Accesses or removes the On-
screen Display. LOCK Displays the lock menu to change user type or disable system operation. SEQUENCE View all channels in sequence on the full screen mode. SPLIT Displays the screen mode to full or 4 screens. BUZZ.OFF Cancels alarm activation and returns the system to the condition before the alarm was activated. PAN/TILT Switches the unit to PAN/TILT mode to control the connected camera. SETUP Displays the setup menu or can-
cels operation of the setup menu. Arrow Buttons (b B v V) Selects or moves between the menu options. ENTER Confirms menu selections. SEARCH Displays the search menu. RETURN Returns to the previous menu or level. MARK Makes the mark point. Use this button to move the registed cam-
era position. PAUSE (X) Pauses playback. STOP(x) Stops playback or recording. REC (z) Starts recording. m/c/. Searches the recorded images in reverse or skips the recorded images. bB Playback or reverse playback of recorded images. M/C/>
Forward searches the recorded images or skips the recorded images. Number Buttons (0,1-9) Selects a channel directly or use for network settings. INFO Displays the system information window. LOG Displays the System Log List win-
dow. ZOOM + / -
Zooms in/out on live images. STORAGE Displays the Taget Media Space Information window.
*: This buttons are not available for this unit. Remote Control Operation Point the remote control at the remote sensor and press the buttons. Cautions:
Do not mix old and new batteries and never mix different types of batteries such as standard, alkaline, etc. Do not put the batteries in the place where young children can reach. Remote Control Battery installation Detach the battery cover on the rear of the remote control, and insert two batteries (size AAA) with 3 and #
aligned correctly. 10 Hookup and Settings Precautions Be sure to switch off the camera before installation and connection. Connecting cameras Up to 4 cameras can be connected to the Netstation. You will need to configure the camera registration settings for cameras connected to the Netstation.
(See page ??). Wired connection Set the Camera Mode Select switch to Wired posi-
tion. Connect the LAN cabel as shown below. Turn the Netstation and the camera power on. The camera will be panning and tilting operation. Connect the camera with wirelessly If you want to connect without wires, following the next stpes. 1. Set the camera mode select switch to Wireless position. 2. Pushing the reset button to reset the camera using a pointed object. The camera will be panning and tilting operation. Note:
The wireless function is possible after configuring the camera registration settings for cameras connected to this unit. (See page 17). Connecting the Display device Rear of camera Make one of the following connections, depending on the capabilities of your existing equipment. Video connection When using the VIDEO OUT jacks, set the Video Output mode select switch to VIDEO. Connect the VIDEO OUT jacks on the rear of the Netstation to the corresponding input jacks on the TV or monitor using an VIDEO cable. Notes:
If the camera is not connected to the Netstation with LAN cable, the panning and tilting operation is not be activated even if the camera is powered on condition. Before connection, set the camera Connection Mode Select switch to Wired position. If you connect or registrer the camera to the Netstation using the LAN cable, you should use the supplied LAN cable or STP cable for shield the electromagnetic interference. The camera(s) is(are) will be used after configur-
ing the camera registration settings. (See page 17). Note:
If the OSD is displayed too brightly, the OSD may be shown like flickering on the monitor. In that case, adjust the brightness. n o i t c u d o r t n I d n a p u k o o H s g n i t t e S i g n d r o c e R d n a h c r a e S k c a b y a P l t n e i l C m a r g o r P e c n e r e f e R 11 VGA connection When using the VGA OUT jack, set the Video Output mode select switch to VGA. Connect the VGA OUT jacks on the rear of the NetStation to the corresponding input jacks on the TV or monitor using an VGA cable. Connecting the USB device Connect the USB memory stick or external USB HDD device for recording or playing. Then, you should use the recommened USB devices. (see page ??) Note:
If the picture position is unbalanced on the VGA mon-
itor, refer to the owner's manual of the VGA monitor to adjust the picture position of the VGA monitor. Connecting the audio device Connect the AUDIO OUT jacks on the unit to the mono audio in jacks on your audio deivce. 12 Connecting to the network Connect the WAN port with a straight ethernet cable. Connecting the power source Connect a DC 12 V power source to the DC 12 V input terminal as shown below. When camera pow-
ered up, the camera performs a self-check (including one panning and tilting operation). Router Modem Notes:
If you use the Router, you should set the Port Forwarding. If the IP address of both Netstation and external Router is same, the Netstation is not operate normally. In this case, you should change the IP address of the Router to solve the problem. Notes:
Use the supplied adaptor to prevent malfunction. The panning and tilting operation activates only when the camera is connected to the Netstation with LAN cabel. n o i t c u d o r t n I d n a p u k o o H s g n i t t e S i g n d r o c e R d n a h c r a e S k c a b y a P l t n e i l C m a r g o r P e c n e r e f e R 13 5. Wireless Setup menu is displayed. System operation After the power is inputted for the first time to turn on the unit or set the unit as factory resetting, you will set the initial Administrator password and wireless setup manually. 1. Connects the camera(s) to the main unit using the Ethernet cable. 2. Connects the main unit to the monitor or display unit and turn them all on. 6. Use V v b B to select the desired setting as shown below.
- SSID: You can change the SSID. Set the iden-
tifier for the wireless network local in use.
- Band: Select the band (2.4GHz (G) or 2.4GHz
(B+G).
- Channel: Select the channel. (Auto or 1-
11(NTSC)/1-13(PAL))
- WEP Key: You can set the WEP key to protect a wireless signal between this Netstation and connected camera(s). The WEP key is ran-
domly created. 7. Press ENTER while [Apply] option is selected. Update window is displayed and update will start. After update is completed, the Camera Registration menu is displayed. To register the camera(s), see page 17. 3. When the booting is completed the Password Setup window will be displayed. You can make the user password for this unit. 4. Input a new password more than 4-digit numbers and press ENTER. You can enter the password from minimum 4-digit numbers to 8-digit numbers. Enter it again and press ENTER to verity. If you make a mistake before pressing ENTER, press b. 8. After all settings are completed, press RETURN and select [Yes] then press ENTER to confirm your setting. 14 General explanation of the Live Screen a b c d e f g h i j a Live Screen Displays the current surveillance live screen. b Zoom Displays the current zoom level. c Status display icon Displays the icon of detected motions or record-
ing status. d Connect type with camera Displays the current connected mode between the Netstation and the camera.
: Displays when you connect the camera with wires.
: Displays when you connect the camera in wireless mode. e Connected USB device position Displays the connected USB device position.
: When you connect the USB to the front of unit.
: When you connect the USB to the rear of unit. f Channel Number Displays the channel number. g Camera Name Displays the edited camera name. h Selected Channel Displays the selected channel with yellow box. i Date & Time Indicates current date and time j Current status of this channel Displays when not registered the camera. n o i t c u d o r t n I d n a p u k o o H s g n i t t e S i g n d r o c e R d n a h c r a e S k c a b y a P l t n e i l C m a r g o r P e c n e r e f e R 15 Viewing System Information To view system information:
1. Press INFO. The system information window is displayed. 2. Press ENTER to exit the window. Viewing the System Log List To view the system log list:
1. Press LOG. The system information window is displayed. Notes:
The system log list. Camera Channel move, Camera Channel regis-
tration, Camera connect, camera disconnect, User
(Admin/Normal) Log In, User (Admin/Normal) Log Out, USB Add, USB Format, USB Remove, Rec. Mode change, Network change, Password change, Wireless change, Factory Reset, Write error and Power On. If you want to erase the system log, select [Clear]
and then press ENTER. Lock function You can change user type or disable system opera-
tion. 1. Press LOCK. The login window is displayed. 2. Use b / B to select a user type.
- Administrator: Unlimited operation of the unit.
- Normal User: Use of the limited functions of the system. (Split monitor and live image view are available.) 3. Press V and enter the password. You can see the live screen and operate the sys-
tem. Note:
If you select normal user for the first time, initial pass-
word is "0000". Use b / B to see the previous or next log list. 2. Use b / B to select [Close] icon and press ENTER to exit the window. 16 Menu configuration The features and options of this unit are configured through the menu. The operations of this unit can be set via a menu dis-
played on the monitor. Camera settings Information Displays registered camera(s) informations. First level Second level Third level Help menu General settings Arrow (v/V/b/B) Buttons:
Use these buttons to select the menu options or adjust the options value. ENTER:
Select the option or confirm the setting. RETURN:
Return to the previous menu or level. Close the displayed windows. 1. Press SETUP to display the setup menu. 2. Use v / V to select the desired option. 3. While the desired item is selected, press B or ENTER move to the second level. 4. Use v / V to select the desired option then press B or ENTER to move to the third level or displays selected option windows. 5. Use v / V / b / B to select the desired option then press ENTER to set the value. 6. Use v / V / b / B to select the desired setting then press ENTER to confirm your selection. 7. Press RETURN to exit the setup menu. Note:
If you change the option value and then exit the menu or return to the previous menu, the saved message will appears. Then, select [Yes] and press ENTER to save the settings. l Ch: Displays the channel number. l Camera Name: Displays the registered camera name. l Preset: Displays the selected preset name in the camera registration menu. l Type: Displays the connected type of the camera. Registration You should register the camera when using it for the first time. You can add, move and erase the camera(s). If you register the camera, the camera should be connected to the Netstation with network cable and you should set the camera mode select switch to Wired position. l CH: Selects the desired channel to register cam-
era. l Camera Name: Display the camera name. l Quality: Selects the encording bitrate of MPEG4 encoder in the connected camera. (High, Mid. or Low) n o i t c u d o r t n I d n a p u k o o H s g n i t t e S i g n d r o c e R d n a h c r a e S k c a b y a P l t n e i l C m a r g o r P e c n e r e f e R 17 Tip:
Remote control buttons for entering a name. Numbers (0-9): Enters the corresponding character at the cursor posit ion. m / M: Moves cursor to left or right. Record settings Target Media Select a media to record. The USB device should be connected to the NetStation for recording. l Res.: Selects the resolution of camera input sig-
nals. (D1: 720x480, CIF: 320x240). l Flip: Set Flip to ON, when you see the live screen to filp the picture. l Preset: Selects the picture quality of video sensor in the connected camera. (AUTO, P1(Fluorescent), P2 (Daylight), P3 (Cloudy), P4 (Incandescent) or P5 (CRT)) Moving a registered camera channel 1. Select a camera channel and press MARK. 2. Use v / V to choose a new channel to move the registered camera into the channel, then press ENTER. Change the registered camera name You can change the camera name. The names can be up to 16 characters long. 1. Choose the camera channel you want to change the name, then press ENTER. 2. Press v or V to display the character input menu. 3. Enter a new name. Use b / B / v / V to select a character then press ENTER to confirm your selection. Using the character input menu l None: No recording. l USB Front: Selects when you connect the USB device to the front panel of main unit. l USB Rear: Selects when you connect the USB device to the front panel of main unit. l Size: Displays the free space of the selected USB device. l Format: To format the selected USB media. l USB Test: To test the USB device.
- Language: Use b / B to change keyboard type.
- Space: Inserts a space at the cursor position.
- Delete: Deletes the previous character at the cur-
sor position.
- b, B: Moves cursor to left or right.
- OK: Select to finish.
- Cancel: Cancels all entered characters. 18 Rec. setting 1. Use v/V to select the camera channel and press ENTER. 2. Use v/V to select recording mode for selected camera. 3. Press ENTER to confirm your settings. Display settings Language Select a language for the setup menu and informa-
tion display. Dwell Time You can set the channel sequence time to 2 seconds, 5 seconds, 10 seconds, 30 seconds or 60 seconds. l CH: Displays the channel number. l Camera Name: Display the camera name. l Rec. Mode: Selects the desired recording option.
- No Rec.: Instant recording is possible using the REC button of the remote control.
- Motion: Recording starts automatically when motion is detected.
- Continuous: Continuous recording. l Post Time: Specify the post-event recording time that records the situation from when the motion has been detected. This option is activated when the Rec. Mode is set the Motion mode. n o i t c u d o r t n I d n a p u k o o H s g n i t t e S i g n d r o c e R d n a h c r a e S k c a b y a P l t n e i l C m a r g o r P e c n e r e f e R 19 Network settings WAN Port DDNS (Dynamic Domain Name System) l Type:
- DHCP: DHCP stands for Dynamic Host Configuration Protocol. Network settings of this unit are configured automatically by the DHCP server. If you set to DHCP, the [IP Address],
[Subnet Mask] and [Gateway] options are dimmed and these options are not set.
- Static: Enter the network settings manually. l IP Address: Enter an IP address using the number buttons (0-9) or Arrow (v/V/b/B) buttons. l Subnet Mask: Enter a subnet mask address using the number buttons (0-9) or Arrow (v/V/b/B) but-
tons. l Gateway: Enter the gateway address using the number buttons (0-9) or Arrow (v/V/b/B) buttons. l DNS DHCP:
- ON: DNS settings of this unit are configured automatically by the DHCP server. If you set to ON, the [Main DNS] and [Sub DNS], options are dimmed and these options are not set.
- OFF: Enter the DNS settings manually. l Main DNS: Enter the Main DNS server address using the number buttons (0-9) or Arrow (v/V/b/
B) buttons. l Sub DNS: Enter the Sub DNS server address using the number buttons (0-9) or Arrow (v/V/b/
B) buttons. Notes:
For more detail on WAN Port setup, ask your network administrator and/or network service pro-
vider. After change the options, select [Apply] icon and press ENTER to confirm the settings. l DDNS
- ON: Select to enable DDNS function. This free service is very useful when com-
bined with the Virtual Server feature. It allows Internet users to connect to your Virtual Servers using a URL, rather than an IP Address. This also solves the prob-
lem of having a dynamic IP address. With a dynamic IP address, your IP address may change whenever you connect, which makes it difficult to connect to you.
- OFF: If you set to OFF, the [Provider], [Domain URL], [ID] and [Password] options are dimmed and these options are not set. l Provider: Select the desired DDNS Service Provider from the list (DynDNS or TZO). From the Internet, users will now be able to connect to your Virtual Servers (or DMZ PC) using your Domain URL. l Domain URL: Apply for a Domain URL, and ensure it is allocated to you. l ID: Enter the DDNS registered user ID for the DDNS Service. l Password: Enter the user password in [ID] for the DDNS Service. Notes:
After change the options, select [Apply] icon and press ENTER to confirm the settings. The DDNS function is serviced using a TCP 8245 port by "No-IP"(http://www.no-ip.com/). In case the unit is used in the network system with a firewall, you have to open the TCP 8245 port so that DDNS data can get into firewall. For more detail on firewall setup, ask your network administrator and/or network service provider. 20 Sender Mail Note:
After change the options, select [Apply] icon and press ENTER to confirm the settings. Notification Set the notification options. 1. Select item and press ENTER. A checking mark appears in front of the selected option. 2. Select [Apply] icon and press ENTER to confirm your settings. l Motion Detection: Sends an E-mail when motion detection has occurred. l USB storage Full: Sends an E-mail when the disc has fully recorded. l Admin PW Change: Sends an E-mail when the administrator password has changed. l Camera Disconnect: Sends an E-mail when a video signal from the camera has stopped because of a cable disconnection or malfunction of a cam-
era. Note:
For the E-mail sending function, the motion detection has 1 minute term before sending an E-mail again. l Mail Send
- ON: Select to enable Mail function.
- OFF: If you set to OFF, the [SMTP Server], [Mail Address] and [Password] options are dimmed and these options are not set. l SMTP Server: Enter the SMTP Server address. l Mail Address: Enter the mail address. l Password: Enter the password. Notes:
After change the options, select [Apply] icon and press ENTER to confirm the settings. When you press ENTER, the test mail will be sent via the SMTP server to the user mail address automati-
cally and the settings are saved when the mail test of the SMTP server is correct. You should know the SMTP server address of a mail service provider to use the SMTP server.
(You should use the port number 25 of the SMTP server for this function.) Receiver Mail l Address (1~4): Enter the receiver mail address. You can input up to 4 E-mail addresses. n o i t c u d o r t n I d n a p u k o o H s g n i t t e S i g n d r o c e R d n a h c r a e S k c a b y a P l t n e i l C m a r g o r P e c n e r e f e R 21 Wireless Set the Wireless options. System Settings Clock l Clock Mode: Select the clock setting mode. Set to
[Auto] when using the NTP (Network Time Protocol) server for time adjustment. If the "Clock Mode" is set to [Manual], the time settings should be entered manually and the [NTP Server], [Time Zone] and
[Daylight Saving] options are deactivated. l Date: Enter the current date. l Time: Enter the current time. l NTP Server: Select NTP server. You may choose to select NTP server from the pull-down menu. l Time Zone: Select your Time Zone. If your time zone is wrong selected, the E-mail sending time may be displayed in a wrong way. l Daylight Saving: Set to ON to you use the daylight saving function. l Wireless
- ON: Select to enable Wireless function.
- OFF: Select to unable the Wireless function. l SSID: You can change the SSID. Set the identifier for the wireless network local in use. Do not use the SSID that is the same as the other wireless device. l Band: Select the band (2.4GHz (G) or 2.4GHz
(B+G). l Channel: Select the channel. (Auto or 1-
11(NTSC)/1-13(PAL)). Use the same channel as that of the other wire-
less device, this unit may not be activated nor-
mally. In this case, change the channel. l WEP Key: You can set the WEP key to protect a wireless signal between this Netstation and con-
nected camera(s). The WEP key is randomly cre-
ated. Notes:
After change the options, select [Apply] icon and press ENTER to confirm the settings. If you change the wireless options in the case of the camera is not connected to the Netstation, the camera(s) may not be activated normally. If you connect the NetStation and the camera with the wireless network, it may occur the interference with the other wireless device. In that case, refer to the owner's manual of the other wireless device to solve the problem. 22 User Password Buzzer l Administrator: You can change the password by entering the new password for the administrator. l Normal User: Enter the password for the normal user. Note:
Remember the new password. If you forget the new password, reset the unit and then the password and all settings are set to factory default settings .
- ON: Makes a sound when a motion is detected.
- OFF: Turns off the motion buzzer. Factory Reset You can reset the unit to its original factory settings. 1. Select [Reset] and press ENTER. Auto Log Out Logout is automatically at fixed intervals. You can set auto logout time to 5 minutes, 10 minutes, 30 minutes or 60 minutes. 2. Use b/B to select [Yes] then press ENTER. The unit will be turned off and on automatically after a few seconds. n o i t c u d o r t n I d n a p u k o o H s g n i t t e S i g n d r o c e R d n a h c r a e S k c a b y a P l t n e i l C m a r g o r P e c n e r e f e R 23 Recording Images from a camera will be recorded on the con-
nected USB memory stick or external USB HDD device. Before you start recording, first check the Target media settings in the record menu, and then make the recording target media settings. Instant recording Ensure all the cameras and USB memory sitck or external USB HDD device are connected and that time and date have been set correctly. 1. Use v/V/b/B to select a live channel you want to record. 2. Press the REC button. The RECORD indicator of the unit turns red and the recording type indicator is displayed on the selected channel screen. 3. Press the STOP button you want to stop record-
ing. If the motion or continuous recording is set, the recording mode will be changed into the motion or continuous recording mode. Note:
A USB memory stick or external USB HDD device must be connected in the main unit in order to record camera images. Motion recording Images are recorded only when the specified cam-
era's sensor is activated. 1. Press SETUP to display setup menu. 2. Use v/V/b/B to select [Rec. Setting] option. The Recording mode setting menu is displayed. 3. Press ENTER and use v/V to select the [Motion]
option then press B. 4. Use v/V to select post time and press ENTER. 5. Press RETURN and use b/B to select [Yes] then press ENTER. Motion recording is now set. Continuous recording Images are recorded continuously. 1. Follow steps 1-2 as shown "Motion Recording". 3. Press ENTER and use v/V to select the
[Continuous] option. 4. Press ENTER. 5. Press RETURN and use b/B to select [Yes] then press ENTER. Notes:
If you press REC during the motion or continuous recording, the recording mode will be changed into the instant recording mode. The recorded data file name is made automati-
cally as the [Channel name_export date and time]
type. If you set the Day Light Saving option to On and start recording, the word "S" is added on the end of the file name to avoid the repetition of the recorded file name. Do not remove the USB memory stick or external USB HDD device while the recording is in prog-
ress, it may cause a malfunction and the recorded data is not played. If the recored data time is shorter than 1 second, it will be delected automatically to prevent waste of space. You should record longer than 1 second to save the recorded data. Do not use the USB memory stick or exter-
nal USB HDD device that is used by the other NetStation or it may cause malfunction. You can record instantly the scheduled channels even though motion or continuous recording is set to the channels. The video signal of recorded data is saved by the MPEG 4 compression technology. The audio sig-
nal of recorded data is saved by the G.726 com-
pression technology. You can not record in following conditions.
- The USB memory sitck or external USB HDD device is not attached.
- A HDD of external USB HDD device is not for-
matted.
- The channel has no video input for display.
- The USB memory sitck or external USB HDD device has not free space. You can not record the Motion recording in follow-
ing conditions.
- The USB memory sitck or external USB HDD device is not attached.
- A HDD of external USB HDD device is not for-
matted.
- The channel has no video input for display.
- The Motion recording is not set. Priority of record. Instant record > Motion record or Continuous record. If you press SETUP during the recording, the record setting menu is displayed. You can not record the data for less than 1 sec-
onds. 24 Search and playback Functions available during playback Button x STOP Function Stop playback.
[[ PAUSE Pause playback. Press repeatedly to select the required scan speed. (M, MB, MM, MMB or m, mb, mm, mmb) While the playback is paused, press M to play in slow motion. The slow motion playback in reverse is not available. During playback, press m/M for longer than 1 second to go to the next/previous recorded data. Press to play reverse or normal playback. Press to see the reamin time of the playback files. m/M bB PLAY OSD Notes:
If you play the recorded data in the personal com-
puter or the other playable unit, MPEG 4 codec and G.726 codec is needed. You should play the recorded data that is record-
ed from the Netstation. If you play the other data that is recorded from the other unit, the Netstation may malfunction. If you remove the USB device during the search or playback, it stops the search or playback and returns to the live screen. Search the recorded data When the SEARCH button is pressed, the search menu is displayed. 1. Use v/V to select the desired source device then press ENTER. If the USB device is not connected, the source name is dimmed and it is not selectable.
- USB Front: Select when the USB device is connected to front of unit. Plays back or searches recorded contents of the connected USB device.
- USB Rear: Select when the USB device is connected to rear of unit. Plays back or searches recorded contents of the connected USB device. 2. Use v/V to select channel to search the recorded contents of the channel. 3. Press ENTER. The date seach menu is displayed. 4. Select the year, month or date to start search of the recorded data. 5. Use b/B to Select the [Get List] icon then press ENTER. The search result is displayed. 6. Select the recorded contents you want to play-
back.
- b/B: Move to previous page or next page.
- v/V: Use this buttons to select the recorded contents.
- 1~7 number buttons: You can directly select the contents. For example; If you press num-
ber 3 button, the select bar moves to the third cloum directly. 7. Press ENTER to start playback. The picture is displayed. Note:
Do not remove the external USB device while the search is in progress from the unit. It may cause a malfunction. n o i t c u d o r t n I d n a p u k o o H s g n i t t e S i g n d r o c e R d n a h c r a e S k c a b y a P l t n e i l C m a r g o r P e c n e r e f e R 25 Logging in to the Web Viewer when the computer and the Netstation are directly connect-
ed 1. Connect a computer to the LAN port of the Netstation using the network cable. 2. Turn on the computer and Netstation. 3. Set the network configuration of the computer as shown below. 1) Open the [Local Area Connection Properties]
windows. Client program Client Program is the network program of the Netstation. The description pictures may differ from your OS
(Operating System) type. The pictures used in this manual are based on Windows XP. PC requirements x OS (Operating System): Windows XP. x CPU: Intel Pentium IV 1GHz or above. x RAM: 256 MB or above. x Graphics Card: AGP VGA with 64 MB Video RAM or above. x Browser: Internet Explorer 6.0. x Etc.: HTML V4.0 or later, JavaScript V1.2 or later. Recommended PC requirements OS: Windows XP CPU: Intel Pentium IV RAM: 512 MB Graphics Card: AGP VGA with 128 MB Video RAM Notes:
Your Browser must support JavaScript. If you use the Windows Vista, Windows 2000 or Windows 98, some function may not operate cor-
rectly. If you can not install the client program, check the security settings on your computer. It has limita-
tion as depending the security settings. 26 2) Select the [Internet Protocol [TCP/IP]] and click [Properties]. 3) Select the [Obtain an IP address automati-
cally] to use DHCP. 4) Click [OK] or [Close] repeatedly to save the settings. 4. Start the web browser on the computer. 5. In the Address Box, enter "http://192.168.1.111". 6. Press ENTER and then the login page will be dis-
played. Notes:
The login page needs more time to display it according to a network condition. If the login page is not displayed, check the TCP/IP settings of the computer or the pop-up blocker. If you set the pop-up blocker, the login page is not displayed. You must allow the pop-
ups. If you connect the Netstation for the first time, the Security Warning window is displayed to install the VLC player. You must install the VLC player for using the Web Viewer. If you block the ActiveX, you can not install the VLC player. In that case, change the
"Download unsigned ActiveX controls" option to "Prompt" in the Security Settings menu
(Tools > Internet Options... > Security tab >
Custom Level... > ActiveX controls and plug-
ins) of the browser. Logging in to the Web Viewer when the Computer and the Netstation are connected via internet 1. Connect a computer to the Internet. 2. Connect the internet cable to the WAN port of the Netstation. Note:
Ensure that your computer and the Netstation are on the same network segment. 3. Turn on the computer and Netstation. 4. Check the IP Address of the Netstation. (See page ??) 5. Start the web browser on the computer. 6. In the Address Box, enter "http://" and the IP Address of the Netstation. Note:
If you connect the Netstation to the Router, you should set the Port Forwarding and use the IP address of the Router to enter the web viewer. Refer to the owner's manual of the Router for port forwarding settings. 7. Follow steps 6-8 as shown [Logging in to the Web Viewer when the Computer and the Netstation is directly connected]. You can install the VLC player manually, visit the "http://www.videolan.org" website and download the VLC player for windows. 7. Select the User ID and enter the Password of selected user ID. If you login the Netstation as Administrator, you can not login using the web viewer program. 8. Click the [Login]. The Web viewer is displayed. Note:
The Web viewer is used only for one user. n o i t c u d o r t n I d n a p u k o o H s g n i t t e S i g n d r o c e R d n a h c r a e S k c a b y a P l t n e i l C m a r g o r P e c n e r e f e R 27 Using the Web Viewer You can control the live image using the Web Viewer. a b c d e AP (Access Point) settings An access point is a bridging device for connecting a wired and wireless network together. Access points are typically wireless routers or stand-alone devices that plug into an Ethernet hub, switch, or router. Wireless adapters should be set to Infrastructure Mode when connecting to an access point or wireless router. (Infrastructure: An 802.11 network in which wireless devices communicate with each other by first going through an Access Point (AP) or wireless router. If you want to change the AP options, refer to the fol-
lowing settings. Click [AP] button and then display the Wireless Router setup window. Warning If you change the AP settings without technical knowl-
edge, the Netstation may not be activated. f g h i j i Status a Camera Status Table Shows the camera status. b Camera channel buttons Press the ch1 to ch4 channel button to see the current surveillance images. c Live screen Displays the current surveillance live screen d AP setup button Click to go to the AP Setup menu. This button is displayed only when a computer and the Netstation are directly connected using the network cabel. e Log out button Click to go to the log-in page of the Web viewer. f Display the current date and time g Display the current log-in User ID. h The 4-direction arrow buttons You can pan and tilt the camera using the 4-direc-
tion arrow buttons. i Zooming buttons You can operate the zoom range. j Displays the current zoom level. Note:
The d, h-j function is used for Administrator. 28 Internet: Shows the internet connection sta-
Connection Details:
tus. Click to show more details of the internet connection. LAN: Shows the Local area network infor-
mation. System: Briefly shows the device name and firmware information. Click to show the detailed informa-
tion of the system. Click to refresh all the data. System Data:
Refresh Screen:
WAN Port Configuration Check to enable the listed functions. Respond to WAN Ping Enable UPNP Enable IPsec pass through on VPN connection Enable PPTP pass through on VPN connection Enable L2TP pass through on VPN conenction WAN Access Type: Select the WAN access type
(PPPoE, PPTP and L2TP) from the pull-down menu. Note:
You can set the Static IP or DHCP setting in the Setup menu of the Netstation. Save: After completing the settings on this page, click Save to save the settings. Reset: Click Reset to restore to default values. Access Control User Name:
Password:
Service Name:
DNS 1-3:
Clone MAC Address:
Enter the DNS server IP address(es) provided by your ISP, or you can specify your own preferred DNS server IP address(es). DNS 1 and DNS 2 servers are optional. You can enter another DNS serv-
ers IP address as a backup. DNS 1 and DNS 2 servers will be used when the DNS 1 server fails. Your ISP may require a partic-
ular MAC address in order for you to connect to the Internet. This MAC address is the PCs MAC address that your ISP had originally connected your Internet connection to. Type in this Clone MAC address in this section to replace the WAN MAC address with the MAC address of that PC. Enable Access Control:
Select Services to Block:
Select to enable Access Control function. This lists all defined Services. Select the Services you wish to block. Port Range: For TCP and UDP Services, enter the beginning of the range of port numbers used by the service. If the service uses a single port number, enter it in both the start and finish fields. Protocol: Select the protocol (TCP, UDP or Both) used to the remote system or service. Description: You may key in a description for port range. n o i t c u d o r t n I d n a p u k o o H s g n i t t e S i g n d r o c e R d n a h c r a e S k c a b y a P l t n e i l C m a r g o r P e c n e r e f e R 29 Port Forwarding Enable Port Forwarding:
Check to enable the Port Forwarding function. Servers: Select the server. Local IP Address:
Protocol: Select the protocol (TCP, UDP Enter the Local IP address. or Both) used to the remote system or service. Public Port: Enter a public port number. Private Port: Enter a private port number. Description: You may key in a description for port range. Save: After completing the settings on this page, click Save to save the settings. Reset: Click Reset to restore to default values. Shows the current Port Forwarding information. Current Port Forwarding Table:
Delete Selected: Click to delete selected item. Delete All: Click to delete all listed items. Reset: Click Reset to restore to default values. Note:
If you change the fort number that is registered auto-
matically from the system, you can not monitor using the WAN Save: After completing the settings on this page, click Save to save the settings. Reset: Click Reset to restore to default values. Current Blocked Table:
Note:
If you blocked some port(s), the Netstation may not activate correctly. Denial of Service Setting A DoS (Denial of Service) attack does not attempt to steal data or damage your PCs, but overloads your Internet connection so you cannot use it - the service is therefore unavailable. If DoS function is enabled, DoS attacks will be detect-
ed and blocked. The default is unabled. It is strongly recommended that this setting be left enabled. Enable DoS Prevention:
Enable Source IP Blocking s Block time
(sec) Check to enable the DoS preven-
tion function. Select the item listed to enable. Set the threshold for the frequency of packets that are allowed to pass through. The default value is 50 packets per seconds. You can adjust the value according to your need. It is recommended that you set a practical number so that your network performance wont be hampered. Select All Click to selct all listed items. Clear All Click to clear all listed items. Apply Changes Click to save the current settings. 30 Special Application Some software applications require special or multiple connections to the Internet and these would normally be blocked by the rewall. For example Internet Telephony or Video conferences require multiple connections. So that these special applications can work properly and are not blocked, the rewall needs to be told about them. In each instance there will be a trigger port and incoming port(s), where traf c on the trigger port tells the rewall to open the incoming ports. Special Application allows the router to keep track of outgoing data for speci c port numbers. The router remembers which computer sends out what data, so when the requested data returns through the router, the data is sent back to the proper computer by way of IP address and port mapping rules. You have to rstly check Enable before you can add/
edit an application. Save: Press to save the new settings on the screen. Undo: Press to discard the data you have entered since last time you press Save. Config File This feature allows you to download the current settings from the Wireless Router, and save them to a le on your PC. You can restore a previously downloaded con guration le to the Wireless Router, by uploading it to the Wireless Router. This screen also allows you to set the Wireless Router back to its factory default con guration. Any existing settings will be deleted. Name: Enter the application name. Incoming Type: Select the incoming application Incoming Start Port:
Incoming Finish Port:
type (TCP, UDP or BOTH) Enter a port number as the incoming start port. Enter a port number as the incoming nish port. Trigger Type: Select the trigger type (TCP, Trigger Start Port:
Trigger Finish Port:
UDP or BOTH) Enter a port number as the starting outbound port for the special application de ned in the preceding eld. Enter a port number as the ending outbound port for the special application de ned in the preceding eld. Enable: Mark up to change edit mode. Backup Con g: Use this to download a copy of the current con guration, and store the le on your PC. Click Download to start the download. Restore Con g : This allows you to restore a previously saved con guration le back to the Wireless Router. Click Browse to select the con guration le, then click Restore to upload the con guration le. WARNING !
Uploading a con guration le will destroy (overwrite) ALL of the existing settings. Default Con g: Clicking the Restore Defaults button will reset the Wireless Router to its factory default settings. WARNING ! This will delete ALL of the existing settings. n o i t c u d o r t n I d n a p u k o o H s g n i t t e S i g n d r o c e R d n a h c r a e S k c a b y a P l t n e i l C m a r g o r P e c n e r e f e R 31 Protocol: Select the protocol (TCP, UDP or Both) used to the remote system or service. Description: You may key in a description for the local IP address Current Filter Table: Shows the current lter information. Save: After completing the settings on this page, click Save to save the settings. Reset: Click Reset to restore to default values. MAC Filtering Enable MAC Filtering:
MAC Address:
Check to enable MAC ltering function. Enter the client MAC address. Description: You may key in a description for the MAC address. Shows the current lter information. Current Filter Table:
Save: After completing the settings on this page, click Save to save the settings. Reset: Click Reset to restore to default values. System Log The Logs record various types of activity on the Wireless Router. This data is useful for troubleshooting, but enabling all logs will generate a large amount of data and adversely affect performance. Enable Log: Click to enable log function. Apply Changes: After completing the settings on this page, click Save to save the settings. Refresh: Click to refresh the logs. Clear: Click to delete the logs. IP Filtering Enable IP: Filtering Check to enable the IP ltering function. Local IP Address: Enter the client IP address. 32 URL Filtering Note:
You should reboot the Netstation system after firm-
ware update. Enable URL Filtering:
Check to enable URL ltering function. URL Address: Enter the client URL address. Current Filter Table:
Apply Changes:
Shows the current lter information. After completing the settings on this page, click "Apply Changes"
to con rm the settings. Reset: Click Reset to restore to default values. Upgrade Firmware Browse: Click the Browse button, nd and open the rmware le (the browser will display to correct le path). Start Upgrade: Click the Start Upgrade button to perform Reset: Click Reset to restore to default values. n o i t c u d o r t n I d n a p u k o o H s g n i t t e S i g n d r o c e R d n a h c r a e S k c a b y a P l t n e i l C m a r g o r P e c n e r e f e R 33 Reference Troubleshooting Check the following guide for the possible cause of a problem before contacting service. Symptoms The system power does not turn on. The system power is turned on but no video data is dis-
played on the moni-
tor. The camera num-
bers are displayed on the screen but the camera images are not displayed. The camera video is shown on the screen but the system does not record the video. It is impossible to search through the recorded video. The colors of some camera videos are strange or videos are displayed abnor-
mally. There is a lot of
(screen) noise accompanying the image. Resolutions Check the power cable is connected correctly. Check the input voltage is correct. Check the monitor power cable is connected properly. Make sure the monitor is turned on. Check the video output cable of the Netstation is properly connected to the monitor. Unplug the power cable and plug in again. Check the camera is connected to the Netstation correctly. Check the power cable on the camera is connected correctly. Check there is no problem with the LAN cable connection from the cam-
era to the Netstation. Turn off theNetstation and turn it on again. Check the recording mode in the record setting menu. Check the USB device detection status in the live screen window. Check the recordable disk space in the USB device. If there is no recorded video data, check the recording mode in the record setting menu. Check the user type. The search function is not available for a normal user. If the camera connected to the Netstation has a problem, make sure that the camera is not damaged by trying another camera into a working video output. Check if there is any other problems in only the camera and if there is any other external cause after connecting to other cameras. Check if the LAN cable connection between the camera and the Netstation. Check if there is a high voltage wire around the LAN cable connection between camera and Netstation. It can cause interference and affect video quality. Check the LAN cable connection between the camera and the Netstation is the correct LAN cable. 34 Symptoms Resolutions E-mail reception failed without SMTP server setting. Make sure the network is correctly set. Make sure the mail address is input correctly. Check the spam mail setting of the inputted mail address.
(If you set the spam mail, some mails are deleted automatically or classified in the spam mail box) Some of SMTP mail services do not support an E-mails from private SMTP servers. In this case use the public SMTP server. E-mail reception failed even if the SMTP server was set. When the [Please check the SMTP information or internet cable] message is displayed.
- Check the SMTP server address.
- Check the SMTP port number. (Default setting is 25).
- Check the network settings. When the [Please check the authentication information] message is displayed.
- Check the user name.
- Check the password. The mail reception failed without error message.
- Check the receivers mail address.
- Check your E-mail is not classified as a spam mail on the receiver's mail set-
ting. Check the batteries in the remote control. An E-mail sent from this prod-
uct was not received. The remote control does not work properly. Note:
If you observe any of the following symptoms:
Some of the front panel LEDs do not light. The NetStation does not operate normally. You can reboot the NetStation as follows:
Turn off the NetStation and turn it on again after a few seconds. When the recorder does not work normally after rebooting, contact the service center. n o i t c u d o r t n I d n a p u k o o H s g n i t t e S i g n d r o c e R d n a h c r a e S k c a b y a P l t n e i l C m a r g o r P e c n e r e f e R 35 Recommended devices Supported external USB device list No Maker Model Name Capacity USB Ver. 1 2 3 4 5 6 7 8 FM FM IOCell LG SanDisk Toshiba Hitachi Memorette Memorette CellDisk Xtic Cruzer 2.5" HDD 3.5" HDD 1GB 2GB 1GB 1GB 4GB 80GB 250GB Transcend JF110/JF150 1/2GB 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 Notes:
If the capacity of USB device has under 1GB or over 250GB, the USB device may not operate correctly. If you format the external USB device by using the other unit with NTFS or OS32 file system, the USB device may not be used on this unit. Use the FAT 32 file system for this unit. You can format the USB device as FAT 32 file system by using the format function in the Setup menu of the Netstation. Do not use the USB device via the USB Hub. Check the write speed of the USB and use it more than 2.5 Mbyte/sec write speed. The necessary Capacity for 1Hour recording (Approximatly) Resolution D1 CIF Quality Low Middle High Low Middle High 1ch 113MB 225MB 450MB 56MB 113MB 225MB 2ch 226MB 450MB 900MB 113MB 225MB 450MB 3ch 340MB 675MB 1.35GB 168MB 340MB 675MB 4ch 450MB 900MB 1.8GB 225MB 450MB 900MB Note:
This recording capacity table is only for reference. The recording capacity can be different depending on the recording image. In case of external 250GB HDD, the recording time is approximatly 176hours. 36 Factory default configuration settings 3rd Data Range Default None / USB-Rear / USB-Front None 1st Camera Record 2nd Information Registration Target Media Display Network Rec. Setting Language OSD Dwell Time Wan Port DDNS Sender Mail Receiver Mail Size Format USB Test Type IP Address Subnet Mask Gateway DNS DHCP Main DNS Sub DNS DDNS Provider Domain URL ID Password Mail Send SMTP Server Mail Address Password Address 1 Address 2 Address 3 Address 4 Notification Motion Detect Wireless Disc Full Admin PW Changed Camera Disconnect Wireless SSID Band Channel WEP Key ENG On / Off Off / 2 / 5 / 10 / 30 / 60 sec DHCP / Static / (Others) 0.0.0.0 ~ 255.255.255.255 0.0.0.0 ~ 255.255.255.255 0.0.0.0 ~ 255.255.255.255 On / Off 0.0.0.0 ~ 255.255.255.255 0.0.0.0 ~ 255.255.255.255 On / Off DynDNS / TZO A~Z, 0~9, Special Character A~Z, 0~9, Special Character A~Z, 0~9, Special Character On / Off A~Z, 0~9, Special Character A~Z, 0~9, Special Character A~Z, 0~9, Special Character A~Z, 0~9, Special Character A~Z, 0~9, Special Character A~Z, 0~9, Special Character A~Z, 0~9, Special Character On / Off On / Off On / Off On / Off On / Off A~Z, 0~9 2.4GHz (B+G) / 2.4GHz (G) Auto / 1 ~ 11 Off, a ten digit numbers (HEX code) ENG On Off DHCP Null Null Null On Null Null Off DynDNS Null Null Null Off Null Null Null Null Null Null Null Off Off Off Off On HMS-AP-xxxx 2.4GHz (G) Auto Off n o i t c u d o r t n I d n a p u k o o H s g n i t t e S i g n d r o c e R d n a h c r a e S k c a b y a P l t n e i l C m a r g o r P e c n e r e f e R 37 1st System 2nd Clock User Password Auto Log Out Beep 3rd Clock Mode Date Time NTP Server Time Zone Daylight Saving Admin Normal Data Range Auto / Manual YYYY / MM / DD HH : MM North America 1~3 / Europe 1~2 / Australia / Asia Pacific GMT-12 ~ GMT+12 On / Off 4~8 digit number 4~8 digit number Off / 5 /10 / 30 / 60 min On / Off Default Manual Current Date Current Time North America 1 GMT Off Null 0000 Off Off Factory Reset Reset 38 Specifications Video Audio Motion Recording ITEM Video Format Input Output Composite VGA Resolution Input Output Intput Noti cation to e-mail Frame Rate (/Sec) Recording Mode Storage Search / Playback Playback Control Mode Display Search Mode Division Mode Motion Alert Mode Language Menu Screen Information Pan/Tilt Angle Zoom Auto Sequence mode LAN Network Wireless
(IEEE802.11b/g) User Number of ports Connector type Physical Transmission protocol
(802.11g) Transmission protocol
(802.11b) Transmission speed (802.11g) Transmission speed (802.11b) Frequency range (MHz) Number of channels RESET button Mode switch LSP-W1000 NTSC / PAL 4 1 1 640x480, 320x240 4 1 OK OK Max. 7.5 VGA Frames/Sec/Ch Continuous / Motion / Instant Record Ext. USB Storage Normal / Still / Stop Fast / Slow Forward Fast / Slow Backward Date / Time / File 1 / 4 Buzzer English GUI OK Pan: -50 to +50, Tilt: -40 to +10 Digital X4, 5 Steps OK 4 Ethernet RJ-45 100Base-TX/10Base-T DS-SS, OFDM DS-SS 54/48/36/24/18/12/9/6 Mbps 11/5.5/2/1 Mbps
(2.412 - 2.484 GHz)
(1~14 ch ) OK OK n o i t c u d o r t n I d n a p u k o o H s g n i t t e S i g n d r o c e R d n a h c r a e S k c a b y a P l t n e i l C m a r g o r P e c n e r e f e R 39 Security I/O Etc General ITEM WEP Encryption wireless stealth functionality MAC address ltering User Level Control Front Rear LED USB RCU sensor DC In RCA Jack D-Sub RJ-45 DIP Switch USB RESET button Antenna Password Protection Password Reset Log List Web Client Button Lock Buzzer Video Codec Audio Codec Power Source Power Consumption Dimension (WxDxH mm) Weight Operation Humidity Operation Temp. LSP-W1000 64/128Bit ESSID OK OK 10 1 port 1 1 1 Audio / 1 Video VGA Video 5 2 1 1 1 OK OK OK OK OK OK MPEG4 G.726 DC Adapter 40 P/NO: MFL3????
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2007-10-03 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2007-10-03
|
||||
1 | Applicant's complete, legal business name |
LG Electronics USA
|
||||
1 | FCC Registration Number (FRN) |
0023476120
|
||||
1 | Physical Address |
1000 Sylvan Avenue
|
||||
1 |
Englewood Cliffs, New Jersey 07632
|
|||||
1 |
United States
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
m******@ccsemc.com
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
BEJ
|
||||
1 | Equipment Product Code |
9QK-W1000NS
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
K**** H******
|
||||
1 | Title |
Director, Standards & Compliance
|
||||
1 | Telephone Number |
201-4********
|
||||
1 | Fax Number |
201-8********
|
||||
1 |
k******@lge.com
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
ESTECH CO., LTD.
|
||||
1 | Name |
J****** Y******
|
||||
1 | Physical Address |
97-1 Hoiuk-Ri Majang-Myon
|
||||
1 |
Icheon-city, KyungKi-Do, 467-811
|
|||||
1 |
South Korea
|
|||||
1 | Telephone Number |
82-31********
|
||||
1 |
j******@estech.co.kr
|
|||||
app s | Non Technical Contact | |||||
1 | Firm Name |
ESTECH CO., LTD.
|
||||
1 | Name |
J**** Y********
|
||||
1 | Physical Address |
97-1 Hoiuk-Ri Majang-Myon
|
||||
1 |
Icheon-city, KyungKi-Do, 467-811
|
|||||
1 |
South Korea
|
|||||
1 | Telephone Number |
82-31********
|
||||
1 |
j******@estech.co.kr
|
|||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DTS - Digital Transmission System | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Home Monitoring System | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Power output listed is conducted. The antenna(s) used for this device must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
ESTECH Co., Ltd.
|
||||
1 | Name |
Y****** J******
|
||||
1 | Telephone Number |
82-31********
|
||||
1 | Fax Number |
82-31********
|
||||
1 |
j******@estech.co.kr
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 28 | 2412.00000000 | 2462.00000000 | 0.0410000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC