FCC ID: BEJ32LG70UA LCD TV/MONITOR

 

LCD TV OWNERS MANUAL PLASMA TV PLASMA TV MODELS 42PG25 50PG25 50PG60 60PG60 50PG70 60PG70 LCD TV MODELS 37LG50 32LG30 42LG50 37LG30 47LG50 42LG30 42LGX 52LG50 32LG70 42LG70 47LG70 52LG70 32LG60 37LG60 42LG60 47LG60 52LG60 47LG90 Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service. P/NO : SAC30708020 (0804-REV05) www.lgusa.com / www.lg.ca ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency (EPA). As an ENERGY STAR Partner LG Electronics USA, Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. WARNING / CAUTION WARNING / CAUTION To prevent fire or shock hazards, do not expose this product to rain or moisture. FCC NOTICE Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the litera-

ture accompanying the appliance. WARNING/CAUTION TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE TO CABLE/TV INSTALLER CAUTION This reminder is provided to call the CATV system installers attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the users authority to operate this product 1 SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the apparatus. This information shall be given in a language acceptable to the country where the apparatus is intended to be used. The important safety instructions shall be entitled Important Safety Instructions. The following safety instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by adding statements after the end of the following safety instruction list. At the manufacturers option, a picture or drawing that illustrates the intent of a specific safety instruction may be placed immediately adjacent to that safety instruction:

Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. 1 2 Do not use this apparatus near water. Clean only with dry cloth. 3 Do not block any ventilation openings. Install in accordance with the manufacturers instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers)that produce heat. When mounting a TV it on the wall, make sure not to install TV by the hanging power and sig-

nal cables on the back of the TV. 4 5 2 6 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 7 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 8 Only use attachments/accessories specified by the manufacturer. 9 Unplug this apparatus during lighting storms or when unused for long periods of time. 10 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Never touch this apparatus or antenna during a thunder or lighting storm. 15 11 12 13 14 Do not allow a impact shock or any objects to fall into the product, and do not drop onto the screen with something. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has exposed to rain or moisture, does not operate normally, or has been dropped. CAUTION concerning the Power Cord :

Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates dam-

age or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. Outdoor use marking :

WARNING - To reduce the risk of fire or elec-

tric shock, do not expose this appliance to rain or moisture. 16 Wet Location Marking : Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on or over apparatus. 17 GROUNDING Ensure that you connect the earth ground wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes. Power Supply Short-circuit Breaker 18 DISCONNECTING DEVICE FROM MAINS Mains plug is the disconnecting device. The plug must remain readily operable. 3 CONTENTS WARNING / CAUTION . 1 Channel Setup SAFETY INSTRUCTIONS . 2 FEATURE OF THIS TV . 6 PREPARATION Accessories . 7 Front Panel Information . 8 Back Panel Information . 10 Stand Installation . 14 Cable Management . 16 Desktop Pedestal Installation . 18 Swivel Stand . 18 Attaching the TV to a Desk . 18 VESA Wall Mounting . 19 Protection Cover . 20 Securing the TV to the wall to prevent falling . 21 Antenna or Cable Connection . 22 EXTERNAL EQUIPMENT SETUP HD Receiver Setup . 23 DVD Setup . 29 VCR Setup . 33 Other A/V Source Setup . 36 PC Setup . 37 USB Connection . 46 Audio Out Connection . 47 WATCHING TV / CHANNEL CONTROL Remote Control Functions . 48 Turning On the TV . 50 Channel Selection . 50 Volume Adjustment . 50 Quick Menu . 51 Initial Setting . 52 On-Screen Menus Selection . 54

- Auto Scan (Auto Tuning) . 56

- Add / Delete Channel (Manual Tuning) . 57

- Channel Editing . 58 Input List . 59 Input Label . 60 AV Mode . 61 SIMPLINK . 62 USB Entry Modes . 64 Photo List . 65 Music List . 69 PICTURE CONTROL Picture Size (Aspect Ratio) Control . 72 Preset Picture Settings

- Picture Mode - Preset . 74

- Color Tone - Preset . 75 Manual Picture Adjustment

- Picture Mode - User Mode . 76

- Picture Mode - Expert Control . 77 Picture Improvement Technology . 78 Advanced Control - Black (Darkness) Level . 79 Advanced Control - Eye Care . 80 Advanced Control - Real Cinema/Film Mode . 81 Advanced Control - TruMotion . 82 TruMotion Demo . 83 Picture Reset . 84 Power Indicator . 85 Image Sticking Minimization (ISM) Method . 86 Power Saving Picture Mode . 87 4 SOUND & LANGUAGE CONTROL APPENDIX Troubleshooting . 118 Maintenance . 120 Product Specifications . 121 Programming the Remote Control . 124 IR Codes . 127 External Control Through RS-232C . 129 Open Source License . 136 Auto Volume Leveler (Auto Volume) . 88 Preset Sound Settings (Sound Mode) . 89 Sound Setting Adjustment - User Mode . 90 Clear Voice . 91 Balance . 92 TV Speakers On/Off Setup . 93 Audio Reset . 94 Stereo/SAP Broadcast Setup . 95 Audio Language . 96 On-Screen Menus Language Selection . 97 Caption Mode

- Analog Broadcasting System Captions . 98

- Digital Broadcasting System Captions . 99

- Caption Option . 100 TIME SETTING Clock Setting

- Auto Clock Setup . 101

- Manual Clock Setup . 102 Auto On/Off Time Setting . 103 Sleep Timer Setting . 104 Auto Shut-off Setting . 105 PARENTAL CONTROL / RATINGS Set Password & Lock System . 106 Channel Blocking . 109 Movie & TV Rating . 110 Downloadable Rating . 115 External Input Blocking . 116 Key lock . 117 5 FEATURE OF THIS TV is a trademark of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. FOR LCD TV If the TV feels cold to the touch, there may be a small flicker when it is turned on. This is normal, there is nothing wrong with TV. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen. On Disposal (Only Hg lamp used LCD TV) The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority. 6 PREPARATION ACCESSORIES Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV. The accessories included may differ from the images below. T V S T B Q. M E N U P O W E R D V D V C R IN P U T M E N U E N T E R A V M O D E R E T U R N V O L F A V 1 MUTE 4 2 C H P A G E 7 5 3 8 6 0 9 FLASHBK 1.5V 1.5V Remote Control, Batteries Option Extras D-sub 15 pin Cable Power Cord When using the VGA (D-sub 15 pin cable) PC connection, the user must use shielded signal interface cables with ferrite cores to maintain standards compliance.

(Only 50PG25, 50/60PG60, 50/60PG70) Owners Manual CD Manual Copyright 2007 LGE, All Rights Reserved.

* Wipe spots on the exterior only with the polishing cloth.

* Do not wipe roughly when removing stain. Excessive pressure may cause scratch or discoloration. Polishing Cloth

(This feature is not available for all models.) For Plasma TV models

(Only 42PG25) x 4 Bolts for stand assembly

(Refer to P.14) For LCD TV models Cable Holder Cable Management Clip Protection Cover

(Refer to P.20) 32/37/42LG30, 37/42/47/52LG50, 32/42/47/52LG70, 47LG90

(Only 32/37/42LG30, 37/42LG50, 32/42LG70) x 4 x 4

(Only 32LG30/70, 42LG30/50) or Bolts for stand assembly Screw for stand fixing

(Refer to P.14)

(Refer to P.18) Protection Cover

(Refer to P.20) 32/37/42/47/52LG60, 42LGX

(Only 32/37LG60)

(Only 42LG60, 42LGX) or 32LG60: 3EA 37LG60: 4EA 4EA 2EA

(M4x16) 1EA 4EA

(M4x20) Bolts for stand assembly

(Refer to P.15) Protection Cover

(Refer to P.20) Cable Management Clip P R E P A R A T O N I 7 PREPARATION FRONT PANEL INFORMATION Image shown may differ from your TV. NOTE: If your TV has a protection tape attached, remove the tape. And then wipe the TV with a cloth (If a polishing cloth is included with your TV, use it). Plasma TV Models Remote Control Sensor POWER Button Power/Standby Indicator Illuminates red in standby mode. Illuminates blue when the TV is switched on. INPUT MENU ENTER VOL CH INPUT Button MENU Button ENTER Button VOLUME

(-, +) Buttons CHANNEL

(EE,D)Buttons LCD TV Models 32/42/47/52LG70, 47LG90 Intelligent Sensor Adjusts picture according to the surrounding conditions Power/Standby Indicator Illuminates red in standby mode. Illuminates blue when the set is switched on.

(Can be adjusted using Power Indicator in the OPTION menu. G p.85) Remote Control Sensor POWER Button CH CHANNEL (

Buttons

) VOL ENTER MENU INPUT VOLUME (+, -) Buttons ENTER Button MENU Button INPUT Button P R E P A R A T O N I 8 LCD TV Models 32/37/42LG30, 37/42/47/52LG50 Intelligent Sensor (Except 32/37/42LG30) Adjusts picture according to the surrounding conditions Power/Standby Indicator Illuminates red in standby mode. Illuminates blue when the set is switched on.

(Can be adjusted using Power Indicator in the OPTION menu. G p.85) Remote Control Sensor POWER Button 32/37/42/47/52LG60, 42LGX Intelligent Sensor Adjusts picture according to the surrounding conditions. POWER Button Remote Control Sensor Power/Standby Indicator Illuminates red in standby mode. Illuminates white when the set is switched on.

(Can be adjusted using Power Indicator in the OPTION menu. G p.85) CH VOL ENTER MENU INPUT CH VOL ENTER MENU INPUT CHANNEL (

Buttons

) VOLUME (+, -) Buttons ENTER Button MENU Button INPUT Button CHANNEL (

Buttons

) VOLUME (+, -) Buttons ENTER Button MENU Button INPUT Button P R E P A R A T O N I 9 PREPARATION BACK PANEL INFORMATION Image shown may differ from your TV. Plasma TV Models 12 10 1 9 N I B S U 4 N I I M D H R I O D U A O N O M L

O E D V I AV IN 2 1 3 RGB IN HDMI/DVI IN RGB(PC) 5 4 ANTENNA/

CABLE IN AUDIO

(RGB/DVI) REMOTE CONTROL IN DIGITAL AUDIO OUT OPTICAL COAXIAL 6 7 3 2 1 2 1 COMPONENT IN RS-232C IN

(CONTROL & SERVICE) AUDIO OUT O E D V S

I AUDIO VIDEO

) MONO VIDEO AUDIO 2 8 9 1 N I V A P R E P A R A T O N I 10 LCD TV Models 32/37/42LG30 1 HDMI/DVI IN 2 1 37/42/47/52LG50 1 HDMI/DVI IN 2 1 2 1 2 1 12 3 RGB IN RGB(PC) 5 4 ANTENNA/

CABLE IN 6 AUDIO

(RGB/DVI) REMOTE CONTROL IN DIGITAL AUDIO OUT OPTICAL 7 RS-232C IN

(CONTROL & SERVICE) AUDIO OUT 8 9 1 N I V A VIDEO COMPONENT IN AUDIO S-VIDEO 2 VIDEO MONO

) AUDIO 3 RGB IN RGB(PC) 5 4 ANTENNA/

CABLE IN 6 AUDIO

(RGB/DVI) REMOTE CONTROL IN DIGITAL AUDIO OUT OPTICAL COAXIAL 7 RS-232C IN

(CONTROL & SERVICE) AUDIO OUT VIDEO COMPONENT IN AUDIO S-VIDEO 2 VIDEO MONO

) AUDIO 8 9 1 N I V A 11 1 9 10 1 9 P R E P A R A T O N I 11 B S U Y L N O E C U V R E S 3 N I I M D H R I O D U A O N O M L

O E D V I AV IN 2 N I B S U 3 N I I M D H R I O D U A O N O M L

O E D V I AV IN 2 PREPARATION Image shown may differ from your TV. LCD TV Models P R E P A R A T O N I 12 32/42/47/52LG70, 47LG90 1 HDMI/DVI IN 3 RGB IN RGB(PC) 5 4 ANTENNA/

CABLE IN 6 AUDIO

(RGB/DVI) REMOTE CONTROL IN DIGITAL AUDIO OUT OPTICAL COAXIAL 7 3 2 1 RS-232C IN

(CONTROL & SERVICE) AUDIO OUT 2 1 VIDEO COMPONENT IN AUDIO 2 1 N I V A S-VIDEO VIDEO MONO

) AUDIO 8 9 10 1 9 N I B S U 4 N I I M D H R I O D U A O N O M L

O E D V I AV IN 2 12 32/37/42/47/52LG60, 42LGX 21 N I T N E N O P M O C O E D V I I O D U A 2 11 RS-232C IN

(SERVICE ONLY) REMOTE CONTROL IN 4 1 2 DIGITAL AUDIO OUT COAXIAL 3 AUDIO

(RGB/DVI) OPTICAL RGB(PC) ANTENNA/

CABLE IN 7 6 12 N I I V D

I M D H N I B G R 1 3 10 1 9 N I B S U 4 N I I M D H R I O D U A O N O M L

O E D V I AV IN 1 2 3 4 5 6 7 AUDIO OUT Analog audio output for use with amps and home theater systems. AV (Audio/Video) IN Analog composite connection. Supports standard definition video only (480i). S-VIDEO Better quality than standard composition. Supports standard definition video only (480i). 10 USB INPUT Used for viewing photos and listening to MP3s. 11 12 USB SERVICE ONLY or RS-232C IN (SERVICE ONLY) Used for software updates. Power Cord Socket For operation with AC power. Caution: Never attempt to operate the TV on DC power. HDMI/DVI IN, HDMI IN Digital Connection. Supports HD video and Digital audio. Doesnt support 480i. Accepts DVI video using an adapter or HDMI to DVI cable (not included). 8 9 COMPONENT IN Analog Connection. Supports HD. Uses a red, green, and blue cable for video & red and white for audio. RGB (PC) Analog PC Connection. Uses a D-sub 15 pin cable

(VGA cable). AUDIO (RGB/DVI) 1/8 headphone jack for analog PC audio input. REMOTE CONTROL IN PORT For a wired remote control. RS-232C IN (CONTROL & SERVICE) PORT Used by third party devices. ANTENNA/CABLE IN Connect over-the air signals to this jack. Connect cable signals to this jack. DIGITAL AUDIO OUT Digital audio output for use with amps and home theater systems. Includes an optical and/or coaxial connection. Note: In standby mode, these ports do not work. P R E P A R A T O N I 13 PREPARATION STAND INSTALLATION Image shown may differ from your TV. When assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully, the prod-

uct can tilt forward after the product installation). If you tighten the bolt with excessive force, the bolt can devi-

ate from abrasion of the tightening part of the bolt. You can remove the stand before installing the TV on a wall mount by performing the stand instructions in reverse. Only 42PG25 Only 32/37/42LG30, 37/42LG50, 32/42LG70, 1 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. 1 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. P R E P A R A T O N I 2 Assemble the TV as shown. 2 Assemble the parts of the STAND BODY with COVER BASE of the TV. STAND BODY COVER BASE 3 Fix the 4 bolts securely using the holes in the back of the TV. 3 Assemble the TV as shown. 4 Fix the 4 bolts securely using the holes in the back of the TV. 14 Only 32/37/42LG60, 42LGX 1 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. 2 Assemble the parts of the STAND BODY with COVER BASE of the TV. 32LG60 37LG60 42LG60, 42LGX STAND BODY STAND BODY

(M4x16) STAND BODY COVER BASE COVER BASE COVER BASE 3 Assemble the TV as shown. 4 Fix the 4 bolts securely using the holes in the back of the TV.

(M4x20) P R E P A R A T O N I 15 PREPARATION STAND DETACHMENT PROTECTION COVER Image shown may differ from your TV. Image shown may differ from your TV. 1 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. You can remove the stand before installing the TV on a wall mount by performing the previous stand instruc-

tions in reverse. After removing the stand, install the included protection cover over the hole for the stand. Press the PROTECTION COVER into the TV until you hear it click. Plasma TV Models 2 Loose the bolts from TV. 47/52LG50/70 47/52LG60 LCD TV Models 50PG25/60 60PG60 2 Detach the stand from TV. After removing the protection paper from the protection cover, adhere it to the TV as shown. P R E P A R A T O N I 16 VESA WALL MOUNTING Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest dealer. If installed on a ceiling or slanted wall, it may fall and result in severe personal injury. We recommend that you use an LG brand wall mount when mounting the TV to a wall. A B Product Model VESA Standard Screw Quantity 32LG30, 32LG60, 32LG70 200 * 100 37LG30, 37LG60, 37LG50 LCD TV 42LG30, 42LG50, 42LG60, 42LG70, 42LGX 47LG50, 47LG60, 47LG70, 47LG90 200 * 200 52LG50, 52LG60, 52LG70 42PG25 50PG25, 50PG60, 50PG70 60PG60, 60PG70 800 * 400 400 * 400 600 * 400 PLASMA TV

NOTE M4 M6 M6 M6 M8 4 4 4 4 4 G Screw length needed depends on the wall mount used. For further information, refer to the instruc-

tions included with the mount. G Standard dimensions for wall mount kits are shown in the table. GG When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly are provided. GG Do not use screws longer then the standard dimen-

sion, as they may cause damage to the inside to the TV. G For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ depending on their specifica-

tions. G Do not use screws that do not comply with the VESA standard screw specifications. Do not use fasten the screws too strongly, this may damage the TV or cause the TV to a fall, leading to personal injury. LG is not liable for these kinds of accidents. G LG is not liable for TV damage or personal injury when a non-VESA or non specified wall mount is used or the consumer fails to follow the TV installa-

tion instructions. CAUTION G Do not install your wall mount kit while your TV is turned on. It may result in personal injury due to electric shock. P R E P A R A T O N I 17 PREPARATION CABLE MANAGEMENT Image shown may differ from your TV. Plasma TV Models 1 Connect the cables as necessary. To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section. P R E P A R A T O N I 2 Install the CABLE MANAGEMENT CLIP as shown. If your TV has the CABLE HOLDER, install it as shown and bundle the cables. CABLE HOLDER CABLE MANAGEMENT CLIP How to remove the CABLE MANAGEMENT CLIP 42PG25 50PG25, 50/60PG60, 50/60PG70 G First, press the cable management. Hold the CABLE MANAGEMENT CLIP with both hands and pull it upward. G Hold the CABLE MAN-

AGEMENT CLIP with both hands and pull it upward. G Separate CABLE MAN-

AGEMENT CLIP from TV by pressing two latches. NOTE

G Do not hold the CABLE MANAGEMENT CLIP when moving the TV.

- If the TV is dropped, you may be injured or the product may be broken. 18 LCD TV Models 32/37/42LG30, 37/42/47/52LG50, 32/42/47/52LG70, 47LG90 1 Connect the cables as necessary. To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section. 32/37/42/47/52LG60, 42LGX 1 Align the hole with the tab on the CABLE MANAGEMENT CLIP. Turn the CABLE MANAGEMENT CLIP as shown. Note: This cable management clip can be bro-

ken by excessive pressure. P R E P A R A T O N I 2 Install the CABLE MANAGEMENT CLIP as shown. CABLE MANAGEMENT CLIP 3 Put the cables inside the CABLE MANAGEMENT CLIP and snap it closed. 2 Connect the cables as necessary. To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section. 19 PREPARATION DESKTOP PEDESTAL INSTALLATION Image shown may differ from your TV. For proper ventilation, allow a clearance of 4 inches on all four sides from the wall. 4 inches 4 inches 4 inches 4 inches CAUTION G Ensure adequate ventilation by following the clearance recommendations. GG Do not mount near or above any type of heat source. SWIVEL STAND After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit your viewing position. ATTACHING THE TV TO A DESK (Only 32LG30/70, 42LG30/50) The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. Stand Desk 1-Screw

(provided as parts of the product) WARNING G To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury. P R E P A R A T O N I 20 SECURING THE TV TO THE WALL TO PREVENT FALLING You should purchase necessary components to prevent TV from falling off of the stand. Image shown may differ from your TV. We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children dont climb on or hang from the TV. P R E P A R A T O N I Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.

* If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.

* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes. Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately) to the wall. Match the height of the bracket that is mounted on the wall to the holes in the product. Ensure the eye-bolts or brackets are tightened securely. Use a sturdy rope (not provided as parts of the product, must pur-

chase separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product. NOTE

G Use a platform or cabinet strong enough and large enough to support the size and weight of the TV. G To use the TV safely make sure that the height of the bracket on the wall and the one on the TV are the same. 21 PREPARATION To prevent damage do not connect to the power outlet until all connections are made between the devices. ANTENNA OR CABLE CONNECTION 1. Antenna (Analog or Digital) Wall Antenna Socket or Outdoor Antenna without a Cable Box Connection. For optimum picture quality, adjust the antenna direction if needed. Wall Antenna Socket Outdoor Antenna

(VHF, UHF) 2. Cable Cable TV Wall Jack Multi-family Dwellings/Apartments

(Connect to wall antenna socket) ANTENNA/

CABLE IN RF Coaxial Wire (75 ohm) Single-family Dwellings /Houses

(Connect to wall jack for outdoor antenna) Copper Wire Be careful not to bend the copper wire when connecting the antenna. RF Coaxial Wire (75 ohm) ANTENNA/

CABLE IN To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly. If the antenna needs to be split for two TVs, install a 2-Way Signal Splitter. If the antenna is not installed properly, contact your dealer for assistance. P R E P A R A T O N I 22 EXTERNAL EQUIPMENT SETUP To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment. Image shown may differ from your TV. HD RECEIVER SETUP This TV can receive digital over-the-air/digital cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device. Component Connection 1. How to connect 1 Connect the video outputs (Y, PB, PR) of the digital set-

top box to the COMPONENT IN VIDEO 1 jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red). 2 Connect the audio output of the digital set-top box to the COMPONENT IN AUDIO 1 jacks on the TV. 2. How to use Turn on the digital set-top box.

(Refer to the owners manual for the digital set-top box. operation) Select the Component 1 input source on the TV using the INPUT button on the remote control. If connected to COMPONENT IN2 input, select the Component 2 input source on the TV. Supported Resolutions Signal 480i 480p 720p 1080i 1080p Component HDMI Yes Yes Yes Yes Yes No Yes Yes Yes Yes Y, CB/PB, CR/PR Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) 720x480i 720x480p 1280x720p 1920x1080i 1920x1080p 15.73 15.73 31.47 31.50 44.96 45.00 33.72 33.75 26.97 27.00 33.71 33.75 67.432 67.50 59.94 60.00 59.94 60.00 59.94 60.00 59.94 60.00 23.976 24.00 29.97 30.00 59.94 60.00 E X T E R N A L E Q U I P M E N T S E T U P 23 EXTERNAL EQUIPMENT SETUP Plasma TV, 32/37/42LG30, 37/42/47/52LG50, 32/42/47/52LG70, 47LG90 Y PB PR L R E X T E R N A L E Q U I P M E N T S E T U P 24 1 2 RGB IN RGB(PC) AUDIO

(RGB/DVI) REMOTE CONTROL IN DIGI OPT RS-232

(CONTROL &

2 1 Y PB PR L R VIDEO COMPONENT IN AUDIO S-VIDEO 32/37/42/47/52LG60, 42LGX 21 N I I V D

I I B G R M D 3 H AUDIO N

(RGB/DVI) 1 2 DIGITAL AUDIO OUT COAXIAL OPTICAL RGB(PC) ANTENNA/

CABLE IN N I T N E N O P M O C O E D V I I O D U A RS-232C IN

(SERVICE ONLY) REMOTE CONTROL IN 1 2 L R Y PB PR HDMI Connection 1. How to connect 1 2 Connect the digital set-top box to HDMI/DVI IN1, 2, 3, or 4 jack on the TV. No separate audio connection is necessary. HDMI supports both audio and video. 2. How to use Turn on the digital set-top box.

(Refer to the owners manual for the digital set-top box.) Select the HDMI1, HDMI2, HDMI3, or HDMI4 input source on the TV using the INPUT button on the remote control. HDMI-DTV Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) 720x480p 1280x720p 1920x1080i 1920x1080p 31.47 31.50 44.96 45.00 33.72 33.75 26.97 27.00 33.71 33.75 67.432 67.50 59.94 60.00 59.94 60.00 59.94 60.00 23.976 24.00 29.97 30.00 59.939 60.00 E X T E R N A L E Q U I P M E N T S E T U P 25 EXTERNAL EQUIPMENT SETUP 32/37/42LG30, 37/42/47/52LG50 Plasma TV, 32/42/47/52LG70, 47LG90 RGB IN RGB(PC) A

(RG HDMI/DVI IN 2 1 2 1 Y PB PR VIDEO COMPONENT HDMI/DVI IN RGB IN RGB(PC) 3 2 1 Y PB PR VIDEO COMPON 1 1 HDMI-DTV OUTPUT HDMI-DTV OUTPUT 32/37/42/47/52LG60, 42LGX 21 1 2 DIGITAL AUDIO OUT COAXIAL 3 AUDIO

(RGB/DVI) OPTICAL RGB(PC) ANTENNA/

CABLE IN N I T N E N O P M O C O E D V I I O D U A RS-232C IN

(SERVICE ONLY) REMOTE CONTROL IN 1 HDMI-DTV OUTPUT N I I V D

I M D H N I B G R E X T E R N A L E Q U I P M E N T S E T U P 26 DVI to HDMI Connection 1. How to connect 1 2 32/37/42LG30, 37/42/47/52LG50, Plasma TV

- Connect the DVI output of the digital set-top box to the HDMI/DVI IN 1, 2, or 3 jack on the TV. 32/37/42/47/52LG60, 32/42/47/52LG70, 42LGX, 47LG90

- Connect the DVI output of the digital set-top box to the HDMI/DVI IN 1, 2, 3, or 4 jack on the TV. Connect the PC audio output to the AUDIO (RGB/DVI) jack on the TV. 2. How to use Turn on the digital set-top box. (Refer to the owners manual for the digital set-top box.) 32/37/42LG30, 37/42/47/52LG50, Plasma TV

- Select the HDMI1, HDMI2, or HDMI3 input source on the TV using the INPUT button on the remote control. 32/37/42/47/52LG60, 32/42/47/52LG70, 42LGX, 47LG90

- Select the HDMI1, HDMI2, HDMI3, or HDMI4 input source on the TV using the INPUT button on the remote control.

NOTE G A DVI to HDMI cable or adapter is required for this connection. DVI doesn't support audio, so a separate audio connection is necessary. E X T E R N A L E Q U I P M E N T S E T U P 27 EXTERNAL EQUIPMENT SETUP 32/37/42LG30, 37/42/47/52LG50 Plasma TV, 32/42/47/52LG70, 47LG90 RGB IN RGB(PC) AUDIO

(RGB/DVI) REMOTE CONTROL IN HDMI/DVI IN R

(CONT Y PB PR L R VIDEO COMPONENT IN AUDIO S 3 2 1 RGB IN RGB(PC) AUDIO

(RGB/DVI) REMOT CONTROL Y PB PR 2 1 L R VIDEO COMPONENT IN AUDIO

1 N I V A 2 1 2 HDMI/DVI IN 2 1 2 1 1 E X T E R N A L E Q U I P M E N T S E T U P DVI-DTV OUTPUT L R DVI-DTV OUTPUT L R N I I V D

I M D H N I B G R 32/37/42/47/52LG60, 42LGX 21 1 2 3 DIGITAL AUDIO OUT COAXIAL AUDIO

(RGB/DVI) OPTICAL RGB(PC) ANTENNA/

CABLE IN 1 N I T N E N O P M O C O E D V I 2 I O D U A RS-232C IN

(SERVICE ONLY) REMOTE CONTROL IN 28 DVI-DTV OUTPUT L R DVD SETUP Component Connection 1. How to connect 1 Connect the video outputs (Y, PB, PR) of the DVD to the COMPONENT IN VIDEO1 jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red). 2 Connect the audio outputs of the DVD to the COMPONENT IN AUDIO1 jacks on the TV. 2. How to use Turn on the DVD player, insert a DVD. Select the Component 1 input source on the TV using the INPUT button on the remote control. If connected to COMPONENT IN 2 input, select the Component 2 input source on the TV. Refer to the DVD player's manual for operating instructions. Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below. Component ports on the TV Video output ports on DVD player Y Y Y Y Y PB PB B-Y Cb Pb PR PR R-Y Cr Pr E X T E R N A L E Q U I P M E N T S E T U P 29 EXTERNAL EQUIPMENT SETUP Plasma TV, 32/37/42LG30, 37/42/47/52LG50, 32/42/47/52LG70, 47LG90 Y PB PR L R E X T E R N A L E Q U I P M E N T S E T U P 30 1 2 RGB IN RGB(PC) AUDIO

(RGB/DVI) REMOTE CONTROL IN DIGITA OPTICA RS-232C I

(CONTROL & SER 2 1 Y PB PR L R VIDEO COMPONENT IN AUDIO S-VIDEO 32/37/42/47/52LG60, 42LGX 21 N I I V D

I I B G R M D 3 H AUDIO N

(RGB/DVI) 1 2 DIGITAL AUDIO OUT COAXIAL OPTICAL RGB(PC) ANTENNA/

CABLE IN N I T N E N O P M O C O E D V I I O D U A RS-232C IN

(SERVICE ONLY) REMOTE CONTROL IN 1 2 L R Y PB PR S-Video Connection (Except 32/37/42/47/52LG60, 42LGX) 1. How to connect 1 2 Connect the S-VIDEO output of the DVD to the S -VIDEO input on the TV. Connect the audio outputs of the DVD to the AUDIO input jacks on the TV. 2. How to use Turn on the DVD player, insert a DVD. Select the A V 1 input source on the TV using the INPUT button on the remote control. Refer to the DVD player's manual for operating instructions. S-VIDEO AUDIO L R ANTENNA/

CABLE IN UDIO B/DVI) REMOTE CONTROL IN 2 1 DIGITAL AUDIO OUT OPTICAL COAXIAL RS-232C IN

(CONTROL & SERVICE) AUDIO OUT L R AUDIO N S-VIDEO VIDEO L

(MONO) AUDIO R 1 N I V A E X T E R N A L E Q U I P M E N T S E T U P 31 EXTERNAL EQUIPMENT SETUP HDMI Connection 1. How to connect 1 2 Connect the HDMI output of the DVD to the HDMI/DVI IN1, 2, 3 or 4 jack on the TV. No separate audio connection is necessary. HDMI supports both audio and video. 2. How to use Select the HDMI1, HDMI2, HDMI3, or HDMI4 input source on the TV using the INPUT button on the remote control. Refer to the DVD player's manual for operating instructions. 32/37/42LG30, 37/42/47/52LG50 RGB(PC) U O

(RGB/D 2 1 Y PB PR L VIDEO COMPONENT IN A HDMI/DVI IN 2 1 1 HDMI-DVD OUTPUT N I I V D

I M D H N I B G R Plasma TV, 32/42/47/52LG70, 47LG90 32/37/42/47/52LG60, 42LGX HDMI/DVI IN RGB IN RGB(PC) 3 2 1 Y PB PR

(R 2 1 VIDEO COMPONENT 1 HDMI-DVD OUTPUT 21 N I T N E N O P M O C O E D V I I O D U A 1 2 DIGITAL AUDIO OUT COAXIAL 3 AUDIO

(RGB/DVI) OPTICAL RGB(PC) ANTENNA/

CABLE IN RS-232C IN

(SERVICE ONLY) 1 REMOTE CONTROL IN HDMI-DVD OUTPUT E X T E R N A L E Q U I P M E N T S E T U P 32 VCR SETUP To avoid picture noise (interference), leave an adequate distance between the VCR and TV. Use the ISM feature in the Option menu to avoid having a fixed image remain on the screen for a long period of time (Plasma TV models only). If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen. This phenomenon is common to all TVs and is not covered by warranty. Antenna Connection 1. How to connect Plasma TV, 32/37/42LG30, 37/42/47/52LG50, 32/42/47/52LG70, 47LG90 1 2 Connect the RF antenna out socket of the VCR to the ANTENNA/CABLE IN sock-

et on the TV. ANTENNA/

CABLE IN UDIO OUT COAXIAL 1 Connect the antenna cable to the RF antenna in socket of the VCR. AUDIO OUT E) 2. How to use Set VCR output switch to 3 or 4 and then EO L

(MONO) AUDIO R tune TV to the same channel number. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owners manual.) 1 N I V A ANT OUT S-VIDEO VIDEO L R ANT IN OUTPUT SWITCH Wall Jack 2 Antenna 32/37/42/47/52LG60, 42LGX P M O C I O D U A COAX OPTIC 1 ANTENNA/

CABLE IN RS-232C IN

(SERVICE ONLY) REMOTE CONTROL IN S-VIDEO VIDEO L R ANT OUT OUTPUT SWITCH ANT IN 2 Wall Jack Antenna E X T E R N A L E Q U I P M E N T S E T U P 33 EXTERNAL EQUIPMENT SETUP Composite (RCA) Connection 1. How to connect 1 Connect the AUDIO/VIDEO jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left

= white, and Audio Right = red) 2. How to use Insert a video tape into the VCR and press PLAY on the VCR.

(Refer to the VCR owners manual.) Select the A V 1 input source on the TV using the INPUT button on the remote control. If connected to AV IN2, select AV2 input source on the TV.

NOTE G If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO jack of the TV. Plasma TV, 32/37/42LG30, 37/42/47/52LG50, 32/42/47/52LG70, 47LG90 ANT IN S-VIDEO VIDEO L R ANT OUT OUTPUT SWITCH 1 ANTENNA/

CABLE IN AUDIO

(RGB/DVI) REMOTE CONTROL IN DIGITAL AUDIO OUT OPTICAL COAXIAL RS-232C IN

(CONTROL & SERVICE) AUDIO OUT L R AUDIO NT IN S-VIDEO VIDEO L

(MONO) AUDIO R 1 N I V A 32/37/42/47/52LG60, 42LGX 1 N I B S U 4 N I I M D H R I O D U A O N O M L

O E D V I AV IN ANT IN S-VIDEO VIDEO L R ANT OUT OUTPUT SWITCH E X T E R N A L E Q U I P M E N T S E T U P 34 S-Video Connection (Except 32/37/42/47/52LG60, 42LGX) 1. How to connect 1 2 Connect the S-VIDEO output of the VCR to the S -VIDEO input on the TV. ANT IN S-VIDEO VIDEO L R Connect the audio outputs of the VCR to the AUDIO input jacks on the TV. ANT OUT OUTPUT SWITCH ANTENNA/

CABLE IN AUDIO

(RGB/DVI) REMOTE CONTROL IN 2 1 DIGITAL AUDIO OUT OPTICAL COAXIAL RS-232C IN

(CONTROL & SERVICE) AUDIO OUT L R AUDIO NT IN S-VIDEO VIDEO L

(MONO) AUDIO R 1 N I V A 2. How to use Insert a video tape into the VCR and press PLAY on the VCR.

(Refer to the VCR owners manual.) Select the A V 1 input source on the TV using the INPUT button on the remote control.

NOTE G S-Video provides better quality than composite. Use it when available. CAUTION G Do not connect to both Video and S-Video at the same time. In the event that you connect both Video and the S-Video cables, only the S-Video will work. E X T E R N A L E Q U I P M E N T S E T U P 35 EXTERNAL EQUIPMENT SETUP OTHER A/V SOURCE SETUP 1. How to connect 1 Connect the AUDIO/VIDEO jacks between TV and external equipment. Match the jack colors.

(Video = yellow, Audio Left = white, and Audio Right = red) 2. How to use Select the A V 2 input source on the TV using the INPUT button on the remote control. If connected to AV IN1 input, select the A V 1 input source on the TV. Operate the corresponding external equipment. Camcorder Video Game Set VIDEO L R 1 N I B S U 3 N I I M D H R I O D U A O N O M L

O E D V I E X T E R N A L E Q U I P M E N T S E T U P 36 PC SETUP This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. VGA (D-Sub 15 pin) Connection Plasma TV, 32/37/42LG30, 37/42/47/52LG50, 32/42/47/52LG70, 47LG90 32/37/42/47/52LG60, 42LGX N 2 1 RGB IN RGB(PC) AUDIO

(RGB/DVI) REMOTE CONTROL IN

(CO Y PB PR L R VIDEO COMPONENT IN AUDIO 1 2 N I T N E N O P M O C O E D V I I O D U A 1 RS-232C IN

(SERVICE ONLY) REMOTE CONTROL IN D

I M D 3 H AUDIO N I B G R

(RGB/DVI) 1 2 DIGITAL AUDIO OUT COAXIAL OPTICAL RGB(PC) ANTENNA/

CABLE IN 2 RGB OUTPUT AUDIO RGB OUTPUT AUDIO 1. How to connect 1 2 Connect the VGA output of the PC to the R G B (P C) jack on the TV. Connect the PC audio output to the AUDIO (RGB/DVI) jack on the TV. 2. How to use Turn on the PC and the TV. Select the RGB-PC input source on the TV using the INPUT button on the remote control. E X T E R N A L E Q U I P M E N T S E T U P 37 EXTERNAL EQUIPMENT SETUP DVI to HDMI Connection 1. How to connect 1 2 32/37/42LG30, 37/42/47/52LG50, Plasma TV

- Connect the DVI output of the PC to the HDMI/DVI IN 1, 2, or 3 jack on the TV. 32/37/42/47/52LG60, 32/42/47/52LG70, 42LGX, 47LG90

- Connect the DVI output of the PC to the HDMI/DVI IN 1, 2, 3, or 4 jack on the TV. Connect the PC audio output to the AUDIO (RGB/DVI) jack on the TV. 2. How to use Turn on the PC and the TV. 32/37/42LG30, 37/42/47/52LG50, Plasma TV

- Select the HDMI1, HDMI2, or HDMI3 input source on the TV using the INPUT button on the remote control. 32/37/42/47/52LG60, 32/42/47/52LG70, 42LGX, 47LG90

- Select the HDMI1, HDMI2, HDMI3, or HDMI4 input source on the TV using the INPUT button on the remote control.

NOTES G 32/37/42LG30, 42/50PG25: To get the the best picture quality, adjust the PC graphics card to 1360x768. G 37/42/47/52LG50, 32/37/42/47/52LG60, 32/42/47/52LG70, 42LGX, 47LG90, 50/60PG60, 50/60PG70: To get the the best picture quality, adjust the PC graphics card to 1920x1080. the resolution, vertical pattern, contrast or bright-

ness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear. G Avoid keeping a fixed image on the screen for a long period of time. The fixed image could become permanently imprinted on the screen. G Depending on the graphics card, DOS mode may G The synchronization input form for Horizontal and not work if a HDMI to DVI Cable is in use. Vertical frequencies is separate. G In PC mode, there may be noise associated with E X T E R N A L E Q U I P M E N T S E T U P 38 32/37/42LG30, 37/42/47/52LG50 Plasma TV, 32/42/47/52LG70, 47LG90 RGB IN RGB(PC) AUDIO

(RGB/DVI) REMOTE CONTROL IN HDMI/DVI IN R

(CONT Y PB PR L R VIDEO COMPONENT IN AUDIO S 3 2 1 RGB IN RGB(PC) AUDIO

(RGB/DVI) REMOTE CONTROL IN Y PB PR 2 1 L R VIDEO COMPONENT IN AUDIO

(CO 1 N I V A 2 1 2 HDMI/DVI IN 2 1 2 1 1 DVI-PC OUTPUT AUDIO DVI-PC OUTPUT AUDIO N I I V D

I M D H N I B G R 32/37/42/47/52LG60, 42LGX 21 1 2 DIGITAL AUDIO OUT COAXIAL 3 AUDIO

(RGB/DVI) OPTICAL RGB(PC) ANTENNA/

CABLE IN N I T N E N O P M O C O E D V I I O D U A 1 RS-232C IN 2

(SERVICE ONLY) REMOTE CONTROL IN DVI-PC OUTPUT AUDIO E X T E R N A L E Q U I P M E N T S E T U P 39 EXTERNAL EQUIPMENT SETUP Supported Display Specifications (RGB-PC, HDMI-PC)

NOTE G Depending on the graphics card, some resolution settings may not allow the image to be positioned on the screen properly. G If there are overscan in HDMI-PC 1920x1080, change aspect ratio to Just scan. For 32/37/42LG30 For 37/42/47/52LG50, 32/37/42/47/52LG60, 32/42/47/52LG70, 42LGX, 47LG90 Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) 640x350 31.468 640x350 31.469 720x400 640x480 800x600 1024x768 1280x768 1360x768 1366x768 31.469 31.469 37.879 48.363 47.776 47.720 47.130 70.08 70.08 59.94 60.31 60.00 59.87 59.799 59.65

* Only RGB-PC mode 70.09 70.08 59.94 75.00 72.80 56.25 60.31 75.00 72.18 60.00 70.06 75.02 59.87 74.893 60.02 75.025 60.015 60.00 31.469 31.469 37.500 37.861 35.156 37.879 46.875 48.077 48.363 56.476 60.023 47.776 60.289 63.981 79.976 47.712 75.00 720x400 640x480 800x600 1024x768 1280x768 1280x1024 1360x768 1600x1200 1920x1080 RGB-PC 1920x1080 HDMI-PC 66.587 59.934 67.5 60.00

* Only RGB-PC mode E X T E R N A L E Q U I P M E N T S E T U P 40 For 42/50PG25, 50/60PG60, 50/60PG70 Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) 640x350 31.468 720x400 640x480 800x600 1024x768 1280x768 1280x1024 1360x768 1600x1200 31.469 31.469 37.500 37.861 35.156 37.879 46.875 48.077 48.363 56.476 60.023 47.776 60.289 63.981 79.976 47.712 75.00 70.09 70.08 59.94 75.00 72.80 56.25 60.31 75.00 72.18 60.00 70.06 75.02 59.87 74.893 60.02 75.025 60.015 60.00 1920x1080 66.587 59.934

* Only RGB-PC mode E X T E R N A L E Q U I P M E N T S E T U P 41 EXTERNAL EQUIPMENT SETUP Screen Setup for PC mode Selecting Resolution You can choose the resolution in RGB-PC mode. The Position, Phase, and Size can also be adjusted. PICTURE Move Enter SCREEN Move MENU Prev. E 50 60 60 0 Brightness Sharpness Color Tint Advanced Control Reset R G Screen (RGB-PC) TruMotion Demo 1024 x 768 1280 x 768 1360 x 768 1366 x 768 Resolution G Auto config. Position Size Phase Reset Only for 32/37/42LG30 Select PICTURE. Select Screen (RGB-PC). Select Resolution. Select the desired resolution. 1 MENU 2 3 4 5 ENTER ENTER ENTER ENTER E X T E R N A L E Q U I P M E N T S E T U P 42 Auto Configure Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still not correct, try using the manual settings or a different resolution or refresh rate on the PC. PICTURE Move Enter SCREEN Move MENU Prev. E 50 60 60 0 Brightness Sharpness Color Tint Advanced Control Reset R G Screen (RGB-PC) TruMotion Demo Resolution Auto config. G Position Size Phase Reset To Set Yes No 1 MENU Select PICTURE. 2 3 4 5 ENTER Select Screen (RGB-PC). ENTER Select Auto config.. ENTER Select Y e s. ENTER Start Auto Configuration. If the position of the image is still not correct, try Auto adjustment again. If picture needs to be adjusted again after Auto adjustment in RGB-PC, you can adjust the P o s i t i o n, S i z e or Phase. E X T E R N A L E Q U I P M E N T S E T U P 43 EXTERNAL EQUIPMENT SETUP Adjustment for screen Position, Size, and Phase If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture phase manually. This feature operates only in RGB-PC mode. PICTURE Move Enter E 50 60 60 0 Brightness Sharpness Color Tint Advanced Control Reset R G Screen (RGB-PC) TruMotion Demo SCREEN Move MENU Prev. Resolution Auto config. Position G Size Phase Reset F D E G 1 MENU Select PICTURE. 2 3 4 5 ENTER ENTER Select Screen (RGB-PC). Select Position, S i z e, or Phase. ENTER Make appropriate adjustments. ENTER Position: This function is to adjust pic-

ture to left/right and up/down as you prefer. S i z e: This function is to minimize any vertical bars or stripes visible on the screen background. And the horizontal screen size will also change. P h a s e: This function allows you to remove any horizontal noise and clear or sharpen the image of characters. E X T E R N A L E Q U I P M E N T S E T U P 44 Screen Reset (Reset to original factory values) Returns Position, S i z e, and Phase to the default factory settings. This feature operates only in RGB-PC mode. PICTURE Move Enter E 50 60 60 0 Brightness Sharpness Color Tint Advanced Control Reset R G Screen (RGB-PC) TruMotion Demo SCREEN Move MENU Prev. Resolution Auto config. Position Size Phase Reset G To Set Yes No 1 MENU Select PICTURE. 2 3 4 5 ENTER ENTER Select Screen (RGB-PC). Select Reset. ENTER Select Y e s. ENTER E X T E R N A L E Q U I P M E N T S E T U P 45 EXTERNAL EQUIPMENT SETUP USB CONNECTION (Except 32/37/42LG30) i.e) or 1 N I B S U 3 N I I M D H R I O D U A O N O M L

O E D V I AV IN 2 1. How to connect 1 Connect the USB device to the USB I N jack on the side of TV. 2. How to use After connecting the USB I N jack, you use the USB func-

tion. (G p.64) E X T E R N A L E Q U I P M E N T S E T U P 46 AUDIO OUT CONNECTION Send the TVs audio to external audio equipment via the Audio Output port. Analog (Except 32/37/42/47/52LG60, 42LGX) 1. How to connect 1 2 Connect audio outputs to the TVs AUDIO OUT jacks. Set the TV Speaker option - Off in the AUDIO menu.

(G p.93). See the external audio equipment instruction manual for operation. Digital 1. How to connect RS-232C IN

(CONTROL & SERVICE) AUDIO OUT R UDIO S-VIDEO VIDEO L

(MONO) AUDIO R 1 N I V A 1 L R AUDIO 1 2 3 Connect one end of the optical or coaxial cable to the TVs OPTICAL or COAXIAL (Except 32/37/42LG30) port of DIGITAL AUDIO OUT. Connect the other end of the optical or coaxial cable to the digital audio input on the audio equipment. ANTENNA/

CABLE IN UDIO B/DVI) REMOTE CONTROL IN DIGITAL AUDIO OUT OPTICAL COAXIAL Set the TV Speaker option - Off in the AUDIO menu. (G p.93). See the external audio equipment instruction manu-

al for operation. RS-232C IN 1

(CONTROL & SERVICE) AUDIO OUT L R AUDIO N S-VIDEO VIDEO L

(MONO) AUDIO R 1 N I V A 2

NOTE G When connecting with external audio equipments, such as amplifiers or speakers, you can turn the TV speakers off in the menu. (G p . 9 3) CAUTION G Do not look into the optical output port. Looking at the laser beam may damage your vision. G Block the SPDIF out (optical/coaxial) about the contents with ACP(Audio Copy Protection) function. E X T E R N A L E Q U I P M E N T S E T U P 47 WATCHING TV / CHANNEL CONTROL REMOTE CONTROL FUNCTIONS When using the remote control, aim it at the remote control sensor on the TV. TV/STB/DVD/VCR Select the remote operating mode: TV, STB, DVD, or VCR. POWER Turns your TV or any other programmed equipment on or off, depending on the mode. Q.MENU Select the desired quick menu source. G p.51 TV POWER DVD STB Q. MENU MENU VCR INPUT MENU Displays the main menu. Clear all on-screen displays and return to TV viewing from any menu. ENTER INPUT External input modes rotate in regular sequence. VOLUME UP

/DOWN Increase/decrease the sound level. FAV Scroll through the programmed Favorite channels. G p.51 MUTE Switch the sound on or off. G p.50 CHANNEL UP/DOWN PAGE UP/DOWN NUMBER button

(DASH) Select available channels. Move from one full set of screen information to the next one. Used to enter a program number for multiple program channels such as 2-1, 2-2, etc. FLASHBK Tune to the last channel viewed. RETURN AV MODE VOL 1 4 7 FAV MUTE 2 5 8 0 CH P A G E 3 6 9 FLASHBK VCR/DVD, USB, SIMPLINK Control buttons Control video cassette recorders or DVD players. Control USB menu (PHOTO LIST and MUSIC LIST.) Control the SIMPLINK compatible devices. W A T C H I N G T V

C H A N N E L C O N T R O L 48 THUMBSTICK

(Up/Down/Left Right/ENTER) Navigate the on-screen menus and adjust the system settings to your preference. RETURN Allows the user to move return one step in an interactive application or other user interaction function. SIMPLINK See a list of AV devices connected to TV. When you toggle this button, the SIMPLINK menu appears at the screen. G p.62-63 AV MODE It helps you select and set images and sounds. G p.61 Installing Batteries Open the battery compartment cover on the back side and install the batteries matching correct polarity (+with +,-with -). Install two 1.5V AAA batteries. Dont mix old or used batteries with new ones. Close cover. W A T C H I N G T V

C H A N N E L C O N T R O L 49 WATCHING TV / CHANNEL CONTROL TURNING ON THE TV First, connect power cord correctly. At this moment, the TV switches to standby mode. In standby mode to turn TV on, press the button on the TV or press the POWER, INPUT, CH(

(0~9) button on the remote control. or

, INPUT, CH (DE or

), Number Select the viewing source by using the INPUT button on the remote control. This TV is programmed to remember which power state it was last set to, even if the power cord is out. When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode.

NOTE G If you intend to be away on vacation, disconnect the power plug from the wall power outlet. 1 2 3 W A T C H I N G T V

C H A N N E L C O N T R O L CHANNEL SELECTION 1 Press the CH (

or

) or NUMBER buttons to select a channel number. VOLUME ADJUSTMENT Adjust the volume to suit your personal preference. Press the VOL (+ or -) button to adjust the volume. If you want to switch the sound off, press the MUTE button. You can cancel the Mute function by pressing the MUTE or VOL (+ or -) button. 1 2 3 50

 

 

QUICK MENU Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual. Q.Menu (Quick Menu) is a menu of features which users might use frequently. I AAssppeecctt RRaattiioo: Selects your desired picture format. I PPoowweerr SSaavviinngg (Plasma TV Only): Adjusts screen brightness to reduce the power consumption of the TV. I BBaacckklliigghhtt (LCD TV Only): Adjust the brightness of LCD panel to control the brightness of the screen. I CClleeaarr VVooiiccee: By differentiating the human sound range from others, it helps make human voices sound better. I PPiiccttuurree MMooddee: Selects the factory preset picture depend on the viewing environment. I SSoouunndd MMooddee: Selects the factory preset sound for type of program. I CCaappttiioonn: Select on or off. I MMuullttii AAuuddiioo: Changes the audio language (Digital signal). SSAAPP: Selects MTS sound (Analog signal). I SSlleeeepp TTiimmeerr: Select the amount of time before your TV turns off automatically. I DDeell//AAdddd//FFaavv: Select channel you want to add/delete or add the channel to the Favorite List. I UUSSBB EEjjeecctt: Select USB Eject in order to eject USB device. Plasma TV Q.Menu LCD TV Q.Menu Aspect Ratio FF 16:9 GG Aspect Ratio FF 16:9 GG Power Saving Clear Voice Picture Mode Sound Mode Caption Multi Audio Sleep Timer Del/Add/Fav USB Eject CH 3 Off Vivid Standard Off English Off Add Eject Backlight Clear Voice Picture Mode Sound Mode Caption Multi Audio Sleep Timer Del/Add/Fav USB Eject CH 3 Off Vivid Standard Off English Off Add Eject Close Close Except 32/37/42LG30 1Q. MENU 2 3Q. MENU Display each menu. Make appropriate adjustments. Return to TV viewing. W A T C H I N G T V

C H A N N E L C O N T R O L 51 WATCHING TV / CHANNEL CONTROL INITIAL SETTING This Function guides the user to easily set the essential items for viewing the TV for the first time when pur-

chasing the TV. If will be displayed on the screen when turning the TV on for the first time. It can also be acti-

vated from the user menus. I Default selection is HH oo mm ee. We recommend setting the TV to HH oo mm ee mode for the best picture in your home environment. I IInn--ssttoorree Mode is only intended for use in retail environments. Customers can adjust the PPiiccttuurree menu -

PPiiccttuurree mmooddee manually while inspecting the TV, but the TV will automatically return to preset in-store mode after 5 minutes. Step1. Mode setting Step1. Mode Setting

Selecting the environment. Choose the setting mode you want. In Store Home Enter RETURN Exit Step2. Time setting Step2. Time Setting Current Time Setting FF Auto GG Year Month Date Hour Minute Time Zone Daylight Saving 2007 11 15 5 PM 52 Eastern Off Enter RETURN Exit Select HH oo mm ee Mode. Select AAuuttoo or MMaannuuaall. Select desired time option. 1 2 ENTER 1 2 3 ENTER W A T C H I N G T V

C H A N N E L C O N T R O L 52 Step3. Option setting Step3. Option Setting 1. OSD Language Setting FF English GG 2. Audio Language Setting French Enter RETURN Exit Step4. Auto Tuning Step4. Auto Tuning Auto Tuning can change channel map. Do you want to start Auto Tuning?

Enter Enter RETURN Exit Select OOSSDD LLaanngguuaaggee SSeettttiinngg or AAuuddiioo LLaanngguuaaggee SSeettttiinngg. Select your desired language. 1 2 3 ENTER 1 ENTER Start AAuuttoo TTuunniinngg.

NOTE I You can also adjust IInniittiiaall SSeettttiinngg in the OOPPTTIIOONN menu. W A T C H I N G T V

C H A N N E L C O N T R O L 53 WATCHING TV / CHANNEL CONTROL ON-SCREEN MENUS SELECTION Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual. All models (Except 32/37/42LG30) CHANNEL Move Enter PICTURE Move Enter Auto Tuning Manual Tuning Channel Edit Aspect Ratio : 16:9 Picture Mode : Standard Backlight Contrast Brightness Sharpness Color Tint E 80 90 50 60 60 0 R G OPTION Move Enter Language Input Label SIMPLINK Key Lock Caption ISM Method Power Saving Set ID E

: English

: On

: Off

: Off

: Normal

: Level 0

: 1 CHANNEL PICTURE AUDIO TIME OPTION LOCK INPUT USB AUDIO Auto Volume Clear Voice Balance Sound Mode

: Off

: On Move Enter 0 L R

: Standard SRS TruSurround XT: Off Treble Bass Reset E 50 50 TIME Move Enter

: Feb/21/2008 2:10 AM Clock

: Off Off Time On Time

: Off Sleep Timer : Off Auto Sleep : Off LOCK Move Enter INPUT Move Enter USB Move Enter Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block Lock System : Off Set Password Block Channel TV Rating-English TV Rating-French Downloadable Rating Input Block For USA For Canada Antenna Cable AV1 AV2 Component1 Component2 RGB-PC HDMI1 E PHOTO LIST MUSIC LIST 1 MENU Display each menu. 2 3 ENTER Select a menu item. ENTER Enter to the pop up menu. 4 MENU Return to TV viewing.

NOTE GG IISSMM MMeetthhoodd, PPoowweerr SSaavviinngg: Only PPllaassmmaa TTVV. GG BBaacckklliigghhtt,, PPoowweerr IInnddiiccaattoorr,, TTrruuMMoottiioonn DDeemmoo: Only LLCCDD TTVV.

(But, TT rr uu MM oo tt ii oo nn DD ee mm oo: Only for 3322//3377//4422//4477//5522LLGG6600,, 3322//4422//4477//5522LLGG7700,, 4422LLGGXX,, 4477LLGG9900) GG SSeett IIDD: Except 3322//3377//4422//4477//5522LLGG6600,, 4422LLGGXX. W A T C H I N G T V

C H A N N E L C O N T R O L 54 Only for 32/37/42LG30 CHANNEL Move Enter PICTURE Move Enter AUDIO Auto Volume Clear Voice Balance Sound Mode

: Off

: On Move Enter 0 L R

: Standard SRS TruSurround XT: Off Treble Bass Reset E 50 50 Aspect Ratio : 16:9 Picture Mode : Standard Backlight Contrast Brightness Sharpness Color Tint E 80 90 50 60 60 0 R G CHANNEL PICTURE AUDIO TIME OPTION LOCK LOCK Move Enter Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block Lock System : Off Set Password Block Channel TV Rating-English TV Rating-French Downloadable Rating Input Block For USA For Canada Auto Tuning Manual Tuning Channel Edit TIME Move Enter

: Feb/21/2008 2:10 AM Clock

: Off Off Time On Time

: Off Sleep Timer : Off Auto Sleep : Off OPTION Language Input Label SIMPLINK Key Lock Caption Set ID Power Indicator Initial Setting Move Enter

: English

: On

: Off

: Off

: 1

: Home 1 MENU Display each menu. 2 3 ENTER Select a menu item. ENTER Enter to the pop up menu. 4 MENU Return to TV viewing. W A T C H I N G T V

C H A N N E L C O N T R O L 55 WATCHING TV / CHANNEL CONTROL CHANNEL SETUP Auto Scan (Auto Tuning) Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list. Run Auto Tuning again after any Antenna/Cable connection changes. Move Enter CHANNEL Auto Tuning Manual Tuning Channel Edit Move Enter CHANNEL Auto Tuning Manual Tuning Channel Edit Press Yes button to begin auto tuning. Yes No 1 MENU Select CCHHAANNNNEELL. 2 3 4 ENTER ENTER Select AAuuttoo TTuunniinngg. Select YY ee ss. ENTER Run AAuuttoo ttuunniinngg. 5RETURN MENU Return to the previous menu. Return to TV viewing. I A password is required to gain access to Auto Tuning menu if the Lock System is turned on. W A T C H I N G T V

C H A N N E L C O N T R O L 56 Add/Delete Channel (Manual Tuning) If selecting DTV or CADTV input signal, you can view the on-screen signal strength monitor to see the quality of the signal being received. Move Enter CHANNEL Auto Tuning Manual Tuning Channel Edit CHANNEL Auto Tuning Manual Tuning Channel Edit Move Enter FF DTV GG Select channel type and RF-channel number. Channel DTV 2-1 2 Bad Normal Good Delete Close 1 MENU ENTER ENTER 2 3 4 5 6RETURN MENU Select CCHHAANNNNEELL. Select MMaannuuaall TTuunniinngg. Select DD TT VV, TT VV, CCAADDTTVV, or CC AA TT VV. Select channel you want to add or delete. ENTER Select AA dd dd or DDeelleettee. Return to the previous menu. Return to TV viewing. I A password is required to gain access to Manual Tuning menu if the Lock System is turned on. W A T C H I N G T V

C H A N N E L C O N T R O L 57 WATCHING TV / CHANNEL CONTROL CHANNEL SETUP Channel Editing A custom list can be created by toggling each channel on or off with ENTER button. The channels in the Custom List are displayed in black and the channels deleted from the Custom List are displayed in gray. Once a channel is highlighted you can add or delete the channel by referring to the small window at the top-

right corner of the screen. Add/Delete Move CH Move Page MENU Previous RETURN Exit W A T C H I N G T V

C H A N N E L C O N T R O L 58 Move Enter CHANNEL Auto Tuning Manual Tuning Channel Edit 1 MENU Select CCHHAANNNNEELL. 2 3 4 ENTER Select CChhaannnneell EEddiitt. ENTER ENTER Select a channel. Select channel you want to add or delete. 5 MENU Return to the previous menu. RETURN Return to TV viewing. INPUT LIST Only these input signals which are connected to a TV can be activated and selected. Antenna Cable AV1 AV2 Component1 1 INPUT ENTER Select the desired input source. I You can also select the desired input source in the IINNPPUUTT menu

(Except 32/37/42LG30). 32/37/42LG30, 37/42/47/52LG50 Antenna Cable AV1 AV2 Component1 Component2 HDMI3 HDMI2 HDMI1 RGB-PC Plasma TV, 32/42/47/52LG70, 47LG90 Antenna Cable AV1 AV2 Component1 Component2 HDMI4 HDMI3 HDMI2 HDMI1 RGB-PC 32/37/42/47/52LG60, 42LGX Antenna Cable AV Component1 Component2 HDMI4 HDMI3 HDMI2 HDMI1 RGB-PC ie) Disconnected inputs are inactive (grayed out) Antenna Cable AV1 AV2 Component1 Q.MENU Input Label RETURN Exit Select a desired input source (except AAnntteennnnaa or CCaabbllee). Then, you can select your desired Input Label with using Q. MENU button. GG pp..6600 I AAnntteennnnaa: Select it to watch over-the-air broadcasts. I CCaabbllee: Select it to watch cable and digital cable. I AA VV: Select them to watch a VCR or other external equipment. I CCoommppoonneenntt: Select them to watch DVD or a Digital set-top box. I RRGGBB--PPCC: Select it to view PC input. I HH DD MM II: Select them to watch high definition devices. W A T C H I N G T V

C H A N N E L C O N T R O L 59 WATCHING TV / CHANNEL CONTROL INPUT LABEL You can set a label for each input source when it's not in use. FF GG OPTION Language Input Label SIMPLINK Key Lock Caption ISM Method Power Saving Set ID Move Enter

: English

: On

: Off

: Off

: Normal

: Level 0

: 1 EE AV1 AV2 Component1 Component2 RGB-PC HDMI1 HDMI2 HDMI3 FF GG AV1 AV2 Component1 Component2 RGB-PC HDMI1 HDMI2 HDMI3 HDMI4 Close 32/37/42LG30, 37/42/47/52LG50 Close Plasma TV, 32/42/47/52LG70, 47LG90 FF GG AV Component1 Component2 RGB-PC HDMI1 HDMI2 HDMI3 HDMI4 Close 32/37/42/47/52LG60, 42LGX With using OPTION menu With using INPUT button 1 MENU ENTER ENTER 2 3 4 5RETURN MENU Select OOPPTTIIOONN. Select IInnppuutt LLaabbeell. Select the source. Select the source. Select the label. Return to the previous menu. 1 INPUT 2Q. MENU 3RETURN MENU Select the label. Return to TV viewing. Return to the previous menu. Return to TV viewing. I When new external device is connected, this popup menu is displayed automatically. If selecting YY ee ss, you can select input source that you want to appreciate. I But, when selecting SSIIMMPPLLIINNKK - OO nn, popup menu for HDMI input will not be displayed.

New external device is connected. Do you want to enjoy this?

Yes No

Select input source that you want to appreciate. AV1 AV2 Component1 W A T C H I N G T V

C H A N N E L C O N T R O L 60 AV MODE You can select the optimal images and sounds. All models (Except 50/60PG60, 50/60PG70) Off Cinema Game Sport Only for 50/60PG60, 50/60PG70 Off Cinema Game Sport Press the AAVV MMOODDEE button repeatedly to select the desired source. 1AV MODE 2 ENTER I If you select CCiinneemmaa //

CCiinneemmaa in AV mode, CCiinneemmaa will be selected both for PICTURE menu - Picture Mode and AUDIO menu - Sound Mode respectively. I If you select OO ff ff in AV mode, the PPiiccttuurree MMooddee and SSoouunndd MMooddee return to previous selected value. W A T C H I N G T V

C H A N N E L C O N T R O L 61 WATCHING TV / CHANNEL CONTROL This function operates only with devices with the The TV might not function properly when using it with other products with HDMI-CEC function. This allows you to control and play other AV devices connected with HDMI cable without additional cables and settings. To start using SIMPLINK, turn it on in the user menus. logo. OPTION Language Input Label SIMPLINK Key Lock Caption ISM Method Power Saving Set ID E Move Enter

: English

: On

: Off

: Off

: Normal

: Level 0

: 1 OPTION Language Input Label SIMPLINK Key Lock Caption ISM Method Power Saving Set ID Move Enter

: English Off On

: On

: Off

: Off

: Normal

: Level 0

: 1 E 1 MENU 2 3 ENTER ENTER 4RETURN MENU Select OOPPTTIIOONN. Select SSIIMMPPLLIINNKK. Select OO nn or OO ff ff. Return to the previous menu. Return to TV viewing.

NOTE GG Connect the HDMI/DVI IN or HDMI IN terminal of the TV to the rear terminal (HDMI terminal) of the SIMPLINK device with the HDMI cable. GG When you switch the Input source with the INPUT button on the remote control, the SIMPLINK device will stop. GG When you select a device with home theater functionality, the sound output automatically switches to the home theater speakers. GG If a connected SIMPLINK home theater system doesn't play the audio from the TV, connect the DIGITAL AUDIO OUT terminal on the back of the TV to the DIGITAL AUDIO IN terminal on the back of the SIM-

PLINK device with an OPTICAL cable. W A T C H I N G T V

C H A N N E L C O N T R O L 62 SIMPLINK Functions I DDiirreecctt PPllaayy:: After connecting AV devices to the TV, you can directly control the devices and play media with-

out additional settings. I SSeelleecctt AAVV ddeevviiccee:: Enables you to select one of the AV devices connected to TV. I DDiisscc ppllaayybbaacckk:: Control connected AV devices by pressing the I PPoowweerr ooffff aallll ddeevviicceess:: When you power off the TV, all connected devices are turned off. I SSwwiittcchh aauuddiioo--oouutt:: Offers an easy way to switch audio-out. I SSyynncc PPoowweerr oonn:: When you play the connected AV device, TV will automatically turn on.

(A device, which is connected to the TV through a HDMI cable but does not support SIMPLINK, does not provide this function) Note: To operate SIMPLINK, an HDMI cable over Version 1.2 with *CEC function should be used. (*CEC: Consumer Electronics Control).

, ENTER, G, A, ll ll, FF and GG buttons. 1 2 3 TV Display SSIIMMPPLLIINNKK menu. ENTER Select the desired device. ENTER Control connected AV devices. SIMPLINK Menu 1 2 3 4 5 TTVV vviieewwiinngg: Switch to the previous TV channel regardless of the current mode. DDIISSCC ppllaayybbaacckk: Select and play discs. When multiple discs are available, the titles of discs are conveniently displayed at the bottom of the screen. VVCCRR ppllaayybbaacckk: Control the connected VCR. HHDDDD RReeccoorrddiinnggss ppllaayybbaacckk: Control recordings stored in HDD. AAuuddiioo OOuutt ttoo HHoommee TThheeaatteerr ssppeeaakk--

eerr//AAuuddiioo OOuutt ttoo TTVV: Select Home Theater speaker or TV speaker for Audio Out. 1 2 3 4 5 GG When no device is connected

(displayed in gray) GG Selected Device GG When a device is connected

(displayed in bright color) W A T C H I N G T V

C H A N N E L C O N T R O L 63 USB

* Except 32/37/45LG30 ENTRY MODES When you connect a USB device, this screen is displayed automatically. In USB device, you can not add a new folder or delete the existing folder. 1 Connect the USB device to the UUSSBB IINN jacks on the side of TV. N I B S U 3 N I I M 2 Select PPHHOOTTOO LLIISSTT or MMUUSSIICC LL II SS TT PHOTO LIST MUSIC LIST 3 ENTER I It doesnt support USB HDD I This TV supports JPG and MP3. When removing the USB device Select the UUSSBB EEjjeecctt menu before removing the USB device. Select UUSSBB EEjjeecctt. 1Q. MENU 2 ENTER Precautions when using the USB device GG Only a USB storage device is recognizable. GG If the USB storage device is connected through a USB hub, the device is not recognizable. GG A USB storage device using an automatic recogni-

tion program may not be recognized. GG A USB storage device which uses its own driver may not be recognized. GG In case of a card reader, up to four memory cards are concurrently recognizable. GG The recognition speed of a USB storage device may depend on each device. GG Please do not turn off the TV or unplug the USB device when the connected USB storage device is working. When such device is suddenly separated or unplugged, the stored files or the USB storage device may be damaged. GG Please do not connect the USB storage device which was artificially maneuvered on the PC. The device may cause the product to malfunction or fail to be played. Never forget to use only a USB storage device which has normal music files or image files. GG Please use only a USB storage device which was formatted as a FAT or NTFS file system provided with the Windows operating system. In case of a storage device formatted as a different utility pro-

gram which is not supported by Windows, it may not be recognized. GG Please connect power to a USB storage device which requires an external power supply. If not, the device may not be recognized. GG Please connect a USB storage device with cable is offered by USB maker. If connected with cable is not offered by USB maker or an excessively long cable, the device may not be recognized. GG Some USB storage devices may not be supported or operated smoothly. GG File alignment method of USB storage device is similar to Window XP and filename can recognize up to 100 English characters. GG Please backup important files because data on USB device may be damaged. Data management is consumer's responsibility and as a result, the man-

ufacturer does not cover data damage. U S B 64 PHOTO LIST You can view .JPG files from USB storage devices. The On Screen Display on your model may be slightly different. Supported photo file: *.JPG I You can play JPG files only. I Only baseline scan is supported among JPG. Screen Components 1 MENU 2 Select UU SS BB. ENTER ENTER Select PPHHOOTTOO LLIISSTT. Moves to upper level file Preview: Display the thumbnail/folder name of the photo in the selected folder Current page/Total pages 2 PHOTO LIST TOP FOLDER Drive1 3 4 Page 1/1 No Marked Drive1 1 Total number of marked photos 2Folders, 4Files 5 USB Device Free Space 150MB Usable USB memory Corresponding buttons on the remote control 1 Upper Navigate PopUp Menu CH Move Page FAV Mark RETURN Exit 6 1 2 3 4 5 6 U S B 65 USB Photo Selection and Popup Menu PHOTO LIST TOP FOLDER Drive1 Page 1/1 No Marked Drive1 USB Device Free Space 150MB U S B 2Folders, 4Files Upper Navigate PopUp Menu CH Move Page FAV Mark RETURN Exit PHOTO LIST Drive1 Butterfly Page 1/1 No Marked Upper Photo X.Box 1366x768 125KB Upper USB Device Free Space 150MB 1366x768 125KB View Mark All Delete Cancel Navigate PopUp Menu CH Move Page FAV Mark RETURN Exit When you select a file (not folder), this PopUp menu is displayed. GG VViieeww: Display the selected item. GG MMaarrkk AAllll: Mark all photos on the screen. GG UUnnmmaarrkk AAllll: Deselect all marked photos. GG DDeelleettee: Delete the selected photo item. GG CCaanncceell: Close the pop-up menu. 1 2 3 4 ENTER ENTER Select the target folder or drive. Select the desired photos. Show the Popup menu. ENTER Select the desired Popup menu. I Use the CC HH photo page. button to navigation in the I Use the FFAAVV button to mark or unmark a photo. When one or more photos are marked, you can view individual photos or a slide show of the marked photos. If no photos are marked, you can view all photos individually or all pho-

tos in the folder in a slide show. 66 Full Screen Menu You can change the Photo List view so that it fills the screen. More operations are available in full screen mode. PHOTO LIST TOP FOLDER Drive1 Page 1/1 No Marked Drive1 USB Device Free Space 150MB 2Folders, 4Files Upper Navigate PopUp Menu CH Move Page FAV Mark RETURN Exit PHOTO LIST Drive1 Butterfly Page 1/1 No Marked Upper Photo X.Box 1366x768 125KB Upper USB Device Free Space 150MB 1366x768 125KB View Mark All Delete Cancel Navigate PopUp Menu CH Move Page FAV Mark RETURN Exit ENTER ENTER Select the target folder or drive. Select the desired photos. Show the Popup menu. Select VV ii ee ww. 1/17 Sideshow BGM Delete Option Hide The aspect ratio of a photo may change the size of the photo displayed on the screen in full size. ENTER The selected photo is displayed in full size. I Use the CC HH photo page. button to navigation in the 1 2 3 4 5 U S B 67 USB U S B 68 6 ENTER Select the SSiiddeesshhooww, BBGGMM, DDeelleettee, OOppttiioonn, or HHiiddee..

((RRoottaattee)), 1/17 Sideshow BGM Delete Option Hide I Use button to select the previous or next photo. I Use button to select and control the menu on the full-sized screen. GG SSiiddeesshhooww: Selected photos are displayed during the slide show. If no photo is selected, all photos in the cur-

rent folder are displayed during slide show. I Set the time interval of the slide show in OOppttiioonn. I A slide show continues for a maximum of 4 hours. After 4 hours, the slide show will end and go to TV mode or external input mode. GG BB GG MM: Listen to music while viewing photos in full size. I Set the BGM device and album in OOppttiioonn. GG

((RRoottaattee)): Rotate photos. I Rotates the photo 90, 180, 270, 360 clockwise. GG DDeelleettee: Delete photos. GG OOppttiioonn: Set values for SSlliiddee SSppeeeedd and MMuussiicc Press FF GG to set the time interval between slides. Slide Speed Music Folder Fast

... ENTER Cancel FFoollddeerr. I Use Then go to tings. button and EENNTTEERR button to set values. and press EENNTTEERR to save the set-

I You cannot change MMuussiicc FFoollddeerr while BGM is playing. GG HHiiddee : Hide the menu on the full-sized screen. I To see the menu again on the full-sized screen, press EENNTTEERR button to display. NOTE

GG This TV will not be able to decode most JPEG images saved using the Progressive option. MUSIC LIST You can use the Music List menu to play MP3 files form a USB storage device. This TV cannot play back copy-protected files. The On Screen Display on your model may be slightly different. Supported music file: *.MP3 Bit rate range 40Kbps ~ 320Kbps Sampling rate (Sampling Frequency) MPEG1 : 32000, 44100, 48000Hz MPEG2 : 16000, 24000, 22050Hz MPEG2.5 : 16 ~ 48KHz Screen Components 1 MENU 2 Select UU SS BB. ENTER ENTER Select MMUUSSIICC LLIISSTT. 1 2 3 4 5 6 Moves to upper level file Preview: If any album jacket for the file exists, this jack-

et is displayed. Current page/Total pages Total number of marked musics Usable USB memory Corresponding buttons on the remote control 2 1 3 4 Page 1/1 No Marked Title Upper Arirang Good Bye MUSIC LIST Drive1 Arirang 3945 KB, 128 Kbps Upper 5 USB Device Free Space 150MB Play Time 04:12 05:30 Navigate PopUp Menu CH Move Page FAV Mark RETURN Exit 6 U S B 69 USB Music Selection and Popup Menu Up to 6 music titles are listed per page. MUSIC LIST Drive1 Arirang Page 1/1 No Marked USB Device Free Space 150MB Title Play Time Upper Arirang Good Bye 04:12 05:30 3945 KB, 128 Kbps Upper Navigate PopUp Menu CH Move Page FAV Mark RETURN Exit MUSIC LIST Drive1 Arirang 3945 KB, 128 Kbps Upper Page 1/1 No Marked USB Device Free Space 150MB Title Play Time Upper Arirang Good Bye 3945 KB 128 Kbps Play Play with Photo Mark All Delete Cancel Navigate PopUp Menu CH Move Page FAV Mark RETURN Exit 1 2 3 4 ENTER ENTER Select the target folder or drive. Select the desired musics. Show the Popup menu. ENTER Select the desired Popup menu. 5RETURN Return to TV viewing U S B 70 GG PPllaayy (During stop): Play the selected music. Once a song finishes playing, the next selected one will be played. When there are no selected musics to play, the next one in the current fold-

er will be played. If you go to a different folder and press the EENNTTEERR button, the current music in playback will stop. GG PPllaayy MMaarrkkeedd: Play the selected musics. Once a music finishes playing, the next selected one will be played automatically. GG SSttoopp PPllaayy (During playback): Stop the play-

ing musics. GG PPllaayy wwiitthh PPhhoottoo: Start playing the selected musics and then move to the Photo List. GG MMaarrkk AAllll: Mark all musics in the folder. GG UUnnmmaarrkk AAllll: Deselect all marked music. GG DDeelleettee: Delete the selected music. GG CCaanncceell: Close the pop-up menu. I Use the CC HH the music page. button to navigation in I Use FF AA VV button to mark or unmark a music file. If no music is marked, all the music in the folder will be played in sequence. When one or more music files are marked, the marked music files will be played in sequence. If you want to listen to only one song repeatedly, just mark that one file and play. I The play information box (as shown below) will automatically move across the screen when there is no user input to pre-

vent a fixed image remaining on the screen for a extended period of time.

NOTE is displayed in front of the music play time. GG When music is playing, GG A damaged or corrupted music file that does not play displays 00:00 as the play time. GG Music files with copy-protection will not play. GG Press EENNTTEERR, AA , or RREETTUURRNN button to stop the screen saver. GG This TV can not play music files less than 16 Kbytes. U S B 71 PICTURE CONTROL PICTURE SIZE (ASPECT RATIO) CONTROL This feature lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV. I RGB-PC input source use 4:3 or 16:9 aspect ratio.

NOTE GG If a fixed image is displayed on the screen for a long time, the image could become imprinted on the screen and remain visible. This phenomenon is common to all manufacturers and is not covered by warranty. Although, after watch-

ing video that did not fill the screen, any after-image from the black bars will normally dissipate after a few minutes. PICTURE Move Enter PICTURE Move Enter Aspect Ratio : 16:9 Picture Mode : Standard Aspect Ratio : 16:9 Picture Mode : Standard Backlight Contrast Brightness Sharpness Color Tint E 80 90 50 60 60 0 R Set By Program 4:3 16:9 Zoom1 Zoom2 Just Scan G I You can also adjust AAssppeecctt RRaattiioo in the QQ--MMeennuu. Backlight Contrast Brightness Sharpness Color Tint E 80 90 50 60 60 0 R G Select PPIICCTTUURREE. Select AAssppeecctt RRaattiioo. Select the desired picture format. Return to the previous menu. Return to TV viewing. 1 MENU 2 3 ENTER ENTER 4RETURN MENU P I C T U R E C O N T R O L 72 Set by program Selects the proper picture proportion to match the sources image.

(4:3 4:3) Zoom 1 Choose Zoom 1 when you want to view the pic-

ture without any alteration. However, the top and bottom portions of the picture will be cropped.

(16:9 16:9) Zoom 2 Choose Zoom 2 when you want the picture to be altered, both vertically extended and cropped. The picture taking a halfway trade off between alteration and screen coverage. 4:3 Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio. 16:9 Adjust the picture horizontally, in a linear pro-

portion to fill the entire screen. Just Scan Normally the edges of video signals are cropped 1-2%. Just Scan turns off this cropping and shows the complete video. Notes: If there is noise on the edges of the original signal, it will be visible when Just Scan is activated. JJuusstt SSccaann operates only in DTV/CADTV/Component/HDMI-DTV/DVI-DTV

(720p/1080i/1080p) input source. P I C T U R E C O N T R O L 73 PICTURE CONTROL PRESET PICTURE SETTINGS Picture Mode - Preset There are factory presets for picture settings available in the user menus. You can use a preset, change each setting manually, or use the Intelligent Sensor. PICTURE Move Enter Aspect Ratio : 16:9 Picture Mode : Standard Backlight Contrast Brightness Sharpness Color Tint E 80 90 50 60 60 0 R G 1 MENU Select PPIICCTTUURREE. Intelligent Sensor Vivid Standard Cinema Sport Game Expert1 Expert2 Vivid Standard Cinema Sport Game Expert1 Expert2 Vivid Standard Cinema Sport Game Expert1 Expert2 37/42/47/52LG50, 32/37/42/47/52LG60, 32/42/47/52LG70, 42LGX, 47LG90 32/37/42LG30, 42/50PG25 50/60PG60, 50/60PG70 2 3 ENTER 4RETURN MENU ENTER Select PPiiccttuurree MMooddee. Select IInntteelllliiggeenntt SSeennssoorr (Except 32/37/42LG30, Plasma TV), VViivviidd, SSttaannddaarrdd, CCiinneemmaa//

CCiinneemmaa

(Only for 50/60PG60, 50/60PG70) , SSppoorrtt, or GGaammee. Return to the previous menu. Return to TV viewing. I When selecting IInntteelllliiggeenntt SSeennssoorr

(Except 32/37/42LG30, Plasma TV), the most suitable picture is automatically adjusted according to the surrounding conditions. I VV ii vv ii dd, SS tt aa nn dd aa rr dd, CC ii nn ee mm aa //

CCiinneemmaa, SSppoorrtt, and GGaammee Settings are preset for the optimum picture quality at the factory and are not adjustable. I You can also adjust PPiiccttuurree MMooddee in the QQ.. MMeennuu. P I C T U R E C O N T R O L 74 Color Tone - Preset Choose one of three automatic color adjustments. Set to warm to enhance hotter colors such as red, or set to cool to see less intense colors with more blue. PICTURE Move Enter PICTURE Move Enter E 50 60 60 0 Brightness Sharpness Color Tint Advanced Control Reset R G E 50 60 60 0 Brightness Sharpness Color Tint Advanced Control Reset Screen (RGB-PC) TruMotion Demo Screen (RGB-PC) TruMotion Demo Color Temperature FF Medium GG Fresh Contrast Fresh Color R Noise Reduction G Gamma Black Level Eye Care Real Cinema TruMotion Off Off Off Medium Low Off Off High Close 1 MENU 2 ENTER Select PPIICCTTUURREE. Select AAddvvaanncceedd CCoonnttrrooll. ENTER Select CCoolloorr TTeemmppeerraattuurree. 3 4 Select CC oo oo ll, MMeeddiiuumm, or WW aa rr mm. 5RETURN MENU Return to the previous menu. Return to TV viewing. P I C T U R E C O N T R O L 75 PICTURE CONTROL MANUAL PICTURE ADJUSTMENT Picture Mode - User Mode Adjust the picture appearance to suit your preference and viewing situations. LCD TV only: This feature is disable in PPiiccttuurree MMooddee--IInntteelllliiggeenntt SSeennssoorr. 50/60PG60, 50/60PG70 only: This feature is disable in PPiiccttuurree MMooddee--

CCiinneemmaa. Backlight EE 80 EE EE EE Enter PICTURE Move Enter Aspect Ratio : 16:9 Picture Mode : Standard Backlight Contrast Brightness Sharpness Color Tint E 80 90 50 60 60 0 R G Select PPIICCTTUURREE. Select PPiiccttuurree MMooddee. Select VViivviidd, SSttaannddaarrdd, CCiinneemmaa, SSppoorrtt, or GGaammee. Select BBaacckklliigghhtt (Only LCD TV), CCoonnttrraasstt, BBrriigghhttnneessss, SShhaarrppnneessss, CCoolloorr, or TT ii nn tt. Make appropriate adjustments. Return to the previous menu. Return to TV viewing. 1 MENU 2 3 4 5 ENTER ENTER ENTER ENTER 6RETURN MENU P I C T U R E C O N T R O L 76 Picture Mode - Expert Control By segmenting categories, EExxppeerrtt11 and EExxppeerrtt22 provide more categories which users can set as they see fit, offering the optimal picture quality for users. PICTURE Move Enter PICTURE Move Enter Aspect Ratio : 16:9 Picture Mode : Standard Backlight Contrast Brightness Sharpness Color Tint E 80 90 50 60 60 0 R Sport Game Expert1 Expert2 G E 50 60 60 0 Brightness Sharpness Color Tint Expert Control Reset Screen (RGB-PC) TruMotion Demo Fresh Contrast FF Off GG Noise Reduction Gamma G Black Level R Real Cinema Color Standard White Balance Method Red Contrast Green Contrast Blue Contrast E Off Medium Off Off SD Normal 2 Points 50 50 50 1 MENU ENTER ENTER ENTER ENTER 2 3 4 5 6 7RETURN MENU Select PPIICCTTUURREE. Select PPiiccttuurree MMooddee. Select EExxppeerrtt11 or EExxppeerrtt22. Select EExxppeerrtt CCoonnttrrooll. Select your desired menu option. Make appropriate adjustments. Return to the previous menu. Return to TV viewing. P I C T U R E C O N T R O L 77 PICTURE CONTROL PICTURE IMPROVEMENT TECHNOLOGY Fresh Contrast: Optimizes the contrast automatically according to the brightness of the reflection. Fresh Color: Adjusts the color of the reflection automatically to reproduce as close as possible natural colors. Noise Reduction: Removes interference up to the point where it does not damage the original picture. Gamma: High gamma values display whitish images and low gamma values display high contrast images. PICTURE Move Enter PICTURE Move Enter E 50 60 60 0 Brightness Sharpness Color Tint Advanced Control Reset R G E 50 60 60 0 Brightness Sharpness Color Tint Advanced Control Reset Screen (RGB-PC) TruMotion Demo Screen (RGB-PC) TruMotion Demo Color Temperature Medium Fresh Contrast FF Off GG Fresh Color R G Noise Reduction Gamma Black Level Eye Care Real Cinema TruMotion Off Off Medium Low Off Off High Close 1 MENU ENTER ENTER 2 3 4 5RETURN MENU Select PPIICCTTUURREE. Select AAddvvaanncceedd CCoonnttrrooll. Select FFrreesshh CCoonnttrraasstt, FFrreesshh CCoolloorr, NNooiissee RReedduuccttiioonn, or GGaammmmaa. Select your desired options. Return to the previous menu. Return to TV viewing. P I C T U R E C O N T R O L 78 ADVANCED CONTROL - BLACK (DARKNESS) LEVEL Adjusting the contrast and the brightness of the screen using the black level of the screen. This feature is disabled in DTV and RGB-PC mode. PICTURE Move Enter PICTURE Move Enter E 50 60 60 0 Brightness Sharpness Color Tint Advanced Control Reset R G E 50 60 60 0 Brightness Sharpness Color Tint Advanced Control Reset Screen (RGB-PC) TruMotion Demo Screen (RGB-PC) TruMotion Demo Color Temperature Medium Fresh Contrast Fresh Color R G Noise Reduction Gamma Off Off Auto Medium Black Level FF Low GG Eye Care Real Cinema TruMotion Off Off High Close Select PPIICCTTUURREE. Select AAddvvaanncceedd CCoonnttrrooll. I HH ii gg hh: The reflection of the screen gets I LL oo ww: The reflection of the screen gets darker. brighter. I AAuuttoo: Realizing the black level of the screen and set it to High or Low auto-

matically. Select BBllaacckk LLeevveell. Select LL oo ww or HH ii gg hh. Return to the previous menu. Return to TV viewing. 1 MENU ENTER ENTER 2 3 4 5RETURN MENU P I C T U R E C O N T R O L 79 PICTURE CONTROL ADVANCED CONTROL - EYE CARE - LCD TV Only Dims extremely bright pictures. This feature is disabled in PPiiccttuurree MMooddee--VViivviidd, CCiinneemmaa. PICTURE Move Enter PICTURE Move Enter E 50 60 60 0 Brightness Sharpness Color Tint Advanced Control Reset R G E 50 60 60 0 Brightness Sharpness Color Tint Advanced Control Reset Screen (RGB-PC) TruMotion Demo Screen (RGB-PC) TruMotion Demo Color Temperature Medium Fresh Contrast Fresh Color R Noise Reduction G Gamma Black Level Eye Care Real Cinema TruMotion Off Off Off Medium Low FF Off GG Auto High Close 1 MENU ENTER ENTER 2 3 4 5RETURN MENU Select PPIICCTTUURREE. Select AAddvvaanncceedd CCoonnttrrooll. Select EEyyee CCaarree. Select OO nn or OO ff ff. Return to the previous menu. Return to TV viewing. P I C T U R E C O N T R O L 80 ADVANCED CONTROL - REAL CINEMA / FILM MODE Set up the TV for the best picture appearance for viewing movies. When you operate Real Cinema/Film Mode (3:2 Pull-Down Mode or Cinema Correction Mode), the TV will adjust 24 fps video from movies to 30 fps video for display. I Plasma TV, 32/37/42LG30 This feature operates only in TV (Analog TV/CATV, Digital DTV/CADTV), AV1, AV2, Component 480i/1080i, and HDMI 1080i mode. I 37/42/47/52LG50 This feature operates only in TV (Analog TV/CATV, Digital DTV/CADTV), AV1, AV2, Component 480i/1080i, and HDMI 1080i mode. This TV ouputs 48Hz in DTV, Component, and HDMI 1080p (24Hz). I 32/37/42/47/52LG60, 32/42/47/52LG70, 42LGX, 47LG90 This function works with all inputs except PC mode. Screen TruMotion Real Cinema 5:5 Pull-Down 3:2 Pull-Down Off On On On PICTURE Move Enter PICTURE Move Enter E 50 60 60 0 Brightness Sharpness Color Tint Advanced Control Reset R G E 50 60 60 0 Brightness Sharpness Color Tint Advanced Control Reset Screen (RGB-PC) TruMotion Demo Screen (RGB-PC) TruMotion Demo Color Temperature Medium Color Temperature Medium Fresh Contrast Fresh Color R G Noise Reduction Gamma Black Level Film Mode Off Off Off Medium Low FF Off GG Fresh Contrast Fresh Color Noise Reduction Gamma Black Level Eye Care Off Off Off Medium Low Off Close For Plasma TV Real Cinema FF Off GG TruMotion High Close For LCD TV 1 MENU Select PPIICCTTUURREE. 2 3 ENTER Select AAddvvaanncceedd CCoonnttrrooll. ENTER Select RReeaall CCiinneemmaa or FF ii ll mm MM oo dd ee. 4 5RETURN MENU Select OO nn or OO ff ff. Return to the previous menu. Return to TV viewing. P I C T U R E C O N T R O L 81 PICTURE CONTROL ADVANCED CONTROL - TRUMOTION

- Only 32/37/42/47/52LG60, 32/42/47/52LG70, 42LGX, 47LG90 TruMotion provides even better quality for movies than 3:2 Pull-Down conversions. TruMotion means the panel supports faster frame rates that normal panels which makes for smoother motion in video. TruMotion LCD models support 120Hz instead of 60Hz. This means twice the information on the screen in the same amount of time and easier film conversions (120 is equally divisible by 24, so no interpre-

tations or double frames are needed). TruMotion works with all inputs except PC mode. PICTURE Move Enter PICTURE E 50 60 60 0 Brightness Sharpness Color Tint Advanced Control Reset R G Move Enter E 50 60 60 0 Brightness Sharpness Color Tint Advanced Control Reset Color Temperature Fresh Contrast Fresh Color R Noise Reduction G Gamma Screen (RGB-PC) TruMotion Demo Screen (RGB-PC) TruMotion Demo Black Level Eye Care Real Cinema TruMotion Medium Off Off Off Medium Low Off Off FF High GG Close 1 MENU ENTER ENTER 2 3 4 5RETURN MENU Select PPIICCTTUURREE. Select AAddvvaanncceedd CCoonnttrrooll. Select TTrruuMMoottiioonn. Select OO ff ff, LL oo ww, or HH ii gg hh. Return to the previous menu. Return to TV viewing. I HHiigghh: Provides smoother picture movement. I LL oo ww: Provides smooth picture movement. Use this setting for standard use. I OO ff ff: Use this setting when Highand Low setting result in noise. I If you enable "TruMotion", noise may appear on the screen. If this occurs, set "TruMotion" to "Off". P I C T U R E C O N T R O L 82 TRUMOTION DEMO

- Only 32/37/42/47/52LG60, 32/42/47/52LG70, 42LGX, 47LG90 Use this feature to see the difference TruMotion makes. TruMotion works with all inputs except PC mode. PICTURE Move Enter E 50 60 60 0 Brightness Sharpness Color Tint Advanced Control Reset R G Screen (RGB-PC) TruMotion Demo TruMotion On TruMotion Off 1 MENU 2 3 ENTER ENTER 4 MENU Select PPIICCTTUURREE. Select TTrruuMMoottiioonn DDeemmoo. Begin TTrruuMMoottiioonn DDeemmoo. Stop TTrruuMMoottiioonn DDeemmoo. P I C T U R E C O N T R O L 83 PICTURE CONTROL PICTURE RESET Settings of the selected picture modes return to the default factory settings. PICTURE Move Enter PICTURE E 50 60 60 0 Brightness Sharpness Color Tint Advanced Control Reset R G Move Enter E 50 60 60 0 Brightness Sharpness Color Tint Advanced Control Reset ii R G Resetting video configuration... Screen (RGB-PC) TruMotion Demo Screen (RGB-PC) TruMotion Demo 1 MENU 2 3 ENTER ENTER 4 MENU Select PPIICCTTUURREE. Select RReesseett. Initialize the adjusted value. Return to TV viewing. P I C T U R E C O N T R O L 84 POWER INDICATOR - LCD TV Only OPTION Language Input Label SIMPLINK Key Lock Caption Set ID Power Indicator Initial Setting Move Enter

: English

: On

: Off

: Off

: 1

: Home OPTION Language Input Label SIMPLINK Key Lock Caption Set ID Power Indicator Initial Setting Move Enter

: English

: On

: Off

: Off

: 1 Srartup Sound Standby Light Power Light

: Home Demo Mode FF Low GG Off On Off Close Only for 32/37/42/47/52LG60, 42LGX 1 MENU ENTER ENTER 2 3 4 5RETURN MENU Select OOPPTTIIOONN. Select PPoowweerr IInnddiiccaattoorr. Select SS rr aa rr tt uu pp SS oo uu nn dd, SS tt aa nn dd bb yy LLiigghhtt, PPoowweerr LLiigghhtt or DDeemmoo MMooddee. Select your desired options. Return to the previous menu. Return to TV viewing. I SSttaarrttuupp SSoouunndd: You can turn off the starting sound of the TV or set the vol-

ume. I SSttaannddbbyy LLiigghhtt: You can set the brightness of the LED on the front side of the TV during power standby. I PPoowweerr LLiigghhtt: You can set the the LED on the front side of the TV to be turned on or off while watching the TV. I DDeemmoo MMooddee: You can set the LED on the front side of the TV to flash. P I C T U R E C O N T R O L 85 PICTURE CONTROL IMAGE STICKING MINIMIZATION (ISM) METHOD - Plasma TV Only A frozen still picture from a PC/video game displayed on the screen for prolonged periods can result in a ghost image. You can use Orbiter to help prevent image sticking. The other two functions are for removing a ghost image. OPTION Language Input Label SIMPLINK Key Lock Caption ISM Method Power Saving Set ID Move Enter

: English

: On

: Off

: Off

: Normal

: Level 0

: 1 EE Select OOPPTTIIOONN. Select IISSMM MMeetthhoodd. Select NNoorrmmaall,, OOrrbbiitteerr,, IInnvveerrssiioonn or WWhhiittee WWaasshh.. Return to the previous menu. Return to TV viewing. 1 MENU 2 3 ENTER ENTER 4RETURN MENU OPTION Language Input Label SIMPLINK Key Lock Caption ISM Method Power Saving Set ID EE Move Enter

: English

: On

: Off

: Off

: Normal

: Level 0

: 1 Normal Orbiter Inversion White Wash I NNoorrmmaall: If image sticking is never a problem, ISM is not necessary - set to Normal. I OO rr bb ii tt ee rr: Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid a ghost image on the screen, the image will move every 2 min-

utes. I IInnvveerrssiioonn: Inversion will automatically invert the plasma display panel color every 30 minutes. I WW hh ii tt ee WW aa ss hh: White Wash removes ghost images from the screen. Use spar-

ingly. Watch the TV normally for a while before using this feature to see if the ghost image disappears on its own. NOTE

GG An excessive ghosted image may be impossible to clear entirely with White Wash. To return to nor-

mal viewing, press the any button. P I C T U R E C O N T R O L 86 POWER SAVING PICTURE MODE - Plasma TV Only It reduces the plasma displays power consumption. OPTION Language Input Label SIMPLINK Key Lock Caption ISM Method Power Saving Set ID Move Enter

: English

: On

: Off

: Off

: Normal

: Level 0

: 1 EE OPTION Language Input Label SIMPLINK Key Lock Caption ISM Method Power Saving Set ID Move Enter

: English

: On

: Off

: Off

: Normal

: Level 0

: 1 Level 0 Level 1 Level 2 Level 3 Level 4 EE 1 MENU 2 3 ENTER ENTER 4RETURN MENU Select OOPPTTIIOONN. Select PPoowweerr SSaavviinngg. Select LLeevveell 00, LLeevveell 11, LLeevveell 22, LLeevveell 33, or LLeevveell 44. Return to the previous menu. Return to TV viewing. I Level 0 is the brightest. I Level 0 > Level 1 > Level 2 > Level 3 >

Level 4 I You can also adjust PPoowweerr SSaavviinngg in the QQ.. MMeennuu. P I C T U R E C O N T R O L 87 SOUND & LANGUAGE CONTROL AUTO VOLUME LEVELER (AUTO VOLUME) Auto Volume makes sure that the volume level remains consistent whether you are watching a commercial or a regular TV program. AUDIO Auto Volume Clear Voice Balance Sound Mode

: Off

: On Move Enter 0 L R

: Standard SRS TruSurround XT: Off Treble Bass Reset E 50 50 AUDIO Auto Volume Clear Voice Balance Sound Mode

: On

: On Move Enter Off On 0 L R

: Standard SRS TruSurround XT: Off Treble Bass Reset E 50 50 1 MENU Select AAUUDDIIOO. 2 3 ENTER Select AAuuttoo VVoolluummee. ENTER Select OO nn or OO ff ff. 4RETURN MENU Return to the previous menu. Return to TV viewing. S O U N D

L A N G U A G E C O N T R O L 88 PRESET SOUND SETTINGS (SOUND MODE) Sound Mode lets you enjoy the best sound without any special adjustment as the TV sets the appropriate sound options based on the program content. SSttaannddaarrdd, MMuussiicc, CCiinneemmaa, SSppoorrtt, and GG aa mm ee are preset for optimum sound quality at the factory and are not adjustable. AUDIO Auto Volume Clear Voice Balance Sound Mode

: Off

: On Move Enter 0 L R

: Standard SRS TruSurround XT: Off Treble Bass Reset E 50 50 AUDIO Auto Volume Clear Voice Balance Sound Mode

: Off

: On Move Enter 0 L R

: Standard SRS TruSurround XT: Off Treble Bass Reset E Standard Music Cinema Sport Game 50 50 1 MENU Select AAUUDDIIOO. 2 3 ENTER Select SSoouunndd MMooddee. ENTER Select SSttaannddaarrdd, MMuussiicc, CCiinneemmaa, SSppoorrtt, or GGaammee. 4RETURN MENU Return to the previous menu. Return to TV viewing. I You can also adjust SSoouunndd MMooddee in the QQ.. MMeennuu. S O U N D

L A N G U A G E C O N T R O L 89 SOUND & LANGUAGE CONTROL SOUND SETTING ADJUSTMENT - USER MODE Adjust the sound to suit your taste and room situations. AUDIO Auto Volume Clear Voice Balance Sound Mode Move Enter

: Off

: On 0 L R

: Standard SRS TruSurround XT: Off Treble Bass Reset E 50 50 1 MENU 2 ENTER 3 ENTER 4 ENTER Select AAUUDDIIOO. Select SSoouunndd MMooddee. Select SSttaannddaarrdd, MMuussiicc, CCiinneemmaa, SSppoorrtt, or GGaammee. Select TTrreebbllee or BB aass ss. SRS TRUSURROUND XT 1 MENU 2 3 ENTER ENTER 4RETURN MENU Select AAUUDDIIOO. Select SSRRSS TTrruuSSuurrrroouunndd XXTT Select OO nn or OO ff ff. Return to the previous menu. Return to TV viewing. S O U N D

L A N G U A G E C O N T R O L 90 AUDIO Auto Volume Clear Voice Balance Sound Mode 5 ENTER 6RETURN MENU

: Off

: On Move Enter 0 L R

: Standard SRS TruSurround XT: Off Treble Bass Reset E 50 50 Treble Bass SRS TruSurround XT Off EE EE 50 50 Close Make appropriate adjustments. Return to the previous menu. Return to TV viewing. I SSRRSS TTrruuSSuurrrroouunndd XXTT: Takes advantage of any multi-channel format without needing to add extra speakers or equipment. Dialog clarity, bass enrichment, and the addition of stereo audio enhancement produces an immersive sound experience from standard stereo material. CLEAR VOICE By differentiating the human sound range from others, it improves the sound quality of voices. AUDIO Auto Volume Clear Voice Balance Sound Mode

: Off

: On Move Enter 0 L R

: Standard SRS TruSurround XT: Off Treble Bass Reset E 50 50 AUDIO Auto Volume Clear Voice Balance Sound Mode

: Off

: On Move Enter Off On 0 L R

: Standard SRS TruSurround XT: Off Treble Bass Reset E 50 50 1 MENU Select AAUUDDIIOO. 2 3 ENTER Select CClleeaarr VVooiiccee. ENTER Select OO nn or OO ff ff. 4RETURN MENU Return to the previous menu. Return to TV viewing. I If you select CClleeaarr VVooiiccee--OOnn, SS RR SS TT rr uu SS uu rr rr oo uu nn dd XX TT feature will not work. I You can also adjust CClleeaarr VVooiiccee in the QQ--MMeennuu. S O U N D

L A N G U A G E C O N T R O L 91 SOUND & LANGUAGE CONTROL BALANCE Adjust the left/right sound of speaker to suit your taste and room situations. AUDIO Auto Volume Clear Voice Balance Sound Mode Move Enter

: Off

: On 0 L R

: Standard SRS TruSurround XT: Off Treble Bass Reset E 50 50 AUDIO Auto Volume Clear Voice Balance Sound Mode Move Enter

: Off

: On 0 L Balance 0 R EE L R EE

: Standard SRS TruSurround XT: Off Treble Bass Reset E 50 50 Close 1 MENU 2 3 ENTER ENTER 4RETURN MENU Select AAUUDDIIOO. Select BBaallaannccee. Make appropriate adjustments. Return to the previous menu. Return to TV viewing. S O U N D

L A N G U A G E C O N T R O L 92 TV SPEAKERS ON/OFF SETUP Turn the TV speakers off if using external audio equipment. AUDIO Clear Voice Balance Sound Mode TV Speaker E

: On Move Enter 0 L R

: Standard SRS TruSurround XT: Off Treble Bass Reset

: On 50 50 AUDIO Clear Voice Balance Sound Mode TV Speaker 1 MENU Select AAUUDDIIOO. 2 3 ENTER Select TTVV SSppeeaakkeerr. ENTER Select OO nn or OO ff ff. 4RETURN MENU Return to the previous menu. Return to TV viewing. E

: On Move Enter 0 L R

: Standard SRS TruSurround XT: Off Treble Bass Reset

: On 50 50 Off On S O U N D

L A N G U A G E C O N T R O L 93 SOUND & LANGUAGE CONTROL AUDIO RESET Settings of the selected Sound Mode return to the default factory settings.

: Off

: On Move Enter 0 L R Resetting audio configuration... ii

: Standard SRS TruSurround XT: Off Treble Bass Reset E 50 50 AUDIO Auto Volume Clear Voice Balance Sound Mode Move Enter

: Off

: On 0 L R

: Standard SRS TruSurround XT: Off Treble Bass Reset E 50 50 AUDIO Auto Volume Clear Voice Balance Sound Mode 1 MENU 2 3 ENTER ENTER 4 MENU Select AAUUDDIIOO. Select RReesseett. Initialize the adjusted value. Return to TV viewing. S O U N D

L A N G U A G E C O N T R O L 94 STEREO/SAP BROADCAST SETUP For Analog only: This TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accom-

panies the stereo program if the station transmits an additional sound signal. Mono sound is automatically used if the broadcast is only in Mono. Plasma TV Q.Menu LCD TV Q.Menu Aspect Ratio Power Saving Clear Voice Picture Mode Sound Mode Caption Multi Audio Sleep Timer Del/Add/Fav USB Eject CH 16:9 3 Off Vivid Standard Off FF English GG Off Add Eject Aspect Ratio Backlight Clear Voice Picture Mode Sound Mode Caption Multi Audio Sleep Timer Del/Add/Fav USB Eject CH 16:9 3 Off Vivid Standard Off FF English GG Off Add Eject Close Close Analog TV Digital TV 1Q. MENU 2 3 Q. MENU Select SS AA PP. Select MMoonnoo, SStteerreeoo, or SS AA PP. Return to TV viewing. 1Q. MENU 2 3 Q. MENU Select MMuullttii AAuuddiioo. Select other languages. Return to TV viewing. S O U N D

L A N G U A G E C O N T R O L 95 SOUND & LANGUAGE CONTROL AUDIO LANGUAGE Other languages may be available if a digital signal is provided by the broadcasting station. This feature operates only in DTV/CADTV mode. OPTION Language Input Label SIMPLINK Key Lock Caption ISM Method Power Saving Set ID E Move Enter

: English

: On

: Off

: Off

: Normal

: Level 0

: 1 OPTION Language Input Label SIMPLINK Key Lock Caption ISM Method Power Saving Set ID Move Enter

: English Menu Audio

: On

: Off

: Off

: Normal

: Level 0

: 1 E English FF English GG Close 1 MENU ENTER ENTER 2 3 4 5RETURN MENU Select OOPPTTIIOONN. Select LLaanngguuaaggee. Select AAuuddiioo. Select your desired language:

EEnngglliisshh, SSppaanniisshh, or FFrreenncchh Return to the previous menu. Return to TV viewing. S O U N D

L A N G U A G E C O N T R O L 96 ON-SCREEN MENUS LANGUAGE SELECTION The menus can be shown on the screen in the selected language. OPTION Language Input Label SIMPLINK Key Lock Caption ISM Method Power Saving Set ID E Move Enter

: English

: On

: Off

: Off

: Normal

: Level 0

: 1 OPTION Language Input Label SIMPLINK Key Lock Caption ISM Method Power Saving Set ID Move Enter

: English Menu FF English GG English Close Audio

: On

: Off

: Off

: Normal

: Level 0

: 1 E 1 MENU Select OOPPTTIIOONN. 2 3 4 ENTER Select LLaanngguuaaggee. ENTER Select MMeennuu. Select your desired language. From this point on, the on-screen menus will be shown in the selected language. 5RETURN MENU Return to the previous menu. Return to TV viewing. S O U N D

L A N G U A G E C O N T R O L 97 SOUND & LANGUAGE CONTROL CAPTION MODE Analog Broadcasting System Captions Caption must be provided to help people with hearing loss watch TV. Select a caption mode for displaying cap-

tioning information if provided on a program. Analog caption displays information at any position on the screen and is usually the program's dialog. Caption/Text, if provided by the broadcaster, would be available for both digital and analog channels on the Antenna/Cable. This TV is programmed to memorize the caption/text mode which was last set when you turned the power off. This function is only available when CCaappttiioonn Mode is set OO nn. OPTION Language Input Label SIMPLINK Key Lock Caption ISM Method Power Saving Set ID Move Enter

: English

: On

: Off

: Off

: Normal

: Level 0

: 1 E Select OOPPTTIIOONN. OPTION Language Input Label SIMPLINK Key Lock Caption ISM Method Power Saving Set ID Move Enter

: English

: On

: Off

: CC1

: Normal

: Level 0

: 1 E FF Mode On GG CC1 Digital Option Close I When selecting OO ff ff, Sub-menus for Analog, DTV, and Digital Option become disabled. Select CCaappttiioonn. I CCAAPPTTIIOONN The term for the words that scroll across the bottom of the TV screen;

usually the audio portion of the pro-

gram provided for the hearing impaired. I TT EE XX TT The term for the words that appear in a large black frame and almost cover the entire screen; usually messages provid-

ed by the broadcaster. Select OO nn. Select CC CC 11-44 or TTeexxtt11-44. Return to the previous menu. Return to TV viewing. 1 MENU ENTER ENTER 2 3 4 5RETURN MENU S O U N D

L A N G U A G E C O N T R O L 98 Digital Broadcasting System Captions Choose the language you want the DTV/CADTV Captions to appear in. Other Languages can be chosen for digital sources only if they are included on the program. This function in only available when Caption Mode is set On. OPTION Language Input Label SIMPLINK Key Lock Caption ISM Method Power Saving Set ID OPTION Language Input Label SIMPLINK Key Lock Caption ISM Method Power Saving Set ID Move Enter

: English

: On

: Off

: Off

: Normal

: Level 0

: 1 E Select OOPPTTIIOONN. Select CCaappttiioonn. Select OO nn. Select CC CC 11-44, TTeexxtt11-44, or SSeerrvviiccee11 - 66. Return to the previous menu. Return to TV viewing. 1 MENU ENTER ENTER 2 3 4 5RETURN MENU Move Enter

: English FF

: On

: Off

: CC1

: Normal

: Level 0

: 1 Mode On GG CC1 Digital Option E Close S O U N D

L A N G U A G E C O N T R O L 99 SOUND & LANGUAGE CONTROL Caption Option Customize the DTV/CADTV captions that appear on your screen. This function in only available when Caption Mode is set On. OPTION Language Input Label SIMPLINK Key Lock Caption ISM Method Power Saving Set ID Move Enter

: English

: On

: Off

: Off

: Normal

: Level 0

: 1 OPTION Language Input Label SIMPLINK Key Lock Caption ISM Method Power Saving Set ID E E Move Enter

: English

: On

: Off FF

: CC1 Mode

: Normal

: Level 0

: 1 On GG Service1 Digital Option Close FF Size Font Text Color Text Opacity Bg Color Bg Opacity Edge Type Edge Color Custom GG A Standard Font 1 White Solid Black Solid None Black Close I SS ii zz ee: Set the word size. I FFoonntt: Select a typeface for the text. I TTeexxtt CCoolloorr: Choose a color for the text. I TTeexxtt OOppaacciittyy: Specify the opacity for the text color. I BBgg ((BBaacckkggrroouunndd)) CCoolloorr: Select a background color. I BBgg ((BBaacckkggrroouunndd)) OOppaacciittyy: Select the opacity for the background color. I EEddggee TTyyppee: Select an edge type. I EEddggee CCoolloorr: Select a color for the edges. 1 MENU Select OOPPTTIIOONN. 2 3 4 5 6 ENTER ENTER Select CCaappttiioonn Select OO nn. Select DDiiggiittaall OOppttiioonn. ENTER Select CCuussttoomm. Customize the SSttyyllee, FFoonntt, etc., to your preference. A preview icon is provided at the bottom of the screen, use it to see the caption language. 7RETURN MENU Return to the previous menu. Return to TV viewing. S O U N D

L A N G U A G E C O N T R O L 100 TIME SETTING CLOCK SETTING Auto Clock Setup The time is set automatically from a digital channel signal. The digital channel signal includes information for the current time provided by the broadcasting station. Set the clock manually if the current time is set incorrectly by the auto clock function. TIME Move Enter

: Feb/21/2008 2:10 AM Clock

: Off Off Time On Time

: Off Sleep Timer : Off Auto Sleep : Off 1 MENU Select TT II MM EE. ENTER ENTER 2 3 4 5 6RETURN MENU Select CClloocckk. Select AAuuttoo. Select your viewing area time zone. U.S.A: EE aa ss tt ee rr nn, CC ee nn tt rr aa ll, MM oo uu nn tt aa ii nn, PPaacciiffiicc, AAllaasskkaa, or HHaawwaaiiii. Canada: EEaasstteerrnn, CCeennttrraall, MMoouunnttaaiinn, PPaacciiffiicc, NNeeww FF..llaanndd, or AAttllaannttiicc. Select AAuuttoo, OO ff ff, or OO nn (depending on whether or not your viewing area observes Daylight Saving time). Return to the previous menu. Return to TV viewing. FF Auto TIME Move Enter

: Feb/21/2008 2:10 AM Clock

: Off Off Time On Time

: Off Sleep Timer : Off Auto Sleep : Off Year Month Date Hour Minute GG 2008 2 21 2 AM 10 Time Zone Eastern Daylight Saving Auto Close I T M E S E T T I N G 101 FF Manual GG TIME Move Enter

: Feb/21/2008 2:10 AM Clock

: Off Off Time On Time

: Off Sleep Timer : Off Auto Sleep : Off Year Month Date Hour Minute 2008 2 21 2 AM 10 Time Zone Eastern Daylight Saving Auto Close TIME SETTING Manual Clock Setup If the current time setting is wrong, set the clock manually. TIME Move Enter

: Feb/21/2008 2:10 AM Clock

: Off Off Time On Time

: Off Sleep Timer : Off Auto Sleep : Off 1 MENU Select TT II MM EE. ENTER ENTER 2 3 4 5 6RETURN MENU Select CClloocckk. Select MMaannuuaall. Select the Year, Month, Date, Hour, or Minutes option. Set the Year, Month, Date, Hour, or Minutes option. Return to the previous menu. Return to TV viewing. I T M E S E T T I N G 102 AUTO ON/OFF TIME SETTING This function operates only if the current time has been set. The OOffff TTiimmee function overrides the OOnn TTiimmee function if they are both set to the same time. The TV must be in standby mode for the OOnn TTiimmee to work. If you do not press any button within 2 hours after the TV turns on with the OOnn TTiimmee function, the TV will automatically revert to standby mode. TIME Move Enter

: Feb/21/2008 2:10 AM Clock

: Off Off Time On Time

: Off Sleep Timer : Off Auto Sleep : Off TIME Move Enter

: Feb/21/2008 2:10 AM

: Off

: 6:30 AM (Once) Repeat Clock Off Time On Time Sleep Timer : Off Auto Sleep : Off Hour Minute Input Channel Volume FF Once 6 AM GG 30 TV TV 2-0 30 Close 1 MENU Select TT II MM EE. I To cancel OOnn//OOffff TTiimmee function, select OO ff ff. I Only for On Time function ENTER ENTER 2 3 4 5 6RETURN MENU Select OOffff ttiimmee or OOnn ttiimmee. Select RReeppeeaatt. Select OO ff ff, OO nn cc ee, EEvveerryyddaayy, MM oo nn~FF rr ii, MM oo nn~SS aa tt, WWeeeekkeenndd, or SSuunnddaayy. Select and set HHoouurr or MMiinnuuttee. Return to the previous menu. Return to TV viewing. 1 2 3 4 ENTER Select IInnppuutt. Select TTVV, AAVV//AAVV11--22, CCoommppoonneenntt11--22, RRGGBB--PPCC, or HHDDMMII11--44. When Selecting TT VV:

set the channel at turn-on. Adjust to sound level at turn-on. I T M E S E T T I N G 103 TIME SETTING SLEEP TIMER SETTING The Sleep Timer turns the TV off at the preset time. Note that this setting is cleared when the TV is turned off. TIME Move Enter

: Feb/21/2008 2:10 AM Clock

: Off Off Time

: Off On Time Sleep Timer : Off Auto Sleep : Off TIME Move Enter

: Feb/21/2008 2:10 AM Clock

: Off Off Time

: Off On Time Sleep Timer : Off Auto Sleep : Off FF GG Off Close Select TT II MM EE. Select SSlleeeepp TTiimmeerr. Select OO ff ff, 11 00, 22 00, 33 00, 66 00, 99 00, 11 22 00, 11 88 00, or 22 44 00 minutes. I You can also adjust SSlleeeepp TTiimmeerr in the QQ--MMeennuu. Return to the previous menu. Return to TV viewing. 1 MENU 2 3 ENTER ENTER 4RETURN MENU I T M E S E T T I N G 104 AUTO SHUT-OFF SETTING TV will be automatically turned off, in case of no signal for 10 minutes. TIME Move Enter

: Feb/21/2008 2:10 AM Clock

: Off Off Time

: Off On Time Sleep Timer : Off Auto Sleep : Off TIME Move Enter

: Feb/21/2008 2:10 AM Clock

: Off Off Time

: Off On Time Sleep Timer : Off Auto Sleep : On Off On TV will be automatically turned off, in case of No Signal for 10 minutes. 1 MENU 2 3 ENTER ENTER 4RETURN MENU Select TT II MM EE. Select AAuuttoo SSlleeeepp. Select OO nn or OO ff ff. Return to the previous menu. Return to TV viewing. I T M E S E T T I N G 105 PARENTAL CONTROL / RATINGS Parental Control can be used to block specific channels, ratings and other viewing sources. The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broad-

casting station. The default setting is to allow all programs to be viewed. Viewing can be blocked by choosing the type of the program and the categories. It is also possible to block all program viewing for a time period. To use this function, the following must be done :

1. Set ratings and categories to be blocked. 2. Specify a password 3. Enable the lock V-Chip rating and categories Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be blocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-to-

video movies use the Movie Rating System (MPAA) only. Ratings for Television programs including made-for-TV movies :

I TV-G (General audience) I TV-PG (Parental guidance suggested) I TV-14 (Parents strongly cautioned) I TV-MA (Mature audience only) I TV-Y I TV-Y7 (Children 7 years older)

(All children) SET PASSWORD & LOCK SYSTEM Setting up Your Password Set up blocking schemes to block specific channels, ratings, and external viewing sources. A password is required to gain access to this menu. For USA For Canada LOCK Move Enter LOCK Move Enter Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block Lock System : Off Set Password Block Channel TV Rating-English TV Rating-French Downloadable Rating Input Block Enter Password

Close 1 MENU 2 1 4 7 3 6 9 2 5 8 0 ENTER Select LL OO CC KK. Input the password. I Enter the password as requested. I The TV is set up with the initial pass-

word 0-0-0-0. P A R E N T A L C O N T R O L

R A T I N G 106 Lock System Enables or disables the blocking scheme you set up previously. LOCK Move Enter LOCK Move Enter Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block Off On Lock System : On Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block 1 MENU 3 6 9 2 5 8 0 2 1 4 7 3 4 ENTER 5RETURN MENU ENTER Select LL OO CC KK. Input the password. Select LLoocckk SSyysstteemm. Select OO nn or OO ff ff. I When you select OO nn, the Lock System is enable. Return to the previous menu. Return to TV viewing. P A R E N T A L C O N T R O L

R A T I N G 107 PARENTAL CONTROL / RATINGS Set Password Change the password by inputting a new password twice. LOCK Move Enter LOCK Move Enter Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block New

Confirm *

Close Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block 1 MENU ENTER Select LL OO CC KK. 2 1 4 7 3 4 3 6 9 2 5 8 0 Input the password. Select SSeett ppaasssswwoorrdd. ENTER 3 6 9 1 4 7 2 5 8 0 Choose any 4 digits for your new password. As soon as the 4 digits are entered, re-enter the same 4 digits on the CCoonnffiirrmm. 5RETURN MENU Return to the previous menu. Return to TV viewing. P A R E N T A L C O N T R O L

R A T I N G 108 CHANNEL BLOCKING Blocks any channels that you do not want to watch or that you do not want your children to watch. Block/Unblock Move CH Move Page MENU Previous RETURN Exit LOCK Move Enter Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block 1 MENU ENTER Select LL OO CC KK. 2 1 4 7 3 4 5 3 6 9 2 5 8 0 Input the password. Select BBlloocckk CChhaannnneell. ENTER Select a channel to block or unblock. ENTER Block or unblock a channel. 6 MENU RETURN Return to the previous menu. Return to TV viewing. P A R E N T A L C O N T R O L

R A T I N G 109 PARENTAL CONTROL / RATINGS MOVIE & TV RATING Movie Rating (MPAA) - For USA only Blocks movies according to the movie ratings limits specified, so children cannot view certain movies. You can set the ratings limit by blocking out all the movies with the ratings above a specified level. Keep in mind that the movie ratings limit only applies to movies shown on TV, not TV programs, such as soap operas. LOCK Move Enter LOCK Move Enter Blocking off : Permits all programs Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block G PG PG-13 R NC-17 X Blocking Off 1 MENU 2 1 4 7 3 4 3 6 9 2 5 8 0 ENTER 5RETURN MENU ENTER Select LL OO CC KK. Input the password. Select MMoovviiee RRaattiinngg. Select GG, PP GG, PPGG--1133, RR, NNCC--1177, XX, or BBlloocckkiinngg OOffff. Return to the previous menu. Return to TV viewing. I G (General audience) I PG (Parental guidance suggested) I PG-13 (Parents strongly cautioned) I R (Restricted) I NC-17 (No one 17 and under admitted) I X (Adult only) I Blocking Off (Permits all programs) GG If you set PG-13: G and PG movies will be available, PG-13, R, NC-17 and X will be blocked. P A R E N T A L C O N T R O L

R A T I N G 110 TV Rating Children - For USA only Prevents children from watching certain children's TV programs, according to the ratings limit set. The children rating does not apply to other TV programs. Unless you block certain TV programs intended for mature audi-

ences in the TV Rating - sub menu, your children can view those programs. LOCK Move Enter LOCK Move Enter Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block Age Fantasy Violence Close 1 MENU 2 1 4 7 3 4 5 3 6 9 2 5 8 0 ENTER ENTER 6RETURN MENU ENTER Select LL OO CC KK. Input the password. Select TTVV RRaattiinngg--CChhiillddrreenn. Select AA gg ee or FFaannttaassyy VViioolleennccee. I Age (applies to TV-Y, TV-Y7) I Fantasy Violence (applies to TV-Y7) Select block options. Return to the previous menu. Return to TV viewing. P A R E N T A L C O N T R O L

R A T I N G 111 PARENTAL CONTROL / RATINGS TV Rating General - For USA only Based on the ratings, blocks certain TV programs that you and your family do not want to view. LOCK Move Enter Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block Age Dialogue Language Sex Violence Close LOCK Move Enter Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block ENTER Select LL OO CC KK. Input the password. Select TTVV RRaattiinngg--GGeenneerraall. Select AA gg ee, DDiiaalloogguuee, LLaanngguuaaggee, SS ee xx or VViioolleennccee. Select block options. Return to the previous menu. Return to TV viewing. I Age (applies to TV-G,TV-PG,TV-14,TV-

MA). I Dialogue-sexual dialogue (applies to TV-PG,TV-14). I Language-adult language (applies to TV-PG, TV-14, TV-MA). I Sex-sexual situations (applies to TV-PG, TV-14, TV-MA). I Violence (applies to TV-PG, TV-14, TV-

MA). 1 MENU 2 1 4 7 3 4 3 6 9 2 5 8 0 ENTER 5 ENTER 6RETURN MENU P A R E N T A L C O N T R O L

R A T I N G 112 TV Rating English - For CANADA only Selecting canadian english language rating system. LOCK Move Enter LOCK Move Enter Lock System : Off Set Password Block Channel TV Rating-English TV Rating-French Downloadable Rating Input Block Lock System : Off Set Password Block Channel TV Rating-English TV Rating-French Downloadable Rating Input Block Blocking off : Permits all programs E C C8+

G PG 14+

18+

Blocking Off 1 MENU 3 6 9 2 5 8 0 2 1 4 7 3 4 ENTER 5RETURN MENU ENTER Select LL OO CC KK. Input the password. Select TTVV RRaattiinngg--EEnngglliisshh. Select EE, CC, CC88++, GG, PP GG, 1144++, 1188++, or BBlloocckkiinngg OOffff. Return to the previous menu. Return to TV viewing. I E (Exempt) I C (Children) I C8+ (Children eight years and older) I G (General programming, suitable for all audiences) I PG (Parental Guidance) I 14+ (Viewers 14 years and older) I 18+ (Adult programming) I Blocking Off (Permits all programs) P A R E N T A L C O N T R O L

R A T I N G 113 PARENTAL CONTROL / RATINGS TV Rating French - For CANADA only Selecting canadian french language rating system. LOCK Move Enter LOCK Move Enter Blocking off : Permits all programs Lock System : Off Set Password Block Channel TV Rating-English TV Rating-French Downloadable Rating Input Block Lock System : Off Set Password Block Channel TV Rating-English TV Rating-French Downloadable Rating Input Block E G 8ans+

13ans+

16ans+

18ans+

Blocking Off 1 MENU 2 1 4 7 3 4 3 6 9 2 5 8 0 ENTER 5RETURN MENU ENTER Select LL OO CC KK. Input the password. Select TTVV RRaattiinngg--FFrreenncchh. Select EE, GG, 88aannss++, 1133aannss++, 1166aannss++, 1188aannss++, or BBlloocckkiinngg ooffff. Return to the previous menu. Return to TV viewing. I E (Exempt) I G (General) I 8ans+ (General-Not convenient for lit-

tle children) I 13ans+ (Not convenient for children of 13 years and younger) I 16ans+ (Not convenient for children of 16 years and younger) I 18ans+ (This programs is only for adults) I Blocking off (Permits all programs) P A R E N T A L C O N T R O L

R A T I N G 114 DOWNLOADABLE RATING This function may become available in the future and will be available only for digital channels. This function operates only when TV has received Region5 Rating data. LOCK Move Enter LOCK Move Enter Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block E Humor Sport Cruelty Language Sadness Genre Age E Close I Based on rating table, your TV's OSD

(On Screen Display) may differ slightly from what is shown in this manual. 1 MENU 2 1 4 7 3 6 9 2 5 8 0 3 4 5 ENTER ENTER 6RETURN MENU ENTER Select LL OO CC KK. Input the password. Select DDoowwnnllooaaddaabbllee RRaattiinngg. Select desired DDoowwnnllooaaddaabbllee RRaattiinngg option. Select desired option and block it. Return to the previous menu. Return to TV viewing. P A R E N T A L C O N T R O L

R A T I N G 115 PARENTAL CONTROL / RATINGS EXTERNAL INPUT BLOCKING Enables you to block an input. LOCK Move Enter Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block FF GG AV1 AV2 Component1 Component2 RGB-PC HDMI1 HDMI2 HDMI3 Close 32/37/42LG30, 37/42/47/52LG50 FF GG AV1 AV2 Component1 Component2 RGB-PC HDMI1 HDMI2 HDMI3 HDMI4 Close Plasma TV, 32/42/47/52LG70, 47LG90 FF GG AV Component1 Component2 RGB-PC HDMI1 HDMI2 HDMI3 HDMI4 Close 32/37/42/47/52LG60, 42LGX 1 MENU ENTER Select LL OO CC KK. 2 1 4 7 3 4 5 3 6 9 2 5 8 0 Input the password. Select IInnppuutt BBlloocckk. ENTER Select input source. Select OO nn or OO ff ff. 6RETURN MENU Return to the previous menu. Return to TV viewing. P A R E N T A L C O N T R O L

R A T I N G 116 KEY LOCK The TV can be set up so that it can only be used with the remote control. This feature can be used to prevent unauthorized viewing by locking out the front panel controls. This TV is programmed to remember which option it was last set to even if you turn the TV off. OPTION Language Input Label SIMPLINK Key Lock Caption ISM Method Power Saving Set ID Move Enter

: English

: On

: Off

: Off

: Normal

: Level 0

: 1 OPTION Language Input Label SIMPLINK Key Lock Caption ISM Method Power Saving Set ID Move Enter

: English Off On

: On

: On

: Off

: Normal

: Level 0

: 1 E E 1 MENU 2 3 ENTER ENTER 4RETURN MENU Select OOPPTTIIOONN. Select KKeeyy LLoocckk. Select OO nn or OO ff ff. Return to the previous menu. Return to TV viewing. I In KKeeyy LLoocckk OO nn, if the TV is turned off, press the rr / I, INPUT, CH ((DDEE or

)) button on the TV or POWER, INPUT, CH on the remote control. or NUMBER buttons I With the KKeeyy LLoocckk OOnn, the display

KKeeyy LLoocckk appears on the screen if any button on the front panel is pressed while viewing the TV. P A R E N T A L C O N T R O L

R A T I N G 117 APPENDIX TROUBLESHOOTING TThhee ooppeerraattiioonn ddooeess nnoott wwoorrkk nnoorrmmaallllyy.. The remote control doesnt work I Check to see if there is any object between the product and the remote control causing obstruction. Ensure you are pointing the remote control directly at the TV. I Ensure that the batteries are installed with correct polarity (+ to +, - to -). I Ensure that the correct remote operating mode is set: TV, VCR etc. I Install new batteries. Power is suddenly turned off I Is the sleep timer set?

I Check the power control settings. Power interrupted. TThhee vviiddeeoo ffuunnccttiioonn ddooeess nnoott wwoorrkk.. No picture &No sound I Check whether the product is turned on. I Try another channel. The problem may be with the broadcast. I Is the power cord inserted into wall power outlet?

I Check your antenna direction and/or location. I Test the wall power outlet, plug another products power cord into the outlet where the products power cord was plugged in. Picture appears slowly after switching on I This is normal, the image is muted during the product startup process. Please contact your service center, if the picture has not appeared after five minutes. A P P E N D I X No or poor color or poor picture Horizontal/vertical bars or picture shaking I Adjust Color in menu option. I Keep a sufficient distance between the product and the VCR. I Try another channel. The problem may be with the broadcast. I Are the video cables installed properly?

I Activate any function to restore the brightness of the picture. I Check for local interference such as an electrical appliance or power tool. Poor reception on some channels I Station or cable product experiencing problems, tune to another station. I Station signal is weak, reorient antenna to receive weaker station. I Check for sources of possible interference. Lines or streaks in pictures No picture when connecting HDMI 118 I Check antenna (Change the direction of the antenna). I Check HDMI cable over version 1.3. The HDMI cables dont support HDMI version 1.3, it cause flickers or no screen display. In this case use the latest cables that support HDMI version 1.3. TThhee aauuddiioo ffuunnccttiioonn ddooeess nnoott wwoorrkk.. Picture OK & No sound I Press the VOL or VOLUME button. I Sound muted? Press MUTE button. I Try another channel. The problem may be with the broadcast. I Are the audio cables installed properly?

No output from one of the speakers I Adjust Balance in menu option. Unusual sound from inside the product I A change in ambient humidity or temperature may result in an unusual noise when the product is turned on or off and does not indicate a fault with the product. No sound when connecting HDMI/USB I Check HDMI cable over version 1.3. I Check USB cable over version 2.0. I Use normal MP3 file. TThheerree iiss aa pprroobblleemm iinn PPCC mmooddee.. ((OOnnllyy PPCC mmooddee aapppplliieedd)) The signal is out of range I Adjust resolution, horizontal frequency, or vertical frequency. I Check the input source. Vertical bar or stripe on background &

Horizontal Noise &

Incorrect position I Work the Auto configure or adjust clock, phase, or H/V position. (Option) Screen color is unstable or single color I Check the signal cable. I Reinstall the PC video card. A P P E N D I X 119 APPENDIX MAINTENANCE Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can enjoy your new TV. Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning. Cleaning the Screen 1 2 Heres a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until its almost dry, and then use it to wipe the screen. Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV. Cleaning the Cabinet I To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. I Please be sure not to use a wet cloth. Extended Absence CAUTION GG If you expect to leave your TV dormant for a long time (such as a vacation), its a good idea to unplug the power cord to protect against possible damage from lightning or power surges. A P P E N D I X 120 PRODUCT SPECIFICATIONS MODELS With stand Without stand With stand Without stand MODELS With stand Without stand With stand Without stand MODELS With stand Without stand Dimensions

(Width x Height x Depth) Weight Dimensions

(Width x Height x Depth) Weight Dimensions

(Width x Height x Depth) 32LG30

(32LG30-UA)

(32LG30-UD) 37LG30

(37LG30-UA)

(37LG30-UD) 42LG30

(42LG30-UA)

(42LG30-UD) 31.5 x 23.7 x 8.9 inches 801.8 x 604.2 x 227.3 mm 31.5 x 21.4 x 3.1 inches 801.8 x 544.1 x 79.0 mm 36.2 x 26.8 x 11.5 inches 919.6 x 682.3 x 293.8 mm 36.2 x 24.0 x 3.5 inches 919.6 x 610.3 x 89.0 mm 40.6 x 29.2 x 11.5 inches 1032.8 x 742.3 x 293.8 mm 40.6 x 26.3 x 3.6 inches 1032.8 x 670.1 x 92.0 mm 29.5 pounds / 13.4 kg 26.2 pounds / 11.9 kg 41.4 pounds / 18.8 kg 35.7 pounds / 16.2 kg 52.0 pounds / 23.6 kg 46.2 pounds / 21.0 kg 37LG50

(37LG50-UA)

(37LG50-UG) 36.8 x 26.9 x 11.5 inches 936.4 x 685.4 x 293.4 mm 36.8 x 24.1 x 3.4 inches 936.4 x 612.8 x 88.0 mm 42LG50

(42LG50-UA)

(42LG50-UG) 40.7 x 28.9 x 11.5 inches 1034.0 x 735.0 x 294.0 mm 40.7 x 26.1 x 3.5 inches 1034.0 x 663.0 x 91.0 mm 40.3 pounds / 18.3 kg 34.3 pounds / 15.6 kg 54.0 pounds / 24.5 kg 48.5 pounds / 22.0 kg 47LG50

(47LG50-UA)

(47LG50-UG) 52LG50

(52LG50-UA)

(52LG50-UG) 45.5 x 32.0 x 13.5 inches 1156.2 x 813.1 x 342.9 mm 45.5 x 29.1 x 4.0 inches 1156.2 x 739.2 x 103.0 mm 50.8 x 35.1 x 13.5 inches 1291.7 x 892.2 x 342.9 mm 50.8 x 32.1 x 4.5 inches 1291.7 x 817.0 x 115.3 mm Weight With stand Without stand 64.3 pounds / 29.2 kg 54.2 pounds / 24.6 kg 87.0 pounds / 39.5 kg 76.9 pounds / 34.9 kg Power requirement Television System Program Coverage External Antenna Impedance Environment condition Operating Temperature Operating Humidity Storage Temperature Storage Humidity AC100-240V ~ 50/60Hz NTSC-M, ATSC, 64 & 256 QAM VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135 75 ohm 32 ~ 104F (0 ~ 40C) Less than 80%

-4 ~ 140F (-20 ~ 60C) Less than 85%

I The specifications shown above may be changed without prior notice for quality improvement. A P P E N D I X 121 APPENDIX MODELS With stand Without stand With stand Without stand MODELS With stand Without stand With stand Without stand MODELS With stand Without stand With stand Without stand MODELS With stand Without stand Dimensions

(Width x Height x Depth) Weight Dimensions

(Width x Height x Depth) Weight Dimensions

(Width x Height x Depth) Weight Dimensions

(Width x Height x Depth) 32LG60

(32LG60-UA) 37LG60

(37LG60-UA) 42LG60

(42LG60-UA) 31.7 x 24.6 x 13.1 inches 805.6 x 626.0 x 333.0mm 31.7 x 23.1 x 3.7 inches 805.6 x 587.4 x 96.2 mm 36.5 x 27.8 x 14.7 inches 929.0 x 706.9 x 374.7 mm 36.5 x26.1 x 3.8 inches 929.0 x 665.0 x 98.7 mm 40.8 x 31.3 x 14.9 inches 1037.8 x 796.4 x 379.5 mm 40.8 x 29.4 x 3.1 inches 1037.8 x 747.0 x 80.8 mm 31.7 pounds / 14.4 kg 26.8 pounds / 12.2 kg 46.7 pounds / 21.2 kg 39.9 pounds / 18.1 kg 53.1 pounds / 24.1 kg 44.9 pounds / 20.4 kg 42LGX

(42LG61-UA) 47LG60

(47LG60-UA) 52LG60

(52LG60-UA) 40.8 x 31.2 x 14.8 inches 1037.8 x 795.0 x 378.0 mm 40.8 x 29.3 x 1.7 inches 1037.8 x 746.2 x 45.0 mm 45.3 x 34.1 x 17.1 inches 1152.8 x 868.6 x 434.5 mm 50.3 x 37.1 x 16.9 inches 1280.1 x 944.7 x 430.0 mm 45.3 x 32.3 x 3.1 inches 1152.8 x 820.8 x 79.0 mm 50.3 x 35.2 x 3.5 inches 1280.1 x 896.0 x 89.0 mm 47.1 pounds / 21.4 kg 39.6 pounds / 18.0 kg 71.8 pounds / 32.6 kg 59.3 pounds / 26.9 kg 99.2 pounds / 45.0 kg 83.9 pounds / 38.1 kg 32LG70

(32LG70-UA) 31.3 x 23.5 x 8.9 inches 797.0 x 597.0 x 227.3 mm 31.3 x 21.9 x 3.9 inches 797.0 x 558.6 x 100.5 mm 42LG70

(42LG70-UA) 40.4 x 28.8 x 11.5 inches 1026.2 x 734.0 x 293.4 mm 40.4 x 27.0 x 4.4 inches 1026.2 x 687.9 x 111.8 mm 28.4 pounds / 12.9 kg 25.1 pounds / 11.4 kg 49.3 pounds / 22.4 kg 43.4 pounds / 19.7 kg 47LG70

(47LG70-UA) 52LG70

(52LG70-UA) 47LG90

(47LG90-UA) 44.8 x 32.2 x 13.5 inches 1140.4 x 820.1 x 342.9 mm 50.5 x 35.3 x 13.5 inches 1284.4 x 898.6 x 342.9 mm 44.8 x 32.2 x 13.5 inches 1140.4 x 820.1 x 342.9 mm 44.8 x 30.1 x 5.0 inches 50.5 x 33.2 x 5.0 inches 44.8 x 30.1 x 5.0 inches 1140.4 x 764.8 x 129.0 mm 1284.4 x 844.6 x 129.5 mm 1140.4 x 764.8 x 129.0 mm Weight With stand Without stand 66.3 pounds / 30.1 kg 55.9 pounds / 25.4 kg 87.9 pounds / 39.9 kg 77.6 pounds / 35.2 kg 66.3 pounds / 30.1 kg 55.9 pounds / 25.4 kg Power requirement Television System Program Coverage External Antenna Impedance Environment condition Operating Temperature Operating Humidity Storage Temperature Storage Humidity AC100-240V ~ 50/60Hz NTSC-M, ATSC, 64 & 256 QAM VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135 75 ohm 32 ~ 104F (0 ~ 40C) Less than 80%

-4 ~ 140F (-20 ~ 60C) Less than 85%

I The specifications shown above may be changed without prior notice for quality improvement. A P P E N D I X 122 MODELS With stand Without stand With stand Without stand MODELS With stand Without stand Dimensions

(Width x Height x Depth) Weight Dimensions

(Width x Height x Depth) 42PG25

(42PG60-UA) 50PG25

(50PG60-UA) 41.1 x 28.9 x 12.1 inches 48.6 x 33.4 x 14.3 inches 1044.4 x 735.4 x 308.0 mm 1235.6 x 849.3 x 364.1 mm 41.1 x 26.7 x 3.1 inches 1044.4 x 680.6 x 79.6 mm 48.6 x 31.2 x 3.1 inches 1235.6 x 792.8 x 79.6 mm 61.7 pounds / 28.0 kg 55.1 pounds / 25.0 kg 96.3 pounds / 43.7 kg 87.5 pounds / 39.7 kg 50PG60 (50PG60F-UA) 50PG70 (50PG70F-UB) 60PG60 (60PG60F-UA) 60PG70 (60PG70F-UB) 48.6 x 33.4 x 14.3 inches 57.3 x 38.8 x 16.3 inches 1235.6 x 849.3 x 364.1 mm 1455.0 x 985.0 x 414.0 mm 48.6 x 31.2 x 3.1 inches 1235.6 x 792.8 x 79.6 mm 57.3 x 36.4 x 3.3 inches 1455.0 x 924.8 x 84.1 mm Weight With stand Without stand 100.7 pounds / 45.7 kg 91.9 pounds / 41.7 kg 137.5 pounds / 62.4 kg 121.0 pounds / 54.9 kg Power requirement Television System Program Coverage External Antenna Impedance Environment condition Operating Temperature Operating Humidity Storage Temperature Storage Humidity AC100-240V ~ 50/60Hz NTSC-M, ATSC, 64 & 256 QAM VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135 75 ohm 32 ~ 104F (0 ~ 40C) Less than 80%

-4 ~ 140F (-20 ~ 60C) Less than 85%

I The specifications shown above may be changed without prior notice for quality improvement. A P P E N D I X 123 APPENDIX PROGRAMMING THE REMOTE CONTROL The provided universal remote control can be programmed to operate most remote-controllable devices. Note that the remote may not control all models of other brands. Programming a code into a remote mode 1 2 3 4 5 6 Testing your remote control. To find out whether your remote control can operate other components without programming, turn on a component such as a STB and press the corresponding mode button (such as a SS TT BB) on the remote con-

trol, while pointing at the component. Test the PPOOWWEERR and CC HH buttons to see if the component responds correctly. If the component does not operate correctly, the remote control requires programming to operate the device. Turn on the component to be programmed, then press the corresponding mode button (such as SS TT BB) on the remote control. The remote control button of the desired device is illuminated. Press the MMEENNUU and MMUUTTEE buttons simultaneously, and the remote control is ready to be programmed with the code. Enter a code number using the number buttons on the remote control. Programming code numbers for the corresponding component can be found on the following pages. If the code is correct, the device will turn off. Press the MMEENNUU button to store the code. Test the remote control functions to see if the component responds correctly. If not, repeat from step 2. A P P E N D I X 124 Codes Brand Codes Brand Codes Remote Control Code VCR Brand AIWA AKAI 034 016 043 046 124 125 146 072 031 033 103 AMPRO ANAM AUDIO DYNAMICS 012 023 039 043 035 037 129 BROKSONIC 028 031 033 CANON 108 CAPEHART CRAIG 003 040 135 CURTIS MATHES 031 033 041 DAEWOO 005 007 010 064 065 108 110 111 112 116 117 119 108 012 023 039 043 034 053 059 006 017 025 027 029 031 034 035 036 037 046 101 129 131 138 153 003 008 009 010 034 031 033 063 072 107 109 144 147 132 136 012 045 004 018 026 034 043 063 137 150 DAYTRON DBX DYNATECH ELECTROHOME EMERSON FISHER FUNAI GE GO VIDEO HARMAN KARDON HITACHI INSTANTREPLAY 031 033 031 033 JCL 012 013 015 033 JCPENNY 040 066 101 043 012 031 033 043 048 050 055 060 130 150 152 014 034 039 043 047 048 JENSEN JVC KENWOOD LG (GOLDSTAR) 001 012 013 020 101 106 114 123 034 003 009 013 014 017 034 101 106 040 LLOYD LXI MAGIN MAGNAVOX MARANTZ MARTA MATSUI MEI MEMOREX MGA MINOLTA MITSUBISHI MTC MULTITECH NEC NORDMENDE OPTONICA PANASONIC PENTAX PHILCO PHILIPS PILOT PIONEER PORTLAND PULSAR QUARTZ QUASAR RCA REALISTIC RICO RUNCO SALORA 031 033 034 041 067 068 012 031 033 067 069 101 027 030 031 033 003 010 014 031 033 034 053 072 101 102 134 139 045 046 059 013 020 013 020 045 046 049 051 059 061 151 034 040 024 034 012 023 039 043 048 043 053 054 066 070 074 083 133 140 145 013 020 031 033 063 031 034 067 031 033 034 054 067 071 101 101 013 021 048 108 072 011 014 033 066 075 145 013 020 033 034 040 041 062 063 107 109 140 144 145 147 003 008 010 014 031 033 034 040 053 054 101 058 148 014 SEARS SCOTT SAMSUNG SANSUI SANYO SHARP SHINTOM SONY SOUNDESIGN STS SYLVANIA 032 040 102 104 105 107 109 112 113 115 120 122 125 022 043 048 135 003 007 010 014 102 134 017 037 112 129 131 003 008 009 010 013 014 017 020 031 042 073 081 101 031 054 149 024 003 009 031 052 056 057 058 076 077 078 149 034 013 031 033 034 059 067 034 010 034 039 043 034 039 043 031 033 070 019 031 033 034 101 034 006 008 013 042 047 059 082 112 131 040 101 TOTEVISION UNITECH 040 VECTOR RESEARCH 012 VICTOR 048 VIDEO CONCEPTS 012 034 046 VIDEOSONIC WARDS SYMPHONIC TANDY TATUNG TEAC TECHNICS TEKNIKA THOMAS TMK TOSHIBA 040 003 013 017 024 031 033 034 040 053 054 131 012 034 039 043 034 048 056 058 072 080 101 YAMAHA ZENITH A P P E N D I X 125 APPENDIX HDSTB Brand Codes Brand Codes Brand Codes HOUSTON TRACKER 033 037 039 051 HUGHES JANIEL JERROLD KATHREIN LEGEND LG LUTRON LUXOR MACOM 057 104 068 060 147 061 108 057 001 132 062 144 010 059 063 064 065 057 028 124 125 069 070 MEMOREX NEXTWAVE NORSAT PACE SKY SATELLITE 143 060 142 PANASONIC PANSAT 121 PERSONAL CABLE 117 PHILIPS 071 105 PICO 019 102 PRESIDENT PRIMESTAR 030 110 111 PROSAT RCA REALISTIC SAMSUNG SATELLITE SERVICE CO 028 035 047 057 072 066 106 043 074 123 085 SCIENTIFIC ATLANTA 032 138 SONY STARCAST SUPER GUIDE TEECOM 103 041 020 124 125 023 026 075 087 088 090 107 130 137 002 127 016 025 042 043 044 045 048 049 078 079 080 086 101 135 136 115 128 146 081 082 083 084 091 120 TOSHIBA UNIDEN VIEWSTAR WINEGARD ZENITH Brand MITSUBISHI NAD ONKYO PANASONIC PHILIPS PIONEER PROCEED PROSCAN Codes 002 023 008 017 003 009 013 004 026 021 005 006 Brand Codes RCA SAMSUNG SONY THOMPSON TOSHIBA YAMAHA ZENITH 005 006 011 015 007 005 006 019 008 009 018 010 016 025 ALPHASTAR DSR 123 AMPLICA 050 BIRDVIEW 051 126 129 CHANNEL MASTER 013 014 015 018 036 055 008 009 012 077 054 CHAPARRAL CITOH CURTIS MATHES 050 145 DRAKE DX ANTENNA ECHOSTAR 005 006 007 010 011 052 112 116 141 024 046 056 076 038 040 057 058 093 094 095 096 097 098 099 100 122 ELECTRO HOME 089 114 EUROPLUS 017 021 022 027 FUJITSU 133 134 GENERAL INSTRUMENT 003 004 016 029 HITACHI 031 059 101 139 140 DVD Brand Codes 022 020 014 005 006 027 APEX DIGITAL DENON GE HARMAN KARDON JVC LG MAGNAVOX MARANTZ 012 001 010 016 025 013 024 A P P E N D I X 126 IR CODES 1. How to Connect I Connect your wired remote control to the Remote Control port on the TV. 2. Remote Control IR Codes I Output waveform Single pulse, modulated with 37.917KHz signal at 455KHz Tc T1 Carrier frequency FCAR = 1/TC = fOSC/12 Duty ratio = T1/TC = 1/3 I Configuration of frame 1st frame Lead code Low custom code High custom code Data code Data code C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 Repeat frame I Lead code I Repeat code I BBiitt ddeessccrriippttiioonn Bit 0 Repeat code Tf 9 ms 4.5 ms 9 ms 2.25 ms 0.55 ms Bit 1 A P P E N D I X 0.56 ms 1.12 ms 0.56 ms 2.24 ms I FFrraammee iinntteerrvvaall:: TTff The waveform is transmitted as long as a key is depressed. Tf Tf Tf=108ms @455KHz 127 APPENDIX Code

(Hexa) Function Note Code

(Hexa) Function Note 08 45 43 0B POWER Q.MENU MENU INPUT Remote control Button (Power On/Off) D6 TV Discrete IR Code Remote control Button

(TV Input Selection) Remote control Button C4 POWER ON Discrete IR Code Remote control Button

(Only Power On) 10-19 Number Key 0-9 Remote control Button C5 POWER OFF Discrete IR Code 4C 1A 09 02 03 00 01 1E 40 41 07 06 44 5B 7E 30 B0 BA B1 BD 8F 8E

- (Dash) FLASHBK MUTE VOL +

VOL -

CH CH FAV ENTER RETURN SIMPLINK AV MODE PLAY PAUSE STOP REC REW FF Remote control Button

(Only Power Off) Remote control Button 5A AV or AV1 Discrete IR Code Remote control Button

(AV or AV1 Input Selection) Remote control Button D0 AV2 Discrete IR Code Remote control Button

(AV2 Input Selection) Remote control Button BF COMPONENT1 Discrete IR Code Remote control Button

(Component1 Input Selection) Remote control Button D4 COMPONENT2 Discrete IR Code Remote control Button

(Component2 Input Selection) Remote control Button D5 RGB-PC Discrete IR Code Remote control Button

(RGB-PC Input Selection) Remote control Button CE HDMI1 Discrete IR Code Remote control Button

(HDMI1 Input Selection) Remote control Button CC HDMI2 Discrete IR Code Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button E9 DA 76 77 AF

(HDMI2 Input Selection) HDMI3 Discrete IR Code

(HDMI3 Input Selection) HDMI4 Discrete IR Code

(HDMI4 Input Selection) Ratio 4:3 Discrete IR Code

(Only 4:3 Mode) Ratio 16:9 Discrete IR Code

(Only 16:9 Mode) Ratio Zoom Discrete IR Code

(Only Zoom1 Mode)

* Use this feature depending on your model. A P P E N D I X 128 EXTERNAL CONTROL THROUGH RS-232C

- Except 32/37/42/47/52LG60, 42LGX The RS-232C port allows you connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) to control the TVs functions externally. I Note: RS-232C on this unit is intended to be used with third party RS-232C control hardware and software. The instructions below are provided to help with programming software or to test functionality using telenet software. RS-232C Setup i.e) CABLE IN REMOTE CONTROL IN DIGITAL AUDIO OUT OPTICAL COAXIAL RS-232C IN

(CONTROL & SERVICE) AUDIO OUT R S-VIDEO VIDEO L

(MONO) AUDIO R 1 N I V A PC Type of Connector; D-Sub 9-Pin Male Communication Parameters I Baud rate : 9600 bps (UART) I Data length : 8 bits I Parity : None I Stop bit : 1 bit I Communication code : ASCII code I Use a crossed (reverse) cable.

NOTE GG This product has command echo back in the RS-232C Command. No. Pin Name 1 2 3 4 5 6 7 8 9 No connection RXD (Receive data) TXD (Transmit data) DTR (DTE side ready) GND DSR (DCE side ready) RTS (Ready to send) CTS (Clear to send) No Connection 1 6 5 9 A P P E N D I X 129 APPENDIX RS-232C Configurations Either cable below can be used. 7-Wire Configuration

(Serial female-female NULL modem cable) PC TV RXD TXD GND DTR DSR RTS CTS 2 3 5 4 6 7 8 3 2 5 6 4 8 7 TXD RXD GND DSR DTR CTS RTS 3-Wire Configurations

(Not standard) PC TV RXD TXD GND DTR DSR RTS CTS 2 3 5 4 6 7 8 3 2 5 6 4 7 8 TXD RXD GND DTR DSR RTS CTS D-Sub 9 D-Sub 9 D-Sub 9 D-Sub 9 OPTION Language Input Label SIMPLINK Key Lock Caption ISM Method Power Saving Set ID Move Enter

: English

: On

: Off

: Off

: Level 0

: 1 FF 1 EE GG Close Set ID Use this function to specify a TV ID number. Refer to Real Data Mapping1. GG pp..113333. OPTION Language Input Label SIMPLINK Key Lock Caption ISM Method Power Saving Set ID Move Enter

: English

: On

: Off

: Off

: Level 0

: 1 EE Select OOPPTTIIOONN. Select SSeett IIDD. Choose the desired TV ID number. The adjustment range of Set ID is 1~99. Return to the previous menu. Return to TV viewing. A P P E N D I X 130 1 MENU 2 3 ENTER ENTER 4RETURN MENU Command Reference List CCOOMMMMAANNDD11 CCOOMMMMAANNDD22 DATA

(Hexadecimal) CCOOMMMMAANNDD11 CCOOMMMMAANNDD22 DATA

(Hexadecimal) 01. Power 02. Input Select 03. Aspect Ratio 04. Screen Mute 05. Volume Mute 06. Volume Control 07. Contrast 08. Brightness 09. Color 10. Tint 11. Sharpness 12. OSD Select 13. Remote Control Lock Mode k x k k k k k k k k k k k a b c d e f g h i j k l m 00 ~ 01

(GG p.132)

(GG p.132) 00 ~ 01 00 ~ 01 00 ~ 64 00 ~ 64 00 ~ 64 00 ~ 64 00 ~ 64 00 ~ 64 00 ~ 01 00 ~ 01 14. Treble 15. Bass 16. Balance 17. Color Temperature 18. ISM Method 19. Power Saving 20. Auto Configuration 22. Channel Add/Del 23. Key 24. Backlight k k k k j j j m m m Only Plasma TV Model r s t u p q u b c g 00 ~ 64 00 ~ 64 00 ~ 64 00 ~ 02

(GG p.134) 00 ~ 01

(GG p.134) 00 ~ 01

(GG p.135) 00 ~ 64 Only LCD TV Model CCOOMMMMAANNDD11 CCOOMMMMAANNDD22 DATA00 DATA01 DATA02 DATA03 DATA04 DATA05

(Hexadecimal)

(Hexadecimal)

(Hexadecimal)

(Hexadecimal)

(Hexadecimal)

(Hexadecimal) 21. Channel Tuning m a physical major major low minor high minor low attribute program high program low Transmission / Receiving Protocol TTrraannssmmiissssiioonn

[[CCoommmmaanndd11]][[CCoommmmaanndd22]][[ ]][[SSeett IIDD]][[ ]][[DDaattaa]][[CCrr]]

[Command 1] : First command to control the set.(j, k, m or x)

[Command 2] : Second command to control the set.

[Set ID] : You can adjust the set ID to choose desired TV ID number in Setup menu. Adjustment range is 1~ 99. When selecting Set ID 0, every connected the TV is controlled. Set ID is indicated as decimal (1~ 99) on menu and as Hexa decimal (0x0~ 0x63) on transmission

/receiving protocol.

[DATA] : To transmit the command data. Transmit the FF data to read status of command.

[Cr] : Carriage Return ASCII code 0x0D

[ ] : ASCII code space (0x20)

* In this model, TV will not send the status during the standby mode. OOKK AAcckknnoowwlleeddggeemmeenntt

[[CCoommmmaanndd22]][[ ]][[SSeett IIDD]][[ ]][[OOKK]][[DDaattaa]][[xx]]

The TV transmits ACK (acknowledgement) based on this for-

mat when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer.

* In this model, TV will not send the status during the standby mode.

* Data Format

[Command 2] : Use as command.

[Set ID] : Use the small character, if set ID is 10, it will send the 0, a.

[DATA] : Use the small character, if data is 0 x ab, it will send the a, b.

[OK] : Use the large character. EErrrroorr AAcckknnoowwlleeddggeemmeenntt

[[CCoommmmaanndd22]][[ ]][[SSeett IIDD]][[ ]][[NNGG]][[DDaattaa]][[xx]]

The TV transmits ACK (acknowledgement) based on this for-

mat when receiving abnormal data from non-viable functions or communication errors. Data1: Illegal Code Data2: Not supported function Data3: Wait more time

* In this model, TV will not send the status during the standby mode.

* Data Format

[Command 2] : Use as command.

[Set ID] : Use the small character, if set ID is 10, it will send the 0, a.

[DATA] : Use the small character, if data is 0 x ab, it will send the a, b.

[NG] : Use the large character A P P E N D I X 131 0055.. VVoolluummee MMuuttee ((CCoommmmaanndd:: kk ee)) To control volume mute on/off. You can also adjust mute using the MUTE button on remote control. Transmission [k][e][ ][Set ID][ ][Data][Cr]

Data 00: Volume mute on (Volume off) Data 01: Volume mute off (Volume on) Acknowledgement [e][ ][Set ID][ ][OK/NG][Data][x]

0066.. VVoolluummee CCoonnttrrooll ((CCoommmmaanndd:: kk ff)) To adjust volume. You can also adjust volume with the volume buttons on remote control. Transmission [k][f][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)

*Refer to Real data mapping. See page 133. Acknowledgement [f][ ][Set ID][ ][OK/NG][Data][x]

0077.. CCoonnttrraasstt ((CCoommmmaanndd:: kk gg)) To adjust screen contrast. You can also adjust contrast in the PICTURE menu. Transmission [k][g][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)

*Refer to Real data mapping. See page 133. Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]

0088.. BBrriigghhttnneessss ((CCoommmmaanndd:: kk hh)) To adjust screen brightness. You can also adjust brightness in the PICTURE menu. Transmission [k][h][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)

*Refer to Real data mapping. See page 133. Acknowledgement [h][ ][Set ID][ ][OK/NG][Data][x]

APPENDIX 0011.. PPoowweerr ((CCoommmmaanndd:: kk aa)) To control Power On/Off of the TV. Transmission [k][a][ ][Set ID][ ][Data][Cr]

Data 00: Power Off Data 01: Power On Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x]

* In a like manner, if other functions transmit FF data based on this format, Acknowledgement data feedback presents status about each function.

* Note: In this model, TV will send the Acknowledge after power on processing completion. There might be a time delay between command and acknowledge. 0022.. IInnppuutt SSeelleecctt ((CCoommmmaanndd:: xx bb)) To select input source for TV. Transmission [x][b][ ][Set ID][ ][Data][Cr]

Data 00: DTV (Antenna) Data 01: DTV (Cable) Data 10: Analog (Antenna) Data 11: Analog (Cable) Data 20: AV1 Data 21: AV2 Data 40: Component 1 Data 41: Component 2 Data 60: RGB-PC Data 90: HDMI1 Data 91: HDMI2 Data 92: HDMI3 Data 93: HDMI4 Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]

* Use the feature depending on your model. 0033.. AAssppeecctt RRaattiioo ((CCoommmmaanndd:: kk cc)) To adjust the screen format. Transmission [k][c][ ][Set ID][ ][Data][Cr]

Data 01: 4:3 05: Zoom 2 02: 16:9 06: Set by program 04: Zoom 1 09: Just scan A P P E N D I X Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]

Reserved 0044.. SSccrreeeenn MMuuttee ((CCoommmmaanndd:: kk dd)) To select screen mute on/off. Transmission [k][d][ ][Set ID][ ][Data][Cr]

Data 00: Screen mute off (Picture on) Data 01: Screen mute on (Picture off) Acknowledgement [d][ ][Set ID][ ][OK/NG][Data][x]

132 0099.. CCoolloorr ((CCoommmmaanndd:: kk ii)) To adjust screen color. 1144.. TTrreebbllee ((CCoommmmaanndd:: kk rr)) To adjust treble. You can also adjust color in the PICTURE menu. You can also adjust treble in the AUDIO menu. Transmission [k][i][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)

*Refer to Real data mapping as shown below. Transmission [k][r][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)

*Refer to Real data mapping as shown. Acknowledgement [i][ ][Set ID][ ][OK/NG][Data][x]

Acknowledgement [r][ ][Set ID][ ][OK/NG][Data][x]

1100.. TTiinntt ((CCoommmmaanndd:: kk jj)) To adjust screen tint. 1155.. BBaassss ((CCoommmmaanndd:: kk ss)) To adjust bass. You can also adjust tint in the PICTURE menu. You can also adjust bass in the AUDIO menu. Transmission [k][j][ ][Set ID][ ][Data][Cr]

Data Red: 00 ~ Green: 64 (*transmit by Hexadecimal code)

*Refer to Real data mapping as shown below. Transmission [k][s][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)

*Refer to Real data mapping as shown below. Acknowledgement [ j ][ ][Set ID][ ][OK/NG][Data][x]

Acknowledgement [s][ ][Set ID][ ][OK/NG][Data][x]

1111.. SShhaarrppnneessss ((CCoommmmaanndd:: kk kk)) To adjust screen sharpness. 1166.. BBaallaannccee ((CCoommmmaanndd:: kk tt)) To adjust balance. You can also adjust sharpness in the PICTURE menu. You can also adjust balance in the AUDIO menu. Transmission [k][k][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)

*Refer to Real data mapping as shown below. Transmission [k][t][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)

*Refer to Real data mapping as shown below. Acknowledgement [k][ ][Set ID][ ][OK/NG][Data][x]

Acknowledgement [t][ ][Set ID][ ][OK/NG][Data][x]

1122.. OOSSDD SSeelleecctt ((CCoommmmaanndd:: kk ll)) 1177.. CCoolloorr TTeemmppeerraattuurree ((CCoommmmaanndd:: kk uu)) To select OSD (On Screen Display) on/off. Transmission [k][l][ ][Set ID][ ][Data][Cr]

To adjust color temperature. You can also adjust color temperature in the PICTURE menu. Data 00: OSD off Data 01: OSD on Transmission [k][u][ ][Set ID][ ][Data][Cr]

Acknowledgement [l][ ][Set ID][ ][OK/NG][Data][x]

Data 00: Medium 01: Cool 02: Warm Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]

1133.. RReemmoottee CCoonnttrrooll LLoocckk MMooddee ((CCoommmmaanndd:: kk mm)) To lock the remote control and the front panel controls on the set. Transmission [k][m][ ][Set ID][ ][Data][Cr]

Data 00: Lock off Data 01: Lock on Acknowledgement [m][ ][Set ID][ ][OK/NG][Data][x]

If youre not using the remote control and front panel controls on the TV, use this mode. When main power is on/off, remote control lock is released.

*Real data mapping 0 : Step 0 A : Step 10 (SET ID 10) F : Step 15 (SET ID 15) 10 : Step 16 (SET ID 16) 63 : Step 99 (SET ID 99) 64 : Step 100 A P P E N D I X 133 APPENDIX 1188.. IISSMM MMeetthhoodd ((CCoommmmaanndd:: jj pp))

(Only Plasma TV model) To avoid having a fixed image remain on screen. Transmission [ j ][p][ ][Set ID][ ][Data][Cr]

Data 01: Inversion 02: Orbiter 04: White Wash 08: Normal Acknowledgement [p][ ][Set ID][ ][OK/NG][Data][x]

1199.. PPoowweerr ssaavviinngg ((CCoommmmaanndd:: jj qq))

(Only Plasma TV model) To control the power saving function on/off. Transmission [ j ][q][ ][Set ID][ ][Data][Cr]

Data 00: Power saving off (Power Saving Level 0) 01: Power saving on (Power Saving Level 4) Acknowledgement [q][ ][Set ID][ ][OK/NG][Data][x]

2200.. AAuuttoo CCoonnffiigguurraattiioonn ((CCoommmmaanndd:: jj uu)) To adjust picture position and minimize image shaking automatically. Auto configuration only works in RGB-PC mode. Transmission [ j ][u][ ][Set ID][ ][Data][Cr]

Data 1: To set Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]

2211.. CChhaannnneell TTuunniinngg ((CCoommmmaanndd:: mm aa)) To tune channel to following physical/major/minor number. Transmission [m][a][ ][Set ID][ ][Data00][ ][Data01]

[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]

Digital channels have a Physical, Major, and Minor channel number. The Physical number is the actual digital channel number, the Major is the number that the channel should be mapped to, and the Minor is the sub-channel. Since the ATSC tuner automatically maps the channel to the Major number, the Physical number is not required when sending a command. Data 00: Physical Channel Number NTSC air: 02~45, NTSC cable: 01, 0E~7D ATSC air: 01~45, ATSC cable: 01~87 Data 01 & 02: Major Channel Number Data 01: High byte Data 02: Low byte Two bytes are available for the Major and Minor, nor-

mally only the second byte is used. Data 03 & 04: Minor Channel Number Not needed for NTSC. A P P E N D I X 134 Data05:

7 0 1 Main/Sub Picture Main Sub 6 0 1 Two/One Part Channel Two One 5 0 1 Using Physical Channel 4 Reserved Use No Use x x x x x x x x x x 3 0 0 0 0 0 0 0 0 x 1 2 0 0 0 0 1 1 1 1 x 1 1 0 0 1 1 0 0 1 1 x 1 0 0 1 0 1 0 1 0 1 x 1 Step NTSC Air NTSC Cable ATSC Air ATSC Cable_std ATSC Cable_hrc ATSC Cable_irc ATSC cable_auto Reserved

... Reserved 2222.. CChhaannnneell AAdddd//DDeell ((CCoommmmaanndd:: mm bb)) To add and delete the channels Transmission [m][b][ ][Set ID][ ][Data][Cr]

Data 00: Channel Delete Data 01: Channel Add Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]

2233.. KKeeyy ((CCoommmmaanndd:: mm cc)) To send IR remote key code. Transmission [m][c][ ][Set ID][ ][Data][Cr]

Data Key code: Refer to page 128. Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]

2244.. BBaacckklliigghhtt ((CCoommmmaanndd:: mm gg))

(Only LCD TV model) To adjust screen backlight. Transmission [m][g][ ][Set ID][ ][Data][Cr]

Data Min:00 ~ Max:64 (*transmit by Hexadecimal code)

*Refer to Real data mapping 1. See page 133. Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]

The table above lists the binary code which must be converted to Hexadecimal before sending. For example:

The binary code to tune the sub source to an NTSC cable channel is 1000 0001, which translates to 81 in Hex.

* 7th bit : For which source do you want to change the channel.

* 6th bit: Use a two part or one part channel. Most cases just use 0 since its ignored when using NTSC.

* 5th bit: Use 0 with NTSC since it can only use the phys-

ical channel number. Normally use 1 for ATSC since most times it doesnt matter what the physical number is.

* 4th bit: Set to 0.

* 3-0 bits: Choose signal type.

* Tune Command Examples:

1. Tune to the analog (NTSC) cable channel 35. Data 00 = Physical of 35 = 23 Data 01 & 02 = No Major = 00 00 Data 03 & 04 = No Minor = 00 00 Data 05 = 0000 0001 in binary = 01 Total = ma 00 23 00 00 00 00 01 2. Tune to the digital (ATSC) local channel 30-3. Data 00 = Dont know Physical = 00 Data 01 & 02 = Major is 30 = 00 1E Data 03 & 04 = Minor is 3 = 00 03 Data 05 = 0010 0010 in binary = 22 Total = ma 00 00 00 1E 00 03 22 Acknowledgement[a][ ][Set ID][ ][OK][Data00][Data01]

[Data02][Data03][Data04][x][a][ ][Set ID]

[ ][NG][Data00][x]

A P P E N D I X 135 APPENDIX OPEN SOURCE LICENSE - This feature is not available for all models. GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all. Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software - to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation's software and to any other program whose authors commit to using it. (Some other free software foundation software is covered by the GNU Lesser General Public License instead.) You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things. To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it. For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. We protect your rights with two steps: (1) copyright the soft-

ware, and (2) offer you this license which gives you legal permis-

sion to copy, distribute and/or modify the software. Also, for each author's protection and ours, we want to make cer-

tain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations. The precise terms and conditions for copying, distribution and modification follow. GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This license applies to any program or other work which con-

tains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The

"Program", below, refers to any such program or work, and a

"work based on the Program" means either the Program or any derivative work under copyright law: that is to say, a work con-

taining the Program or a portion of it, either verbatim or with modifications and/or translated into another language.

(Hereinafter, translation is included without limitation in the term "modification".) Each licensee is addressed as "you". Activities other than copying, distribution and modification are not covered by this license; they are outside its scope. The act of running the Program is not restricted, and the out-

put from the program is covered only if its contents constitute a work based on the program (independent of having been made by running the program). Whether that is true depends on what the program does. 1. You may copy and distribute verbatim copies of the program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this license and to the absence of any warranty; and give any other recipients of the program a copy of this license along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of section 1 above, provided that you also meet all of these conditions:

Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change. A P P E N D I X 136 b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part there of, to be licensed as a whole at no charge to all third parties under the terms of this license. c) If the modified program normally reads commands interac-

tively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this license.

(Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this license, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the dis-

tribution of the whole must be on the terms of this license, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or con-

test your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the program. In addition, mere aggregation of another work not based on the program with the Program (or with a work based on the program) on a volume of a storage or distribution medium does not bring the other work under the scope of this license. 3. You may copy and distribute the program (or a work based on it, under section 2) in object code or executable form under the terms of sections 1 and 2 above provided that you also do one of the following:

a) Accompany it with the complete corresponding machine-

readable source code, which must be distributed under the terms of sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of sections 1 and 2 above on a medium customarily used for software interchange; or, c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alter-

native is allowed only for noncommercial distribution and only if you received the program in object code or exe-

cutable form with such an offer, in accord with Subsection b above.) The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all mod-

ules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by offer-

ing access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. 4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this license. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this license. However, parties who have received copies, or rights, from you under this license will not have their licens-

es terminated so long as such parties remain in full compli-

ance. 5. You are not required to accept this license, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this license. Therefore, by modifying or distributing the program

(or any work based on the program), you indicate your accep-

tance of this license to do so, and all its terms and conditions for copying, distributing or modifying the program or works based on it. 6. Each time you redistribute the program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforc-

ing compliance by third parties to this license. A P P E N D I X 137 APPENDIX any later version published by the Free Software Foundation. If the program does not specify a version number of this license, you may choose any version ever published by the Free Software Foundation. 10.If you wish to incorporate parts of the program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copy-

righted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of pro-

moting the sharing and reuse of software generally. NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLD-

ERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 12.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PRO-

GRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUS-

TAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. 7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the con-

ditions of this license, they do not excuse you from the con-

ditions of this license. If you cannot distribute so as to satis-

fy simultaneously your obligations under this license and any other pertinent obligations, then as a consequence you may not distribute the program at all. For example, if a patent license would not permit royalty-free redistribution of the program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this license would be to refrain entirely from distribution of the program. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest valid-

ity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution sys-

tem, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this license. 8. If the distribution and/or use of the program is restricted in certain countries either by patents or by copyrighted inter-

faces, the original copyright holder who places the program under this license may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this license incorporates the limitation as if written in the body of this license. 9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present ver-

sion, but may differ in detail to address new problems or con-

cerns. Each version is given a distinguishing version number. If the program specifies a version number of this license which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of A P P E N D I X 138 END OF TERMS AND CONDITIONS How to apply these terms to your new programs If you develop a new program, and you want it to be of the great-

est possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effective-

ly convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to where the full notice is found. one line to give the program's name and a brief idea of what it does. Copyright (C) <year> <name of author>

This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the license, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-

POSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. Also add information on how to contact you by electronic and paper mail. If the program is interactive, make it output a short notice like this when it starts in an interactive mode:

Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type show w. This is free software, and you are welcome to redistribute it under certain conditions; type show c for details. The hypothetical commands show w and show c should show the appropriate parts of the General Public License. Of course, the commands you use may be called something other than show w and show c; they could even be mouse-clicks or menu items-whatever suits your program. You should also get your employer (if you work as a programmer) or your school, if any, to sign a copyright disclaimer for the pro-

gram, if necessary. Here is a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the pro-

gram Gnomovision (which makes passes at compilers) written by James Hacker. signature of Ty Coon, 1 April 1989 Ty Coon, President of Vice This General Public License does not permit incorporating your program into proprietary programs. If your program is a subrou-

tine library, you may consider it more useful to permit linking pro-

prietary applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of this license. A P P E N D I X 139 APPENDIX GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999 Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, ver-

sion 2, hence the version number 2.1.]

Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software - to make sure the software is free for all its users. This license, the Lesser General Public License, applies to some specially designated software packages - typically libraries - of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think careful-

ly about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below. When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free soft-

ware (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things. To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it. For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights. We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library. To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is mod-

ified by someone else and passed on, the recipients should know that what they have is not the original version, so that the origi-

nal author's reputation will not be affected by problems that might be introduced by others. Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company can-

not effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license. Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to per-

mit linking those libraries into non-free programs. When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library. We call this license the "Lesser" General Public License because it does Less to protect the user's freedom than the ordinary General Public License. It also provides other free software devel-

opers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license pro-

vides advantages in certain special circumstances. For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License. In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system. A P P E N D I X 140 Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library. each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this license and to the absence of any warranty; and distribute a copy of this license along with the Library. The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a "work based on the library" and a "work that uses the library". The former contains code derived from the library, whereas the latter must be combined with the library in order to run. GNU LESSER GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This license agreement applies to any software library or other program which contains a notice placed by the copyright hold-

er or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called this license). Each license is addressed as "you". A library means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables. The Library, below, refers to any such software library or work which has been distributed under these terms. A work based on the Library means either the Library or any derivative work under copyright law: that is to say, a work containing the library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language.

(Hereinafter, translation is included without limitation in the term modification.) Source code for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it con-

tains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library. Activities other than copying, distribution and modification are not covered by this license; they are outside its scope. The act of running a program using the Library is not restrict-

ed, and output from such a program is covered only if its con-

tents constitute a work based on the library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the library does and what the program that uses the library does. 1. You may copy and distribute verbatim copies of the library's complete source code as you receive it, in any medium, pro-

vided that you conspicuously and appropriately publish on You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of section 1 above, provided that you also meet all of these conditions:

a) The modified work must itself be a software library. b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change. c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this license. d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.

(For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application. Therefore, Subsection 2d requires that any appli-

cation-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the library, and can be reasonably considered independent and separate works in themselves, then this license, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the library, the dis-

tribution of the whole must be on the terms of this license, whose permissions for other licenses extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or con-

test your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the library. In addition, mere aggregation of another work not based on the library with the library (or with a work based on the library) on a volume of a storage or distribution medium does not bring the other work under the scope of this license. A P P E N D I X 141 APPENDIX 3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices. Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code of the library into a program that is not a library. 4. You may copy and distribute the library (or a portion or deriv-

ative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-

readable source code, which must be distributed under the terms of sections 1 and 2 above on a medium customarily used for software interchange. If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code. 5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a work that uses the Library. Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this license. However, linking a work that uses the library with the Library creates an executable that is a derivative of the Library

(because it contains portions of the library), rather than a work that uses the library. The executable is therefore cov-

ered by this license. Section 6 states terms for distribution of such executable. When a work that uses the library uses material from a head-

er file that is part of the library, the object code for the work may be a derivative work of the library even though the source code is not. Whether this is true is especially significant if the work can be linked without the library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law. If such an object file uses only numerical parameters, data structure layouts and accessories, and small macros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legal-

ly a derivative work. (Executable containing this object code plus portions of the library will still fall under Section 6.) Otherwise, if the work is a derivative of the library, you may distribute the object code for the work under the terms of Section 6. Any executable containing that work also fall under Section 6, whether or not they are linked directly with the library itself. 6. As an exception to the sections above, you may also combine or link a "work that uses the library" with the library to pro-

duce a work containing portions of the library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer's own use and reverse engineering for debugging such modifications. You must give prominent notice with each copy of the work that the library is used in it and that the Library and its use are covered by this license. You must supply a copy of this license. If the work during execution displays copyright notices, you must include the copyright notice for the library among them, as well as a reference directing the user to the copy of this license. Also, you must do one of these things:

a) Accompany the work with the complete corresponding machine-readable source code for the library including whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable work that uses the Library, as object code and/or source code, so that the user can modify the library and then relink to produce a modified executable containing the modified library. (It is understood that the user who changes the contents of definitions files in the library will not necessarily be able to recompile the appli-

cation to use the modified definitions.) b) Use a suitable shared library mechanism for linking with the library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the users computer system, rather than copying library functions into the exe-

cutable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with. c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6, above, for a charge no more than the cost of performing this distribution. d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place. e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy. A P P E N D I X 142 For an executable, the required form of the "work that uses the library" must include any data and utility programs need-

ed for reproducing the executable from it. However, as a spe-

cial exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the exe-

cutable. It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normal-

ly accompany the operating system. Such a contradiction means you cannot use both them and the library together in an executable that you distribute. 7. You may place library facilities that are a work based on the library side-by-side in a single library together with other library facilities not covered by this license, and distribute such a combined library, provided that the separate distribu-

tion of the work based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things:

a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the sections above. b) Give prominent notice with the combined library of the fact that part of it is a work based on the library, and explaining where to find the accompanying uncombined form of the same work. 8. You may not copy, modify, sublicense, link with, or distribute the library except as expressly provided under this license. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the library is void, and will automatically termi-

nate your rights under this license. However, parties who have received copies, or rights, from you under this license will not have their licenses terminated so long as such parties remain in full compliance. 9. You are not required to accept this license, since you have not signed it. However, nothing else grants you permission to mod-

ify or distribute the library or its derivative works. These actions are prohibited by law if you do not accept this license. Therefore, by modifying or distributing the library (or any work based on the library), you indicate your acceptance of this license to do so, and all its terms and conditions for copying, distributing or modifying the library or works based on it. 10.Each time you redistribute the library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or mod-

ify the library subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this license. 11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the con-

ditions of this license, they do not excuse you from the con-

ditions of this license. If you cannot distribute so as to satis-

fy simultaneously your obligations under this license and any other pertinent obligations, then as a consequence you may not distribute the library at all. For example, if a patent license would not permit royalty-free redistribution of the library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this license would be to refrain entirely from distribution of the library. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest valid-

ity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution sys-

tem which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a license cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this license. 12.If the distribution and/or use of the library is restricted in cer-

tain countries either by patents or by copyrighted interfaces, the original copyright holder who places the library under this license may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this license incorporates the limitation as if written in the body of this license. 13.The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the library specifies a version number of this license which applies to it and any later version, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. A P P E N D I X 143 To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the copyright line and a pointer to where the full notice is found. one line to give the library's name and a brief idea of what it does. Copyright (C) <year> <name of author>

This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2.1 of the license, or (at your option) any later version. This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-

POSE. See the GNU Lesser General Public License for more details. You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Also add information on how to contact you by electronic and paper mail. You should also get your employer (if you work as a programmer) or your school, if any, to sign a copyright disclaimer for the library, if necessary. Here is a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the library Frob (a library for tweaking knobs) written by James Random Hacker. signature of Ty Coon, 1 April 1990 Ty Coon, President of Vice APPENDIX If the library does not specify a license version number, you may choose any version ever published by the Free Software Foundation. 14.If you wish to incorporate parts of the library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make excep-

tions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY 15.BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLD-

ERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 16.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUS-

TAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. END OF TERMS AND CONDITIONS How to apply these terms to your new libraries If you develop a new library, and you want it to be of the great-

est possible use to the public, we recommend making it free soft-

ware that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License). A P P E N D I X 144 MOZILLA PUBLIC LICENSE Version 1.1

1.Definitions. 1.0.1. Commercial use means distribution or otherwise making the covered code available to a third party. 1.1. Contributor means each entity that creates or con-

tributes to the creation of modifications. 1.2. 1.3. 1.4. Contributor version means the combination of the orig-

inal code, prior modifications used by a contributor, and the modifications made by that particular contributor. Covered code means the original code or modifications or the combination of the original code and modifications, in each case including portions thereof. Electronic distribution mechanism means a mechanism generally accepted in the software development communi-

ty for the electronic transfer of data. 1.5. Executable means covered code in any form other than source code. 1.6. 1.7. Initial developer means the individual or entity identified as the initial Developer in the Source Code notice required by exhibit A. Larger work means a work which combines covered code or portions thereof with code not governed by the terms of this License. 1.8. License means this document. 1.8.1. Licensable means having the right to grant, to the maxi-

mum extent possible, whether at the time of the initial grant or subsequently acquired, any and all of the rights conveyed herein. 1.9. Modifications means any addition to or deletion from the substance or structure of either the original code or any previous modifications. When covered code is released as a series of files, a modification is:

A. Any addition to or deletion from the contents of a file containing original code or previous modifications. B. Any new file that contains any part of the original code or previous modifications. 1.10. Original code means source code of computer software code which is described in the source code notice required by exhibit as original code, and which, at the time of its release under this license is not already covered code governed by this license. 1.10.1.Patent claims means any patent claim(s), now owned or hereafter acquired, including without limitation, method, process, and apparatus claims, in any patent licensable by grantor. 1.11. Source code means the preferred form of the covered code for making modifications to it, including all modules it contains, plus any associated interface definition files, scripts used to control compilation and installation of an executable, or source code differential comparisons against either the original code or another well known, available covered code of the contributor's choice. The source code can be in a compressed or archival form, pro-

vided the appropriate decompression or de-archiving soft-

ware is widely available for no charge. 1.12. You (or Your) means an individual or a legal entity exercising rights under, and complying with all of the terms of, this license or a future version of this license issued under section 6.1. For legal entities, You includes any entity which controls, is controlled by, or is under common control with You. For purposes of this definition, control means (a) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (b) own-

ership of more than fifty percent (50%) of the outstand-

ing shares or beneficial ownership of such entity. 2. Source Code License. 2.1. The initial developer grant. The initial developer hereby grants You a world-wide, roy-

alty-free, non-exclusive license, subject to third party intel-

lectual property claims:

a) under intellectual property rights (other than patent or trademark) licensable by initial developer to use, repro-

duce, modify, display, perform, sublicense and distrib-

ute the original code (or portions thereof) with or with-

out modifications, and/or as part of a larger work; and

(b) under patents claims infringed by the making, using or selling of original code, to make, have made, use, prac-

tice, sell, and offer for sale, and/or otherwise dispose of the original code (or portions there of). A P P E N D I X 145 APPENDIX

(c) the licenses granted in this section 2.1(a) and (b) are effective on the date Initial developer first distributes original code under the terms of this license.

(d) Notwithstanding section 2.1(b) above, no patent license is granted: 1) for code that You delete from the original Code; 2) separate from the original code; or 3) for infringements caused by: i) the modification of the original code or ii) the combination of the original code with other software or devices. 2.2. Contributor Grant. Subject to third party intellectual property claims, each contributor hereby grants You a world-wide, royalty-free, non-exclusive license

(a) under intellectual property rights (other than patent or trademark) licensable by contributor, to use, reproduce, modify, display, perform, sublicense and distribute the modifications created by such contribu-

tor (or portions thereof) either on an unmodified basis, with other modifications, as covered code and/or as part of a larger work; and

(b) under patent claims infringed by the making, using, or selling of modifications made by that contributor either alone and/or in combination with its contributor version (or portions of such combination), to make, use, sell, offer for sale, have made, and/or otherwise dispose of: 1) modifications made by that contributor

(or portions thereof); and 2) the combination of mod-

ifications made by that contributor with its contributor version (or portions of such combination).

(c) the licenses granted in sections 2.2(a) and 2.2(b) are effective on the date contributor first makes commer-

cial use of the covered code.

(d) Notwithstanding section 2.2(b) above, no patent license is granted: 1) for any code that contributor has deleted from the contributor version; 2) separate from the contributor version; 3) for infringements caused by: i) third party modifications of contributor version or ii) the combination of modifications made by that contributor with other software (except as part of the contributor version) or other devices; or 4) under patent claims infringed by covered code in the absence of modifications made by that contributor. 3. Distribution Obligations. 3.1. Application of license. The modifications which You create or to which you con-

tribute are governed by the terms of this license, including without limitation section 2.2. The source code version of covered code may be distributed only under the terms of this license or a future version of this license released under section 6.1, and you must include a copy of this license with every copy of the source code you distribute. You may not offer or impose any terms on any source code version that alters or restricts the applicable version of this license or the recipients' rights hereunder. However, you may include an additional document offering the additional rights described in section 3.5. 3.2. Availability of source code. Any modification which you create or to which you con-

tribute must be made available in source code form under the terms of this license either on the same media as an executable version or via an accepted electronic distribu-

tion mechanism to anyone to whom you made an exe-

cutable version available; and if made available via elec-

tronic distribution mechanism, must remain available for at least twelve (12) months after the date it initially became available, or at least six (6) months after a subsequent version of that particular modification has been made available to such recipients. You are responsible for ensur-

ing that the source code version remains available even if the electronic distribution mechanism is maintained by a third party. 3.3. Description of modifications. 3.4. You must cause all covered code to which you contribute to contain a file documenting the changes You made to create that covered code and the date of any change. You must include a prominent statement that the modification is derived, directly or indirectly, from original code provided by the initial developer and including the name of the initial developer in (a) the source code, and (b) in any notice in an executable version or related documentation in which you describe the origin or ownership of the covered code. Intellectual property matters

(a) Third party claims. If contributor has knowledge that a license under a third party's intellectual property rights is required to exercise the rights granted by such contributor under sections 2.1 or 2.2, contributor must include a text file with the source code distribution titled "LEGAL" which describes the claim and the party making the claim in sufficient detail that a recipient will know whom to contact. If contributor obtains such knowledge after the modification is made available as described in section 3.2, contributor shall promptly modi-

fy the LEGAL file in all copies contributor makes available thereafter and shall take other steps (such as notifying appropriate mailing lists or newsgroups) reasonably calcu-

lated to inform those who received the covered code that new knowledge has been obtained.

(b) Contributor APIs. If contributor's modifications include an application programming interface and contributor has knowledge of patent licenses which are reasonably necessary to implement that API, contributor must also include this information in the LEGAL file. A P P E N D I X 146

(c) Representations. contributor represents that, except as disclosed pursuant to section 3.4(a) above, contributor believes that contributor's modifications are contributor's original creation(s) and/or contributor has sufficient rights to grant the rights conveyed by this license. 3.7. Larger works. You may create a larger work by combining covered code with other code not governed by the terms of this license and distribute the larger work as a single product. In such a case, you must make sure the requirements of this license are fulfilled for the covered code. 3.5. Required notices. 4. Inability to comply due to statute or regulation. You must duplicate the notice in exhibit A in each file of the source code. If it is not possible to put such notice in a particular source code file due to its structure, then You must include such notice in a location (such as a relevant directory) where a user would be likely to look for such a notice. If You created one or more modification(s), you may add your name as a contributor to the notice described in exhibit A. you must also duplicate this license in any documentation for the source code where You describe recipients' rights or ownership rights relating to covered code. You may choose to offer, and to charge a fee for, warranty, support, indemnity or liability obligations to one or more recipients of covered code. However, you may do so only on your own behalf, and not on behalf of the Initial developer or any contributor. You must make it absolutely clear than any such warranty, support, indemni-

ty or liability obligation is offered by you alone, and You hereby agree to indemnify the Initial developer and every contributor for any liability incurred by the Initial develop-

er or such contributor as a result of warranty, support, indemnity or liability terms you offer. 3.6. Distribution of executable versions. You may distribute covered code in executable form only if the requirements of section 3.1-3.5 have been met for that covered code, and if you include a notice stating that the source code version of the covered code is available under the terms of this license, including a description of how and where you have fulfilled the obligations of section 3.2. The notice must be conspicuously included in any notice in an executable version, related documentation or collateral in which you describe recipients' rights relating to the covered code. You may distribute the executable version of covered code or ownership rights under a license of your choice, which may contain terms different from this license, provided that you are in compliance with the terms of this license and that the license for the exe-

cutable version does not attempt to limit or alter the recip-

ient's rights in the source code version from the rights set forth in this license. If you distribute the executable ver-

sion under a different license you must make it absolutely clear that any terms which differ from this license are offered by you alone, not by the Initial developer or any contributor. You hereby agree to indemnify the initial developer and every contributor for any liability incurred by the initial developer or such contributor as a result of any such terms You offer. If it is impossible for you to comply with any of the terms of this license with respect to some or all of the covered code due to statute, judicial order, or regulation then you must: (a) comply with the terms of this license to the max-

imum extent possible; and (b) describe the limitations and the code they affect. Such description must be included in the LEGAL file described in section 3.4 and must be included with all distributions of the source code. Except to the extent prohibited by statute or regulation, such description must be sufficiently detailed for a recipient of ordinary skill to be able to understand it. 5. Application of this license. This license applies to code to which the initial developer has attached the notice in exhibit A and to related covered code. 6. Versions of the license. 6.1. New versions. Netscape communications corporation (Netscape) may publish revised and/or new versions of the license from time to time. Each version will be given a distinguishing version number. 6.2. Effect of new versions. Once covered code has been published under a particular version of the license, you may always continue to use it under the terms of that version. You may also choose to use such covered code under the terms of any subsequent version of the license published by netscape. No one other than netscape has the right to modify the terms applicable to covered code created under this license. A P P E N D I X 6.3. Derivative works. If You create or use a modified version of this license

(which you may only do in order to apply it to code which is not already covered code governed by this license), You must (a) rename Your license so that the phrases

"Mozilla", "MOZILLAPL", "MOZPL", "Netscape", "MPL",

"NPL" or any confusingly similar phrase do not appear in your license (except to note that your license differs from this license) and (b) otherwise make it clear that Your version of the license contains terms which differ from the Mozilla Public license and netscape Public License. (Filling in the name of the initial developer, original code or con-

tributor in the notice described in exhibit A shall not of themselves be deemed to be modifications of this license.) 147 APPENDIX 7. DISCLAIMER OF WARRANTY. COVERED CODE IS PROVIDED UNDER THIS LICENSE ON AN AS IS BASIS, WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, WARRANTIES THAT THE COV-

ERED CODE IS FREE OF DEFECTS, MERCHANTABLE, FIT FOR A PARTICULAR PURPOSE OR NON-INFRINGING. THE ENTIRE RISK AS TO THE QUALITY AND PERFOR-

MANCE OF THE COVERED CODE IS WITH YOU. SHOULD ANY COVERED CODE PROVE DEFECTIVE IN ANY RESPECT, YOU (NOT THE INITIAL DEVELOPER OR ANY OTHER CONTRIBUTOR) ASSUME THE COST OF ANY NECESSARY SERVICING, REPAIR OR CORRECTION. THIS DISCLAIMER OF WARRANTY CONSTITUTES AN ESSENTIAL PART OF THIS LICENSE. NO USE OF ANY COVERED CODE IS AUTHORIZED HEREUNDER EXCEPT UNDER THIS DISCLAIMER. 8. TERMINATION. 8.1. This license and the rights granted hereunder will terminate automatically if you fail to comply with terms herein and fail to cure such breach within 30 days of becoming aware of the breach. All sublicenses to the covered code which are properly granted shall survive any termination of this license. Provisions which, by their nature, must remain in effect beyond the termination of this license shall survive. 8.2. If you initiate litigation by asserting a patent infringement claim (excluding declatory judgment actions) against ini-

tial developer or a contributor (the initial developer or contributor against whom you file such action is referred to as Participant) alleging that:

(a) such participant's contributor version directly or indi-

rectly infringes any patent, then any and all rights granted by such participant to you under sections 2.1 and/or 2.2 of this license shall, upon 60 days notice from Participant terminate prospectively, unless if within 60 days after receipt of notice you either: (i) agree in writing to pay participant a mutually agreeable reasonable royalty for your past and future use of modifications made by such participant, or (ii) withdraw your litigation claim with respect to the contributor version against such participant. If within 60 days of notice, a reasonable royalty and payment arrangement are not mutually agreed upon in writing by the parties or the litigation claim is not withdrawn, the rights granted by partici-

pant to you under sections 2.1 and/or 2.2 automati-

cally terminate at the expiration of the 60 day notice period specified above.

(b) any software, hardware, or device, other than such par-

ticipant's contributor Version, directly or indirectly infringes any patent, then any rights granted to You by such participant under sections 2.1(b) and 2.2(b) are revoked effective as of the date you first made, used, sold, distributed, or had made, modifications made by that participant. 8.3. If you assert a patent infringement claim against partici-

pant alleging that such participant's contributor version directly or indirectly infringes any patent where such claim is resolved (such as by license or settlement) prior to the initiation of patent infringement litigation, then the rea-

sonable value of the licenses granted by such participant under sections 2.1 or 2.2 shall be taken into account in determining the amount or value of any payment or license. 8.4. In the event of termination under sections 8.1 or 8.2 above, all end user license agreements (excluding distributors and resellers) which have been validly granted by you or any distributor hereunder prior to termination shall survive termination. 9. LIMITATION OF LIABILITY. UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL THEORY, WHETHER TORT (INCLUDING NEGLIGENCE), CONTRACT, OR OTHERWISE, SHALL YOU, THE INITIAL DEVELOPER, ANY OTHER CONTRIBUTOR, OR ANY DIS-

TRIBUTOR OF COVERED CODE,OR ANY SUPPLIER OF ANY OF SUCH PARTIES, BE LIABLE TO ANY PERSON FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUEN-

TIAL DAMAGES OF ANY CHARACTER INCLUDING, WITH-

OUT LIMITATION, DAMAGES FOR LOSS OF GOODWILL, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNC-

TION, OR ANY AND ALL OTHER COMMERCIAL DAM-

AGES OR LOSSES, EVEN IF SUCH PARTY SHALL HAVE BEEN INFORMED OF THE POSSIBILITY OF SUCH DAM-

AGES. THIS LIMITATION OF LIABILITY SHALL NOT APPLY TO LIABILITY FOR DEATH OR PERSONAL INJURY RESULT-

ING FROM SUCH PARTY'S NEGLIGENCE TO THE EXTENT APPLICABLE LAW PROHIBITS SUCH LIMITATION. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAM-

AGES, SO THIS EXCLUSION AND LIMITATION MAY NOT APPLY TO YOU. 10. U.S. GOVERNMENT END USERS. The covered code is a "commercial item," as that term is defined in 48 C.F.R. 2.101 (Oct. 1995), consisting of

"commercial computer software" and "commercial computer software documentation," as such terms are used in 48 C.F.R. 12.212 (Sept. 1995). Consistent with 48 C.F.R. 12.212 and 48 C.F.R. 227.7202-1 through 227.7202-4

(June 1995), all U.S. Government end users acquire cov-

ered code with only those rights set forth herein. A P P E N D I X 148 11. MISCELLANEOUS. EXHIBIT A -Mozilla Public License. This license represents the complete agreement concerning subject matter hereof. If any provision of this license is held to be unenforceable, such provision shall be reformed only to the extent necessary to make it enforceable. This License shall be governed by California law provisions

(except to the extent applicable law, if any, provides oth-

erwise), excluding its conflict-of-law provisions. With respect to disputes in which at least one party is a citizen of, or an entity chartered or registered to do business in the united states of america, any litigation relating to this License shall be subject to the jurisdiction of the federal courts of the northern district of california, with venue lying in santa clara county, california, with the losing party responsible for costs, including without limitation, court costs and reasonable attorneys' fees and expenses. The application of the united nations convention on contracts for the International sale of goods is expressly excluded. Any law or regulation which provides that the language of a contract shall be construed against the drafter shall not apply to this license. 12. RESPONSIBILITY FOR CLAIMS. As between initial developer and the contributors, each party is responsible for claims and damages arising, directly or indirectly, out of its utilization of rights under this license and you agree to work with initial developer and contributors to distribute such responsibility on an equitable basis. Nothing herein is intended or shall be deemed to constitute any admission of liability. 13. MULTIPLE-LICENSED CODE. Initial developer may designate portions of the covered code as "Multiple-Licensed". "Multiple-Licensed" means that the initial developer permits you to utilize portions of the covered code under your choice of the NPL or the alternative licenses, if any, specified by the initial developer in the file described in exhibit A. The contents of this file are subject to the Mozilla Public License Version 1.1 (the license); you may not use this file except in compliance with the License. You may obtain a copy of the license at http://www.mozilla.org/MPL/

Software distributed under the license is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See the license for the specific language governing rights and limitations under the License. The Original Code is ______________________________________. Initial Developer The is___________________. Portions created by ______________________ are Copyright (C) _______________________. All Rights Reserved. the Original Code of Contributor(s): ______________________________________. Alternatively, the contents of this file may be used under the terms of the _____ license (the "[___] License"), in which case the provisions of [______] license are applicable instead of those above. If you wish to allow use of your version of this file only under the terms of the [____] license and not to allow others to use your version of this file under the MPL, indicate your decision by deleting the provisions above and replace them with the notice and other provisions required by the [___] license. If you do not delete the provisions above, a recipient may use your version of this file under either the MPL or the [___] license."

NOTE: The text of this exhibit A may differ slightly from the text of the notices in the source code files of the original code. You should use the text of this exhibit A rather than the text found in the original code/source code for Your modifications. A P P E N D I X 149