User Manual PRODUCT NAME : RF Module MODEL NAME : LGSBW51 The information contained herein is the exclusive property of LG Innotek and shall not be distributed, reproduced or disclosed in whole or no in part without prior written permission of LG Innotek.
(00)-0073 REG. DATE : 2014.09.24 REV. DATE : 2014.09.24 User Manual MODEL NAME: TWCM-B201D(LGIT) LGSBW51(LGE) REV.NO : v0.01 PAGE :
1 / 9 DOCUMENT No :
Index Features Picture of Product Installation Manual Block Diagram Absolute Maximum Ratings No Description 1 2 3 4 5 6 Operating Conditions 7 8 9 Out Drawing 10 Packing Information Standard Test Conditions Pin Description Page 2 2 3 4 4 5 5 6 7 8 Copyright. 2014. All Rights Reserved. REG. DATE : 2014.09.24 REV. DATE : 2014.09.24 User Manual MODEL NAME: TWCM-B201D(LGIT) LGSBW51(LGE) REV.NO : v0.01 PAGE :
2 / 9 DOCUMENT No :
1. Features TWCM-B201D is the small size and low power module for IEEE 802.11ac wireless LAN
& BT4.0 + HS. TWCM-B201D is based on Broadcom BCM43569 solution. IEEE 802.11 a/b/g/n/ac Dual Band WLAN infrastructure Bluetooth 4.0 + HS Size : 68.0mm x 38.0mm Two stream spatial multiplexing up to 300Mbps(802.11n)/ 867Mbps(802.11ac) WLAN Metal Press antenna, BT Printed antenna on Use on-chip OTP (One-Time Programmable) Host Interface : USB2.0 (WLAN & BT)
- This model is using the common USB2.0 to control WLAN and BT Security : WAPI, WEP, WPA, WPA2, WMM, AES, WEP, TKIP, CKP Application: DTV, DVR, HD DVD Player, Blue-ray Disk Player, STB 2. Picture of Product Copyright. 2014. All Rights Reserved. REG. DATE : 2014.09.24 REV. DATE : 2014.09.24 User Manual MODEL NAME: TWCM-B201D(LGIT) LGSBW51(LGE) REV.NO : v0.01 PAGE :
3 / 9 DOCUMENT No :
3. Installation Manual Install the module like below in the back of the TV TWCM-B201D installed position Copyright. 2014. All Rights Reserved. REG. DATE : 2014.09.24 REV. DATE : 2014.09.24 User Manual MODEL NAME: TWCM-B201D(LGIT) LGSBW51(LGE) REV.NO : v0.01 PAGE :
4 / 9 DOCUMENT No :
4. Block Diagram ANT1 ANT0 r e x e p D i l r e x e p D i l BT ANT 5G SPDT 2G SPDT 5G SPDT 2G SPDT LPF BCM43569 802.11ac MAC Security OTP USB Hub Clock_(24MHz) I n t e r n a l B u s WLAN USB 2.0 BT USB 2.0 GPIO B U H B S U r o t c e n n o C 2 x 2 Radio 802.11ac PHY Serial Flash (1M) 3.3V Main Clock(40MHz) 5. Absolute Maximum Ratings Caution : The specifications in Table 1 define levels at which permanent damage to the device can occur. Function operation is not guaranteed under these conditions. Operating at absolute maximum conditions for extend periods can adversely affect the long-term reliability of the device. Parameter Storage Temperature Storage Humidity (40) Min
-20
Max
+80 90 Unit
. Other conditions 1) Do not use or store modules in the corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are contained. Also, avoid exposure to moisture. 2) Store the modules where the temperature and relative humidity do not exceed 5 to 40 and 20 to 60%. 3) Assemble the modules within 6 months. Check the soldering ability in case of 6 months over. Copyright. 2014. All Rights Reserved. REG. DATE : 2014.09.24 REV. DATE : 2014.09.24 User Manual MODEL NAME: TWCM-B201D(LGIT) LGSBW51(LGE) REV.NO : v0.01 PAGE :
5 / 9 DOCUMENT No :
6. Operating Conditions Parameter Ambient Temperature Ambient Humidity (40) Supply Voltage Min 0
4.75 Typ
5.0 Max 60 85 5.25 Unit
Vdc 7. Standard Test Conditions The Test for electrical specification shall be performed under the following condition Otherwise this following conditions, not guaranteed this performance. 7-1. Ambient condition Temparature Humidity 7-2. Power supply voltages Input Voltage VDD_3.3V 25 5 65 5%
Supply Voltage
+3.3V 0.165V Copyright. 2014. All Rights Reserved. REG. DATE : 2014.09.24 REV. DATE : 2014.09.24 User Manual MODEL NAME: TWCM-B201D(LGIT) LGSBW51(LGE) REV.NO : v0.01 PAGE :
6 / 9 DOCUMENT No :
8. Pin Description Pin No. Pin Name 1 2 3 4 5 6 7 8 VCC WLAN USB D-
WLAN USB D+
GND WLAN_WAKE_HOST GND BT_WAKE_HOST GND I/O I I/O I/O
O
O
Pin Description
+3.3V USB Communication signal USB_DN USB Communication signal USB_DP Ground WLAN wake-up signal Ground Bluetooth wake-up signal Ground Copyright. 2014. All Rights Reserved. REG. DATE : 2014.09.24 REV. DATE : 2014.09.24 User Manual MODEL NAME: TWCM-B201D(LGIT) LGSBW51(LGE) REV.NO : v0.01 PAGE :
7 / 9 DOCUMENT No :
9. Outline Drawing Copyright. 2014. All Rights Reserved. DOCUMENT No :
REG. DATE : 2014.09.24 REV. DATE : 2014.09.24 User Manual MODEL NAME: TWCM-B201D(LGIT) LGSBW51(LGE) REV.NO : v0.01 PAGE :
8 / 9 10. Packing Information Copyright. 2014. All Rights Reserved. REG. DATE : 2014.09.24 REV. DATE : 2014.09.24 User Manual MODEL NAME: TWCM-B201D(LGIT) LGSBW51(LGE) REV.NO : v0.01 PAGE :
9 / 9 DOCUMENT No :
Copyright. 2014. All Rights Reserved. Regulatory Notices 1. FCC FCC Statements:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. End Product Labeling The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification Number are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following:
Contains FCC ID: Contains IC: The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product. OEM Responsibilities to comply with FCC and Industry Canada Regulations The module has been certified for integration into products only by OEM integrators under the following condition:
- The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times.
- The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. As long as the two condition above is met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cant be met (for certain configurations or co-location with another transmitter), then the FCC and Industry Canada authorizations are no longer considered valid and the FCC ID and IC Certification Number cant be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC and Industry Canada authorization. FCC Part 15.105 statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. 2. IC tiquetage du produit final (IC) Le module BT111 est tiquet avec sa propre identification FCC et son propre numro de certification IC. Si lidentification FCC et le numro de certification IC ne sont pas visibles lorsque le module est install lintrieur dun autre dispositif, la partie externe du dispositif dans lequel le module est install devra galement prsenter une tiquette faisant rfrence au module inclus. Dans ce cas, le produit final devra tre tiquet sur une zone visible avec les informations suivantes :
Contient module metteur identification FCC ID: Contient module metteur IC : Dans le guide dutilisation du produit final, lintgrateur OEM doit sabstenir de fournir des informations lutilisateur final portant sur les procdures suivre pour installer ou retirer ce module RF ou pour changer les paramtres RF. Responsabilits des OEM quant la conformit avec les rglementations de FCC et d Industrie Canada Les modules ont t certifis pour entrer dans la fabrication de produits exclusivement raliss par des intgrateurs dans les conditions suivantes :
- Lantenne (ou les antennes) doit tre installe de faon maintenir tout instant une distance minimum de au moins 20 cm entre la source de radiation (lantenne) et toute personne physique.
- Le module transmetteur ne doit pas tre install ou utilis en concomitance avec une autre antenne ou un autre transmetteur. Tant que ces deux conditions sont runies, il nest pas ncessaire de procder des tests supplmentaires sur le transmetteur. Cependant, lintgrateur est responsable des tests effectus sur le produit final afin de se mettre en conformit avec dventuelles exigences complmentaires lorsque le module est install (exemple : missions provenant dappareils numriques, exigences vis--vis de priphriques informatiques, etc.) REMARQUE IMPORTANTE : En cas dinobservance de ces conditions (en ce qui concerne certaines configurations ou lemplacement du dispositif proximit dun autre metteur), les autorisations de FCC et dIndustrie Canada ne seront plus considres valables et lidentification de FCC et le numro de certification dIC ne pourront pas tre utiliss sur le produit final. Dans ces cas, lintgrateur OEM sera charg dvaluer nouveau le produit final (y compris lmetteur) et dobtenir une autorisation indpendante de FCC et dIndustrie Canada. IC warning This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions : (1) this device may not cause interference, and
(2) this device musrt accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate thisequipment.Attention:
Les changements ou modifications de cet appareil non expressment approuv par le fabricant peuvent annuler votre droit utiliser cet quipement.