User Manual PRODUCT NAME : 802.11a/b/g/n/ac MODEL NAME : LGSWFAC71 The information contained herein is the exclusive property of LG Innotek and shall not be distributed, reproduced or disclosed in whole or no in part without prior written permission of LG Innotek.
(00)-0073 REG. DATE : 2016.09.02 REV. DATE : 2016.09.02 User Manual MODEL NAME: TWFM-K008D(LGIT) LGSWFAC71(LGE) REV.NO : v0.01 PAGE :
1 / 9 DOCUMENT No :
-
Index No Description 1 2 3 4 5 Features Picture of Product Installation Manual Block Diagram Absolute Maximum Ratings 6 Operating Conditions 7 8 Standard Test Conditions Pin Description 9 Out Drawing 10 Packing Information Page 2 2 3 4 4 5 5 6 7 8 Copyright. 2016. All Rights Reserved. REG. DATE : 2016.09.02 REV. DATE : 2016.09.02 User Manual MODEL NAME: TWFM-K008D(LGIT) LGSWFAC71(LGE) REV.NO : v0.01 PAGE :
2 / 9 DOCUMENT No :
-
1. Features LGSWFAC71 is the small size and low power module for IEEE 802.11ac wireless LAN. TWFM-K008D is based on MTK MT7612U solution. IEEE 802.11 a/b/g/n/ac Dual Band WLAN infrastructure Size : 48.0mm x 30.0mm Two stream spatial multiplexing up to 300Mbps(802.11n)/ 867Mbps(802.11ac) WLAN Metal Press antenna Use on-chip OTP (One-Time Programmable) Host Interface : USB2.0 Security : WAPI, WEP, WPA, WPA2, WMM, AES, WEP, TKIP, CKP Application: DTV, DVR, HD DVD Player, Blue-ray Disk Player, STB This device is restricted to indoor use only within the 5.15 ~ 5.25 GHz Band. 2. Picture of Product Copyright. 2016. All Rights Reserved. REG. DATE : 2016.09.02 REV. DATE : 2016.09.02 User Manual MODEL NAME: TWFM-K008D(LGIT) LGSWFAC71(LGE) REV.NO : v0.01 PAGE :
3 / 9 DOCUMENT No :
-
3. Installation Manual Install the module like below in the back of the TV LGSWFAC71 installed position Copyright. 2016. All Rights Reserved. Cable REG. DATE : 2016.09.02 REV. DATE : 2016.09.02 User Manual MODEL NAME: TWFM-K008D(LGIT) LGSWFAC71(LGE) REV.NO : v0.01 PAGE :
4 / 9 DOCUMENT No :
-
4. Block Diagram ANT0 ANT1 Diplexer Diplexer MT7612U 2.4GHz 5GHz 2.4GHz 5GHz 11ac 2T2R Baseband 32bit RISC CPU MAC /
Packet buffer/
Security engine 40MHz Main Clock System Control USB2.0 Interface PMU 3.3V R O T C E N N O C N I P 8 F
/
I B S U 5. Absolute Maximum Ratings Caution : The specifications in Table 1 define levels at which permanent damage to the device can occur. Function operation is not guaranteed under these conditions. Operating at absolute maximum conditions for extend periods can adversely affect the long-term reliability of the device. Parameter Storage Temperature Storage Humidity (40) Min
-20
-
Max
+80 90 Unit
%
. Other conditions 1) Do not use or store modules in the corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are contained. Also, avoid exposure to moisture. 2) Store the modules where the temperature and relative humidity do not exceed 5 to 40 and 20 to 60%. 3) Assemble the modules within 6 months. Check the soldering ability in case of 6 months over. Copyright. 2016. All Rights Reserved. REG. DATE : 2016.09.02 REV. DATE : 2016.09.02 User Manual MODEL NAME: TWFM-K008D(LGIT) LGSWFAC71(LGE) REV.NO : v0.01 PAGE :
5 / 9 DOCUMENT No :
-
6. Operating Conditions Parameter Min Typ Max Ambient Temperature Ambient Humidity (40) 0
-
-
-
Supply Voltage 3.135 3.3 60 85 3.6 Unit
%
Vdc 7. Standard Test Conditions The Test for electrical specification shall be performed under the following condition Otherwise this following conditions, not guaranteed this performance. 7-1. Ambient condition Temparature Humidity 7-2. Power supply voltages 25 5 65 5%
Input Voltage VDD_3.3V Supply Voltage
+3.3V 0.165V Copyright. 2016. All Rights Reserved. REG. DATE : 2016.09.02 REV. DATE : 2016.09.02 User Manual MODEL NAME: TWFM-K008D(LGIT) LGSWFAC71(LGE) REV.NO : v0.01 PAGE :
6 / 9 DOCUMENT No :
-
8. Pin Description Pin No. Pin Name 1 2 3 4 5 6 7 8 VCC USB D-
USB D+
GND WL_HOST_WAKE VCC N.C GND I/O I I/O I/O I O I
-
I Pin Description Power Supply 3.3V USB Communication signal USB D-
USB Communication signal USB D+
Ground Wake On WLAN Power Supply 3.3V Not connected Ground Copyright. 2016. All Rights Reserved. REG. DATE : 2016.09.02 REV. DATE : 2016.09.02 User Manual MODEL NAME: TWFM-K008D(LGIT) LGSWFAC71(LGE) REV.NO : v0.01 PAGE :
7 / 9 DOCUMENT No :
-
9. Outline Drawing Copyright. 2016. All Rights Reserved.
'16. 07. 12'16. 07. 12Changsung Kim.Ilhee Park.Jangeun Yang.'16. 07. 12 REG. DATE : 2016.09.02 REV. DATE : 2016.09.02 User Manual MODEL NAME: TWFM-K008D(LGIT) LGSWFAC71(LGE) REV.NO : v0.01 PAGE :
8 / 9 DOCUMENT No :
-
10. Packing Information 10-1. Inner Box packing 1 Tray Package Qty : 120EA Tray Material : Antistatic PET or Antistatic PS 1 Tray Weight : 0.2kg
(1 Module Weight : 6.4 0.5g) Total Packing Qty : 1,440EA Total Packing Weight : 12.6 0.8kg Tray Tray Stacking Qty :6 Stack(Zigzag stack) Corrugated Fibreboard PP Band RoHS Marking Barcode Label RoHS Marking :
Label, Stamp, Printing Marking Color :
Gray or Red for Stamp, Label, Printing on the board and etc. Black only for Printing on Label. 1 Box Package Qty : 720EA Box Size : A x B x C (512 x 377 x 121.5) Box Material : Corrugated Fibreboards 1 Box Packing Weight : 6.3 0.4kg Inner Box Copyright. 2016. All Rights Reserved. REG. DATE : 2016.09.02 REV. DATE : 2016.09.02 User Manual MODEL NAME: TWFM-K008D(LGIT) LGSWFAC71(LGE) REV.NO : v0.01 PAGE :
9 / 9 DOCUMENT No :
-
10-2. Carton Box Packing Copyright. 2016. All Rights Reserved. DOCUMENT No :
-
User Manual MODEL NAME: TWFM-K008D(LGIT) LGSWFAC71(LGE) REV.NO : v0.01 PAGE :
10 / 9 REG. DATE : 2016.09.02 REV. DATE : 2016.09.02 Regulatory Notices 1. FCC FCC Part 15.19 Statements:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Part 15.21 statement Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. FCC Part 15.105 statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. OEM Responsibilities to comply with FCC and Industry Canada Regulations The module has been certified for integration into products only by OEM integrators under the following condition:
- The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times.
- The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. As long as the two condition above is met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). End Product Labeling The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification Number are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following:
Contains FCC ID: BEJLGSBWAC71 Contains IC: 2703H-LGSBWAC71 Copyright. 2016. All Rights Reserved. DOCUMENT No :
-
User Manual MODEL NAME: TWFM-K008D(LGIT) LGSWFAC71(LGE) REV.NO : v0.01 PAGE :
11 / 9 REG. DATE : 2016.09.02 REV. DATE : 2016.09.02 2. IC RSS-GEN, Sec. 7.1.3 (licence-exempt radio apparatus) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. RF Exposure The antenna (or antennas) must be installed so as to maintain at all times a distance minimum of at least 20 cm between the radiation source (antenna) and any individual. This device may not be installed or used in conjunction with any other antenna or transmitter. l'exposition aux RF Lantenne (ou les antennes) doit tre installe de faon maintenir tout instant une distance minimum de au moins 20 cm entre la source de radiation (lantenne) et toute personne physique. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate thisequipment.Attention:
Les changements ou modifications de cet appareil non expressment approuv par le fabricant peuvent annuler votre droit utiliser cet quipement. tiquetage du produit final (IC) Le module BT111 est tiquet avec sa propre identification FCC et son propre numro de certification IC. Si lidentification FCC et le numro de certification IC ne sont pas visibles lorsque le module est install lintrieur dun autre dispositif, la partie externe du dispositif dans lequel le module est install devra galement prsenter une tiquette faisant rfrence au module inclus. Dans ce cas, le produit final devra tre tiquet sur une zone visible avec les informations suivantes :
Contient module metteur identification FCC ID : BEJLGSWFAC71 Contient module metteur IC : 2703H-LGSWFAC71 3. CE Hereby, ' LG Electronics USA, Inc.' declares that this LGSWFAC71 is in compliance with the essential requirements and other relevant provisions of directive 1999/5/EC. This device is restricted to indoor use only within the 5.15 ~ 5.25GHz Band. Copyright. 2016. All Rights Reserved.