FCC ID: BEJGEN11NAN Telematics

LG Electronics Inc. 1 17-8-8 Technical Description Descriptive Information The RF platform of GEN11 supports highly integrated LTE/UMTS/GSM-transceiver, with all necessary features to enable multi mode, multi band car telematics applications. It incorporates a fully integrated dual mode receiver, multi band TX outputs, TCVCXO control, a measurement interface, Qualcomm(Transceiver / Modem) compliant high speed data and control interface, a multi mode timer unit and all necessary front end signals for the complete RF Engine control. Overall the GEN11 directly supports RF engines with up to GSM bands, WCDMA bands and LTE bands. 1. RF Transceiver (WTR3925) Multimode operation (See modem IC documents for specific capabilities)

- 3GPP GSM, GPRS, and EDGE (WTR3925/WTR3905 only)

-

-

-

3GPP WCDMA Rel 99, HSDPA, HSUPA, HSPA+

3GPP LTE FDD and TDD, with carrier aggregation (WTR3925 only) TD-SCDMA LTE carrier aggregation WTR3925 only Downlink inter-band (20 MHz and 20 MHz) Downlink intra-band Non-contiguous 20 MHz + 20 MHz Contiguous, 40 MHz for certain bands

-

-

-

-

1) RF Transmitter Part Transmit signal paths

-

-

Ten single-ended Tx outputs (4 LB, 4 MHB, and 2 HMLB) WTR3925/WTR3905 only Six single-ended Tx outputs (3 LB, 2 MHB, and 1 HMLB) WTR3900 only

- One 4-line analog baseband interface from modem IC (differential I and Q)

- One baseband-to-RF quadrature upconverter supports all Tx bands

- RF AGC amplifiers and filters LO generation and distribution

-

Single Tx PLL; divider and distribution circuits to support all Tx bands Tx bandpass filters

-

Eliminated for most modes/bands supported 1/12 LG Electronics Inc. 2 17-8-8 2) RF Receiver Part Primary receiver paths

- 14 single-ended PRx inputs (4 LB, 5 MB, 1 MLB, 4 HB)

- Three PRx/CA1 RF-to-baseband quadrature downconverters (LB, MB, HB)

- Three PRx/CA2 RF-to-baseband quadrature downconverters (LB, MB, HB)

- Baseband filtering and amplifiers

- Two single-ended I and Q interfaces to modem IC (PRx/CA1, PRx/CA2) Diversity receiver paths

-

-

-

14 single-ended DRx inputs (4 LB, 5 MB, 1 MLB, 4 HB) Three DRx/CA1 RF-to-baseband quadrature downconverters (LB, MB, HB) Three DRx/CA2 RF-to-baseband quadrature downconverters (LB, MB, HB)

- Baseband filtering and amplifiers Two single-ended I and Q interfaces to modem IC (DRx/CA1, DRx/CA2)

-

2. RF Transceiver (WTR4905) Multimode operation (See modem IC documents for specific capabilities)

- 3GPP GSM, GPRS, and EDGE

- 3GPP WCDMA Rel 99, HSDPA, HSUPA, HSPA+

- 3GPP LTE FDD and TDD Advanced RF techniques

- Mobile Rx diversity (but not SHDR due to single Rx VCO)

-

Simultaneous GNSS 1) RF Transmitter Part Transmit signal paths

- Wideband single-ended Tx outputs

- WTR4905 = 5

-

4-line analog baseband interface from modem IC (differential I & Q)

- One baseband-to-RF quadrature upconverter supports all Tx bands RF AGC amplifiers LO generation and distribution

-

Tx PLL; divider and distribution circuits to support all Tx bands External Tx bandpass filters Eliminated for most modes/bands supported

-

2) RF Receiver Part Primary receiver paths

-

Single-ended PRx inputs WTR4905 = 8 (3 LB, 3 MB, 2 HB) 2/12 LG Electronics Inc. 3 17-8-8

- PRx RF-to-baseband quadrature downconverters Two SAWless: LB for GSM, MB/HB for GSM and TD-SCDMA For all other WAN:

WTR4905 = 3 (LB, MB, and HB)

- Baseband filtering and amplifiers

-

2-line analog baseband interface to modem IC (single-ended I & Q)

- Diversity receiver paths

-

Single-ended DRx inputs WTR4905 = 7 (3 LB, 2 MB, 2 HB)

- DRx RF-to-baseband quadrature downconverters WTR4905 = 3 (LB, MB, and HB)

- Baseband filtering and amplifiers 2-line analog baseband interface to modem IC (single-ended I & Q)

-

3. Modem Part (MDM9615) The MDM9x40 is the latest-generation Qualcomm Technologies, Inc. (QTI) MDM device, which further expands mass-market chipset capabilities by making 3G and 4G high-speed data services accessible to more consumers in developed and developing countries. An MDM device is similar to a QTI MSM device, but without multimedia logic. The MDM9x40 chipset supports high-speed data capabilities over a wide range of air interface standards. The MDM9x40 device is fabricated using the advanced 20 nm SoC CMOS process, and is available in the 8.6 9.8 0.82 mm, 527-pin pico-scale package (527 PSP). It includes many ground pins for improved electrical grounding, mechanical strength, and thermal continuity. 4. Power Management Part (PMD9645) The PMD9645 device integrates all the wireless products power management, general housekeeping, and user interface support functions into a single mixed-signal IC. Its versatile design is suitable for any multimode, multiband product. The PMD9645 mixed-signal BiCMOS device is available in the 103-pin wafer-level nanoscale package (103 WLNSP) that includes ground pins for improved electrical ground, mechanical stability, and thermal continuity.

-

Input power management

- Output voltage regulation

- General housekeeping

- User interfaces

-

IC interfaces 3/12 LG Electronics Inc. 4 17-8-8 5. Clocks The PMIC includes several clock circuits whose outputs are used for general housekeeping functions, and elsewhere within the handset system. These circuits include a 19.2 MHz XO with multiple controllers and buffers, an MP3 clock output, an RC oscillator, and sleep-clock outputs. Performance specifications for these functions are presented in the following subsections.

-

19.2MHz : An external crystal is supplemented by on-chip circuits to generate the desired 19.2 MHz reference signal. Using an external thermistor network, the on-chip ADC, and advanced temperature compensation software, the PMIC eliminates the large and expensive VCTCXO module required by previous-generation chipsets. The XO circuits initialize and maintain valid pulse waveforms, and measure time intervals for higher-level handset functions. Multiple controllers manage the XO warmup and signal buffering, and generate the desired clock outputs. 4/12 LG Electronics Inc. 5 17-8-8 Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. RF Exposure Statement The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times. This device must not be co-located or operating in conjunction with any other antenna or transmitter. The highest permitted antenna gains including cable loss for use with this device are:

GSM 850 GSM 1900 WCDMA 2 WCDMA 4 WCDMA 5 LTE 2 LTE 4 LTE 5 LTE 12 LTE 13 LTE 17

-6.15 dBi

-7.09 dBi

-7.09 dBi

-8.05 dBi

-6.15 dBi

-7.09 dBi

-8.05 dBi

-6.15 dBi

-6.29 dBi

-6.46 dBi

-6.32 dBi End Product Labeling The module is labeled with its own FCC ID. If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following:

Contains FCC ID: BEJGEN11NAN 5/12 LG Electronics Inc. 6 17-8-8 OEM Responsibilities to comply with FCC Regulations The module has been certified for integration into products only by OEM integrators under the following condition: - The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times.

- The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. As long as the two condition above is met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed

(for example, digital device emissions, PC peripheral requirements, etc.). The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product. IMPORTANT NOTE: In the event that these conditions can t be met (for certain configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cant be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Manual Information To the End User This device complies with part 15 of the FCC rules Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 6/12

LETTER OF AUTHORIZATION FCC ID: BEJGEN11NAN 28 July 2020 I, the undersigned, hereby authorize Technical Manager Jungmin Yang and Dongmin Kim of SGS Korea Co., Ltd. and hereafter referred to as SGS Korea, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Technical Manager Jungmin Yang and Dongmin Kim of SGS Korea Co., Ltd. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing SGS Korea as our agent, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

c) make claims regarding certification only in respect of the scope for which certification has been granted;

d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

f) use certification only to indicate the products are certified as being in conformity with specified standards;

g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

i) j) keep a record of all complaints made known to the us relating to the products compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Kyung-Su Han Director, NA Regulatory & Environmental LG Electronics USA

LETTER OF REQUEST PERMISSIVE CHANGE 11 August 2020 We, as a manufacturer of following equipment, hereby submit Class 2 Permissive Change application for the FCC and the ISED to change components in the filings. MODEL GEN11NAN FCC FCC ID C2PC Grant Date Equipment Type BEJGEN11NAN 26 May 2020 Single Modular ISED Certification Number C2PC Grant Date HVIN PMN 2703H-GEN11NAN 26 May 2020 GEN11NAN GEN11NAN A. Change Note against the FCC / ISED C2PC grants issued in 5/26/2020. 1. FEM change [SKYA21049-> SKYA21049S]

- All parts without B4, B5 are same as before

- Replace TDK B4 duplexer with Skyworks B66 duplexer

- Replace Taiyo-Yuden B5 duplexer with Skyworks B26 duplexer old one. 2. RF Filter change

- B2/B4 2 in 1 Rx filter EOL Part (Broadcom) ACFM-2021-TR1 Alternative Part (RF360 ) B4385_1 Output power remains unchanged and the gain of any amplifiers in the FEM are the same as the 3. Removing or Changing some of components which are not related to RF part, are related to Digital part

- Remove MLCC Change Item : C8010, C8014, C8021, C8033, C8035, C8036, C8008, C8009, C8012, C8058 (Removal) Change Impact : Removal shunt components on the un-used line 1. no use of I2S between MDM and Neutrino : C8033, C8036, C8035, C8010 2. no use of PCM for BT : C8008, C8009, C8058, C8012 3. no use of 32K CLK for BT : C8021 4. no use of RESERVE_02 signal line : C8014

- MLCC 2nd Sourcing 2nd Source MLCC 2nd Current 2nd EAE63461911 33pF 5% 50V C0G 1005 Murata EAE63461912 100pF 5% 50V 1005 Murata EAE63461924 10pF +-5% 50V1005 Murata EAE63462004 2.2uF 10% 10V 1005 TDK EAE62971601 0.1uF 10% 50V 2012 Murata EAE61001701 2.2uF 6.3V 1005 Samhwa EAE64984501 100nF 10% 25V 1005 Samwha EAE65122701 100nF 10% 16V 1005 Samwha 0CZZB00035A 33pF 5% 50V 1005 TAIYO YUDEN EAE64361601 100pF 5% 50V 1005 TAIYO YUDEN EAE64821901 10pF 5% 50V 1005 TAIYO YUDEN EAE62962301 2.2uF -10% 10V 1005 Murata EAE65237401 100nF 10% 100V 2012 SAMSUNG EAE62962301 2.2uF 10V X5R 1005 Murata EAE63071107 100nF 10% 25V X7R 1005 Murata EAE63071107 100nF 10% 25V X7R 1005 Murata B. Test Requirements Due to the changes states above, we performed conducted output power, radiates spurious emission and radio frequency stability testing on Band 4 and Band 5 with BEJGEN11NAN. C. Declaration We declare all the functions and EMC/RF parameters except Band 4 and 5 are not affected by aforementioned changes. We hereby request permissive change for both FCC and ISED certification. Approved and signed by Company Name : LG Electronics, Inc. Name : Seunggu,.Kang Tel :+ 82-2-6950-5220 E-Mail : seunggu.kang@lge.com Seoul, Korea / 12 August 2020

(Place, date of issue)

(Signature / stamp) Seunggu, Kang / MANAGER

LG Electronics USA 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States July 27, 2020 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD 21046 REQUEST FOR CONFIDENTIALITY FCC ID: BEJGEN11NAN Pursuant to Sections 0.457 and 0.459 of the Commissions Rules (CFR 47), and Section 552

(b) (4) of the Freedom of Information Act, LG Electronics USA hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give LG Electronics USA temporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Temporary Confidential exhibits are listed as follows:

Confidential List Long-Term Short-Term Block Diagram Part list Schematics External Photos Internal Photos Test-Setup Photos The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Sincerely, Kyungsu Han Director Standards & Compliance LG Electronics USA

LETTER OF AUTHORIZATION FCC ID: BEJGEN11NAN 20 May 2020 I, the undersigned, hereby authorize Technical Manager Jungmin Yang and Dongmin Kim of SGS Korea Co., Ltd. and hereafter referred to as SGS Korea, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Technical Manager Jungmin Yang and Dongmin Kim of SGS Korea Co., Ltd. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing SGS Korea as our agent, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

c) make claims regarding certification only in respect of the scope for which certification has been granted;

d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

f) use certification only to indicate the products are certified as being in conformity with specified standards;

g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

i) j) keep a record of all complaints made known to the us relating to the products compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Kyung-Su Han Director, NA Regulatory & Environmental LG Electronics USA

REQUEST FOR CONFIDENTIALITY FCC ID: BEJGEN11NAN FCC ID: BEJ-TTA20ANEBR 20 May 2020 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules (CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, LG Electronics USA hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give LG Electronics USA temporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Temporary Confidential exhibits are listed as follows. Confidential List Long-Term Technical explanation for power reduction mechanism Antenna measurement information This authorization is valid until further written notice from the applicant. Kyung-Su Han Director, NA Regulatory & Environmental LG Electronics USA

LETTER OF REQUEST PERMISSIVE CHANGE 20 May 2020 MODEL GEN11NAN We, as a manufacturer of following equipment, hereby submit Class 2 Permissive Change application for the FCC and Class 3 Permissive Change for the ISED to have additional antennas in the filings. FCC FCC ID Original Grant Date Equipment Type BEJGEN11NAN 14 September 2017 Single Modular ISED Certification Number Original Grant Date HVIN PMN CURRENT FVIN C3PC FVIN

2703H-GEN11NAN 18 September 2017 GEN11NAN GEN11NAN N/A 6.65 TTA20ANEBR FCC ID Original Grant Date Equipment Type BEJ-TTA20ANEBR 16 May 2018 Telematics A. ANTENNA INFORMATION We have 11 antennas and gain was measured in each band. The worst-case scenarios have been chosen based on these values. We also confirm the measured gains are the highest gain in all directions and all frequencies. ID PART NUMBER MODEL NAME Cable Type Antenna Gain, Cable Loss Final Gain including Cable Loss 715 MHz 829 MHz 1732 MHz 1880 MHz 715 MHz 829 MHz 1732 MHz 1880 MHz 1 2 3 4 5 6 7 8 9 10 11

A A A A A A 2.13 dBi 3.72 dBi 0.49 dBi 6.10 dBi 2.04 dBi 5.52 dBi 4.69 dBi 3.32 dBi 4.64 dBi 2.31 dBi 4.90 dBi

-6.56 dBi

-5.80 dBi

-5.53 dBi

-4.03 dBi

-1.42 dBi 84744318 Sharkfin NA 42747534-39047412 Hexband 3 84728097 Sharkfin ChopTop 84719518-84664058 Hexband 2 84886535-22969192 Hexband 1 42756075-84664058 Hexband 4 84881230 MiniMega NA 84876043 T1xx 84744329 Sharkfin RoW 84884131 MiniMega RoW 84671653 Y2xx CABLE LOSS

- TYPE A CABLE LOSS

- TYPE B Antenna ID 1 to 10 share same cable type A, Only ID 11 has specific cable, type B.

-4.52 dBi

-6.95 dBi

-5.57 dBi

-4.48 dBi

-0.21 dBi

-1.13 dB

-0.88 dB

-1.29 dB

-0.65 dB

-0.82 dB

-0.62 dB 3.24 dBi 7.48 dBi 3.07 dBi 3.78 dBi 2.86 dBi 2.44 dBi 6.15 dBi 5.16 dBi 4.31 dBi 3.74 dBi 3.42 dBi 4.88 dBi A A A A A B B

-1.29 dB

-1.36 dB 3.70 dBi 2.90 dBi 1.43 dBi 3.35 dBi 2.34 dBi 4.83 dBi

-2.24 dBi 2.44 dBi 3.61 dBi 3.47 dBi 4.74 dBi

-4.85 dBi 3.81 dBi 4.23 dBi 3.38 dBi 0.01 dBi

-6.35 dBi

-7.44 dBi 0.75 dBi

-1.35 dBi 3.69 dBi 1.31 dBi

-0.39 dBi 4.81 dBi 2.33 dBi 0.19 dBi

-6.62 dBi

-6.45 dBi 1.95 dBi

-1.17 dBi 6.69 dBi 2.92 dBi

-5.36 dBi 6.19 dBi 5.33 dBi 3.22 dBi 2.60 dBi 2.90 dBi 1.57 dBi 1.86 dBi 3.29 dBi

-5.34 dBi

-1.09 dBi 1.78 dBi 1.93 dBi 5.03 dBi

-7.77 dBi 1.56 dBi 4.86 dBi 3.67 dBi 2.62 dBi 4.26 dBi 3.66 dBi 4.03 dBi 1.33 dBi B. WORST CASE SELECTION Frequency Range 0 kHz - 1GHz 1GHz - 30GHz Worst Case Antenna Peak Gain in range 84671653 Y2xx 84881230 MiniMega NA 4.26 dBi 6.19 dBi 84671653 Y2xx in 715MHz and 829 MHz. 84728097 Sharkfin ChopTop has slightly higher gain than the Y2xx in 829 MHz but overall gain is lower than Y2xx. Actual testing was performed with the Y2xx antenna but for ERP and MPE calculations, antenna gain 3.81 dBi shall be used as worst case. 84881230 MiniMega NA is the worst case for all frequencies above 1GHz. According to the KDB 178919 and KDB 996369, host manufacturer can use antenna including cable loss has gain less than following table. GSM 850, WCDMA 5, LTE 5 WCDMA 4, LTE 4 GSM 1900, WCDMA 2, LTE 2 LTE 12, LTE 13 3.81 dBi 6.19 dBi 5.33 dBi 4.26 dBi C. POWER REDUCTION To comply the ERP/EIRP limits and meet ERP thresholds for exemption from routine evaluation for MPE, power reduction mechanism is implemented on the module. Depending on the antenna selected for a specific vehicle installation the vehicle manufacturer can select a power of 1 dB in GSM 850, 3.5 dB in GSM 1900 as shown in the tables below. The end user cannot access the controls to reset the output power to the nominal settings to override the power reduction. EUT will be installed under the hood and users cannot reach the EUT itself. All the antennas shall be installed 20cm from any passengers or people around vehicle. Following table shows ERP/EIRP Calculation based on maximum production power. Note 1: Power reduction required for GSM 850 whenever the antenna gain exceed 2.81dBi for the 850 band. Max Tune-up Tolerance Final Gain Incl. Cable Loss Power Reduction 3.81 dBi 1 dB Note 1 34.66 dBm 38.45 dBm Final ERP ERP Limit Margin 26.11 dBm 34.77 dBm 26.11 dBm 34.77 dBm 8.66 dB 8.66 dB 3.79 dB 25.66 dBm 38.45 dBm 12.79 dB 25.66 dBm 38.45 dBm 12.79 dB Band Frequency LTE 12 LTE 13 701.5 MHz 779.5 MHz GSM 850 824.2 MHz WCDMA 5 826.4 MHz LTE 5 826.5 MHz Target Power 23 dBm 23 dBm 33 dBm 23 dBm 23 dBm Target Power Band Frequency WCDMA 4 1712.4 MHz 22.7 dBm LTE 4 1720 MHz 22.7 dBm WCDMA 2 1852.4 MHz 23 dBm LTE 2 1860 MHz 23 dBm 1 dB 1 dB 1 dB 1 dB 1 dB 1 dB 1 dB 1 dB 1 dB 1 dB Max Tune-up Tolerance 1 dB 4.26 dBi 4.26 dBi 3.81 dBi 3.81 dBi Final Gain Incl. Cable Loss 6.19 dBi 6.19 dBi 5.33 dBi 5.33 dBi Power Reduction Final EIRP EIRP Limit Margin 29.89 dBm 30.00 dBm 29.89 dBm 30.00 dBm 29.33 dBm 33.00 dBm 29.33 dBm 33.00 dBm 0.11 dB 0.11 dB 0.17 dB 3.67 dB 3.67 dB N/A GSM 1900 1850.2 MHz 30 dBm 5.33 dBi 3.5 dB 32.83 dBm 33.00 dBm GSM 900 880-915 MHz 33 dBm 3.61 dBi 2.5 dB 32.96 dBm N/A Note 1: Power reduction required for GSM 1900 whenever the antenna gain exceeds 2.0 dBi for the 1900 band.

Calculated ERP: Target Power + Tune-up Tolerance + Peak Gain - 2.15 dB Calculated EIRP: Target Power + Tune-up Tolerance + Peak Gain Final ERP/EIRP: ERP/EIRP - Power Reduction GSM 900 is not included in FCC/ISED certified scope but power reduction will be applied for Brazilian market. D. ERP/EIRP MEASUREMENT ERP/EIRP measurements were performed with the highest gain antenna configuration. GSM 850 was measured with Y2xx antenna which has antenna gain 3.66 dBi. Power reduction factor was applied, all the measured values comply under the ERP/EIRP limit. As GEN11NAN is a modular, test was performed in stand-alone configuration and both models were tested with production sample. Frequency

(MHz) Method

(ERP/EIRP) Ant. Pol. H or V Reading

(dBuV) AF

(dB) Conversion Factor (dB) ERP/EIRP ERP or EIRP

(dBm)

(mW) GEN11NAN GSM850 824.20 824.20 836.60 836.60 848.80 848.80 GSM1900 1 850.20 1 850.20 1 880.00 1 880.00 1 909.80 1 909.80 TTA20ANEBR GSM850 824.20 824.20 836.60 836.60 848.80 848.80 GSM1900 1 850.20 1 850.20 1 880.00 1 880.00 1 909.80 1 909.80 ERP ERP ERP ERP ERP ERP EIRP EIRP EIRP EIRP EIRP EIRP ERP ERP ERP ERP ERP ERP EIRP EIRP EIRP EIRP EIRP EIRP H V H V H V H V H V H V H V H V H V H V H V H V CL

(dB) 5.41 5.41 5.46 5.46 5.49 5.49 7.30 7.30 7.31 7.31 7.37 7.37 CL

(dB) 5.41 5.41 5.46 5.46 5.49 5.49 7.30 7.30 7.31 7.31 7.37 7.37 99.09 94.48 98.79 94.01 99.80 94.20 77.05 91.25 80.17 90.99 76.51 90.42 101.98 88.92 101.66 91.94 101.48 91.15 78.44 92.74 77.69 93.12 75.28 92.53 26.93 26.93 27.23 27.23 27.48 27.48 27.50 27.50 27.74 27.74 27.82 27.82 AF

(dB) 26.93 26.93 27.23 27.23 27.48 27.48 27.50 27.50 27.74 27.74 27.82 27.82

-97.41

-97.41

-97.41

-97.41

-97.41

-97.41

-95.26

-95.26

-95.26

-95.26

-95.26

-95.26

-97.41

-97.41

-97.41

-97.41

-97.41

-97.41

-95.26

-95.26

-95.26

-95.26

-95.26

-95.26 34.02 29.41 34.07 29.29 35.36 29.76 16.59 30.79 19.96 30.78 16.44 30.35 36.91 23.85 36.94 27.22 37.04 26.71 17.98 32.28 17.48 32.91 15.21 32.46 2524.89 873.46 2554.13 849.65 3437.50 946.77 45.63 1200.17 99.14 1197.41 44.08 1084.53 4911.82 242.80 4945.87 527.52 5061.07 469.08 62.84 1691.39 56.01 1955.43 33.21 1762.96 Frequency

(MHz) Method

(ERP/EIRP) Ant. Pol. H or V Reading

(dBuV) Conversion Factor (dB) ERP/EIRP ERP or EIRP

(dBm)

(mW) Both models with the highest gain antenna comply ERP/EIRP requirements, power thresholds for exemption from routine evaluation, MPE limits at 20cm and the limits in Parts 22, 24 and 27 of FCC rules and RSS standards has been based on maximum production power, including the power reduction for GSM modes as noted. Based on technical analysis mentioned above, we hereby request permissive change for both FCC and ISED certification. E. CONCLUSION Kyung-Su Han Director, NA Regulatory & Environmental LG Electronics USA