Cover Letter-Modular Approval
FCC ID: BEJTM03LNNAHD0
Date: June. 30, 2021
Gentlemen:
There’s a TM03LNNAHD0 that would like to have your authorization as a modular approval.
The specific product as below, TM03LNNAHD0 with its designed features and
specified description, meets special requirements for Single modular approval on FCC
KDB996369 by cross-reference list below.
Company
Model Name
Model Number
FCC ID
LG electronics
Telematics Module
TM03LNNAHD0
BEJTM03LNNAHD0
Requirement of FCC KDB996369
1. The modular transmitter must have its
own RF shielding.
2. The modular transmitter must have buffered
modulation/data inputs (if such inputs are
provided) to ensure that the module will
comply with Part 15 requirements under
rates or
conditions of
over-modulation.
excessive data
3. The modular transmitter must have its
own power supply regulation.
4. The modular transmitter must comply with the
antenna and transmission system requirements
of Sections 15.203, 15.204(b) and 15.204(c).
The antenna must either be permanently
attached or employ a “unique” antenna coupler
(at all connections between the module and the
antenna,
The
“professional installation” provision of Section
15.203 is not applicable to modules but can
apply to limited modular approvals under
paragraph (b) of this section.
including
cable).
the
5. The modular transmitter must be tested
in a stand‐alone configuration, i.e., the
module must not be inside another
device during testing.
Comply(Y/N)
Y
The EUT provides the RF shielding. See EUT
photo.
Y
The EUT has its buffered modulation. Please
see the Schematic Diagram.
Y
its own power supply
The EUT has
regulation, please see the Schematic Diagram.
Y
antenna
The EUT meets
requirements; photo of unique antenna are
shown in the test report.
the FCC
Y
The EUT was tested with a test board, Please
see test report and setup photo.
Y
The FCC ID is marked on the module top by
laser marking. Please, see laser marking draft
design on module top. This laser marking
design may be changed position or line, but
FCC ID is marked on the module.
Y
The EUT is compliant with all applicable
for
FCC
maintaining compliance are give in the User
Manual.
rules. Details
instructions
Y
The EUT complies with RF exposure
requirement.
6. The modular transmitter must be labeled with
its own FCC ID number, and, if the FCC ID is
not visible when the module is installed inside
another device, then the outside of the device
into which the module is installed must also
display a label referring to the enclosed
module. This exterior label can use wording
such as the following: “Contains Transmitter
Module FCC ID: BEJTM03LNNAHD0” or
“Contains FCC ID: BEJTM03LNNAHD0”
Any similar wording that expresses the same
meaning may be used. The Grantee may
either provide such a label, an example of
which must be included in the application for
equipment authorization, or, must provide
adequate instructions along with the module
which explain this requirement. In the latter
case, a copy of these instructions must be
included in the application for equipment
authorization.
7. The modular transmitter must comply
with any specific rule or operating
requirements applicable to the transmitter
and the manufacturer must provide adequate
instructions along with the module to
explain any such requirements. A copy of
these instructions must be included in the
application for equipment authorization.
8. The modular transmitter must comply
with any applicable RF exposure
requirements. For example, FCC Rules in
Sections 2.1091, 2.1093 and specific
Sections of Part 15, including 15.319(i),
15.407(f), 15.253(f) and 15.255(g), require
that Unlicensed PCS, UNII and millimeter
wave devices perform routine environmental
evaluation for RF Exposure to demonstrate
compliance. In addition, spread spectrum
transmitters operating under Section 15.247
are required to address RF Exposure
compliance in accordance with Section
15.247(b)(4).
Thank you.
Sincerely,
Title:
On behalf of: LG Electronics USA
By:
___________________
(Signature1)
___
Dae Woong Kim
_____
(Print name)