FCC ID: BEJTLVLM3IU-N Telematics

Product name : Telematics TLVLM3IU-N

(Online Connectivity Unit) Telematics LG Electronics Inc. What is the OCU(Online Connectivity Unit) Product Image Function Telematics product supporting Emergency Call/LTE service service Emergency Call Mobile Online Services Positioning/Dead Reckoning

-GPS/GNSS/Beidu/Galileo/SBAS LGE Confidential Specification Specification Dimension Supporting Bands GSM 850/1900 WCDMA B2/B4/B5 LTE FDD B2/B4/B5/B12/B17 Modem Chip Qualcomm MDM9628 GNSS GPS/Glonass/Beidou/SBAS/Galileo Bluetooth No WiFi Size Weight Power 2.4 GHz WIFI(b,g,n20) 130mm x 70.14mm x 37.5mm 300g DC 12V , 2A LGE Confidential OCU3 Low Hardware block diagram Confidential Figure 1.1. TL19BNN Block diagram LGE Confidential Notice FCC Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiating element of this device and the user. Industry Canada This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiating element of this device and the user. IC This device complies with license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :

(1)l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This radio transmitter has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p) is not more than that necessary for successful communication. Le prsent metteur radio a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. This device should be installed and operated with minimum distance 20cm between the radiating element of this device and the user. Cet appareil doit tre install et utilis avec une distance minimale de 20 cm entre l'lment rayonnant de cet appareil et l'utilisateur. The maximum antenna gain including cable loss must not exceed the table below;

Maximum antenna gain

(including cable loss)[dBi]

-

Frequency Range[MHz]

Band Main antenna including cable B2 B4 B5 B13 B12(17)

(Impedance: 50) 1850 ~ 1910 1710 ~ 1755 824 ~ 849 777 ~ 787 699 ~ 716

-4.26

-5.50

-2.52

-2.39

-2.92

-

-

-

-

-

Manufacture : LG Electronics Inc. 11/11

Agent Authorization Company: LG Electronics USA Address: 111 Sylvan Avenue North Building Englewood Cliffs New Jersey United States 07632 Product Name: Telematics FCC ID : BEJTLVLM3IU-N We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Date: 19 Aug 2022 Name:

Sung Soo Kim Title:

Director, Regulatory and Environmental Affairs Company: LG Electronics USA

September 15, 2022 Federal Communications Commission Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21046 USA Attn: OET Dept. Ref: FCC Class II Permissive change for FCC ID: BEJTLVLM3IU-N Applicant: LG Electronics USA Dear Examiner, This is to request a Class II Permissive change for FCC ID: BEJTLVLM3IU-N originally granted on 03/06/2019 (date). The change under this application are as below:

Shielding lid 1. Change related to the GSM/WCDMA/LTE transmitter section Item PCB Memory Crystal Change description AKM (T0002+Autolad3) replacement with AKM (DSR1000+EM526B) Micron memory(4G/4G) replace with new micron memory Change to 3017583 TXC OY19200004_A1 New shielding lid with slot position change according to new memory position 3700506 #1=>3017588 3700478#2 => 3017590 3700400#4 => 3017592 3401010 QORVO RF1494ASR Change to Maxscend MXDA85A1F

(3017758) TDK PCN TDK PCN TDK PCN Qorvo EOL-

000473 Antenna change Antenna model name: 5Q0.035.057.AJ NA 2. WLAN transmitter seciton There is no change for the WLAN section. Sincerely, Name: Sung Soo Kim Date: 09/15/2022 Title: Director, Regulatory and Environmental Affairs Signature of applicant

LG Electronics USA 111 Sylvan Avenue North Building Englewood Cliffs New Jersey United States 07632 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject; Request for Confidentiality FCC ID: BEJTLVLM3IU-N Date: 08/19/2022 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Sung Soo Kim Title: Director, Regulatory and Environmental Affairs