User Manual PRODUCT NAME : RF Module MODEL NAME : KSS104M The information contained herein is the exclusive property of LG Electronics and shall not be distributed, reproduced or disclosed in whole or no in part without prior written permission of LG Electronics. Index No Description Features 1 2 3 4 Picture of Product Installation and Function Block Diagram 5 Operating Conditions 6 RF specifications 7 Package guidance Page 1 1 2 3 3 4 4 1. Features The Keyssa Glass KSS104M Product family provides Generic High Speed solid- state convector solutions. Each Glass KSS104M contains one Keyssa transceiver
(SCVR) that can be configured to be a transmitter (Tx) or a receiver (Rx), allowing for unidirectional communication capability. When placed in proximity paired Glass KSS105Ms can establish an Extremely High Frequency (EHF) Communication link. For applications that use multiple Glass KSS104Ms on the same board, the KSS104Ms must be separated by a munimum of 15 mm center to center. The High Speed data must be DC-balanced 8b/10b coded to allow for clock recovery within the KSS105Ms and AC coupling of the high speed I/Os 2. Picture of Product 1/4 3. Installation and function Install the module(s) like below at the upper and(or) lower of the LED display for transmitting and receiving data such as videos, pictures and operational log. KSS104M installation position LED Display KSS104M installation position 42mm 12mm Cable 2/4 4. Block Diagram 5. Operating Conditions Parameter Min Typ Max Unit Operating Temperature Operating Humidity Storage Temperature Storage Humidity 0 10
-20 5
Supply Voltage 1.14 1.2 40 80 60 85 1.3
Vdc 3/4 ASK (Amplitude Shift Keying) Frequency Range Output power (Max. dBm e.i.r.p) 57 GHz to 64 GHz 9 6. RF specifications FCC ID: BEJKSS104M IC: 2703H-KSS104M 7. Package guidance Label LG Electronics Inc. Model Name: KSS104M FCC ID: BEJKSS104M IC: 2703H-KSS104M 4/4 8. Compliance statements 1) FCC Statements FCC Part 15.19 Statements:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. FCC Part 15.21 statement Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Regulatory notice to host manufacturer according to KDB 996369 D03 OEM Manual v01 List of applicable FCC rules This module has been granted modular approval as below listed FCC rule parts.
- FCC Rule parts 15C(15.255) Summarize the specific operational use conditions
-The OEM integrator should use equivalent antennas which is the same type and equal or less gain then an antenna listed below in this instruction manual. The module has been certified for integration into products only by OEM integrators RF exposure considerations under the following condition:
-The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times.
-The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except the simultaneous transmission condition described in operational description and in accordance with FCC multi-transmitter product procedures.
- Mobile use product manuals. As long as the three conditions above are met, further transmitter testing will not be required. OEM integrators should provide the minimum separation distance to end users in their end-
8. Compliance statements 1) FCC Statements Antennas list This module is certified with the following integrated antenna.
- Type: Differential patch antenna (Peak gain (dBi): 5.3 dBi) Any new antenna type, higher gain than listed antenna should be met the requirements of FCC rule 15.203 and 2.1043 as permissive change procedure. The module is not be labeled with its own FCC ID and IC Certification Number since impractical to be labeled on it. So, final end product which the module is installed must be Label and compliance information End Product Labeling labeled in a visible area with the following:
Contains FCC ID: BEJKSS104M Contains IC: 2703H-KSS104M Information on test modes and additional testing requirements
- OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, additional transmitter in the host, etc.). Additional testing, Part 15 Subpart B disclaimer
-The final host product also requires Part 15 subpart B compliance testing with the modular transmitter installed to be properly authorized for operation as a Part 15 digital device. Specific Host Device Platform
-This 60 GHz transmitter module was tested while equipped into the LG`s LED Screen. So, this transmitter must be installed into only series model of this LG`s LED Screens with the identical area of concen for this module installation. Otherwise, C2PC is required according to FCC Rule 2.1043 before installing into any other host device. Test requirements about not Shielding Since this transmitter module is not sheilded, the module manufacturer should perform the test that the module is compliant in the host device. 8. Compliance statements 2) ISED Statements RSS-GEN, Sec. 7.1.3(licence-exempt radio apparatus) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
(1) lappareil ne doit pas produire de brouillage, et
(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. RF Exposure The antenna (or antennas) must be installed so as to maintain at all times a distance minimum of at least 20 cm between the radiation source (antenna) and any individual. This device may not be installed or used in conjunction with any other antenna or transmitter. l'exposition aux RF Lantenne (ou les antennes) doit tre installe de faon maintenir tout instant une distance minimum de au moins 20 cm entre la source de radiation (lantenne) et toute personne physique. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. Attention:
Les changements ou modifications de cet appareil non expressment approuv par le fabricant peuvent annuler votre droit utiliser cet quipement. tiquetage du produit final (IC) Le module nest pas tiquet avec son propre ID FCC et numro de certification IC depuis peu pratique dtre tiquet sur elle. Ainsi, le produit final que le module est install doit tre tiquet dans une zone visible avec les lments suivants : :
Contient module metteur IC : 2703H-KSS104M