User Manual PRODUCT NAME : Single Band Wi-Fi + MCU Module MODEL NAME : LCW-003 LGIT NAME : TWFB-E351D REG. DATE : 2015. 09. 10 REV. DATE : 2015. 09. 10 Specification For Approval MODEL NAME : LCW-003 REV. NO : 1 0 PAGE :
1 / 14 Page 2 2 3 3 4 7 8 9 10 Table of Contents No Description 1 2 3 4 5 6 7 8 Features Block Diagram Storage conditions Operating Test Conditions Electrical Characteristics Pin Description Outline Drawing Packing Information 9 Warning Statement 2015 LGIT. All rights reserved. REG. DATE : 2015. 09. 10 REV. DATE : 2015. 09. 10 Specification For Approval MODEL NAME : LCW-003 REV. NO : 1 0 PAGE :
2 / 14 1. Features TWFB-E301D is the module for IEEE 802.11b/g/n wireless LAN + MCU. TWFB-E301D is based on Qualcomm QCA4010 solution. IEEE 802.11 b/g/n HT20 single band WLAN Infrastructure Size : 32mm x 48mm x 9.35 mm Auto-calibration(RF, Crystal) Data rates up to 65Mbps PHY rate UART interface Integrated IPv4/IPv6 TCP/IP stack Integrated Network services such as HTTP, DNS, FTP Security : WFA, WPA, WPA2, WEP, WAPI, TKIP Application : Home Appliance 2. Block Diagram ANT QCA4010 CPU
(Xtensa 7) ROM 1MB Interface Block RAM 1.5MB PMU UART JTAG USB Flash Memory
(4MB) 802.11n WLAN MAC/BB Clock(40MHz) I2C Homekit 3.3V DC-DC 5V,12V 2015 LGIT. All rights reserved. REG. DATE : 2015. 09. 10 REV. DATE : 2015. 09. 10 Specification For Approval MODEL NAME : LCW-003 REV. NO : 1 0 PAGE :
3 / 14 3. Storage conditions Parameter Storage Temperature Storage Humidity (@ 40) Min
-20
-
Max
+80 90 Unit
%
Caution : The specifications above the Table define levels at which permanent damage to the device can occur. Function operation is not guaranteed under these conditions. Operating at absolute maximum conditions for extend periods can adversely affect the long-term reliability of the device. Other conditions 1) Do not use or store modules in the corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are contained. Also, avoid exposure to moisture. 2) Store the modules where the temperature and relative humidity do not exceed 5 to 40 and 20 to 60%. 3) Assemble the modules within 6 months. Check the soldering ability in case of 6 months over. 4. Operating Test Conditions Parameter Operating Temperature Operating Humidity (40) Supply Voltage Min 0
-
4.5 10.8 Typ
-
-
5.0 12 Max
+60 85 5.5 13.2 Unit
%
Vdc 2015 LGIT. All rights reserved. REG. DATE : 2015. 09. 10 REV. DATE : 2015. 09. 10 Specification For Approval MODEL NAME : LCW-003 REV. NO : 1 0 PAGE :
4 / 14 5. Electrical Characteristics 5-1. RF Characteristics for IEEE802.11b (11Mbps mode unless otherwise specified) Items Specification Mode Channel frequency Data rate TX Characteristics Power Level Spectrum Mask 1st side lobes ( to fc 11MHz) 2nd side lobes ( to fc 22MHz) Modulation Accuracy (EVM) Power On/Off ramp Freq. Tolerance Chip Clock Freq. Tolerance Contents IEEE802.11b DSSS/CCK 2400 ~ 2483 MHz 1,2,5.5,11Mbps Typ. Max. 17 21
-43
-58 30 0.5
-
-
-30
-50 35 2.0 25 25 Min. 13
-
-
-
-
-25
-25 RX Characteristics Min. Typ. Max. Minimum Input Level Sens. (FER 8%) Maximum Input Level (FER 8%)
-10
* Normal Condition : 25, VDD=5V.
* RF characteristics is board limit. It can differ according to standards 2015 LGIT. All rights reserved.
-88
-
-76
-
Unit dBm dBr dBr
%
Usec ppm ppm Unit dBm dBm REG. DATE : 2015. 09. 10 REV. DATE : 2015. 09. 10 Specification For Approval MODEL NAME : LCW-003 REV. NO : 1 0 PAGE :
5 / 14 5-2. RF Characteristics for IEEE802.11g (54Mbps mode unless otherwise specified) Items Specification Mode Channel frequency Data rate Contents IEEE802.11g OFDM 2400 ~ 2483 MHz 6,9,12,18,24,36,48,54Mbps TX Characteristics Min. Typ. Max. Power Level Spectrum Mask at fc 11MHz at fc 20MHz at fc 30MHz Constellation Error (EVM) Freq. Tolerance Chip Clock Freq. Tolerance 10 14 18
-
-
-
-
-20
-20
-32
-43
-48
-32
-
-
-20
-28
-40
-25 20 20 RX Characteristics Min. Typ. Max. Minimum Input Level Sens. (PER 10%) Maximum Input Level (PER 10%)
-
-20
-73
-
-65
-
* Normal Condition : 25, VDD=5V.
* RF characteristics is board limit. It can differ according to standards 2015 LGIT. All rights reserved. Unit dBm dBr dBr dBr dB ppm ppm Unit dBm dBm REG. DATE : 2015. 09. 10 REV. DATE : 2015. 09. 10 Specification For Approval MODEL NAME : LCW-003 REV. NO : 1 0 PAGE :
6 / 14 5-3. RF Characteristics for IEEE802.11gn (MCS7 mode unless otherwise specified) Items Specification Mode Channel frequency Data rate Contents IEEE802.11n 2.4GHz OFDM 2400 ~ 2483 MHz 6.5,13,19.5,26,39,52,58.5,65Mbps TX Characteristics Min. Typ. Max. Power Level (HT20 : MCS7) Spectrum Mask (HT20) at fc 11MHz at fc 20MHz at fc 30MHz Constellation Error (EVM) Freq. Tolerance Chip Clock Freq. Tolerance 9
-
-
-
-
-20
-20 13 17
-32
-35
-45
-32
-
-
-20
-28
-40
-28 20 20 RX Characteristics Min. Typ. Max. Minimum Input Level Sens.
(HT20,PER 10%) Maximum Input Level (PER 10%)
-
-20
-68
-
-64
-
* Normal Condition : 25, VDD=5V.
* RF characteristics is board limit. It can differ according to standards 2015 LGIT. All rights reserved. Unit dBm dBr dBr dBr dB ppm ppm Unit dBm dBm REG. DATE : 2015. 09. 10 REV. DATE : 2015. 09. 10 Specification For Approval MODEL NAME : LCW-003 REV. NO : 1 0 PAGE :
7 / 14 6. Pin Description Pin No. Pin Name I/O Pin Description 1 2 3 4 VDD UART Rx UART Tx GND I I O
-
VDD 5.0V, 12V 5%
UART Communication signal line UART Communication signal line GND
< TOP View > < Bottom View >
4 1 Note. 1) Recommend a Module install sequence for prevent UART device failure
- Supply 5.0V, 12V power
- Connect to data signal (UART Tx, UART Rx) 2) Connector: 4Pin SMD Connector A 2015 LGIT. All rights reserved. REG. DATE : 2015. 09. 10 REV. DATE : 2015. 09. 10 Specification For Approval MODEL NAME : LCW-003 REV. NO : 1 0 PAGE :
8 / 14 7. Outline Drawing 2015 LGIT. All rights reserved. REG. DATE : 2015. 09. 10 REV. DATE : 2015. 09. 10 Specification For Approval MODEL NAME : LCW-003 REV. NO : 1 0 PAGE :
9 / 14 8. Packing Information 2015 LGIT. All rights reserved. REG. DATE : 2015. 09. 10 REV. DATE : 2015. 09. 10 Specification For Approval MODEL NAME : LCW-003 REV. NO : 1 0 PAGE :
10 / 14 9. Warning Statement
<FCC Warning Statements>
FCC Part 15.19 Statements:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. FCC Part 15.105 statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Part 15.21 statement Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. 2015 LGIT. All rights reserved. REG. DATE : 2015. 09. 10 REV. DATE : 2015. 09. 10 Specification For Approval MODEL NAME : LCW-003 REV. NO : 1 0 PAGE :
11 / 14 9. Warning Statement RF Exposure Statement The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times. This device must not be co-located or operating in conjunction with any other antenna or transmitter. End Product Labeling The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification Number are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following:
Contains FCC ID: BEJ-LCW003 Contains IC: 2703N-LCW003
<IC Warning Statements>
RSS-GEN, Sec. 7.1.3 (licence-exempt radio apparatus) This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. 2015 LGIT. All rights reserved. REG. DATE : 2015. 09. 10 REV. DATE : 2015. 09. 10 Specification For Approval MODEL NAME : LCW-003 REV. NO : 1 0 PAGE :
12 / 14 9. Warning Statement RF Exposure The antenna (or antennas) must be installed so as to maintain at all times a distance minimum of at least 20 cm between the radiation source (antenna) and any individual. This device may not be installed or used in conjunction with any other antenna or transmitter. l'exposition aux RF Lantenne (ou les antennes) doit tre installe de faon maintenir tout instant une distance minimum de au moins 20 cm entre la source de radiation
(lantenne) et toute personne physique. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. Attention: Les changements ou modifications de cet appareil non expressment approuv par le fabricant peuvent annuler votre droit utiliser cet quipement. tiquetage du produit final (IC) Le module BT111 est tiquet avec sa propre identification FCC et son propre numro de certification IC. Si lidentification FCC et le numro de certification IC ne sont pas visibles lorsque le module est install lintrieur dun autre dispositif, la partie externe du dispositif dans lequel le module est install devra galement prsenter une tiquette faisant rfrence au module inclus. Dans ce cas, le produit final devra tre tiquet sur une zone visible avec les informations 2015 LGIT. All rights reserved. REG. DATE : 2015. 09. 10 REV. DATE : 2015. 09. 10 Specification For Approval MODEL NAME : LCW-003 REV. NO : 1 0 PAGE :
13 / 14 9. Warning Statement suivantes :
Contient module metteur identification FCC ID : BEJ-LCW003 Contient module metteur IC : 2703N-LCW003 The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product. OEM Responsibilities to comply with FCC and Industry Canada Regulations The module has been certified for integration into products only by OEM integrators under the following condition:
- The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-
transmitter product procedures. As long as the two condition above is met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cant be met (for certain configurations or co-location with another transmitter), then the FCC and Industry Canada authorizations are no longer considered valid and the FCC ID and IC Certification Number cant be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC and Industry Canada authorization. 2015 LGIT. All rights reserved. REG. DATE : 2015. 09. 10 REV. DATE : 2015. 09. 10 Specification For Approval MODEL NAME : LCW-003 REV. NO : 1 0 PAGE :
14 / 14 9. Warning Statement Responsabilits des OEM quant la conformit avec les rglementations de FCC et d Industrie Canada Les modules ont t certifis pour entrer dans la fabrication de produits exclusivement raliss par des intgrateurs dans les conditions suivantes :
- Le module transmetteur ne doit pas tre install ou utilis en concomitance avec une autre antenne ou un autre transmetteur. Tant que ces deux conditions sont runies, il nest pas ncessaire de procder des tests supplmentaires sur le transmetteur. Cependant, lintgrateur est responsable des tests effectus sur le produit final afin de se mettre en conformit avec dventuelles exigences complmentaires lorsque le module est install
(exemple : missions provenant dappareils numriques, exigences vis--vis de priphriques informatiques, etc.) REMARQUE IMPORTANTE : En cas dinobservance de ces conditions (en ce qui concerne certaines configurations ou lemplacement du dispositif proximit dun autre metteur), les autorisations de FCC et dIndustrie Canada ne seront plus considres valables et lidentification de FCC et le numro de certification dIC ne pourront pas tre utiliss sur le produit final. Dans ces cas, lintgrateur OEM sera charg dvaluer nouveau le produit final (y compris lmetteur) et dobtenir une autorisation indpendante de FCC et dIndustrie Canada.
- Dans le guide dutilisation du produit final, lintgrateur OEM doit sabstenir de fournir des informations lutilisateur final portant sur les procdures suivre pour installer ou retirer ce module RF ou pour changer les paramtres RF. 2015 LGIT. All rights reserved.