Order Number
: GETEC-C1-12-369 Test Report Number
: GETEC-E3-12-130 FCC Part 15 subpart C Page 1 / 1 APPENDIX H
: USERS MANUAL EUT Type: WLAN module FCC ID.: BEJPCRCUDT2 WLAN 802.11b/g/n Module WLAN Linux Board Manual for Air Conditioner Warranty period: 2 years A/S: 1544-7777, 1588-7777 CONTENTS 1 INTRODUCTION.....4 1.1 Overview4 1.2 Key Features.4 2 HARDWARE ARCHITECTURE5 2.1 Block Diagram..5 2.2 Order information.5 3 ELECTRICAL DATA...6 3.1 Absolute maximum ratings..6 3.2 Electro Static Discharge (ESD)...6 3.3 Recommended operating conditions.....6 3.4 Power Consumption.6 3.5 RF Performance....7 4 INTERFACES..9 4.1 UART Pin Configuration.10 4.2 JTAG Connector..10 5 APPLICATION INFORMATION.12 5.1 Power supply.12 5.2 SDRAM..12 5.3 Flash...12 5.4 Linux Boot...12 5.5 Serial interface UART..12 5.6 I2C Interface UART..12 5.7 RF interface...12 5.8 Environmental statement.12 6 PACKAGE SPECIFICATIONS13 6.1 Mechanical outline of the WLAN module circuit board.......13 6.2 Markings on the WLAN module.......13 7 TARGETED STANDARDS COMPLIANCE.......14 7.1 IEEE/IETF.14 7.2 WLAN .......14 8 Notice................................................... 15 8.1 FCC (Certification)....15 8.2 IC (Certification)..........................16 1. INTRODUCTION 1.1 Overview WLAN module is a high performance module with WLAN and a micro processor including external memories and all peripheral components required. It is a complete solution designed to be function as a standalone communication module, serial cable replacement or as an easy to use WLAN addition with a minimal resource need, to an existing system. WLAN module enables a cost efficient, high performance and feature rich client solution. It provides up to 72 Mbit/s data rate. The WLAN module is a full fledge Linux computer that enables a multitude of advanced features. The WLAN module can operate stand alone or connected to a host via the serial interface. 1.2 Key Features ARM9 based MCU Integrated IP-stack Single stream 1x1 802.11n Data Rates:1,2,5.5,6,7.2,9,11,12,14.4,18,21.7,24,28.9,36,43.3,48,54,57.8,72,2 Mbps Modulation: QPSK, 16QAM, 64QAM DBPSK, DQPSK, CCK, OFDM with BPSK WEP and AES hardware encryption accelerator up to 128 bits Soft AP Linux support Single Supply Voltage 5 V - 12 V Small footprint RoHS Compliant Integrated Chip antenna Temperature range -20 to + 70 2. HARDWARE ARCHITECTURE 2.1 Block Diagram Figure 2-1 Block Diagram 2.2 Order information Table 2-1 Ordering Information 3. ELECTRICAL DATA 3.1 Absolute maximum ratings Table 3-1 Absolute maximum ratings. Exceeding any of the maximum ratings, even briefly lead to deterioraton in Performance or even destruction. Values indicates condition applied one at the time Rating Supply voltage Input RF level Storage temperature Min. 0
-50 Max. 15 10
+125 Unit V dBm C 3.2 Electro Static Discharge (ESD) WLAN module withstands ESD voltages up to 2000 V HBM (Human Body Model) According to JESD22-A114 and up to 300 V MM (Machine Model) according to JESD22-A115. 3.3 Recommended operationg conditions Table 3-2 Recommended operating conditions Rating Supply Voltage VCC Operating temperature WLAN module 3.4 Power Consumption 3.4.1 Current Consumption Min. 5.0
-20 Typ.
+25 Max. 12.0
+70 Unit V C Table 3-3 Current consumption in different modes MCU running at 400MHz and system clock at 100MHz. Mode Conditions Parameter Voltage Min. Typ. Max. Unit All modes TX [802.11b], 11 Mbps TX [802.11g], 54 Mbps TX [802.11n], MCS7 RX [802.11b], 11 Mbps RX [802.11g], 54 Mbps RX [802.11n], MCS7 Peak 25C 25C 25C 25C 25C 25C VCC VCC VCC VCC VCC VCC VCC 12 V 12 V 12 V 12 V 12 V 12 V 12 V 100 mA mA mA mA mA mA mA 100 83 73 47 47 47 3.4.2 Power Consumption The power consumption is estimated for a scenario where the WLAN module is in station mode and transmits 1% of the time. Conditions : Tamb=25oC, VCC=12 V Table 3.4 Power consumption in different modes. *Output power referred to antenna port n WLAN module Mode Output Power*
Power Consumption Comments Station 11b
+11 dBm Station 11g
+15 dBm Station 11n
+11 dBm 830 mW 832 mW 831 mW 11 Mbit/s, MCU 400/100MHz 54 Mbit/s, MCU 400/100MHz MCS7, MCU 400/100MHz 3.5 RF Performance(USA, Canada 2412 ~ 2462MHz) VCC= 12 V, Tamb= -20 to +70oC, at antenna port on WLAN module. Table 3-5 RF Performance Parameter Conditions Frequency range Min. 2412 Typical Max. 2472 Units MHz Transmitter performance Output power QPSK, Calibrated Output power Output power QFDM 54 Mbit/s, Calibrated MCS7 Mbit/s, Calibrated EVM at +18 dBm CCK, ch, 1- ch. 13 EVM at +12 dBm CCK, ch. 14 EVM at +16 dBm OFDM 802.11b/g EVM at +15 dBm OFDM 802.11b/g EVM at +14 dBm OFDM 802.11b/g EVM at +15 dBm OFDM 802.11n EVM at +14 dBm OFDM 802.11n Receiver performance 11b/g Receiver sensitivity DPSK 1 Mbit/s Receiver sensitivity QDPSK 2 Mbit/s Receiver sensitivity Receiver sensitivity CCK/DPSK 5.5 Mbit/s CCK/BPSKK 11 Mbit/s
+8
+13
+11
+15
+14
+17 dBM dBM
+9.5
+11
+15 dBM 13 31 4.8 3.4 3.0 3.7 3.1
-95
-93
-91
-88 35
dBM dBM dBM dBM Receiver sensitivity OFDM 6 Mbit/s Receiver sensitivity OFDM 9 Mbit/s Receiver sensitivity OFDM 12 Mbit/s Receiver sensitivity OFDM 18 Mbit/s Receiver sensitivity OFDM 24 Mbit/s Receiver sensitivity OFDM 36 Mbit/s Receiver sensitivity OFDM 48 Mbit/s Receiver sensitivity OFDM 54 Mbit/s Receiver performance 11n Receiver sensitivity Receiver sensitivity Receiver sensitivity Receiver sensitivity Receiver sensitivity Receiver sensitivity Receiver sensitivity Receiver sensitivity OFDM/BPSK 7.2 Mbit/s OFDM/BPSK 14.4 Mbit/s OFDM/BPSK 21.7 Mbit/s OFDM/16-QAM 28.9 Mbit/s OFDM/16-QAM 43.4 Mbit/s OFDM/16-QAM 57.8 Mbit/s OFDM/16-QAM 65 Mbit/s OFDM/16-QAM 72.2 Mbit/s
-91
-90
-88
-86
-83
-80
-76
-74
-90
-88
-86
-83
-79
-72
-70
-69 dBM dBM dBM dBM dBM dBM dBM dBM dBM dBM dBM dBM dBM dBM dBM dBM 4. INTERFACES Figure 4-1 WLAN module pins Connector type Description USB Type A Male Power Supply and UART (Application dependent) 2x5 1.25 mm pin header JTAG (normally not mounted) Mini USB Boot loader port 4 pin 2.54 mm pin header UART (debug) Not Mounted 2 pin 2.54 mm pin header Boot load enable jumper 6 pin FCC connector 12C to external EEPROM Low profile tactile switch Application controlled functionallity P1 P2 P3 P4 P5 P6 S1 4.1 UART Pin Configuration 4.1.1 Pin assignments USB Type A male connector Table 4-1 Pin Description for the USB Type A male connector Pin Function Type Description 1 2 3 4 VCC GND UART_RX UART_TX S S I O 12 V power Ground RX TX The UART_TX and UART_RX pins has an onboard level shifter to accept signal with voltage swings up to 5 V. To ensure good signal quality the signals needs to have a pull-up resistor on the connecting side. Note: The pin out is not standard USB pin out the WLAN module may be damaged if connected to a standard USB socket!
4.2 JTAG Connector The JTAG connector is used during development only and not mounted in production. 4.2.1 Pin out JTAG connector Pin Function Type Description 1 2 3 4 JTAG_TCK GND JTAG_TDO 3V3 S S I O JTAG Clock Ground 3.3 VOLT 5 6 7 8 9 10 JTAG_TMS RESET_n NC NC JTAG_TDI GND I/O I/O
I/O S NO Connection NO Connection Ground 5. APPLICATION INFORMATION 5.1 Power Supply WLAN module should be powered by 5 V to 12 V supply on +, pin 1 of the USB type A male connector. 5.2 SDRAM The WLAN module has 64 Mbytes RAM whereof 52 Mbytes is available for user application. 5.3 FLASH The WLAN module has 128 Mbytes whereof 112 Mbytes is available for user application. 5.4 Linux Boot The Linux boot takes about 30s to complete before the consol interface (UART 2) can be used. 5.5 Serial interface UART To communicate with the WLAN module has two UART interfaces. 5.5.1 UART 1 This interface is used for user applications. 5.5.2 UART 2 The UART2 interface is use for configuration and debug The pin order is as follows, pin one closest to push button:
Pin 1: 3.3 V Pin 2: RX_D(PA21 on MCU) Pin 3: TX_D(PA22 on MCU) Pin 4: GND The supply pins(3.3 V and GND)can be used to power a TTL-CMOS to RS-232 conversion board. Highest supported baud rate on this port is 115200. The pin header for this interface is normally not mounted on the PCB. 5.6 12C Interface The WLAN module has an 12C serial interface to an external ST EEPROM, M24LR64-R MN 6. The FFC connector for this interface is normally not mounted on the PCB. 5.7 RF interface The WLAN module has a high performance chip antenna as the primary RF interface. 5.8 Environmental statement The WLAN module is designed and manufactured to comply with the RoHS and Green directives. 6. PACKAGE SPECIFICATIONS 6.1 Mechanical outline of the WLAN module circuit board 6.2 Markings on the WLAN module The EMC Shield is labeled with serial number and MAC address 7. TARGETED STANDARDS COMPLIANCE Description WLAN MAC& PHY High rate DSSS (5,5/11 Mbit/s) Operation in different regulatory domains QoS enhancements Extended rate PHY (ERP-PBCC, DSS-OFDM) Security enhancements Longer Range, Faster Throughput Fast BSS transition Bridge tunneling Frame encapsulation Draft 11.0, 2008 Wireless network management 7.1 IEEE / IETF Table 7.1 Applicable IEEE standards Standard Revision 802.11 802.11b 802.11d 802.11e 802.11g 802.11i 802.11k 802.11n 802.11r 802.11h 802.11 R2003 802.11 R2003 802.11 R2003 D9,0 Aug. 2004
-2003
-2004 Spec released Oct 29tn 2009 Draft 9.0, 2008 1997 edition RFC1023 Inherent 7.2 WLAN Table 7.2 Applicable WLAN standards Specification Description Revision WLAN 802.11b with WPA system inter Operability test plan for IEEE 802.11b devices 802.11b devices with WPA WLAN 802.11g with WPA system inter Operability test plan 802.11g devices with WPA 2.1 2.0 8. Notice WARNING This device is not available for laptop or similar portable system. 8.1 FCC (Certification) This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation FCC WARNING: This equipment may generate or use radio frequency energy. Changes or m odifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate t his equipment if an unauthorized change or modification is made. U.S. Regulatory Wireless Notice This products emits radio frequency energy, but the radiated output power of this device is far below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact with the antenna during normal oper ation is minimized. FCC Radiation Exposure Statement This equipment compiles with FCC radiation exposure limits set forth an uncontrolled enviro nment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Federal Communications Commission (FCC) Statement You are cautioned that changes or modifications not expressly approved by the part respon sible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a class B digital de vice, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable p rotection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance to radio communications. However, there is no guarantee that interference will not occur in a p articular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encou raged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. End Product Labeling The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the devic e into which the module is installed must also display a label referring to the enclosed mod ule. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: BEJPCRCUDT2 or Contains FCC ID: BEJPCRCUDT2. Any similar wording that expres ses the same meaning may be used. The Grantee may either provide such a label, an examp le of which must be included in the application for equipment authorization, or, must provid e adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authori zation. 8.2 IC (Certification) This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:
1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device IC Warning This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesire d operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radi o exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. IC Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled envi ronment. This equipment should be installed and operated with minimum distance 20 cm b etween the radiator & your body. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE C AUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS C OULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.