FCC ID: Q87-RE6400 Linksys Range Extender

User Guide RE6300/RE6400 Introduction This User Guide can help you connect the extender to your network and solve common setup issues. You can find more help from our award-winning, 24/7 customer support at Linksys.com/support. Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 How to install the range extender................ 2 How to access the browser-based utility .......... 5 Using range extender settings X Using Wi-Fi Protected Setup..................... 7 How to use Site Survey.......................... 9 Cross-Band AC Power Pass-Through Wireless Music Playback Troubleshooting................................ 10 Specifications.................................. 13 Overview Front RE6300 RE6400 The light on the front of the range extender gives you information about power, updating and signal strength. Power Light Status/ description Blinking Green Booting up Resetting to factory defaults Upgrading firmware Solid Green Ready to use Solid Orange Weak connection with the router Fix: Unplug the extender, and move it closer to the router Blinking Orange Not connected to the router Other error Fix: Unplug the extender, plug it back in, wait two seconds, reconnect to your network Side Power Switch European versions only. Wi-Fi Protected Setup Button and LED Use Wi-Fi Protected Setup to automatically and securely add compatible wireless devices to your network. Refer to Using Wi-Fi Protected Setup on page 7. Reset Press and hold for about five seconds to reset to factory defaults. You can also restore the defaults from the Administration > Factory Defaults screen in the extenders browser-based utility. Bottom Ethernet (blue) Connect wired devices to your wireless network with Ethernet (network) cables. The green light turns on when an Ethernet device is connected and active on this port. The light blinks when the extender is sending or receiving data over the Ethernet port. How to install the range extender Before setup, unplug or disconnect any range extenders on the network. 1. Plug in the range extender midway between your router and the area without Wi-Fi. Be sure you have at least 50% of your routers Wi-Fi signal at that point on the device you will use for setup. The setup software will help you find the best spot if you have trouble.

<Diagram>

2. Wait for a solid light on the cover of the range extender. It could take up to two minutes. On a computer, phone or tablet, connect to the Wi-Fi network Linksys Extender Setup.

<diagram2>

3. If setup doesnt start automatically, open a browser to http://extender.linksys.com. Linksyss Spot finder technology will help you find the right location for your range extender if you have trouble. You will be guided to place the range extender closer or farther from your router to improve the signal. If you nailed it with your first placement you will not see Spot finder screens.

<screenshot of Too Far page>

4. During setup you will be asked whether you want the range extender to update itself automatically. If you allow automatic updates, the range extender will download and install updates when released by Linksys. Automatic updates will take place overnight so they do not disrupt your network activity. You also can decide to manually update your range extender at your convenience.

<screen shot>

Post set-up LED behavior mention here as well and in the QSG TIP You can also connect the range extender by using Wi-Fi Protected Setup. For more information, see Using Wi-Fi Protected Setup on page 7. Special Feature - Music Streaming Wireless Music Playback Stream music through your AC1200 MAX range extender to connected speakers. iOS devices:

Connect iOS device to the same Wi-Fi network as your range extender. Swipe up from the bottom of your screen. Tap on Linksys Range Extender. Android devices For Samsung Galaxy Connect Galaxy device to the same Wi-Fi network as your range extender. Select Music app Choose music file and tap Screen Mirroring icon Choose Linksys Range Extender. Your screen might look different depending on your device model and version of Android. For other Android devices, stream music with MediaHouse, UPnPlay, Skifita, ArkMC, BubbleUPnP, Pixel Media, and 2Player 2.0. Windows Open Windows Media Player Right-click on music file and choose Linksys Range Extender. This list of supported media players is subject to change with the release of new software or mobile apps. Windows users can stream music with Windows Media Player12. Mac users can stream music with proprietary software or the SofaPlay app.. Android users can stream music with MediaHouse, UPnPlay, Skifita, ArkMC, BubbleUPnP, Pixel Media, and 2Player 2.0. IOS devices including iPhone, iPad or iPod can stream music with proprietary software or other apps such as, , ArkMC, Smartstor Fusion, , Mconnect, and DK UPnP/DLNA. The extender supports MP3, FLAC, WAV, WMA and AAC file formats, as long as those formats are supported by the device and app doing the streaming. The 3.5mm stereo port supports earphones and powered speakers. How to access the browser-based utility After setting up the extender use the extenders browser-based utility to change any settings. On a computer or device that is connected to your range extender, open any browser

(Internet Explorer, Chrome, Firefox, Safari, etc.), and enter extender.linksys.com in the address bar. You will be prompted to enter a user name and password. If you did not change them during setup, leave the user name blank and enter admin in the password field. If you customized the SSID and password, enter those credentials. If you are connected to your local network, but not to the range extender, you will need to enter the range extenders IP address in your browser to access the extenders settings. TIP If you are unable to access the range extenders settings, do one of the following:

Find the range extenders IP address by going to your routers administration page and looking for the range extender under connected devices. Or Windows XP:

1. Enable UPnP:

a) Click Start, Control Panel, Add or Remove Program, then click Add/Remove Windows Components. b) Select Network Services, then click Details. c) Select UPnP User Interface, then click OK. 2. Open Windows Explorer. Click My Network Places on the left panel. 3. Look for the RE6700 icon on the right panel. (You might be required to change the firewall settings to allow the display of networked computers. Refer to your operating systems help for instructions.) Windows 8, Windows 7, or Vista:

1. Open Windows Explorer (File Explorer in Windows 8). Click Network. Look for the RE6700 icon on the right panel. (You might be required to change the firewall settings to allow the display of networked computers. Refer to your operating systems help for instructions.) 2. Right-click the RE6700 icon. Click Properties. Click on the address link in Device webpage. Mac OS X:

1. Open Safari. Be sure that Bonjour is included in the Bookmarks menu and Favorites bar. a. Go to Safari Preferences > Advanced and be sure each Bonjour box is selected. 2. Find Bonjour in the Bookmarks menu or Favorites bar and choose Linksys Range Extender. If you have changed your network name and password, choose the network name and enter the password you created. Using range extender settings Click Help on the right side of the screen for additional information on the screens options. Changes to settings will not be effective until you click Save at the bottom of the screen. You also can click Cancel to clear any changes. Using Wi-Fi Protected Setup Wi-Fi Protected Setup makes it easy to connect your extender to your network, and connect other devices to your network through the extender. Wi-Fi Protected Setup light activity

<WPSButtonOnly.PNG>

WPS Light Status/ description Solid (10 seconds) Blinking slowly (two minutes) Blinking quickly (two minutes) WPS connection was successful WPS connection in process When WPS cannot establish connection or encounters a problem Fix: wait a few seconds after LED stops blinking and try again Connecting the extender to an existing access point If your access point or router supports it, you can use Wi-Fi Protected Setup to connect the range extender to the access point or router. Log in to the browser-based utility and click on WPS in the left navigation bar. Choose from the setup methods below to connect the extender. NOTE If you have an access point or a router that does not support Wi-Fi Protected Setup, note the wireless settings, and then manually configure the extender. Connecting with the Wi-Fi Protected Setup Button Use this method if your router or access point has a Wi-Fi Protected Setup button

. 1. Press the Wi-Fi Protected Setup button on the extender. If you have a dual-band router you will do this again to extend the second network. The 2.4 GHz band will be extended first. 2. Click the Wi-Fi Protected Setup button on the routers Wi-Fi Protected Setup screen (if available), OR press and hold the Wi-Fi Protected Setup button on the router for one second. When the connection is complete, the Wi-Fi Protected Setup light on the extender will be solid. 3. If you used the extenders Wi-Fi Protected Setup screen, click OK in that screen within two minutes. TIP You can also access WPS in the browser-based utility by clicking WPS in the left navigation bar. Connecting with the range extenders PIN The Wi-Fi Protected Setup PIN (Personal Identification Number) can be found on the product label on the back of the extender. You can use this method only if your routers administration utility has a Wi-Fi Protected Setup menu. 1. Enter the extenders PIN into the appropriate field on the routers Wi- Fi Protected Setup screen. Click Register. When the connection is complete, the Wi-Fi Protected Setup light on the extender will be solid. 2. Click OK. Connecting devices to your network through the extender Choose from the methods below to connect devices that support Wi-Fi Protected Setup to your network. Delete the screen below NOTE Repeat the instructions for each client device that supports Wi-Fi Protected Setup. Connecting with the Wi-Fi Protected Setup Button Use this method if your client device has a Wi-Fi Protected Setup button. 1. Press the Wi-Fi Protected Setup button on the client device. 2. Click the Wi-Fi Protected Setup button on the extenders Wi-Fi Protected Setup screen, OR press and hold the Wi-Fi Protected Setup button on the side of the extender for one second. When the connection is complete, the Wi-Fi Protected Setup light on the extender will be solid. 3. If using the extenders Wi-Fi Protected Setup screen, be sure to click OK within two minutes or you will have to start over. Connecting with the client devices PIN Use this method if your client device has a Wi-Fi Protected Setup PIN (Personal Identification Number). 1. Enter the PIN from the client device in the field on the extenders Wi-Fi Protected Setup screen. 2. Click Register on the extenders Wi-Fi Protected Setup screen. When the connection is complete, the Wi-Fi Protected Setup light on the extender will be solid. 3. Click OK on the extenders Wi-Fi Protected Setup screen within two minutes or you will have to start over. Connecting with the extenders PIN Use this method if your client device asks for the extenders PIN. 1. On the client device, enter the PIN listed on the extenders Wi-Fi Protected Setup screen. (It is also listed on the product label on the back of the extender.) When the connection is complete, the Wi-Fi Protected Setup light on the extender will be solid. 2. Click OK on the extenders Wi-Fi Protected Setup screen within two minutes. How to use Site Survey Site Survey gives a snapshot of all neighboring access points and wireless routers within range of the extender. To open the Site Survey page:

1. Log in to the browser-based utility (see How to access the browser- based utility on page 5). 2. Click the Wireless tab. Click the Site Survey page. 3. SelectTo connect to a wireless network, click the button next to the wireless network name (SSID) in the Select column, and click Connect. 4. SSIDDisplays the name of neighboring wireless networks. 5. GHzDisplays the radio band (in GHz) of the neighboring wireless networks 6. Signal StrengthDisplays the relative position of the neighboring access points by indicating the power of the wireless signal received: dot only = 25%, dot + one wave = 50%, dot + two waves = 75%, dot + three waves = 100%. If no waves are displayed, your extender is too far from the upstream access point or the signal is blocked. Try to keep the signal strength between 60% and 100% for optimum performance. 7. SecurityDisplays the mode of security in use by the neighboring APs. If a network supports Wi-Fi Protected Setup, the Wi-Fi Protected Setup icon is also displayed. To connect your extender with an access point or router in Site Survey, you will need to know the password or passphrase of the network on that device. 1. Select the network name (SSID) that you want to repeat with your extender by clicking the corresponding button in the Select column. 2. Click Connect. When prompted, enter the password or passphrase used to secure your wireless network. The type of security information required in this screen must match your access point or routers wireless security settings. TIP: For dual-band networks, be sure to connect to both bands, 2.4 GHz and 5 GHz. 3. Click Save. Your extender wireless parameters should be configured. The wireless interface will restart, and the extender will connect to the access point or router you have chosen. __ Cross-Band Cross-Band is the simultaneous use of both bands for high-speed data transfer and uninterrupted streaming and gaming. __ Troubleshooting NOTE Your RE6700 works on 2.4GHz and 5 GHz networks. You cannot get your extender connected Check the position of your router and extender For first-time setup, you may need to place the extender closer to the router. After youve set up your extender, you can unplug it and move it to the final location. To reduce signal obstructions, try alternate locations for the router and extender. Avoid placing the router and extender near metal objects, masonry walls, and reflective surfaces such as glass or mirrors. Avoid placing the router and extender near other electronics that may cause signal interference. If youre using Wi-Fi Protected Setup to connect, wait until the Wi-Fi Protected Setup indicator stops blinking before trying to make the connection again. You cannot access your range extender To access your range extender, you must be connected to your own network. If you currently have wireless Internet access, the problem may be that you have accidentally connected to a different wireless network. For Mac instructions, see To fix the problem on Mac computers: on page 12. To fix the problem on Windows computers:

1. On your Windows desktop, right-click the wireless icon in the system tray. The icon might look different depending on which version of Windows you are running. 2. Click View Available Wireless Networks. 3. Select your network name. Click Connect. In the example below, the computer was connected to another wireless network named JimsRouter. The name of the correct network, BronzeEagle in this example, is selected. 4. If you are prompted to enter a network key, type your password (Security Key) into the Network key and Confirm network key fields. Click Connect. You should now be able to access the range extenders browser-based utility. To fix the problem on Mac computers:

1. In the menu bar across the top of the screen, click the Wi-Fi icon. Linksys Connect has automatically assigned your network a name. In the example below, the computer was connected to another wireless network named JimsRouter. The name of the Linksys E-Series network, BronzeEagle in this example, is selected. 2. Select the wireless network name of the router you want to connect to. 3. Type your wireless network password (Security Key) into the Password field. Click OK. You should now be able to access the range extenders browser-based utility. You have intermittent connection problems Plug in the range extender midway between your router and the area without Wi-Fi. Be sure you have at least 50% of your routers Wi-Fi signal at that point on the device you used for setup. Specifications RE6300/RE6400 Model Name Model Description Model Number Standards Ports Buttons LEDs Antennas Wireless Security Linksys RE6300/RE6400 Dual-band Wireless-AC Range Extender RE6300/RE6400 IEEE 802.11ac, 802.11a, 802.11n, 802.11g, 802.11b, 802.3u Gigabit Ethernet, audio Reset, Wi-Fi Protected Setup, Power

(European model only) Power/Wi-Fi Protected Setup, Ethernet (link, activity) 2 external (non-detachable) Wi-Fi Protected Access 2 (WPA2), Wi-Fi Protected Access (WPA), WEP Security Key Bits Up to 128-bit encryption Environmental Dimensions Weight Power Certification 2.64 x 1.49 x 4.13 (67 x 38 x 105 mm) 5.12 oz (145 g) 12VDC/1.0A FCC, ICES-003, RSS210, CE, Wi-Fi (IEEE 802.11a/b/g/n), WPA2, WMM, Wi-Fi Protected Setup Operating Temperature 32 to 104F (0 to 40C) Storage Temperature

-4 to 140F (-20 to 60C) Operating Humidity 10 to 80% noncondensing Storage Humidity 5 to 90% noncondensing Specifications are subject to change without notice. Visit linksys.com/support for award-winning 24/7 technical support BELKIN, LINKSYS and many product names and logos are trademarks of the Belkin group of companies. Third-party trademarks mentioned are the property of their respective owners. Licenses and notices for third party software used in this product may be viewed here: http://support.linksys.com/en-us/license. Please contact http://support.linksys.com/en-us/gplcodecenter for questions or GPL source code requests. 2015 Belkin International, Inc. and/or its affiliates. All rights reserved. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

-

-

-

-

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 22cm between the radiator &

your body. Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only. Industry Canada statement:

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Caution :

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-

5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement:

(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

(ii) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 27cm between the radiator & your body. Dclaration d'exposition aux radiations:

Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 27 cm de distance entre la source de rayonnement et votre corps.

With internal power supply No. 1

(Brand: Amigo-PSU / Model No.: AMS151-1201500F) Report No.: 150729E01 Page 3 Report No.: 150729E01 Page 4 Report No.: 150729E01 Page 5 Report No.: 150729E01 Page 6 Report No.: 150729E01 Page 7 Report No.: 150729E01 Page 8 With internal power supply No. 2

(Brand: HON-KWANG / Model No.: HK-XX18-A12) Report No.: 150729E01 Page 9 Report No.: 150729E01 Page 10 Report No.: 150729E01 Page 11 Report No.: 150729E01 Page 12 Report No.: 150729E01 Page 13 Report No.: 150729E01 Page 14

CONSTRUCTION PHOTOS OF EUT Report No.: 150729E01 Page 1 Report No.: 150729E01 Page 2

RE6400 US/CA PRODUCT LABEL R1 5000423 0 0

. 0 4 RE6400 RE6400 RE6400 P/N: 8840-XXXXX RevA00 RE6400 US/CA PRODUCT LABEL 8840-XXXXX 2015/8/11 FCC ID : Q87-RE6400 IC : 3839A-RE6400 FCC ID Q87-RE6400, Q87-RE6300 IC : 3839A-RE6400, 3839A-RE6300

Declaration for no non-US channel operation August 12, 2015 We, LINKSYS LLC declare that the device does not support channel 12 ~ 13 in 2.4GHz band and any non-

US channels in all the operational mode(s) for the following product. FCC ID: Q87-RE6400 If you should have any question(s) regarding this declaration, please dont hesitate to contact us. Thank you!

-----------------------------------

Daniel Wesey / Director of Global Regulatory Compliance Tel: 310-751-2816 E-mail: danielw@belkin.com

Date: 2015-08-12 FCC ID: Q87-RE6400 A U T H O R I Z A T I O N L E T T E R To whom it may concern:

We, the undersigned, hereby authorize (name: Amanda Wu and Title: Senior Specialist)of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all manners relating to FCC application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by (name: Amanda Wu and Title: Senior Specialist) of BV CPS Taoyuan on our behalf shall have the same effect as acts of our own. If you have any questions regarding the authorization, please dont hesitate to contact us. Sincerely yours,

-----------------------------------

Daniel Wesey / Director of Global Requlatory Compliance Tel: 310-751-2816 E-mail: danielw@belkin.com

Request for Confidentiality Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Date: 1/28/2015 Subject:

FCC ID: Q87-RE6400 To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204,while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 2015/12/30. External Photos Internal Photos User Manual Test Setup photos It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Sincerely yours, ___________________________ Daniel Wesey / Director of Global Regulatory Compliance Tel: 310-751-2816 E-mail: danielw@belkin.com