FCC ID: PPQ-WCBN3610L 802.11 b/g/n, 1T1R 2.4G Wireless IoT Module

USER MANUAL 802.11 b/g/n, 1T1R 2.4GHz Wireless IOT Module Model Name: WCBN3610L Page 1/6 PRODUCT FEATURES WiFi operate at ISM frequency bands (2.4GHz) Compact Form Factor: 18 x 20.5 x 3.2 mm 0.1mm Bunch of UART/ SPI/ I2C interfaces for peripheral controllers Standards support: 802.11b, 802.11g, 802.11n, 802.11d, 802.11e, 802.11i Enterprise level security complying with WPA/WPA2 certification Light weight TCP/IP protocol suite One transmitter and one receiver 802.11n WLAN transceiver supports up to 150 Mbps downstream and 150 Mbps upstream PHY rates ARM Cortex-M development environment for customer applications HF/RoHS compliance Page 2/6 Frequency Range 802.11bg 2.412 ~ 2.462 GHz ENVIRONMENTAL Operating Operating Temperature: -20 to 85 C Relevant Humidity: 5-90% (non-condensing) Storage Temperature: -40 to 85 C Relevant Humidity: 5-95% (non-condensing) Page 3/6 WARNINGS FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. ISED Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

1.This device may not cause interference. 2.This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1.Lappareil ne doit pas produire de brouillage;

2.Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. ISED Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20cm de distance entre la source de rayonnement et votre corps. The transmitter module may not be co-located with any other transmitter or antenna. Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Pour les produits disponibles aux tats-Unis / Canada du march, seul le canal 1 11 peuvent tre exploits. Slection d'autres canaux n'est pas possible. This module is intended for OEM integrators under the following conditions:

1. Ensure that the end-user has no manual instructions to remove or install module. 2.This module is certified pursuant to Part 15 rules section 15.247 and RSS-247. 3.This module has been approved to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna Number Antenna 1 Brand Name Model Name Ant. Type Connector Support Max Peak Gain LITEON WCBN3610L Printed Ant Murata 2.4G 0.5 Page 4/6 4 Label and compliance information Label of the end product:

FCC The host product must be labeled in a visible area with the following " Contains FCC ID: PPQ-WCBN3610L". The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ISED This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following:

Contains transmitter module IC: 4491A-WCBN3610L or Contains IC: 4491A-WCBN3610L Contient le module d'mission IC: 4491A-WCBN3610L 5.Information on test modes and additional testing requirements This module has been approved under stand-alone configuration. OEM integrator has be limited the operation channels in channel 1-11 for 2.4GHz band. The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093/RSS-102 and different antenna configurations The information on how to configure test modes for host product evaluation for different operational conditions for a stand-alone modular transmitter in a host, versus with multiple, simultaneously transmitting modules or other transmitters in a host can be found at KDB Publication 996369 D04. OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC/ISED authorization is no longer considered valid and the FCC/IC No. cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product

(including the transmitter) and obtaining a separate FCC/ISED authorization. 6.Additional testing, Part 15 Subpart B and ICES-003 disclaimer Appropriate measurements (e.g. Part 15 Subpart B compliance) and if applicable additional equipment authorizations

(e.g. SDoC) of the host product to be addressed by the integrator/manufacturer. This module is only FCC/ISED authorized for the specific rule parts 15.247, RSS-247 listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC/ISED rules that apply to the host product as being Part 15 Subpart B/ICES-003 compliant. 7.The user manual of the end product should include:

FCC:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter. Page 5/6 ISED:

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

1.This device may not cause interference. 2.This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1.Lappareil ne doit pas produire de brouillage;

2.Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. ISED Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20cm de distance entre la source de rayonnement et votre corps. The transmitter module may not be co-located with any other transmitter or antenna. Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Pour les produits disponibles aux tats-Unis / Canada du march, seul le canal 1 11 peuvent tre exploits. Slection d'autres canaux n'est pas possible. Page 6/6

R:1mm R:1mm 15mm GPAC 1 3 m m Model:

WCBN3610L MAC:XXXXXXXXXXXX FCC ID:PPQ-WCBN3610L IC:4491A-WCBN3610L Made in China 3 15mm GPAC 1 3 m m Model:

WCBN3610L MAC:XXXXXXXXXXXX FCC ID:PPQ-WCBN3610L IC:4491A-WCBN3610L Made in China 1,ECC200 B5*5mm XXXXXXXXXXXX MAC

BD=MAC+1

(LABEL ) 50900011753D Blank 15*13mm WI-CQES-002 WCBN3610L-GPAC MM11325470D A1 Bing Li 2023.02.21

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: June 7, 2023 Ref: Attestation Statements Part 2.911(d)(7) Filing Grantee Code: PPQ LITE-ON TECHNOLOGY CORP. (the applicant) certifies that, as of the date of the filing of the application, LITE-ON TECHNOLOGY CORP. is our designated U.S. agent for service of process for the above referenced Grantee Code. LITE-ON TECHNOLOGY CORP. accepts to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The applicant further acknowledges their responsibility to inform the FCC whenever the designated agent information changes. LITE-ON TECHNOLOGY CORP. accepts the designation by the applicant as the U.S. agent to accept service of process includes, but is not limited to, delivery of any correspondence, notices, orders, decisions, and requirements of administrative, legal, or judicial process related to Commission proceedings. Designated U.S. Agent Information:

FRN: 0033411521 Name: LITE-ON TECHNOLOGY CORP. Address: 3001 Summit Avenue Ste. 400, Plano, TEXAS 75074, USA Contact Person: Joshua Winkler Tel.: (480) 422-4548 Email: Josh.Winkler@liteon.com Sincerely, Applicant U.S. Agent LITE-ON TECHNOLOGY CORP. LITE-ON TECHNOLOGY CORP. TC Wu, Director / Network Access S.B.U. Joshua Winkler Signature:

Signature:

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: June 14, 2023 FCC ID: PPQ-WCBN3610L RE: Attestation Statements Part 2.911(d)(5)(i) Filing LITE-ON TECHNOLOGY CORP. (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. RE: Attestation Statements Part 2.911(d)(5)(ii) Filing LITE-ON TECHNOLOGY CORP. (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List ( as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing covered equipment. Sincerely, Applicant Address

: LITE-ON TECHNOLOGY CORP.

: Bldg. C, 90, Chien 1 Rd., Chung-Ho, New Taipei City 23585, Taiwan Signature

Name and Job Title.

: TC Wu, Director / Network Access S.B.U. _________________________________ E-mail Tel.

: TC.Wu@liteon.com

: +886-2-2222-6181 #8301

Confidentiality Request Letter Date: June 14, 2023 Federal Communications Commission Authorization and Evaluation Division Subject: Request for confidentiality FCC ID: PPQ-WCBN3610L To whom it may concern:

Short-term Confidentiality pursuant to Public Notice DA 04-1705, and in order to comply with the marketing regulations in 47 C.F.R. 2.803 and the importation rules in 47 C.F.R. 2.1204 while ensuring that business-sensitive information remains confidential until the actual marketing of newly authorized devices, we are request the Commission grant temporary confidential treatment and not release the following attachments for routine public disclosure until 180 days after the grant date. 1. Internal Photographs 2. External Photographs 3. Users manual 4. Test Set up photos Permanent Confidentiality Pursuant to the provisions of Sections 0.457 and 0.459 of Commissions rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure indefinitely. 1. Block Diagram 2. Schematics 3. Operational Description It is our understanding that test measurement reports and correspondence during the certification review process cannot be granted confidential treatment, and such information will be available for public review once the grant of equipment authorization is issued. Sincerely, Applicant Address

: LITE-ON TECHNOLOGY CORP.

: Bldg. C, 90, Chien 1 Rd., Chung-Ho, New Taipei City 23585, Taiwan Signature

Name and Job Title.

: TC Wu, Director / Network Access S.B.U. _________________________________ E-mail Tel.

: TC.Wu@liteon.com

: +886-2-2222-6181 #8301

Modular Approval Request Letter Date: July 21, 2023 Subject: Modular Approval Attestation FCC ID: PPQ-WCBN3610L Dear Reviewer, We, Sporton International Inc., are authorized by LITE-ON TECHNOLOGY CORP., to have their 802.11 b/g/n, 1T1R 2.4G Wireless IoT Module approved under single module approval authorization. The requirements regulated in 47 CFR 15.212 have been fulfilled and clearly explained below. 1. The requirement of RF shielding: The shielding of the radio portion can be demonstrated in exhibition External Photo. 2. The requirement of buffered inputs: Buffered data inputs stage has been integrated in chip RTL8720CM 3. The requirement of power supply regulation: The part number of the power regulator is TPS562201DDCR, TLV62568DBVR. 4. The requirements of section 15.203 and 15.204(C): The requirements of antenna connector and spurious emission have been fulfilled. Please reference the exhibition Test Report. 5. The requirement of stand-alone test configuration: Please reference exhibition Test Configuration Photo for the stand-alone test configuration. 6. The requirement of labeling: The instruction on the labeling rule of the end product has been stated in the users manual of this module. Please also see the exhibition Label Sample. 7. The requirement of compliance on specific rule or operating requirements: The required FCC rule has been fulfilled and all the instructions for maintaining compliance has been clearly stated in the Users Manual. 8. The requirement of RF exposure: Please refer exhibition RF Exposure for the compliance of MPE and SAR RF exposure rule. Please do not hesitate to contact me for any questions of this request letter. Thank you. Signature

_________________________________ Name and Job Title.

: Leo Huang, VP E-mail

: leohuang@sporton.com.tw

Letter of Authorization Date: June 14, 2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Product Certification Representative Authorization Letter FCC ID: PPQ-WCBN3610L Product Name: 802.11 b/g/n, 1T1R 2.4G Wireless IoT Module To whom it may concern:

We the undersigned, hereby authorize following person to act as our agent in the preparation of an application for equipment authorization to the FCC Rules and Regulations. Sporton International Inc. Address

No.52, Huaya 1st Rd., Guishan Dist., Taoyuan City 333, Taiwan (R.O.C.) Name

: Leo Huang Job Title : VP e-mail

: Leohuang@sporton.com.tw We further certify that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002(b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Applicant Address

: LITE-ON TECHNOLOGY CORP.

: Bldg. C, 90, Chien 1 Rd., Chung-Ho, New Taipei City 23585, Taiwan Signature

Name and Job Title.

: TC Wu, Director / Network Access S.B.U. _________________________________ E-mail Tel.

: TC.Wu@liteon.com

: +886-2-2222-6181 #8301