USERS MANUAL 802.11b/g/n 2T2R Wireless LAN USB Module WN4646L ICM S.B.U. LITE-ON Technology Corporation 11F, 392, Ruey Kuang Road, Neihu, Taipei 11492, Taiwan, R.O.C. Page 1/9 PRODUCT FEATURES Operate at ISM frequency Band (2.4GHz) IEEE Standards Support, 802.11b, 802.11g and 802.11n CMOS MAC, Baseband PHY, and RF in a single chip for IEEE 802.11b/g/n compatible WLAN Complete 802.11n MIMO solution for 2.4GHz band Complies with USB Specification 2.0, support Full-speed(12Mbps) and High-Speed(480Mbps) Enterprise level security supporting: IEEE 802.11i (WPA, WPA2). Open shared key and pair-wise key authentication services Wi-Fi Direct supports wireless peer to peer applications Support 20MHz/40MHz bandwidth transmission Support 2 transmission and 2 receiving, transmission rate can up to 300Mbps
(Physical Rate) in downstream and upstream Support Wake-On-WLAN via magic packet and wake-up frame RoHS compliance Low Halogen compliance Page 2/9 PRODUCT SPECIFICATIONS MAIN CHIPSET Realtek RTL8192FC FUNCTIONAL SPECIFICATIONS Wi-Fi Function Standard Bus Interface IEEE802.11b; IEEE 802.11g; IEEE 802.11n USB 2.0 802.11b:
802.11g:
802.11n:
802.11b:
802.11g:
802.11n:
Data Rate 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps MCS 0 to 7 for HT20MHz MCS 0 to 7 for HT40MHz Media Access Control CSMA/CA with ACK Modulation Techniques Network Architecture Operation Channel Frequency Range CCK, DQPSK, DBPSK 64QAM, 16QAM, QPSK, BPSK 64QAM, 16QAM, QPSK, BPSK Ad-hoc mode (Peer-to-Peer) Infrastructure mode 2.4GHz 11: (Ch. 1-11) United States 13: (Ch. 1-13) Europe 14: (Ch. 1-14) Japan 802.11bg 2.400 ~ 2.4835 GHz Transmit Output Power - single chain @ant;
Tolerance: 1.5dBm@2.4GHz 2.4GHz 802.11b Tgtpwr
(dBm) 2Mbps 16 1Mbps 16 5.5Mbps 16 11Mbps 16 802.11g Tgtpwr
(dBm) 802.11n HT20 Tgtpwr
(dBm) 6~24Mbps 15 36Mbps 15 48Mbps 15 54Mbps 15 MCS0 MCS1 MCS2 MCS3 MCS4 14 14 14 MCS5 MCS6 MCS7 14 14 Page 3/9 14 14 14 802.11n HT40 Tgtpwr
(dBm) MCS0 MCS1 MCS2 MCS3 MCS4 14 14 14 14 14 14 MCS5 MCS6 MCS7 14 14 Receiver Sensitivity Frequency Band Rate 2.4G 11b-1M 11b-11M 11g-6M 11g-54M 11n-HT20 MCS0 11n-HT20 MCS7 11n-HT40 MCS0 11n-HT40 MCS7 Condition PER < 8%
PER < 8%
PER < 10%
PER < 10%
PER < 10%
PER < 10%
PER < 10%
PER < 10%
1x1(1SS)
(dBm)
-92
-85
-90
-71
-90
-70
-87
-67 Security WEP 64&128 bit, WPA, WPA-PSK, WPA2, WPA2-PSK, WPS, IEEE 802.1X, IEEE 802.11i Operating Voltage 5 V 10% I/O supply voltage OS Supported Microsoft Windows; Linux based Power Consumption Test Condition:
- Operate at HT40
- File Transmission Mode TX RX Associated Idle Standby Average 2.4GHz 282mA 175mA 15mA 13mA Peak 2.4GHz 648mA 566mA Antenna Type Dual Metal Antennas Page 4/9 RECOMMENDED OPERATION CONDITIONS Symbol Rating VCC 5V Supply Voltage VDD33 VDD10 3.3V I/O Supply Voltage 1.05V Core Supply Voltage DC CHARACTERISTICS VIL VIH VOL VOH Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage RESET TIMING SPEC Min 4.5 3.0 0.95
2.0 0 2.97 Typ 5 3.3 1.05 Typ 0 3.3
Max Units 5.5 3.6 1.15 0.9 3.6 0.33 3.3 V V V V V V Symbol Parameter in Max Units Symbol Ton TPOR Min 0.25
Typ 1.5 2 Max Units 5 10 ms ms Page 5/9 PIN ASSIGNMENT Pin. Pin Define
+5VCC
+5VCC USB_D-
USB_D+
GND RESET#
WoWLAN#
GND 1 2 3 4 5 6 7 8 Description 5V source 5V source USB Data-
USB Data+
Ground System reset RTL8192FC, low active Wake up system via wi-fi, low active Ground Status YES YES YES YES YES YES YES YES Page 6/9 Worldwide Channels 1-13 with active scan EEPROM INFORMATION Reg Domain Vendor ID Device ID 0x20 0x0BDA 0xF192 ENVIRONMENTAL OPERATING Operating Temperature: 0 to 70 C (32 to 158 F) Relative Humidity: 5-90% (non-condensing) STORAGE Temperature: -25 to 75 C (-13 to 167 F) Relative Humidity: 5-95% (non-condensing) Page 7/9 WARNINGS Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This module compy with the requirement of the following standards 47 CFR FCC Part 15.247 This module has been approved to operate with the antenna types listed below, with the maximum permissible gain indicated. Frequency Band 2400-2483.5MHz 2400-2483.5MHz Antenna Type Model Number Gain(dBi) PIFA PIFA RFMTA200700NNLB002 RFMTA200700NNLB002 2.48
-0.29 This module has been approved under stand-alone configuration. OEM integrator has be limited the operation channels in channel 1-11 for 2.4GHz band. The separate approval is required for all other operating configurations, including portable Page 8/9 configurations with respect to Part 2.1093 and different antenna configurations The information on how to configure test modes for host product evaluation for different operational conditions for a stand-alone modular transmitter in a host, , versus with multiple, simultaneously transmitting modules or other transmitters in a host can be found at KDB Publication 996369 D04 Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment authorizations (e.g. SDoC) of the host product to be addressed by the integrator/manufacturer. This module is only FCC authorized for the specific rule parts 15.247 listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host product as being Part 15 Subpart B compliant. The user manual of the end product should include Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. Label of the end product:
PPQ-WN4646L". The host product must be labeled in a visible area with the following " Contains FCC ID:
The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Page 9/9