USER MANUAL BLE Bluetooth Module WB100N Version 1.1 Author: Kaysa Lee Date 2017/01/06 2017/03/22 Author Kaysa Lee Kaysa Lee Change List Preliminary IC use 1802 and update features Change History Revision Version 1.0 Version 1.1
* This document contains confidential proprietary information and is property of LTC. The contents of this document should not be disclosed to unauthorized persons without the written consent of LTC. WB100N Specification Page 1/9 LTC Network Access Confidential 2017/9/19 CONTENT PRODUCT FEATURES .................................................................................................................... 3 PRODUCT SPECIFICATIONS ........................................................................................................ 3 MAIN CHIPSET ....................................................................................................................................... 3 FUNCTIONAL SPECIFICATIONS ............................................................................................................... 3 PRODUCT PICTURE ........................................................................................................................ 5 PIN ASSIGNMENT ............................................................................................................................ 6 FCC WARING STATEMENT .......................................................................................................... 8 WB100N Specification Page 2/9 LTC Network Access Confidential 2017/9/19 Product Features LiteON BLE Module WB100N nRF51802 Bluetooth Low Energy 14.3*14.3mm 4.0 4.2 Secure Connection MCU UART CPU APP MCU AT UARTTTL AT 115200bps MAC ibeacon 1030 class II 6Kbyte/s 1.83.6V3.3V typical 14.3*14.3mm
-40C85C :*-25C *
Product Specifications MAIN CHIPSET Nordic nRF51802 FUNCTIONAL SPECIFICATIONS 2.4 GHz transceiver
-91 dBm sensitivity in Bluetooth low energy mode WB100N Specification Page 3/9 LTC Network Access Confidential 2017/9/19 250 kbps, 1 Mbps, 2 Mbps supported data rates TX Power -20 to +4 dBm in 4 dB steps TX Power -35 dBm Whisper mode 13 mA peak RX, 10.5 mA peak TX (0 dBm) 10 mA peak RX, 8 mA peak TX (0 dBm) with DC/DC RSSI (1 dB resolution) ARMR Cortex-M0 32 bit processor Serial Wire Debug (SWD) S100 series SoftDevice ready Memory 256 kB embedded flash program memory 16 kB RAM On-air compatibility with nRF24L series Flexible Power Management Supply voltage range 1.8 V to 3.6 V 7.7 s wake-up using 16 MHz RCOSC 0.6 A at 3 V OFF mode 1.2 A at 3 V in OFF mode + 1 region RAM retention 3 A at 3 V ON mode, all blocks IDLE 8/9/10 bit ADC - 8 configurable channels 31 General Purpose I/O Pins One 32 bit and two 16 bit timers with counter mode SPI Master/Slave Low power comparator Temperature sensor Two-wire Master (I2C compatible) UART (CTS/RTS) CPU independent Programmable Peripheral Interconnect(PPI) Quadrature Decoder (QDEC) AES HW encryption RealTimer Counter (RTC) WB100N Specification Page 4/9 LTC Network Access Confidential 2017/9/19 PRODUCT PICTURE Module:
WB100N Specification Page 5/9 LTC Network Access Confidential 2017/9/19 PIN ASSIGNMENT PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 Name/Function VDD/Power supply General purpose I/O pin General purpose I/O pin General purpose I/O pin General purpose I/O pin General purpose I/O pin General purpose I/O pin General purpose I/O pin General purpose I/O pin General purpose I/O pin General purpose I/O pin General purpose I/O pin General purpose I/O pin Remark P0.30 P0.00 P0.01 P0.02 P0.03 P0.04 P0.05 P0.06 P0.07 P0.08 P0.09 P0.10 WB100N Specification Page 6/9 LTC Network Access Confidential 2017/9/19 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 General purpose I/O pin General purpose I/O pin General purpose I/O pin General purpose I/O pin General purpose I/O pin General purpose I/O pin SWDIO nRESET/System reset (active low). Also hardware debug and flash programming I/O. SWDCLK/Hardware debug and flash programming I/O. General purpose I/O pin General purpose I/O pin General purpose I/O pin General purpose I/O pin NC NC ANT/Differential antenna connection (TX and RX) GND/Ground (0 V) GND/Ground (0 V) General purpose I/O pin General purpose I/O pin General purpose I/O pin General purpose I/O pin General purpose I/O pin General purpose I/O pin General purpose I/O pin General purpose I/O pin General purpose I/O pin VDD/Power supply P0.11 P0.12 P0.13 P0.14 P0.15 P0.16 P0.17 P0.18 P0.19 P0.20 P0.21 P0.22 P0.23 P0.24 P0.25 P0.26 P0.27 P0.28 P0.29 WB100N Specification Page 7/9 LTC Network Access Confidential 2017/9/19 FCC WARING STATEMENT FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAUTION:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference and
(2) This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. IMPORTANT NOTE:
The module is limited to OEM installation ONLY 1. We hereby acknowledge our responsibility to provide guidance to the host manufacturer in the event that they require assistance for ensuring compliance with the Part 15 Subpart B requirements. WB100N Specification Page 8/9 LTC Network Access Confidential 2017/9/19 2. The host manufacturer is responsible for additional testing to verify compliance as a composite system. When testing the host device for compliance with the Part 15 Subpart B requirements, the host manufacturer is required to show compliance with the Part 15 Subpart B while the transmitter module(s) are installed and operating. The modules should be transmitting and the evaluation should confirm that the modules intentional emissions are compliant (i.e. fundamental and out of band emissions) with the Radio essential requirements. The host manufacturer must verify that there are no additional unintentional emissions other than what is permitted in the Part 15 Subpart B or emissions are complaint with the Radio aspects. This module is intended for OEM integrator. The OEM integrator is still responsible for 1. ensuring that the end-user has no manual instructions to remove or install module 2. the FCC compliance requirement of the end product, which integrates this module. 3. Appropriate measurements(e.g. 15 B compliance) and if applicable additional equipment authorizations (e.g. Verification, Doc) of the host device to be addressed by the integrator/manufacturer. 4. The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations 5. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. 6. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. The user manual of the end product should include In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than the palm of the hand, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID:
PPQ-WB100N ". If the size of the end product is larger than the palm of the hand, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. WB100N Specification Page 9/9 LTC Network Access Confidential 2017/9/19