Bluetooth Module WB110C (WB110C-IW) Users Manual Federal Communication Commission Interference Statement
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
USERS MANUAL OF THE END PRODUCT:
The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID: PPQ-WB110C/PPQ-WB110CIW ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Hereby, Lite-On, declares that this device is in compliance with the essential requirement and other relevant provisions of the R&TTE Driective 1999/5/EC.
, CC XX xx YY yyy Z z W
/ The module will only be sold to and installed by appointed OEM or ODM installers. 1 INTRODUCTION 1.1 WB110C (-IW) Bluetooth Module WB110C (-IW) Bluetooth Module uses CSR BC4 ROM A07 chip which fully qualified Bluetooth v2.1+EDR system. The features of Bluetooth V2.1 is improved pairing, improved security, lower power consumption, and near field communication technology. With Enhanced Data Rate (EDR mode), the rate up to 2Mbps and 3Mbps. This module controls in USB interface and is compliance with USB v1.1 and compatible with USB v2.0. It being used to integrate with systems such as NB, desk topetc. With Bluetooth module embedded inside, a system could provide the ability to link with peripherals wirelessly through Bluetooth function. 1.2 How to works The module refers to a worldwide Bluetooth SIG standard. Before transfer data to each other, two BT modules must establish a connection. One device requests the connection with another and the second one accept it. Then user can use different data transfer function wirelessly between two Bluetooth devices. 1.3 Product Features Bluetooth V2.1+EDR system (backwards compatible with v1.1/1.2
/2.0devices) Class II (Max +4 dBm, 2.5mW) 4Mbits integral ROM Enhanced Data Rate (EDR) compliant for both 2Mbps and 3Mbps modulation modes Integrated Printed Antenna Tiny Form Factor Support OS: Windows based OS Full-speed Bluetooth operation with full Piconet support Scatternet support Extended SCO (eSCO) support 1.8V core, 1.7 to 3.6V I/O Low-power 1.8V operation (integral 1.8V regulator) USB and dual UART ports to 3Mbaud Support for 802.11 coexistence RoHS Compliant Standards Interface Form Factor Data Rate Bluetooth V2.1 + EDR USB ACES 87213-0800G connector Data Rate: 1 Mbps, 2Mbps and Up to 3Mbps 2.402~2.480 GHz 2 1 dBm Class 2 Device Frequency Range Transmit Output Power Receiver Sensitivity
< 0.1% BER at -78 dBm Operating Voltage 3.3 V DC +/- 10%
OS supported Windows based OS Bluetooth stack CSR HCI stack Power Consumption TX mode: 58mA RX mode: 46mA Stand by mode: 12mA Up to 10m (Varies depending on operating environment) *
Printed Antenna Antenna Type Coverage 1.4 System Requirements System should meet the following items:
-MB supports matched USB connector
-Windows XP/Vista
-60MB free disk for installing the Toshiba stack 1.5 WB110C(-IW) Product View 2 Using the Bluetooth Utility