This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
Safety Precautions Read this guide carefully and keep it for future reference. Follow all instructions for safe use and handling of the product. Use the camera within given temperature, humidity and voltage levels noted in the cameras specifications. Do not disassemble the camera. Do not point the camera directly at the sun or a source of intense light. Periodic cleaning may be required. Use a damp cloth only. Do not use any harsh, chemical-based cleaners. Troubleshooting Problem Cannot set up camera No picture / signal Dimensions Disclaimers The camera is rated for indoor use only. Do not mount the camera outdoors. This camera includes an Auto Mechanical IR Cut Filter. When the camera changes between Day/
Night viewing modes, an audible clicking noise may be heard from the camera. This clicking is normal, and indicates that the camera filter is working. Audio recording without consent is illegal in certain jurisdictions. Lorex Corporation assumes no liability for use of its products that does not conform with local laws. 4.2 107mm 3.4 / 86mm No audio Person detection not working Camera stuck downwards Solution Ensure your mobile device and the camera are within range of your Wi-Fi router. Ensure the LED indicator on the camera is flashing green before beginning setup. Ensure the LED indicator on the camera is glowing steady green. See LED Behavior section for details if otherwise. Ensure the camera is properly connected to power using the included USB power adapter. Try repositioning the camera, router, or both to improve signal strength. spiderwebs. Clean the lens with a soft, clean cloth. Remove the vinyl cover on the camera lens. Ensure audio function on camera is turned on. Ensure audio is turned up on viewing device. Ensure you have enabled Person Detection in the Device Settings screen of the Lorex Home app. See Overview of Lorex Home App for details. Turn off Privacy Mode in Device Settings on the Lorex Home app. See Overview of Lorex Home App for details. Picture is not clear Check the camera lens for dirt, dust, Resources LED Behavior Package Contents Need Help?
Visit us online for up-to-date software and complete instruction manuals See table below for definitions of cameras LED behaviors:
Meaning Operating correctly. Ready for connection.
(flashing rapidly) Mobile device is attempting to connect to the camera. Device malfunction. Try resetting the camera (see Camera Overview for details) and repeating the setup. Network connection failed. Try resetting the camera
(see Camera Overview for details) and repeating the setup. Behavior
(steady)
(flashing)
(steady)
(flashing)
(flashing rapidly) microSD error. Try removing and re-inserting the included microSD card, or try a different card.
(alternating) Firmware upgrade in progress. FCC Notice THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. 1 2 3 4 Visit lorex.com Search for the model number of your product Click on your product in the search results Click on the Downloads tab Copyright 2019 Lorex Corporation As our products are subject to continuous improvement, Lorex reserves the right to modify product design, specifications and prices, without notice and without incurring any obligation. E&OE. All rights reserved. W261AQ_QSG_EN_R2.indd 1 W261AQ_QSG_EN_R2.indd 1 2K QHD Smart Indoor WI-FI PT Security Camera Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. ce matriel est conforme aux limites de dose d'exposition aux rayonnements, FCC / CNR-102 nonce dans un autre environnement.cette eqipment devrait tre install et exploit avec distance minimale de 20 entre le radiateur et votre corps. W462AQ-Z Quick Start Guide lorex.com Bracket 3 3 Camera Power Accessories Mounting Kit ATTENTION:
A REGULATED UL / CSA APPROVED power supply is REQUIRED for use with this camera (included). Use of a non-regulated, non-conforming power supply can damage this product and voids the warranty. A B D Camera Overview A B C Status LED Microphone Reset: Press and hold until the chime sounds to reset the camera. microSD slot: microSD card pre-inserted (expandable up to 256GB, microSD class 10 or higher). Speaker Ethernet: For service only. Power: Connect the included USB power adapter. E F G D E F C G W261AQ_QSG_EN_R2 2019-11-19 3:50:16 PM 2019-11-19 3:50:16 PM STEP 1: Connecting to Lorex Home STEP 2A: Installation Tips Overview of Lorex Home App Connect to the camera using the free Lorex Home app on your iPhone or Android phone. To connect your camera to Lorex Home:
To ensure the best possible wireless performance, it is recommended to keep the following installation tips in mind when choosing a location for the camera:
Place the camera as close to your Wi-Fi router or access point as 1. Connect the camera cable to the included USB adapter and plug into a possible. Reduce the number of obstructive materials between the camera and the router or access point. Concrete, brick, metal and wood are the most common materials in your house that can cause poor signal strength. Back to previous screen Overview of the live viewing screen and controls in the Lorex Home app. For complete instructions on using the app, see the Lorex Home app manual on your product page at lorex.com. Device name Device settings nearby outlet. 2. Download and install the free Lorex Home app from the App Store or Google Play Store. 3. Tap the Lorex Home icon to launch the app. Tap Sign up, then follow the on screen prompts to create an account. Record your account details below:
Email:
Account Password:
4. Once the status LED on the camera is flashing green and the startup chime sounds, tap +. 5. Scan the QR code on the bottom of the camera using your mobile devices camera. NOTE: If your mobile device cannot scan the QR code, tap Manually enter Device ID. 6. Create a secure password for the camera. Record your camera password below:
Camera Password:. 7. Select your Wi-Fi network from the list, then enter the password to connect your camera to the Internet. 8. Once the status LED on the camera is solid green, tap Next to add the camera to your Lorex Home account. 9. Set a name for the camera and configure date & time preferences, then tap Complete to finish the setup. STEP 2B: Ceiling Mounting (Optional) The camera is ready at this point to be placed on any surface and begin monitoring if you would like to keep the placement of your camera flexible. You also have the option to mount the camera to an indoor ceiling using the included mounting accessories. Manual recording Other electronic devices such as microwaves, TVs, cordless phones, and baby monitors can cause signal interference. It is recommended to install the camera as far away from these devices as possible. To mount the camera:
1. Mark the cameras mounting position using the included mounting template. 2. Drill holes where marked on the mounting template. accessories. NOTE: Insert the optional plastic mounting anchors if needed. 3. Remove the mounting plate from the camera base and position the holes over the mounting points. 4. Attach the mounting plate to the mounting surface using the included mounting screws. 5. Twist the camera base onto the mounting plate to secure it to the mounting surface. Adjust the cameras position as needed. Mounting surface Mounting plate Plastic anchors Mounting screws Play back recorded video Snapshot 2-way audio: tap to speak, tap again to disable Pan-Tilt controls**
Pause / Play Viewing modes Streaming quality*
Mute /
Unmute Fullscreen 6. If you are installing the camera on a ceiling, use the Image Rotation feature on the Device Settings screen of the Lorex Home app to flip the camera image (see Overview of Lorex Home App for details).
* Change the streaming quality to SD (Standard Definition) to conserve bandwidth while watching live video. This will not impact the quality of recorded video.
** Enable Smart Tracking (beta) on the Device Settings screen to have the camera follow and adjust to one moving object in the scene. Tracking varies depending on the speed of motion. W261AQ_QSG_EN_R2.indd 2 W261AQ_QSG_EN_R2.indd 2 W261AQ_QSG_EN_R2 2019-11-19 3:50:17 PM 2019-11-19 3:50:17 PM