FCC ID: 2AKIT-AK022 Smart Wall Switch

Smart Wall Switch (No Neutral, Double Rocker) Product Profile Before you install This product is only used to replace a single pole switches rather than a 3-way switch. Push Button Short Press Once: Turn on/off Long Press for 5s: Reconnect Quick Press 3 Times: Effective Range Test Indicator Light

*

This product requires a compatible hub. Some features require a specific hub. For the detailed list, please visit: www.aqara.com/support Warning 1. A certain amount of electrical knowledge is required to install a smart wall switch. For your safety, we recommend that you ask a qualified electrician to help you install it;

Smart Wall Switch (No Neutral, Double Rocker) 2. This product is for indoor use only; do not use it in humid environment;

3. Do not install this product near a heat source. Installation Visit www.aqara.com/support for more information. 1. Turn off power at circuit breaker or fuse box and test that power is off before wiring. (Please switch the light several times to make sure that the power has been disconnected) OFF OFF OFF OFF OFF ON ON ON OFF OFF OFF OFF OFF ON ON ON ON ON Switch de pared inteligente (sin neutro, basculante doble) Antes de la instalacin Verifique la compatibilidad 2. Retire el switch que se vaya a sustituir y marque el cable con la etiqueta de cables para identificar el cable correspondiente en la instalacin. Perfil del producto Este producto solo puede sustituir switches de control sencillo en lugar de switches de doble control. Botn Pulsacin corta: encender/apagar Pulsacin larga durante cinco segundos: volver a conectar Tres pulsaciones rpidas:

prueba de alcance efectivo Luz indicadora Installation Visitar en www.aqara.com/support para obtener ms informacin. 1. Desconecte la alimentacin del switch que se vaya a sustituir antes de la instalacin (apague y encienda la luz varias veces para comprobar que se ha desconectado la alimentacin).

*

Este producto debe utilizarse con un dispositivo con funcionalidad de puerta de enlace. Algunas funciones requieren compatibilidad con modelos de puerta de enlace especficos. Para una lista detallada, visite: www.aqara.com/support Advertencia 1. La instalacin de un switch inteligente requiere ciertos conocimientos en materia de electricidad. Para su seguridad personal, se recomienda pedir ayuda a un electricista cualificado para la instalacin. 2. 3. Este producto ha sido diseado exclusivamente para uso en interiores;

no lo utilice en un entorno hmedo. No instale el producto cerca de una fuente de calor. OFF OFF OFF OFF OFF ON ON ON OFF OFF OFF OFF OFF ON ON ON ON ON Tierra normalmente de color verde. Neutro Obligatorio, pero no siempre presente. Lnea/Carga Obligatorio, normalmente de color negro, siempre presente. 3. Instale el switch de pared inteligente y conecte el cable segn sea necesario;

Tierra normalmente de color verde. Neutro Obligatorio, pero no siempre presente. Lnea/Carga Obligatorio, siempre presente. 4. Extraiga la cubierta de superficie y fije el switch a la caja de interruptores con tornillos. (Nota: no apriete demasiado los tornillos para no deformar el switch) 2. Remove the existing switch and identify the wires with wire labels. Ground Usually green. Neutral Required, but not always present, usually white. Line(Hot)/Load Required, usually black, and always present. 3. Install the smart wall switch and connect wires as required. Ground Usually green. Neutral Required, but not always present, usually white. Line(Hot)/Load Required, and always present. 4. Tuck the wires into the wall box leaving room for the smart switch. Using the screws provided, mount the smart switch to the wall box. Be careful not to crush any wires. (Note: avoid overtightening the screws.) 5. Coloque la cubierta de superficie del switch, conecte la alimentacin y controle con el botn; si el control no funciona, compruebe que las conexiones sean correctas y que se haya conectado la alimentacin; si funciona, siga los pasos a continuacin para agregar el producto. Configuracin rpida 1. Agregue el hub a la aplicacin de acuerdo con la Gua rpida del hub. 2. la pgina Add Device Abra la aplicacin, pulse + en la parte superior derecha para acceder a

(Agregar dispositivo

[accesorio]). Seleccione Switch de pared inteligente (sin neutro, basculante doble) y siga las instrucciones para agregarlo.

(Accessory)

*Si falla la conexin, acerque el switch de pared al hub, conctelo y vuelva a intentarlo. Prueba de alcance efectivo: pulse rpidamente tres veces el botn en el accesorio. Si el hub emite un mensaje de voz, significa que el accesorio y el sensor se estn comunicando correctamente. Descripcin de la luz indicadora Estado de la luz indicadora La luz azul parpadea rpidamente Luz azul fija Descripcin del estado Se est estableciendo conexin con la red Zigbee La red Zigbee funciona correctamente La luz roja parpadea rpidamente Alarma de alta temperatura La luz roja parpadea lentamente No hay conexin con la red Zigbee Especificaciones Modelo: QBKG14LM Dimensiones: 120 x 74 x 36,5 mm4,72 x 2,91 x 1,44 pulgadas) Protocolo inalmbrico: Zigbee3.0 Entrada: 120 VCA, 60 Hz Cargas mnimas: 3W/va (incandescente), 5W/va (CFL/LED), carga tpica Cargas mximas: 600W/va (incandescente), 200W/va (CFL/LED), 1/4HP (total) Temperatura de funcionamiento: 0 40C32 104F Humedad de funcionamiento: 0 95% HR, sin condensacin 5. Install the wall plate, turn main power ON at the circuit breaker, and test the switch by pressing the button;

If it doesnt work, please check: a. If the wiring is correct; b. If the power is restored. If it works, add the switch to the app following the next steps;

Manufacturer: Lumi United Technology Co., Ltd. Address: 8th Floor, JinQi Wisdom Valley, No.1 Tangling Road, Liuxian Ave, Taoyuan Residential District, Nanshan District, Shenzhen, China. Online Customer Service: www.aqara.com/support Email: support@aqara.com Quick Setup 1. Please add the Hub to the app according to the Hub Quick Start Guide. 2. Please open the app, and then tap + in the top right corner to enter Add Device (Accessory) page. Select Smart Wall Switch (No Neutral, Double Rocker), and add it according to instructions.

*If the connection fails, please move the hub closer to the switch, connect to power and try again. Effective Range Test: Quick press the button on the device 3 times. If the Hub makes voice prompts, it indicates that the device can communicate effectively with the Hub. Indicator Light Description Indicator Light Status Status Description Blue light blinks quickly Zigbee network is connecting Blue light keeps on Zigbee network works properly Red light blinks quickly Red light blinks slowly High temperature alarm Zigbee network is not connected Specification Model: QBKG14LM Dimensions: 120 x 74 x 36.5 mm (4.72 x 2.91 x 1.44 in) Wireless Protocol: Zigbee3.0 Input: 120 V AC 60Hz Min Load: 3 W/way (Incandescent), 5 W/way (CFL/LED), typical load Max Load: 600 W/way (Incandescent), 200W/way (CFL/LED), 1/4 HP Operating Temperature: 0 40C32 104F Operating Humidity: 0 95% RH, non-condensing Fabricante: Lumi United Technology Co., Ltd. Direccin: 8th Floor, JinQi Wisdom Valley, No.1 Tangling Road, Liuxian Ave, Taoyuan Residential District, Nanshan District, Shenzhen, China. Servicio de atencin al cliente en lnea: www.aqara.com/support Correo electrnico: support@aqara.com FCC ID: 2AKIT-AK022 Federal Communications Commission (FCC) compliance statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IC: 22635-AK022 IC NOTICE TO CANADIAN USERS This device complies with Industry Canada licenseexempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. This device complies with RSS247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference. This Class B digital apparatus complies with Canadian ICES003 (Cet appareil numrique de la Classe B conforme la norme NMB003 du Canada). This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Cet quipement est conforme aux limites IC d'exposition aux radiations dfinies pour un environnement non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 20 cm entre le radiateur et votre corps. Cet metteur ne doit pas tre situ ou oprant en conjonction avec une autre antenne ou metteur.

Lumi United Technology Co., Ltd Date: 2021/02/20 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Request of Class II Permissive Change Company name: Lumi United Technology Co., Ltd FCC ID: 2AKIT-AK022 FCC Part 15 Certification This is to request a Class II Permissive Change for FCC ID: 2AKIT-AK022, Originally granted on 04/11/2019 Gentlemen, The major change filed under application is:

1. Replace the low section fuse with the high section fuse. FVIN: V1.0.1 FVIN: T1 Lumi United Technology Co., Ltd 2. Replace the insurance resistance in the power supply circuit with the temperature insurance resistance. FVIN: T1 FVIN: V1.0.1 Based on these changes only radiated emissions(30MHz ~ 1GHz) and conduction emissions require retest If you have any questions regarding this application, please feel free to contact Contact name: Freddie Duan Company name: Lumi United Technology Co., Ltd Telephone: 0755-86635126 Email Address: hang.duan@lumiunited.com Signature:

Lumi United Technology Co., Ltd File Name Schematics.pdf Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2AKIT-AK022 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request permanently confidential treatment of information accompanying this application as outlined below:

Exhibit Type Schematics The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Contact name: Freddie Duan Company name: Lumi United Technology Co., Ltd Telephone: 0755-86635126 Email Address: hang.duan@lumiunited.com Signature:

Rev 11/20/07

Lumi United Technology Co., Ltd Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 2021.02.23 SUBJECT: FCC Application for FCC ID: 2AKIT-AK022 To Whom It May Concern:

We, the undersigned, hereby authorize _Walter Chen _ at _CTC Laboratories, Inc. on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by _ Walter Chen _ on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, Contact name: Freddie Duan Company name: Lumi United Technology Co., Ltd Telephone: 0755-86635126 Email Address: hang.duan@lumiunited.com Signature:

\\192.168.1.251\szctc\06 \02 RF \2021 \2 \CTC210111-034 WS-USC01\1.\1.3 \Letter\FCC Letter\POA_Letter_140225.docx