FCC ID: 2AVTG-0235TGMG IP Camera

Video Doorbell 1 1 Doorbell Appearance Front and Rear Panels Microphone Power Supply Terminal Power Supply Terminal Indicator Light Doorbell Button Indicator, button and microphone Power supply terminal Side Panel Speaker Anti-theft Screw Hole Speaker Anti-theft screw hole 1 Micro SD Card slot Reset Button Micro SD card slot Reset button Inside 1 2 2 In The Box Doorbell body Replaceable faceplate Angle adjustment bracket (horizontal) Flat bracket Angle adjustment bracket (vertical) Mounting level 3 Dual purpose screwdriver Anti-theft screw*2 Set screw for power wire*3 Set screw for securing the body to the bracket*3 Self-tapping screw (0.75)*3 Self-tapping screw

(1.26)*3 Plastic expansion bolt*3 User manual 4 3 Doorbell Installation Install Micro SD Card 1. Open the faceplate from 2. Open the Micro SD the bottom. card slot cover. 3. Insert the Micro SD card. 5 Install the Doorbell 1. Install the mounting level, and mark points on the wall for drilling according to the mounting level. 2. Drill holes on the wall, insert expansion bolts, and then insert 0.75 self-tapping screws. 6 3. Connect the power wires coming out of the wall to the terminals on the back of the doorbell with set screws.(DC 12V or AC 16~24V ) 4. Open the faceplate from the bottom. 7 5. Secure the doorbell body to the bracket using the corresponding set screws. 6. Attach the faceplate to the body from the top. 8 7. Tighten the anti-theft screws at the bottom of the device using the screwdriver. 9 Install the Bracket(Three ways) A. Install the angle adjustment bracket with 0.75 self-tapping screws. B. Install the angle adjustment bracket with 0.75 self-tapping screws. 10 C. Stack angle adjustment brackets 1Stack the vertical angle adjustment bracket on top of the horizontal angle adjustment bracket, then install the brackets onto the wall. 2 Use the supplied 1.26 self-tapping screws when stacking brackets. 11 4 Set Up Download EZLive Make sure your mobile phone has been connected to Wi-

Fi. Scan the following QR code to download and install EZLive. https://a.app.qq.com/o/simple.jsp?pkgname=com.uniview.ap p.smb.phone.en.lingyun Add Devices 1. Open EZLive, sign up an overseas account and log in. 12 2. Click in the upper right 3. Choose video doorbell corner, and select Add Wi-Fi device. Device. 13 4. Follow the instructions to prepare the device ready for configuration. 14 5. Complete configuration information and Scan the QR code on the doorbell. 15 6. A QR code will be 7. Use the camera of the Generated on the APP. doorbell to scan the QR code. When the doorbell indicator turns into steady green and you hear Network Connected, click Success. Continue. 16 8. Set DST after the device is added. 17 9. View the doorbell in the device list. 18 Doorbell Indicator Status During Setup Indicator Status Description Steady red Steady green Blinking green 1. Waiting for Wi-Fi The device is starting up Wi-Fi connection succeed configuration. 2. QR code scanned, connecting Wi-Fi. Doorbell Indicator Status After Setup Indicator Status Steady green Blinking blue Steady blue Description 1. Normal 2. Call ended Call initiated Call connected 19 Doorbell Indicator Status During Exception Indicator Status Description Blinking red 1. Wi-Fi connection failed. 2. The doorbell resetting restarting. is or The doorbell gets offline after connected to Wi-Fi. Steady yellow 20 5 Doorbell Operation Two-way Audio 21 Live View 22 Playback 23 6 Notes 1. Make sure the connected Wi-Fi is 2.4GHz. 2. Make sure your router is close to the doorbell. 3. The installation height of the doorbell is about 1.6 meters. 4. Do not install the doorbell on the metal door to avoid signal interference. 24 take attention Regulatory Compliance FCC Part 15 Please that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum 25 distance 20cm between the radiator & your body. LVD/EMC Directive 26 This product complies with the European Low Voltage Directive 2014/35/EU and EMC Directive 2014/30/EU. WEEE Directive2012/19/EU The product this manual refers to is covered by the Waste Electrical &

Electronic Equipment (WEEE) Directive and must be disposed of in a responsible manner. 27 Battery in the product complies with the European Battery Directive 2013/56/EC. For proper recycling, return the battery to your supplier or to a designated collection point. 28 Zhejiang Uniview Technologies Co., Ltd. Building No.10, Wanlun Science Park, Jiangling Road 88, Binjiang District, Hangzhou, Zhejiang, China

(310051) Email: overseasbusiness@uniview.com;

globalsupport@uniview.com http://www.uniview.com 2019 Zhejiang Uniview Technologies Co., Ltd. All

*Product specifications and availability are subject to rights reserved. change without notice. 29 Version: V1.02 BOM: 3105C00P 30

Uniview tec |? Camera 1PDB22 POWER RATING: _~16-24V, SO/6OHz, 1.08; =12V, 1.08

{AACR 1H A i HM MAC:x00n0300000K FOC ID2AVTG-0235TEMG CE x This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Matrix Network Inc Date: 04/08/2020 Communications Federal Authorization 7435 Oakland Columbia, MD. 21046

& Evaluation Mills Road, Comission, Division, Attention:

CHANG IN IDENTIFICATION Authorization OF EQUIPMENT Equipment Branch for a currently We, (Matrix 2.933(b) ID: 2AVTG-0235TGMG Per 2.933(b) 1.The original identification 2.The original grant date is 12/03/2019 3.The equipment is electrically identica construction. 4.The original test results 5.Exterior External photos with label location submitted photographs are included as attachments. Sincerely, J00

(Signature 1) Title:

On behalf of: _ Matrix Network Inc

(Company Name) Telephone:

7:J -t/5'1 -8(:::, 5 Network Inc), request to apply for a new FCC ID as established in 47CFR approved device. This application will establish a new FCC is FCC ID: 2AL8S-0235C3MR l. There is no change in design, circuitry or are applicable and representative of this changed device. in this application. and type label sample drawing are electronically T\JIF t.,-) l

(Print name)

Zhejiang Uniview Technologies Co., Ltd. Federal Communications Commission, Date: 04/08/2020 Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD. 21046 Attention: Equipment Authorization Branch CHANG IN IDENTIFICATION OF EQUIPMENT We, (Zhejiang Uniview Technologies Co., Ltd.) , declare on our sole responsibility that (Matrix Network Inc) may apply Change in FCC Identifier as established in 47CFR 2.933(b) for currently approved devices listed below. FCC ID: 2AL8S-0235C3MR Regards, By:

Title:

On behalf of:

Telephone: ______ 18106582562___________________ ___Certifcation Manager_______________________ __ Zhejiang Uniview Technologies Co., Ltd._______

(Company Name)

(Signature1) ____ Feng Xu

(Print name)

Matrix Network Inc TO: Federal Communication Commission Authorization Branch Equipment 7 435 Oakland Columbia, Mills MID 21046 Road Regarding:

FCC /D:2A VTG-0235TGMG To whom it may concern:

Date: 2020-4-8 We, the undersigned, application documents the same effect hereby for equipment relating authorization to these matters. as acts of our own. to authorize Parlam Zhan to act on our behalf in all manners including to the FCC ID above, with respect signing of all relating Any and all acts carried out by the agent on our behalf shall have We, the undersigned, FCC benefits, pursuant hereby to Section 5301 of the Anti-Drug certify that we are not subject to a denial Abuse Act of 1988, 21 U.S.C. of federal benefits, 853(a). that includes Where our agent signs the application for complying with the terms and conditions resides with Matrix Network Inc for certification on our behalf, I acknowledge that all responsibility for Certification, as specified by SGS North America, Inc., still This authorization is valid until further written notice from the applicant. -

1 f'Oc j c. Title:

Name (Printed) C..\Jl\(_) Signatur

On behalf of Company:

Matrix Network Inc Telephone:

q 7;; <-/8(.::,{c