IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions All the safety and operating instructions should be read before this product is operated. 2. Keep these instructions The safety and operating instructions should be retained 3. Heed all warnings All warnings on the appliance and in the operating instructions for future reference. should be adhered to. 4. Follow all instructions All operating and use instructions should be followed. 5. Do not use this apparatus near water The appliance should not be used near water or moisture for example, in a wet basement or near a swimming pool, and the like. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufactures 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers) that produce heat. 9. Only use attachments/accessories specied by the manufacturer. 10. Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus. When a cart or rack is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 11. Unplug the apparatus during lightning storms or when unused for long periods of time. 12. Refer all servicing to qualied personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. instructions. Bolt100 FCC ID:OR8-BOLT 100 IC:21231-BOLT100 13. WARNING: To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that objects lled with liquids, such as vases, shall not be placed on apparatus. 14. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. 15. WARNING: The battery (battery or batteries or battery pack) shall not be exposed to excessive heat such as sunshine, re or the like. 16.This lightning ash with arrowhead symbol RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR within an equilateral triangle is intended to alert the user to the presence of non-insulated dangerous voltagewithin the product s enclosure that may be of sufcient magnitude to constitute a risk of electric shock. Warning: To reduce the risk of electric shock, do not remove cover (or back) as there are no user-serviceable parts inside. Refer servicing to qualied personnel. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accom panying the appliance. 17. Correct Disposal of this product. This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling. 18. No naked ame sources, such as lighted candles, should be placed on the apparatus. 19. Replacement parts - When replacement parts are required, ensure the service technician has used replacement parts specied by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in re, electric shock or other hazards. 20. Try to install the product near a wall socket or extension cord and shall be easily accessible. 21. The highest environmental temperature suitable for this product is 0 to 35 for indoor use only . FCC and Canada EMC Compliance Iinformation Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. 1.DO NOT expose product t o extreme temperatures, moisture o r 2.DO NOT attempt to open this product for any reason. 3.DO NOT attempt to manipulate any electrical components into 4.DO NOT attempt to use if internal components have been electric shock this product exposed to liquid Package includes 1.1 Bluetooth Headphone Unit 2.1 Micro USB Charging Cable 3.3Sets Of Ear Buds (L/M/S size) one i s on the headset 4.1User Manual Manual contents 1.Specications 2.Parts 3.How to charge Bluetooth Headphone 4.How to connect Bluetooth Headphone 5.How to use Bluetooth Headphone 6.Frequently Asked Questions Parts How to Charge the Headphones 1.A rechargeable battery is built-in the Bluetooth headphones 2.Please charge at least 2 hours before the rst usuage. 3.The red indicator light will be on when the product is been charged. After fully charged, the indicator will change to blue. NOTE :
Only a 5V DC charger or computer USB port can be used as the power supply to charge this headphone. This headset is charged from a micro USB port. Specications Support HSP, HFP, A2DP,AVRCP Frequency Range Transmitting Power 2.4 GHz Class 2 Working Distance About 10 meters Charging Time about 1 hour Talk time Playback time Standby time 5-6hours 5-6 hours 180 hours Turn On the earphone:When power o ff status, press and hold the Power on button for two seconds, the indicator light ashes i n blue color. Frequently Asked Questions How to Use Bluetooth Headphones 1.Press + button to increase volume, press and hold + button to previous audio le. 2.Press - button to decrease the volume, press and hold - to next audio le 3.Press Power button to answer or hang off a calling when on a phone call 4.Press Power button to pause or start a audio le when play back audio 5.Press Power button and hold for about 2-3 seconds until the indicator ashes twice in red to turn off the Bluetooth headphone, at the same time you can hear a voice prompt, Power off How to Connect this Bluetooth Headphone with a Mobile Phone When phone is off, press and hold the Power On button for 3 seconds. The indicator 1. light will flash blue, at the same time you will hear a voice prompt. Hold the "Power On"
button for 2 more seconds. The light will flash red and blue showing that it's ready to pair. At the same time you will hear the voice prompt, Ready to pair. Turn on the Bluetooth function on your smart/mobile phone or search for the Bluetooth 2. on other devices as the ID: Bolt 100, then pair it. It will show on your mobile phone if paired successfully. You will also hear a voice prompt, your headset paired, connected. Please proceed to play audio or make hands-free call. This Bluetooth headphone can be re-connected automatically with smart phone if they have been paired before. Just press the "Power on button for 3 seconds and it will pair with the phone automatically. 3. Failure to connect to Bluetooth-
enabled devices might be caused by:
Other Bluetooth devices are paired or sync mode are interfering with your connections. Please remove other devices from the vicinity o r turn them off Static or mufed sound can b e caused by any of the following:
There are major Bluetooth obstructions between your devices and the headphone The distance o f connection is over than 10 meters or there are obstacle between this headphone and your mobile phone.