MM591050-10 Wi-Fi Module Datasheet Description initial release Author Revision Date 1.0 2016-09-27 1. Introduction ......................................................................................... 1.1Module System Block Diagram ................................................. 1.2 Module technical specifications ....................................... 2. Structure specification ...................................................................... 2.1 Module structure size .................................................................................................... 5 2.2 Hardware interface definition .................................................................................... 6 3. Wireless Specification ....................................................................... 3.1 802.11b mode................................................................................................................. 6 3.2 802.11g mode................................................................................................................. 7 3.3 802.11n HT20mode ........................................................................................................ 8 3.4 802.11n HT40mode ........................................................................................................ 9 1. Introduction MM591050-10 Wireless WIFI module is a low-power WIFI module for the Internet of Things. It supports IEEE802.11b / g / n protocol. It also embeds IPV4 / IPV6 TCP / IP, HTTP, DNS, FTP and other complete network protocols, making the terminal more reliable, convenient and easy to use. The MM591050-10 module contains a Midea MS51001 single-chip solution. the chip in software and hardware are used in low-power technology, the purpose is to lower the power consumption of the entire board, the product more competitive.At present, the module provides a complete serial interface functions and equipment to communicate, so you can through the serial port and mobile client to connect the cloud and equipment. IEEE 802.1b/g/n, 2.4Ghz ,1T1R internal antennas Green TX Low power saving technology Low power monitor mode Support 150Mbps Support PWM Full encryption supportWPS, WPA, WPA2, WAPI, WEP, TKIP Support IPV4/IPV6, TCP/IPprotocol Support HTTP, DNS, FTP and other network protocols Support AES 128/256, DES/3DES, SHA1, SHA224 and other hardware encryption 1.1 Module System Block Diagram As shown in Figure 1, MM591050-10 using the Midea MS51001 single-chip 1T1R program, the chip highly integrated CPU, PMU, RAM, Transceiver, LNA, PA, memmory, XTAL and other major parts, thus greatly reducing the machine power, Amplitude reduces the layout area. The module uses the internal antenna design in PCB, both for customers to reduce the cost of the antenna, but also eliminates the need to consider the antenna assembly space. figure 1. Module System Block Diagram 1.2 Module technical specifications Main chip Workingfrequency SupportedWIFI standard Modulation Midea MS51001 2.412GHz~2.462GHz 802.11b/g/n(1x1) 11b: DBPSK, DQPSK, CCK, DSSS 11g: BPSK, QPSK, 16QAM, OFDM Supported rates communication interface PCB layer structure PCB size Antenna 11n: MCS0~MSC7 OFDM 11b: 1, 2, 5.5 11Mbps 11g: 6,9,12,18,24,36,48,54Mbps 11n: MCS0~7, up to 150Mbps UART 2 Layer 18mm(L)x13mm(W)x1.0mm(H) PCB internal antennas Working temperature Storage temperature Hardware version number
-20~+85
-40~+125 RTK_UART_V1.0 2 Structure specification 2.1 Module structure size The size of the module as shown above, length 18mm, width 13mm, thickness 1.0mm (error +/- 0.1mm) 2.2 Hardware interface definition PIN Signal Name Description 1 2 3 4 VCC(V) RXD(R) TXD(T) VSS(GND) Supply Input Pin UART receive data UART transmit data Ground 3 Wireless Specification 3.1 802.11b mode Item Standard Mode Channel Data Rate Content IEEE802.11b DSSS/CCK CH1-CH11 1,2,5.5,11Mbps DC Characteristics DC Current(Average)@3.3V input Min. Typ. Max. Unit Remark 1) TX only @17dBm 2) TX throughput mode 3) RX throughput mode TX Characteristics 2. Power Level(Calibrated) 17dBm Target 3.Spectrum Mask @target Power Fc +/-11MHz to +/-22MHz Fc> +/- 22MHz 4.Frequency Error RX Characteristics 5.Minmum Input Level Sensitivity 1) 1Mbps(FER8%) 2) 2Mbps(FER8%) 3) 5.5Mbps(FER8%) 4) 11Mbps(FER8%) 6. Maximum Input Level(FER<=8%) 3.2 802.11g mode
-
-
-
Min. 15
-
-
-25 Min.
-20
-
-
-
Typ. 17
-
-
0 Typ.
-82
-10 280 120 100 Max. 19
-30
-50 25 Max.
-80
-80
-79
-76
-
Item Standard Mode Channel Data Rate Content IEEE802.11g OFDM CH1-CH11 6,9,12,18,24,36,48,54Mbps DC Characteristics Min. Typ. DC Current(Average)@3.3V input 1) TX only @16dBm 2) TX throughput mode 3) RX throughput mode TX Characteristics 2. Power Level(Calibrated) 1) 17dBm Target @6Mbps 2) 14dBm Target @54Mbps 3.Spectrum Mask @target Power at fc +/-11MHz to +/-20MHz at fc +/- 20MHz at fc> +/-30MHz 4.Constellation power 1)6Mbps 2)9Mbps Error(EVM)@target
-
-
-
-
-
-
Min. Typ. 15 12
-
-
17 14
-
-
Max. 280 120 100 Max. 19 16
-20
-28
-40
-5
-8 mA mA Unit dBm dBr dBr ppm Unit dBm dBm dBm dBm dBm Unit mA mA mA Unit dBm dBm dBr dBr dBr dB dB Remark 3)12Mbps 4)18Mbps 5)24Mbps 6)36Mbps 7)48Mbps 8)54Mbps 5. Frequency Error RX Characteristics 6. Minimum Input Level Sensitivity 1) 6Mbps(PER10%) 2) 9Mbps(PER10%) 3) 12Mbps(PER10%) 4) 18Mbps(PER10%) 5) 24Mbps(PER10%
6) 36Mbps(PER10%) 7) 48Mbps(PER10%) 8) 54Mbps(PER10%) 7. Maximum Input Level (PER<=10%) 3.3 802.11n HT20mode
-20 Min.
-20
-28 0 Typ.
-71
-10
-10
-13
-16
-19
-22
-25 20 Max.
-82
-81
-79
-77
-74
-70
-66
-65
-
dB dB dB dB dB dB Ppm Unit dBm dBm dBm dBm dBm dBm dBm dBm dBm Item Standard Mode Channel Data Rate(MCS Index) Content IEEE802.11n HT20 @2.4Ghz OFDM CH1-CH11 MCS0/1/2/3/4/5/6/7 DC Characteristics DC Current(Average)@5V input 1) TX only @17dBm Target(each port),
(continue Tx MIMO MCS7) 2) TX throughput mode 3) RX throughput mode Min. Typ.
-
-
-
TX Characteristics Min. Typ. 2. Power Level 1)17dBm Target@MCS0 2)13dBm Target@MCS7 3.Spectrum Mask @target Power at fc +/-11MHz at fc +/- 20MHz at fc> +/-30MHz 4.Constellation Error(EVM)@target power 1)MCS0 15 11
-
-
17 13
-
-
Max. 280 120 100 Max. 19 15
-20
-28
-45
-5 Unit mA mA mA Unit dBm dBm dBr dBr dBr dB Remark 2)MCS1 3)MCS2 4)MCS3 5)MCS4 6) MCS5 7) MCS6 8) MCS7 5. Frequency Error RX Characteristics 6. Minimum Input Level Sensitivity 1) MCS0(PER10%) 2) MCS1(PER10%) 3) MCS2(PER10%) 4) MCS3(PER10%) 5) MCS4(PER10%
6) MCS5Mbps(PER10%) 7) MCS6Mbps(PER10%) 8) MCS7Mbps(PER10%) 7. Maximum Input Level (PER<=10%) 3.4 802.11n HT40mode Item Standard Mode Channel Data Rate(MCS Index) DC Characteristics DC Current(Average)@5V input 1) TX only @16dBm Target 2) TX throughput mode 3) RX throughput mode
-20 Min.
-20
-30 0 Typ.
-70
-10
-10
-13
-16
-19
-22
-25
-27 20 Max.
-82
-79
-77
-74
-70
-66
-65
-64
-
dB dB dB dB dB dB dB Ppm Unit dBm dBm dBm dBm dBm dBm dBm dBm dBm Content IEEE802.11n HT40 @2.4Ghz OFDM CH3-CH9 MCS0/1/2/3/4/5/6/7/8/9/10/11/12/13/14/15 Min. Typ. Max. Unit Remark
-
-
-
TX Characteristics Min. Typ. 2. Power Level 1)14dBm Target 2)12dBm Target 3.Spectrum Mask @target Power at fc +/-21MHz at fc+/- 40MHz at fc> +/-60MHz 4.Constellation Error(EVM)@target power 1)MCS0 14 10
-
-
16 12
-
-
240 120 100 Max. 18 14
-20
-28
-45
-5 mA mA mA Unit dBm dBm dBr dBr dBr dB 2)MCS1 3)MCS2 4)MCS3 5)MCS4 6) MCS5 7) MCS6 8) MCS7 5. Frequency Error RX Characteristics
-20 Min.
-30 0 Typ.
-10
-13
-16
-19
-22
-25
-27 20 Max. dB dB dB dB dB dB dB Ppm Unit
-20
-66
-10
-79
-76
-74
-71
-67
-63
-62
-61
-
dBm dBm dBm dBm dBm dBm dBm dBm dBm 6. Minimum Input Level Sensitivity 1) MCS0(PER10%) 2) MCS1(PER10%) 3) MCS2(PER10%) 4) MCS3(PER10%) 5) MCS4(PER10%
6) MCS5Mbps(PER10%) 7) MCS6Mbps(PER10%) 8) MCS7Mbps(PER10%) 7. Maximum Input Level (PER<=10%) Federal Communication Commission Interference Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the partyresponsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any otherantenna or transmitter. Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for anuncontrolled environment. This equipment should be installed and operated withminimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antennaand users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for anyadditional compliance requirements required with this module installed IMPORTANT NOTE:In the event that these conditions can not be met (for examplecertain laptop configurations or co-location with another transmitter), then the FCCauthorization is no longer considered valid and the FCC ID can not be used on thefinal product. In these circumstances, the end product(including the transmitter) and obtaining a separate FCCauthorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may beinstalled such that 20 cm may be maintained between the antenna and users. Thefinal endproduct must be labeled in a visible area with the following: Contains FCCID: 2AIRV0002. The grantee's FCC ID can be used only when all FCCcompliance requirements aremet. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end userregarding how to install or remove this RF module in the users manual of the endproduct which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. integrator will be reevaluating responsible the OEM for