FCC ID: 2ABZJ-100-00113 A6

A6 Optional: SFP+ fiber (non-copper) module and preferred optical cabling Optional: 19mm (3/4) flexible conduit/

hose tubing and hose-clamps for additional cable protection UNLOCK REQUIRED This device requires unlocking prior to use. For all unlocking instructions and options prior to onsite installation, please visit:

mimosa.co/start 1. Mounting Tightly attach the supplied sliding & pivot brackets to mounting pole in desired up or downtilt orientation. 20 10 5 0 15 3. Dedicated 48VDC Power Thread an 18 AWG 2-pin cable through one the supplied IP67 gland/cap. Strip the wire jackets approximately 6-7mm, and attach to the supplied power connector terminals (+/- indicated in diagram). Tighten the terminal screws. Note: reverse polarization will not dam-

age the device, however proper +/- wir-

ing is required to apply power. Insert and snap the power plug and cable into the PWR port. Attach and tighten gland, attach the rubber insert to the cable, pushing it into the gland, then tighten the cap. 5 & 6 GHz Fixed Wireless WiFi 6E PTMP Access Point 15 10 5 0 20 For instructions, videos and help visit:

Para obtener videos y ayuda, visite:

Pour obtenir des vidos et de laide, visitez:

support.mimosa.co Para obtener instrucciones, videos y ayuda, visite:

Pour obtenir des instructions, des vidos et de laide, visitez:

setup.mimosa.co 2. Grounding Attach 10 AWG ground wire with pre-termi-

nated ring terminal to the grounding screw. Additional Required & Optional Items 10 AWG (5.26 mm2) ground cable with pre-terminated ring terminal Small flat head type screwdriver (for direct 48VDC power terminal) 15, 13 and 10 mm socket or adjustable wrench for mounting assembly Power Option A: 18 AWG 2-pin wire for direct power wiring 48VDC input Power Option B: Shielded CAT6/6A &

compatible PoE injector (refer to A6 datasheet specifications) 10 AWG PWR ETH 1 c a b 18 AWG d e f PWR ETH 1 4. Gigabit Ethernet or PoE Insert a shielded CAT6/6A Ethernet cable through the IP67 gland/cap. Connect the cable to ETH port. Attach and tighten gland, attach the rubber insert to the cable, pushing it into the gland, then tighten the cap. PoE powering is optional and can be used as primary or as redundant/backup power to the 48VDC. Ethernet connection is NOT required if SFP+ optical fiber is being used. PWR ETH 1 2 CAT 6/6E a b c d 6. Optional SFP+ Optical Fiber Two SFP+ ports are provided to accom-

modate standard SFP+ 10 Gbps optical modules, and bult-in switching between the ports for interconnectivity to other devices. Visit support for additional SFP+ module and configuration information. 7. Seal All Unused Ports For any unused ports, tightly screw in the supplied port sealing caps to maintain envi-

ronmental integrity of the system. 8. Unlock and Configure Visit start.mimosa.co to unlock the device. Warnings, Warranty, Compliance

& Regulatory Statements Mimosa by Airspan (Mimosa) products are provided by Airspan Networks Inc. (Airspan). Export Control These commodities, technology, or software were exported from the United States in accordance with the Export Administration Regulations. Diversion contrary to U.S. law is prohibited. 5. Optional Flexible Conduit The provided IP67 gland caps are designed to accommodate optional 19mm (3/4) outdoor hose conduit/tubing, and hose-type clamps to secure the tubing. Both can be procured at most hardware stores. Important Safety and Handling Information Failure to follow any of the safety instructions in this guide, instructions on any Airspan provided packaging, and heed WARNINGS (indicated by ), could result in fire, electric shock, other injury or death, and incur damage to this product or other property and void the products Limited Warranty. There are no End User serviceable parts inside the equipment. Read all operating and safety instructions contained herein and accom-

panying the product as provided by Airspan:

ETH 1 2 Hose Clamp Hose Tubing 3/4 (19 mm) Electrical Safety Information Do not operate this product in any location that can be sub-

merged by water. Do not install or maintain this product during the presence of an electrical storm to avoid risk of electric shock from lightning. Fail-

ure to ground the device according to the included instructions using shielded CAT6/6A Ethernet cabling could lead to serious injury or death. Installation of the product must comply with local and national electrical codes. Power specifications for connected devices are indicated on the devices own label or documentation. Connecting to any power source that does not meet the voltage, frequency and current requirements listed may damage the power supply or product, and pose a fire hazard. Mandatory Grounding Instructions IMPORTANT: Failure to properly ground the device using the following instructions will violate the limited warranty conditions in this document. Required Step 1- Direct Grounding on the Device:

A minimum grounding wire of 10 AWG (5.26 mm2) with a secured grounding terminal, and shorter in length than 1 meter is required. It is NOT supplied with the product. on the 1. Ensure that NO power is being supplied to the product. 2. Locate the Ground point screw next to the Ground icon device 3. Remove the provided Ground Screw 4. Thread the ground wire terminal and ground wire meeting the above specifications over the screw removed in the previous step. 5. Replace and tighten the screw with the threaded ground terminal and cable at the product Ground point. 6. Secure the other end of the grounding cable to the properly grounded structure (pole, tower, mast, etc.) meeting local and national electrical regulations and codes. End User Product Warranty The product is warranted against defects in material, and workmanship for a period of twenty four (24) months from the date of first unlock of the product. Please go to www.mimosa.co/warranty to determine whether your product is in warranty. The sole responsibility of Airspan under this warranty shall be limited to the repair or replacement of in-warranty defective product, at Airspans sole option. Out of warranty products shipped to Airspan will not be returned. This warranty does not cover costs associated with the removal and/or reinstallation of the product for repair nor for any parts that are readily replaced in normal use. Airspan or its designated partner will repair or replace product found to be defective during the defined warranty period. The End User is responsible for delivering defective product in accordance with the Return Material Authorization (RMA) processes published at www.mimosa.co/legal/RMA Limitation of Warranty The product warranty is invalidated if the RMA product is altered or otherwise tampered with in a manner that modifies the product from its original shipping configuration and/or form factor, and could violate the End Users authority to operate the equipment, unless said activity was performed by or with the written authorization of an Airspan representative. Modifications include:

(a) External surfaces that have been painted, labeled, or otherwise modified from the original shipping condition.

(b) Modifications of the product with third party hardware, firmware, and/or software.

(c) Any product subjected to abnormal physical or electric stress, including, but not limited to, lightning strikes, negligence, accident, or misuse.

(d) Any product damaged due to incorrect installation, including, but not limited to, improper product mounting, cabling meeting minimum requirements in this manual, cabling defects or connection to power.

(e) Failure induced by connected third party products. Installing the product outdoors without the use of minimum CAT6/6A shielded Ethernet cable, improper grounding, or failure to ground the product as instructed in this guide will void the End User Product warranty. Disclaimer EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, AIRSPAN AND ITS SUBSIDIARIES, LICENSORS AND AFFILIATES (

COLLECTIVELY, AIRSPAN), AND ANY THIRD PARTY DATA, SERVICE, SOFTWARE AND HARDWARE PROVIDERS MAKE NO OTHER REPRE-

SENTATION OR WARRANTY OF ANY KIND AND HEREBY DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, STATUTORY OR OTHER-

WISE, INCLUDING, BUT NOT LIMITED TO, ANY REPRESENTATIONS OR WARRANTIES OF DESIGN, MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY, QUIET ENJOY-

MENT, FITNESS FOR A PARTICULAR PURPOSE, NON-INFRINGEMENT AND ANY WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR TRADE PRACTICE IN CONNECTION WITH SUCH PROD-

UCTS AND SERVICES. YOU ACKNOWLEDGE THAT NEITHER AIRSPAN NOR ITS THIRD PARTY PROVIDERS CONTROL YOUR EQUIPMENT OR THE TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING THE INTERNET, AND THAT THE PRODUCTS AND SERVICES PROVIDED BY AIRSPAN MAY BE SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS FACILITIES. AIRSPAN AND ANY THIRD PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTER-

RUPTIONS, DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY OF THE FOREGOING. IN ADDITION, AIRSPAN MAKES NO WARRANTY OR UNDERTAK-

ING, AND MAKES NO REPRESENTATION OF ANY KIND THAT THE LICENSED PRODUCTS WILL MEET YOUR REQUIREMENTS, ACHIEVE ANY INTENDED RESULTS, BE COMPATIBLE OR WORK WITH ANY OTHER APPLICATIONS, SYSTEMS OR SERVICES, OPERATE WITHOUT INTERRUPTION, MEET ANY PERFORMANCE OR RELIABILITY STAN-

DARDS, BE ERROR FREE OR THAT ANY ERRORS OR DEFECTS CAN OR WILL BE CORRECTED, OR THAT THE LICENSED PRODUCTS ARE NOT VULNERABLE TO FRAUD OR UNAUTHORIZED USE. Limitation of Liability EXCEPT TO THE EXTENT PROHIBITED BY THE LAWS IN YOUR JURISDICTION, IN NO EVENT WILL AIRSPAN OR ITS SUPPLIERS OR LICENSORS BE LIABLE FOR SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES (INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), NOR FOR DAMAGES BASED ON UNAUTHO-

RIZED USE OR ACCESS, ARISING OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL AIRSPAN, ITS SUPPLIERS OR ITS LI-

CENSORS DIRECT LIABILITY EXCEED THE VALUE OF THE LICENSED PRODUCTS GIVING RISE TO SUCH LIABILITY. THESE LIMITATIONS SHALL APPLY NOTHWITHSTANDING ANY FAILURE OF ESSENTIAL PURPOSE OF ANY LIMITED REMEDY. IN NO EVENT SHALL AIRSPAN BE RESPONSIBLE FOR DAMAGES OR CLAIMS OF ANY NATURE OR DESCRIPTION RELATING TO NETWORK PERFORMANCE, INCLUDING COVERAGE, YOUR SELECTION OF AIRSPAN PRODUCTS FOR YOUR PARTICULAR APPLICATION AND/OR FAILURE OF AIRSPAN PROD-

UCTS TO MEET GOVERNMENT OR REGULATORY REQUIREMENTS. Some legal jurisdictions do not allow exclusions of implied warranties or conditions, or for the exclusion or limitation of liability for incidental or consequential damages, so the above exclusion may not apply to you. You may have other rights specific to your legal jurisdiction. EXCEPT TO THE EXTENT ALLOWED BY THE LAW OF YOUR JURISDICTION, THESE WARRANTY TERMS DO NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, ANY MANDATORY STATUTORY RIGHTS APPLICABLE TO YOU IN THE LICENSE OF ANY EMBEDDED SOFTWARE. The United Nations Convention on Contracts for the Inter-

national Sale of Goods shall not apply to any transactions regarding the sale of the Products. FCC This device complies with part 15 of the FCC Rules. Operation is sub-

ject to the following two conditions:

suivantes:

(1) Cet appareil ne peut pas provoquer dinterfrences et (2) Cet ap-

pareil doit accepter toute interfrence, y compris les interfrences qui peuvent causer un mauvais fonctionnement du dispositif.

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Australia & New Zealand NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio commu-

nications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. The radiated output power of this device is below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact during the normal operation is minimized. In order to avoid the possibility of exceeding the FCC radio frequency exposure limit, human proximity to the anten-

na should be more than 3m. When mounting the radio antenna, in accordance with the Part 15 UNII-

1 band requirements, the antenna must not exceed 125 mW (21 dBm) e.i.r.p. at any elevation angle above 30 degrees as measured from the horizon). Important: Changes or modifications to this product not authorized by Mimosa Networks, Inc. could void the electromagneticcompatibility

(EMC) and wireless compliance and negate your authority to-

operate the product. The information in this guide may change without notice. The manufacturer assumes no responsibility for any errors that may appear in this guide. Industry Canada This Class A digital apparatus complies with Canadian CAN ICES-3(A). Cet appareil numrique de la classe A est conforme la norme NMB-

3(A) Canada. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Pour rduire le risque dinterfrence aux autres utilisateurs, le type dantenne et son gain doivent tre choisies de faon que la puissance isotrope rayonne quivalente (PIRE) ne dpasse pas ce qui est nces-

saire pour une communication russie. This device complies with Industry Canada licence-exempt RSS stan-

dard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme la norme RSS Industrie Canada exempts de licence norme(s). Son fonctionnement est soumis aux deux conditions European Compliance Statement CE Marking on this product represents that this product com-

plies with all requirements that are applicable to it. Europe EU Declaration of Conformity This device can be used in the European Community. A copy of the EU Decla-

ration of Conformity is available at: www.mimosa.co/compliance.

(Bulgarian) - Airspan Networks Inc. , Airspan Networks Inc. 2014/53/EU. esky (Czech) - Spolenost Airspan Networks Inc. tmto prohlauje, e tento Airspan Networks Inc. zazen je ve shod se zkladnmi poadavky a dalmi pslunmi ustanovenmi smrnice 2014/53/EU. Dansk (Danish) - Undertegnede Airspan Networks Inc. erklrer herved, at flgende udstyr Airspan Networks Inc. enhed overholder de vsentlige krav og vrige relevante krav i direktiv 2014/53/EU. Deutsch (German) - Hiermit erklrt Airspan Networks Inc., dass sich das Airspan Networks Inc. Gert in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschlgigen Bestimmungen der Richtlinie 2014/53/EU befinden. Eesti (Estonian) - Kesolevaga kinnitab Airspan Networks Inc., et see Airspan Networks Inc. seade vastab direktiivi 2014/53/EU phinuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele stetele. English - Hereby, Airspan Networks Inc. declares that this Airspan Networks Inc. device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Espaol (Spanish) - Por medio de la presente Airspan Networks Inc. declara que este Airspan Networks Inc. dispositivo cumple con los requisitos esen-

ciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 2014/53/EU.

(Greek) - M , Airspan Networks Inc. Airspan Networks Inc. 2014/53/EU. Franais (French) - Par la prsente Airspan Networks Inc. dclare que ce Airspan Networks Inc. appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 2014/53/EU. Islenska (Icelandic) - Airspan Networks Inc. lsir v hr me yfir a etta Airspan Networks Inc. tki fullngir lgmarkskrfum og rum vieigandi kvum Evrputilskipunar 2014/53/EU. Italiano (Italian) - Con la presente Airspan Networks Inc. dichiara che questo Airspan Networks Inc. dispositivo conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 2014/53/EU. Latviski (Latvian) - Ar o Airspan Networks Inc. deklar, ka Airspan Networks Inc. ierce atbilst Direktvas 2014/53/EU btiskajm prasbm un citiem ar to saisttajiem noteikumiem. Lietuvi (Lithuanian) - iuo Airspan Networks Inc. deklaruoja, kad is Airspan Networks Inc. atitinka esminius reikalavimus ir kitas 2014/53/EUB Direktyvos nuostatas. Magyar (Hungarian) - Alulrott, Airspan Networks Inc. nyilatkozom, hogy a Air-

span Networks Inc. eszkz megfelel a vonatkoz alapvet kvetelmnyeknek s az 2014/53/EU irnyelv egyb elrsainak. Malti (Maltese) - Hawnhekk, Airspan Networks Inc., jiddikjara li dan Airspan Networks Inc. tagmir jikkonforma mal-tiijiet essenzjali u ma provvedimenti orajn relevanti li hemm fid-Dirrettiva 2014/53/EU. Nederlands (Dutch) - Hierbij verklaart Airspan Networks Inc. dat dit Airspan Networks Inc. toestel in overeenstemming is met de essentile eisen en de andere bepalingen van richtlijn 2014/53/EU. Norsk (Norwegian) - Airspan Networks Inc. erklrer herved at dette Airspan Networks Inc. apparatet er i samsvar med de grunnleggende kravene og vrige relevante krav i EU-direktivet 2014/53/EU. Polski (Polish)- Niniejszym Airspan Networks Inc. owiadcza, e ten Airspan Networks Inc. urzdzenie s zgodne z zasadniczymi wymogami oraz pozos-

taymi stosownymi postanowieniami Dyrektywy 2014/53/EU. Portugus (Portugese) - Airspan Networks Inc. declara que este Airspan Networks Inc. dispositivo est em conformidade com os requisitos essenciais e outras disposies da Directiva 2014/53/EU. Romn (Romanian) - Prin prezenta, Airspan Networks Inc. declar c acest Airspan Networks Inc. aparat este n conformitate cu cerinele eseniale i cu celelalte prevederi relevante ale Directivei 2014/53/EU. Slovensky (Slovak) - Airspan Networks Inc. tmto vyhlasuje, e toto Airspan Networks Inc. zariadenie spa zkladn poiadavky a vetky prslun ustano-

venia Smernice 2014/53/EU. Slovensko (Slovene) - Airspan Networks Inc. izjavlja, da je ta Airspan Networks Inc. naprava skladne z bistvenimi zahtevami in ostalimi ustreznimi doloili direktive 2014/53/EU. Suomi (Finnish) - Airspan Networks Inc. vakuuttaa tten, ett tm Airspan Networks Inc. tyyppinen laite on direktiivin 2014/53/EU oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. Svenska (Swedish) - Hrmed intygar Airspan Networks Inc. att denna Airspan Networks Inc. apparat str i verensstmmelse med de vsentliga egenskapsk-

rav och vriga relevanta bestmmelser som framgr av direktiv 2014/53/EU. RoHS & WEEE Compliance User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE). This document contains important information for users with re-

gards to the proper disposal and recycling of Airspan Networks Inc. products. Consumers are required to comply with this notice for all electronic products bearing this symbol. English - Environmental Information for Customers in the European Union European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.

(Bulgarian) -

2002/96/EC , /

. etina (Czech) - Informace o ochran ivotnhoprosted pro zkaznky v zemch Evropsk unie - Evropsk smrnice 2002/96/ES zakazuje, aby zazen oznaen tmto symbolem na produktu anebo na obalu bylo likvidovno s netdnm komunlnm odpadem. Tento symbol udv, e dan produkt mus bt likvidovn oddlen od bnho komunlnho odpadu. Odpovdte za likvidaci tohoto produktu a dalch elektrickch a elektronickch zazen pros-

tednictvm urench sbrnch mst stanovench vldou nebo mstnmi ady. Sprvn likvidace a recyklace pomh pedchzet potencilnm negativnm dopadm na ivotn prosted a lidsk zdrav. Podrobnj informace o likvidaci starho vybaven si laskav vydejte od mstnch ad, podniku zabvajcho se likvidac komunlnch odpad nebo obchodu, kde jste produkt zakoupili. Dansk (Danish) - Miljinformation for kunder i EU - EU-direktiv 2002/96/EF krver, at udstyr der brer dette symbol p produktet og/eller emballagen ikke m bortskaffes som usorteret kommunalt affald. Symbolet betyder, at dette produkt skal bortskaffes adskilt fra det almindelige husholdningsaffald. Det er dit ansvar at bortskaffe dette og andet elektrisk og elektronisk udstyr via bestemte indsamlingssteder udpeget af staten eller de lokale myndighed-

er. Korrekt bortskaffelse og genvinding vil hjlpe med til at undg mulige skader for miljet og menneskers sundhed. Kontakt venligst de lokale myn-

digheder, renovationstjenesten eller den butik, hvor du har kbt produktet, angende mere detaljeret information om bortskaffelse af dit gamle udstyr. Deutsch (German) - Umweltinformation fr Kunden innerhalb der Eu-

ropischen Union - Die Europische Richtlinie 2002/96/EC verlangt, dass technische Ausrstung, die direkt am Gert und/oder an der Verpackung mit diesem Symbol versehen ist, nicht zusammen mit unsortiertem Gemeinde-

abfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulrem Haushaltmll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gert und andere elektrische und elektronische Gerte ber die dafr zustndigen und von der Regierung oder rtlichen Behrden dazu bestimmten Sammelstellen zu entsorgen. Ordnungsgemes Entsorgen und Recyceln trgt dazu bei, potentielle negative Folgen fr Umwelt und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer Altgerte bentigen, wenden Sie sich bitte an die rtlichen Behrden oder stdtischen Entsorgungsdienste oder an den Hndler, bei dem Sie das Produkt erworben haben. Eesti (Estonian) - Keskkonnaalane informatsioon Euroopa Liidus asuvatele kli-

entidele - Euroopa Liidu direktiivi 2002/96/E nuete kohaselt on seadmeid, millel on tootel vi pakendil kesolev smbol keelatud krvaldada koos sort-

eerimata olmejtmetega. See smbol nitab, et toode tuleks krvaldada eral-

di tavalistest olmejtmevoogudest. Olete kohustatud krvaldama kesoleva ja ka muud elektri- ja elektroonikaseadmed riigi vi kohalike ametiasutuste poolt ette nhtud kogumispunktide kaudu. Seadmete korrektne krvaldamine ja ringlussevtt aitab vltida vimalikke negatiivseid tagajrgi keskkonnale ning inimeste tervisele. Vanade seadmete krvaldamise kohta tpsema informatsiooni saamiseks vtke palun hendust kohalike ametiasutustega, jtmekitlusfirmaga vi kauplusega, kust te toote ostsite. Espaol (Spanish) - Informacin medioambiental paraclientes de la Unin Europea - La Directiva 2002/96/CE de la UE exige que los equipos quel leven este smbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El smbolo indica que el producto en cuestin debe separarse de los residuos domsticos conven-

cionales con vistas a su eliminacin. Es responsabilidad suya desechar este y cualesquiera otros aparatos elctricos y electrnicos a travs de los puntos de recogida que ponen a su disposicin el gobierno y las autoridades locales. Al desechar y reciclar correctamente estos aparatos estar contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y la salud de las personas. Si desea obtener informacin ms detallada sobre la eliminacin segura de su aparato usado, consulte a las autoridades locales, al servicio de recogida y eliminacin de residuos de su zona o pregunte en la tienda donde adquiri el producto.

(Greek) -

- 2002/96/

EC, /

. Franais (French) - Informations environnementales pour les clients de lUnion europenne - La directive europenne 2002/96/CE exige que lquipement

, sur lequel est appos ce symbole sur le produit et/ou son emballage ne soit pas jet avec les autres ordures mnagres. Ce symbole indique que le produit doit tre limin dans un circuit distinct de celui pour les dchets des mnages. Il est de votre responsabilit de jeter ce matriel ainsi que tout autre matriel lectrique ou lectronique par les moyens de collecte indiqus par le gouvernement et les pouvoirs publics des collectivits territoriales. Llimination et le recyclage en bonne et due forme ont pour but de lutter contre limpact nfaste potentiel de ce type de produits sur lenvironnement et la sant publique. Pour plus dinformations sur le mode dlimination de votre ancien quipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des dchets, ou lendroit o vous avez achet le produit. Italiano (Italian) - Informazioni relative allambiente per i clienti residenti nellUnione Europea - La direttiva europea 2002/96/EC richiede che le appare-

cchiature contrassegnate con questo simbolo sul prodotto e/o sullimballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti do-

mestici. responsabilit del proprietario smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il corretto smaltimen-

to ed il riciclaggio aiuteranno a prevenire conseguenze potenzialmente nega-

tive per lambiente e per la salute dellessere umano. Per ricevere informazioni pi dettagliate circa lo smaltimento delle vecchie apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto. Latvieu valoda (Latvian) - Ekoloiska informcija klientiem Eiropas Savienbas jurisdikcij - Direktv 2002/96/EK ir prasba, ka aprkojumu, kam pievienota zme uz paa izstrdjuma vai uz t iesaiojuma, nedrkst izmest neirot veid kop ar komunlajiem atkritumiem (tiem, ko rada vietji iedzvotji un uzmumi). zme nozm to, ka ierce ir jizmet atkritumos t, lai t neno-

nktu kop ar parastiem mjsaimniecbas atkritumiem. Jsu pienkums ir o un citas elektriskas un elektroniskas ierces izmest atkritumos, izmantojot paus atkritumu savkanas veidus un ldzekus, ko nodroina valsts un pavaldbu iestdes. Ja izmeana atkritumos un prstrde tiek veikta pareizi, tad mazins iespjamais kaitjums dabai un cilvku veselbai. Skkas zias par novecojua aprkojuma izmeanu atkritumos js varat saemt vietj pavaldb, atkritumu savkanas dienest, k ar veikal, kur iegdjties o izstrdjumu. Lietuvkai (Lithuanian) - Aplinkosaugos informacija,skirta Europos Sjungos vartotojams - Europos direktyva 2002/96/EC numato, kad rangos, kuri ir kurios pakuot yra paymta iuo simboliu, negalima alinti kartu su neriuotomis komunalinmis atliekomis. is simbolis rodo, kad gamin reikia alinti atskirai nuo bendro buitini atliek srauto. Js privalote utikrinti, kad i ir kita elektros ar elektronin ranga bt alinama per tam tikras nacionalins ar vietins valdios nustatytas atliek rinkimo sistemas. Tinkamai alinant ir perdirbant atliekas, bus ivengta galimos alos aplinkai ir moni sveikatai. Daugiau infor-

macijos apie js senos rangos alinim gali pateikti vietins valdios instituci-

jos, atliek alinimo tarnybos arba parduotuvs, kuriose sigijote t gamin. Malti (Maltese) - Informazzjoni Ambjentali gal Klijentifl-Unjoni Ewropea Id-Direttiva Ewropea 2002/96/KE titlob li t-tagmir li jkun fih is-simbolu fuq il-prodott u/jew fuq l-ippakkjar ma jistax jintrema ma skart muniipali li ma iex isseparat. Is-simbolu jindika li dan il-prodott gandu jintrema separat-

ament minn ma l-iskart domestiku regolari. Hija responsabbilt tiegek li tarmi dan it-tagmir u kull tagmir ieor ta l-elettriku u elettroniku permezz ta failitajiet ta bir appuntati apposta mill-gvern jew mill-awtoritajiet lokali. Ir-rimi bmod korrett u r-riikla jgin jipprevjeni konsegwenzi negattivi potenzjali gall-ambjent u gas-saa tal-bniedem. Gal aktar informazzjoni dettaljata dwar ir-rimi tat-tagmir antik tiegek, jekk jogbok ikkuntattja lill-awtoritajiet lokali tiegek, is-servizzi gar-rimi ta l-iskart, jew il-anut minn fejn xtrajt il-prodott. Magyar (Hungarian) - Krnyezetvdelmi informci azeurpai unis vsrlk szmra - A 2002/96/EC szm eurpai unis irnyelv megkvnja, hogy azokat a termkeket, amelyeken, s/vagy amelyek csomagolsn az albbi cmke megjelenik, tilos a tbbi szelektlatlan lakossgi hulladkkal egytt kidobni. A cmke azt jelli, hogy az adott termk kidobsakor a szokvnyos hztartsi hulladkelszlltsi rendszerektl elklntett eljrst kell alkalmazni. Az n felelssge, hogy ezt, s ms elektromos s elektronikus berendezseit a kormnyzati vagy a helyi hatsgok ltal kijellt gyjtredszereken keresztl szmolja fel. A megfelel hulladkfeldolgozs segt a krnyezetre s az emberi egszsgre potencilisan rtalmas negatv hatsok megelzsben. Ha elavult berendezseinek felszmolshoz tovbbi rszletes informcira van szksge, krjk, lpjen kapcsolatba a helyi hatsgokkal, a hulladkfeldolgo-

zsi szolglattal, vagy azzal zlettel, ahol a termket vsrolta. Nederlands (Dutch) - Milieu-informatie voor klantenin de Europese Unie - De Europese Richtlijn 2002/96/EC schrijft voor dat apparatuur die is voorzien van dit symbool op het product of de verpakking, niet mag worden ingezameld met niet-gescheiden huishoudelijk afval. Dit symbool geeft aan dat het product apart moet worden ingezameld. U bent zelf verantwoordelijk voor de vernietiging van deze en andere elektrische en elektronische apparatuur via de daarvoor door de landelijke of plaatselijke overheid aangewezen inzamel-

ingskanalen. De juiste vernietiging en recycling van deze apparatuur voorkomt mogelijke negatieve gevolgen voor het milieu en de gezondheid. Voor meer informatie over het vernietigen van uw oude apparatuur neemt u contact op met de plaatselijke autoriteiten of afvalverwerkingsdienst, of met de winkel waar u het product hebt aangeschaft. Norsk (Norwegian) - Miljinformasjon for kunder i EU - EU-direktiv 2002/96/EF krever at utstyr med flgende symbol avbildet p produktet og/eller paknin-

gen, ikke m kastes sammen med usortert avfall. Symbolet indikerer at dette produktet skal hndteres atskilt fra ordinr avfallsinnsamling for husholdning-

savfall. Det er ditt ansvar kvitte deg med dette produktet og annet elektrisk og elektronisk avfall via egne innsamlingsordninger slik myndighetene eller kommunene bestemmer. Korrekt avfallshndtering og gjenvinning vil vre med p forhindre mulige negative konsekvenser for milj og helse. For nrmere informasjon om hndtering av det kasserte utstyret ditt, kan du ta kontakt med kommunen, en innsamlingsstasjon for avfall eller butikken der du kjpte produktet. Polski (Polish) - Informacja dla klientw w Unii Europejskiej o przepisach dotyczcych ochrony rodowiska - Dyrektywa Europejska 2002/96/EC wymaga, aby sprzt oznaczony symbolem znajdujcym si na produkcie i/

lub jego opakowaniu nie by wyrzucany razem z innymi niesortowanymi odpadami komunalnymi. Symbol ten wskazuje, e produkt nie powinien by usuwany razem ze zwykymi odpadami z gospodarstw domowych. Na Pastwu spoczywa obowizek wyrzucania tego i innych urzdze elektrycznych oraz elektronicznych w punktach odbioru wyznaczonych przez wadze krajowe lub lokalne. Pozbywanie si sprztu we waciwy sposb i jego recykling pomog zapobiec potencjalnie negatywnym konsekwencjom dla rodowiska i zdrowia ludzkiego. W celu uzyskania szczegowych informacji o usuwaniu starego sprztu, prosimy zwrci si do lokalnych wadz, sub oczyszczania miasta lub sklepu, w ktrym produkt zosta nabyty. Portugus (Portuguese) - Informao ambiental paraclientes da Unio Euro-

peia - A Directiva Europeia 2002/96/CE exige que o equipamento que exibe este smbolo no produto e/ou na sua embalagem no seja eliminado junto com os resduos municipais vno separados. O smbolo indica que este pro-

duto deve ser eliminado separadamente dos resduos domsticos regulares. da sua responsabilidade eliminar este e qualquer outro equipamento elctrico e electrnico atravs das instalaes de recolha designadas pelas autoridades governamentais ou locais. A eliminao e reciclagem correctas ajudaro a prevenir as consequncias negativas para o ambiente e para a sade humana. Para obter informaes mais detalhadas sobre a forma de eliminar o seu equipamento antigo, contacte as autoridades locais, os servios de eliminao de resduos ou o estabelecimento comercial onde adquiriu o produto. Romn (Romanian) - Informaii de mediu pentruclienii din Uniunea Europe-

an - Directiva european 2002/96/CE impune ca echipamentele care prezint acest simbol pe produs i/sau pe ambalajul acestuia s nu fie casate mpreun cu gunoiul menajer municipal. Simbolul indic faptul c acest produs trebuie s fie casat separat de gunoiul menajer obinuit. Este responsabilitatea dvs. s casai acest produs i alte echipamente electrice i electronice prin intermediul unitilor de colectare special desemnate de guvern sau de autoritile locale. Casarea i reciclarea corecte vor ajuta la prevenirea potenialelor consecine negative asupra sntii mediului i a oamenilor. Pentru mai multe informaii detaliate cu privire la casarea acestui echipament vechi, contactai autoritile locale, serviciul de salubrizare sau magazinul de la care ai achiziionat produsul. Slovenina (Slovak) - Informcie o ochrane ivotnhoprostredia pre zkaznkov v Eurpskej nii - Poda eurpskej smernice 2002/96/ES zariadenie s tmto symbolomna produkte a/alebo jeho balen nesmie by likvidovan spolu s netriedenm komunlnym odpadom. Symbol znamen, e produkt by sa mal likvidova oddelene od benho odpadu z domcnost. Je vaou povinnosou likvidova toto i ostatn elektrick a elektronick zariadenia prostrednctvom pecializovanch zbernch zariaden urench vldou alebo miestnymi orgn-

mi. Sprvna likvidcia a recyklcia pome zabrni prpadnm negatvnym dopadom na ivotn prostredie a zdravie ud. Ak mte zujem o podrobnejie informcie o likvidcii starho zariadenia, obrte sa, prosm, na miestne orgny, organizcie zaoberajce sa likvidciou odpadov alebo obchod, v ktorom ste si produkt zakpili. Slovenina (Slovene) - Okoljske informacije za stranke v Evropski uniji - Ev-

ropska direktiva 2002/96/ES prepoveduje odlaganje opreme s tem simbolom na izdelku in/ali na embalai z nesortiranimi komunalnimi odpadki. Ta simbol opozarja, da je treba izdelek zavrei loeno od preostalih gospodinjskih odpadkov. Vaa odgovornost je, da to in preostalo elektrino in elektronsko opremo oddate na posebna zbiralia, ki jih doloijo dravne ustanove ali loka-

lne oblasti. S pravilnim odlaganjem in recikliranjem boste prepreili morebitne kodljive vplive na okolje in zdravje ljudi. e elite izvedeti ve o odlaganju stare opreme, se obrnite na lokalne oblasti, odlagalie odpadkov ali trgovino, kjer ste izdelek kupili. Suomi (Finnish) - Ymprist koskevia tietoja EU- alueen asiakkaille EU-direktiivi 2002/96/EY edellytt, ett jos laitteistossa on tm symboli itse tuotteessa ja/tai sen pakkauksessa, laitteistoa ei saa hvitt lajittelematto-

man yhdyskuntajtteen mukana. Symboli merkitsee sit, ett tm tuote on hvitettv erilln tavallisesta kotitalousjtteest. Sinun vastuullasi on hvitt tm elektroniikkatuote ja muut vastaavat elektroniikkatuotteet viemll tuote tai tuotteet viranomaisten mrmn keryspisteeseen. Laitteiston mahdolliset kielteiset vaikutukset ympristn ja ihmisten terveyteen. Listi-

etoja vanhan laitteiston oikeasta hvitystavasta saa paikallisilta viranomaisilta, jtteenhvityspalvelusta tai siit myymlst, josta ostit tuotteen Svenska (Swedish) - Miljinformation fr kunder i Europeiska unionen - Det europeiska direktivet 2002/96/EC krver att utrustning med denna symbol p produkten och/eller frpackningen inte fr kastas med osorterat kommunalt avfall. Symbolen visar att denna produkt br kastas efter att den avskiljts frn vanligt hushllsavfall. Det faller p ditt ansvar att kasta denna och annan elektrisk och elektronisk utrustning p faststllda insamlingsplatser utsedda av regeringen eller lokala myndigheter. Korrekt kassering och tervinning skyddar mot eventuella negativa konsekvenser fr miljn och personhlsa. Fr mer detaljerad information om kassering av din gamla utrustning kontaktar du dina lokala myndigheter, avfallshanteringen eller butiken dr du kpte produkten. 2022 Airspan Networks Inc. All rights reserved. 705-00034 REV A

Label Sample 4X R2.0 Code-128 barcode embedded with serial number:

XXYYYYYYYY Unique device S/N: XX-YYYY-YY and MAC:XX:XX:XX:XX:XX:XX text:

Avenir Black 7 pt All fonts and pring Process Black Model: A6 Assembled in Malaysia FCC ID: 2ABZJ-100-00113 IC: 11823A-10000113 Airspan Networks Inc. Boca Raton, FL USA This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 37.5 S/N: XX-YYYY-YYYY MAC: XX:XX:XX:XX:XX:XX 42.5 Uses Raw Label and material/adhesive specified in P/N 617-00011 PRINT ART in Process BLACK (ignore color defined in raw label) UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN MILLIMETERS SURFACE FINISH:

TOLERANCES:

LINEAR:

ANGULAR:

FINISH: Refer to 617-00011 ADHESIVE: Refer to 617-00011 MATERIAL: Refer to 617-00011) NAME SIGNATURE DATE TITLE:

DO NOT SCALE DRAWING DRAWN Jaime Fink CHK'D APPV'D MFG Q.A A6 Product & SN Label MATERIAL:

DWG NO. 615-00363 1 REVISION WEIGHT:

SCALE:1:1 SHEET 1 OF 1 D C B A 4 3 2 1 28X 22 6.0 KGF-CM STAR PATTERN Label Location 25 10X 19 6.0 KGF-CM D C B 24 ITEM NO. 18 19 20 21 22 23 24 25 PART NUMBER 010-00171 602-00141 611-00037 010-00170 602-00142 310-00085 602-00114 615-00363 4 DESCRIPTION ASM, ANTENNA, A6 SCR, FHCS, M3 X 0.5P X 6L, ZN-AS, NYLOK O-RING, CS 5.33, DASH NO. 387 ASM, RADOME, A6 SCR, FHCS, M3 X 0.5P X 8L, ZN-AS, NYLOK TERM BLOCK PLUG WITH LATCH 2POS STR 5.08MM SCREW, PAN HEAD, M4X10, SS, WITH EXTERNAL-TOOTH WASHER LABEL, PRODUCT AND S/N, A6 QTY 1 10 1 1 28 1 1 1 3 2 1 DESCRIPTION:

ASSEMBLY, A6 ACCESS POINT DWG. NO.:

010-00167 SIZE:

A B 2 REV:

DO NOT SCALE DRAWING SCALE:

SHEET:

1:4 6 OF 6 23 18 SEE SHEET 5 20 21 ENSURE O-RING AND SURFACES OF MATING PARTS ARE FREE OF DEBRIS THAT MAY COMPROMISE SEAL

(Mimosa Networks, Inc.) Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: (2ABZJ-100-00113). Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

File Name

(ie- 1100_schematics.pdf) Exhibit Type

(ie- Block Diagram, Schematics, Operational Description, Parts List, Tune Up Info) Schematic Diagram Block Diagram Operational Description FCC Software Security Requirements for UNII devices Mimosa-by-Airspan-A6-Datasheet-

DS-0023-04 The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Schematic Diagram Block Diagram Operational Description FCC Software Security Requirements for UNII devices Mimosa-by-Airspan-A6-Datasheet-

DS-0023-04 The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commissions public notice, we also request temporary confidential treatment of information accompanying this application as outlined below:

Exhibit Type

(ie- External Photos, Internal Photos, Test Setup Photos, Manual) External Photos Test Setup Photos Internal Photos User Manual File Name

(ie- 1100_external photos.pdf) External Photos Test Setup Photos Internal Photos User Manual Sincerely,

(signature)

(printed name): Jaime Fink Date: 07/13/2022 Rev 11/20/07

Datasheet Supercharged Point-to-Multipoint (PTMP) Wi-Fi 6E-Based, 8x8, Beamforming, A6 Access Point The A6 fixed wireless access point delivers up to 7 Gbps capacity, unbelievable subscriber capacity, and synchronized network scalability for unlicensed, outdoor, fixed wireless PTMP networks. The first future-proof solution delivering fiber fast gigabit speeds to subscribers via wireless, the A6 extends beyond the traditional 5 GHz band to take advantage of expanded 160 MHz channels in the new, low-noise 6 GHz band. Scalable, Low-Noise 6 GHz Band Previous OFDM-based fixed wireless solutions lacked subscriber scalability, requiring costly investment in too many AP sites, introducing massive interference in an already crowded 5 GHz band, with no noise mitigation capabilities. Superior Wi-Fi 6E Technology Armed with the latest Wi-Fi 6E technologies, including 8x8 MU-MIMO, 1024-QAM, noise fighting beamforming, massively reduced resource unit size, low-latency OFDMA, and network wide GPS sync, the A6 resets nearly every performance and scalability bar in the industry. Extreme Performance and Value Pairing these incredible innovations with brand new, interference-free 6 GHz spectrum, the A6 can deliver gigabit+ subscriber speeds needed for advanced rural broadband projects, and the high-scalability to tackle the most dense, urban NLOS areas cost effectively. 5.150-

6.425 GHz IP 7 Gbps IP67 SRS 29 dBm 8x8 MU-MIMO OFDMA 6 GHz AFC 1 Need more information?

Get in touch with the Mimosa sales team by visiting mimosa.co/contact-us. Specifications Performance Max Throughput:

7 Gbps IP aggregate UL/DL (9608 Mbps PHY) Wireless Protocols:

WiFi Interop; TDMA (future release) Radio MIMO & Modulation:

8x8 MU-MIMO;

OFDMA, BPSK-1024QAM Bandwidth:

Single or dual 20/40/80/160 MHz channels Frequency Range:

51506425 MHz Restricted by country of operation Max Output Power: 29 dBm Rx Sensitivity: @ 1024 QAM

-47 dBm @ 160 MHz

-50 dBm @ 80 MHz

-53 dBm @ 40 MHz

-56 dBm @ 20 MHz Physical Dimensions:

Height: 490 mm (19) Width: 295 mm (11.6) Depth: 75 mm (3) Weight: 3.95 kg (8.7 lbs) Enclosure Characteristics:

Outdoor UV-stabilized, engineered polymer with integrated metal mounting back Wind Survivability: 200 km/h (125 mph) Wind Loading: 39 kg @ 160 km/h (86 lbs @ 100 mph) Mounting: Dual standard pole straps for 30 mm (1.18) to 90 mm (3.54) OD pipes Network Interface2: (1) GbE copper PoE,

(2) 10 GbE SFP+ (optical) Antenna Gain: 24 dBi with adaptive beamforming Beamwidth: 90 azimuth, 7 elevation Front-to-Back Ratio: >30 dB Cross-Polar Isolation: >20 dB Polarization: Dual-linear XPIC 2 Power Max Power Consumption: 40 W System Power Method: Outdoor PoE or DC System Lightning & ESD Protection: 6 kV PoE Power Supply:

Passive PoE compliant, 4856 V (not included) Environmental Outdoor Ingress Protection Rating: IP67 Operating Temperature: -40C to +55C (-40F to 131F) Operating Humidity: 5 to 100% condensing Operating Altitude: 4,420 m (14,500) maximum Shock and Vibration: ETS 300-019-2-4 class 4M5 Features 10 Gigabit Ethernet: (2) SFP+ (optical) ports Management Services:

MMP support; Netconf (future support); SNMPv2c/v3; Syslog;

HTTPS; HTML 5 based Web GUI; IPv4 and IPv6 Smart Spectrum Management:

Active scan monitors/logs ongoing RF interference across all channels (no service impact); Dynamic auto-optimization of channel and bandwidth use Security: WPA3; AES; RADIUS; 802.1x authorization QoS: Supports 4 user-configurable QoS levels for SRS (GPS Sync) (CBWFQ); Behavior Aggregate (BA) and CoS Classifier, with user-configurable precedence VLAN: Per subscriber VLAN, Q-in-Q, triple tagging;

Management VLAN Collocation Synchronization:

1PPS GPS TX/RX synchronization for collocated co-channel radios; Adjustable up/downstream bandwidth ratio GPS Location:

GNSS-1 (GPS + GLONASS) Regulatory and Compliance Approvals:

FCC Part 15.407; IC RSS210;

CE (RED, EMCD, LVD, RoHS);

ETSI 301 893/302 502 RoHS Compliance: Yes Safety: EN 62638-1 1 Automatic Frequency Coordination database support via firmware update, once formally approved by the FCC 2 May be upgraded prior to launch for additional functionality Mimosa Networks, Inc. All rights reserved. DS-0023-04 2201 www.mimosa.co @gomimosa Datasheet A6 Mimosa, a product division of Airspan, is the global technology leader in wireless broadband solutions, enabling service providers to connect dense urban and hard-to-reach rural homes at a fraction of the cost of fiber. Mimosa was acquired in 2018 by Airspan Networks Holdings Inc. (NYSE American: MIMO), the award-winning, leading vendor of 5G software and hardware.

Mimosa Networks, Inc. 777 Yamato Road, Boca Raton, FL 33431 USA Date: 07/13/2022 FCC ID: 2ABZJ-100-00113 Model Number: A6, iBridge A6 To:

Federal Communication Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21048 To Whom It May Concern, We, Mimosa Networks, Inc. declare that this EUT (FCC ID: 2ABZJ-100-00113) will conduct FCC compliance testing, the sDOC part recognized test lab(Shenzhen NTEK Testing Technology Co., Ltd.). 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street Baoan District, Shenzhen 518126 P.R. China Please contact me if you have any question. Sincerely,

(Signed) Name: Jaime Fink Phone: 408-205-9949 Fax: 408-628-1276 Email: jfink@airspan.com

Mimosa Networks, Inc. Family models difference declaration Product Name: A6 Trade Name:

Model Name: A6, iBridge A6 FCC ID: 2ABZJ-100-00113 Difference declaration:

All the model are the same circuit and RF module, except the model names. Regards, Signature Name: Jaime Fink Date: 2022-07-13

(Mimosa Networks, Inc.) Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 07/13/2022 SUBJECT: FCC Application for FCC ID: 2ABZJ-100-00113 To Whom It May Concern:

We, the undersigned, hereby authorize Alex Li at Shenzhen NTEK Testing Technology Co., Ltd. on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Shenzhen NTEK Testing Technology Co., Ltd. on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards,

(signature)

(printed name): Jaime Fink https://airspan-my.sharepoint.com/personal/jfink_airspan_com/Documents/Airspan Downloads/FCC Letters/FCC POA Letter.docx

Date:

November, 20, 2018 Subject:

Mimosa Networks, Inc. Acquired by Airspan Networks, Inc. To Whom It May Concern, Effective November 20, 2018, Airspan Networks, Inc. has acquired Mimosa Networks, Inc. All assets of Mimosa Networks, Inc., including but not limited to all intellectual property, rights to manufacture, and Technical Bureau Certifications have been assigned and transferred to Airspan Airspan Networks, Inc. is fully authorized to manufacture Mimosa Networks, Inc. products under the Airspan brand, and utilize without limitation all current Mimosa Networks, Inc. product Technical Bureau Certifications (e.g. FCC, ETSI/CE, IC, UL, etc.) for import/export and technical compliance Networks, Inc. purposes. Best regards, Jaime Fink Chief Technology Officer & Co-Founder Mimosa Networks Inc. 469 El Camino Real Suite 100 Santa Clara, CA 95050 mimosa.co