SHB2505 blue blue Please note that the right earpiece is the Master device and the left Earpiece is the Slave device. Before the rst time use, put them into charging case to fully charge for 3 hours. Take both earpieces from the charging case, the earpiece will power on automatically. There will be a voice Power on and a voice Pairing. Then, there will be a voice R channel on right earpiece and L Channel on left earpiece after paring each other. There will be a voice Connected from Right Channel. Then, the master devices ( the right earpieces ) 3 The LED on Right earpiece ashes in white and blue for 3 mins. The LED on Right earpiece ashes in white and blue for 3 mins. There will be a voice Connected from both earpieces. You can use your device to play music or make a call. Single earbud pairing
( Mono mode) Take the right earpiece ("Master device" ) from the charging case, the earpiece will power on automatically. There will be a voice Power on and a voice Pairing". Then, there will be a voice R channel on right earpiece. Turn on the Bluetooth function on your device, search for" Philips SHB2505 tap to connect. ( Please refer to P.6 ) Once the pairing succeed, you will hear a voice" connected" And the indicator light will be o. Only Turn the Left earpiece channel power on, it cannot connect to Bluetooth device, need to turn on R Channel to pair each other. 1 Take both earpieces from the charging case, the earpiece will power on and reconnect automatically. If no device is connected, the earpieces will automatically turn o after 3 mins Take both earpieces from the charging case, the earpiece will power on and reconnect automatically 5 3 times. 3
/Left Left and hold 2 seconds and hold 2 seconds
/Left
/Left 2
/Left once. white will ashe 2 times per 3 mins Battery LED indicator on headset status It will show a battery indicator on Bluetooth device after connected to headset.
/Left Battery LED indicator on Charging case While charging earbud, Blue LED will light on One LED will light on for 0-25% power Two LED will light on for 25-50% power Three LED will light on for 50-75% power Four LED will light on for 75-100% power white 2 and white and white will 3 Battery LED indicator on Charging case with USB cable While charging earbud, Blue LED will light on One LED will ash per second for 0-25% power Two LED will ash per second for 25-50% power Three LED will ash per second for 50-75% power Four LED will ash per second for 75-100% power Put both earpieces back to charging case. Hold and press left & right earpieces function button for 5 seconds. Take both earpieces from the charging case, the earpiece will power on automatically. There will be a voice Power on and a voice Pairing. Then, there will be a voice R channel on right earpiece and L Channel on left earpiece after paring each other. The LED on Right earpiece ashes in white and blue for 3 mins. There will be a voice Connected from Right Channel. Then, the master devices ( the right earpieces ) The LED on Right earpiece ashes in white and blue for 3 mins. 3 3 60 5.0
, AAC put both earpieces back to charging case for 5 seconds and thak them out. put both earpieces back to charging case for 5 seconds and thak them out. and Left NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.