BTH600Manual BluetoothSpeakerMicrophone Model:BTH600 FCCID.:XTSBTH600 THISDEVICECOMPLIESWITHPART15OFTHE FCCRULES.OPERATIONSISSUBJECTTOTHE FOLLOWINGTWOCONDITIONS:(1)THISDEVICE MAYNOTCAUSEHARMFULINTERFERENCEAND
(2)THISDEVICEMUSTACCEPTANYINTERFERENCE RECEIVED,INCLUDINGINTERFEERENCETHATMAY CAUSEUNDESRIEDOPERATION 1PTT 2PTT 6Volumecontrolbutton 7LEDIndicators 8Clip 3Microphone 4Speaker 5LogoPlate 93.5mmjack 10PowerSwitch 11MiniUSB COMNET co., ltd./ 3F, CHISAN-No8, 7-1-3 nishinakajima, Yodogawa-ku, Osaka 532-0011, Japan 1 BTH600 BTH600StateandLEDFlashingPattern LEDMessage BTH600State&ButtonPress NoLED BothBlue&RedLEDONfor1 second RedLEDflashed3timesthen OFF Red&BlueLEDflashes alternatively BlueLEDflashesonceevery2 seconds BlueLEDflashes3timesevery3 seconds BlueLEDflashes1timeevery second Nolinkandnopaired BTH600isOFF BTH600isOFF;PressPower buttonandholdfor3seconds. BTH600ON;pressandhold powerbuttonfor3seconds BTH600isoff;Pressandhold powerbuttonfor6seconds Unpairedorlostlink StandBymode PressPTTbutton PressVolumeUp/Downunder standbymode Function BTH600OFF TurnBTH600ON TurnBTH600OFF GetBTH600intopairingmode Nolink,nopair Standby Starttotalk Makeadjustmentofvolume COMNET co., ltd./ 3F, CHISAN-No8, 7-1-3 nishinakajima, Yodogawa-ku, Osaka 532-0011, Japan 2 PairingManualforICOM 1. PreparetheBTH600andICOMradio 2. PoweronBTH600andgotopairingmode TheLEDisred/blueflashing Pressandhold6s COMNET co., ltd./ 3F, CHISAN-No8, 7-1-3 nishinakajima, Yodogawa-ku, Osaka 532-0011, Japan 3 3. PressMenuonyourICOMtoBluetooth 4. PoweronyourICOMBluetooth 5. GotoBTDeviceList COMNET co., ltd./ 3F, CHISAN-No8, 7-1-3 nishinakajima, Yodogawa-ku, Osaka 532-0011, Japan 4 6. FindDevice 7. SelectHeadset 8. Waitingforthesearching COMNET co., ltd./ 3F, CHISAN-No8, 7-1-3 nishinakajima, Yodogawa-ku, Osaka 532-0011, Japan 5 9. Youcanfindtheheadset 10. Connectit 11. Itsreadytogo COMNET co., ltd./ 3F, CHISAN-No8, 7-1-3 nishinakajima, Yodogawa-ku, Osaka 532-0011, Japan 6 DECLARATION OF CONFORMITY Model:BTH600 FCCID.:XTSBTH600 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: ( 1 ) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND ( 2 ) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION Notice : The changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void users authority to operate the device. The Federal Communication Commission Radio Frequency Interference Statement includes the following paragraph: The equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communication. However, there is no grantee that interference will not occur in a particular installation. If this equipment dose cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on , the user is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help. COMNET co., ltd./ 3F, CHISAN-No8, 7-1-3 nishinakajima, Yodogawa-ku, Osaka 532-0011, Japan 7