FCC ID: IHDT5ZX1 Mobile Cellular Transceiver

APPLICANT: MOTOROLA, INC. FCC ID: IHDT5ZX1 USERS MANUAL INFORMATION 1. The following Antenna Installation Guidelines will be shipped with each product:. ANTENNA INSTALLATION GUIDELINES IMPORTANT:

To meet the FCCs RF Exposure Guidelines, the antenna should be installed so there is at least 30 cm of separation between the occupants of the vehicle and the antenna. 2. A draft copy of the users manual follows:

EXHIBIT 8 415A79-O 9/22/99 9:39 AM Page 1 USER'S GUIDE 2950 MOBILE/CARRY PHONE Mobile Cellular Telephone 415A79-O 9/22/99 9:39 AM Page 2 Table of Contents Getting Started.....................................................4 Welcome ................................................................4 General Safety Information....................................6 Introduction ..........................................................11 Phone Overview ..................................................12 Basic Operation .................................................15 Turn Phone On and Off .......................................15 Place a Call..........................................................17 Automatic Redial..................................................18 End a Call ............................................................19 Receive a Call......................................................19 Call in Absence Indicator.....................................19 Hands Free Operation (with optional HF Microphone) ...................................................20 Place a Hands Free Call......................................20 Receive a Hands Free Call..................................20 Manual Handset to Hands Free Operation..........20 Automatic Hands Free ........................................21 Enhanced Simplex Hands Free...........................21 Signal Strength Meter ..........................................22 Volume Meter ......................................................22 Speaker Volume ..................................................23 Earpiece Volume .................................................23 Ringer Volume .....................................................24 Display Own Phone Number ...............................24 Switch to Second Phone Number........................24 Memory ...............................................................26 Storing Information in Memory ............................26 Selecting a Memory Location ..............................26 Store to a Location Number.................................26 Memory Autoload.................................................27 Storing a Phone Number and a Name ................27 1 415A79-O 9/22/99 9:39 AM Page 2 Table of Contents Memory Protect ...................................................29 Recalling/Scrolling from Memory .........................29 Recalling/Scrolling by Location Number ..............29 Last Number Recall .............................................30 Recalling Last 10 Numbers Dialed ......................30 Super Speed Dialing............................................31 Turbo Dial ............................................................31 One-Touch Dialing Keys......................................32 One-Touch Emergency Dialing............................33 Scratch Pad Memory ...........................................33 Tone Dialing (Two-Part Calling)...........................34 Pause Dialing (Memory Linking)..........................35 Edit a Memory Location.......................................37 Clear Memory Entries ..........................................38 Features ..............................................................39 Select/Cancel Menu Features .............................39 Signal Strength Meter (SSM)...............................39 Feature Status Review ........................................40 Battery Indicator...................................................40 Extended Talk Time.............................................41 Microphone Muting ..............................................41 Name Preference.................................................41 Automatic Answer ................................................42 Multiple Key Answer ............................................42 Incoming Call Screening......................................43 Silent Ringer ........................................................43 Distinctive Ringer .................................................44 Silent Keypad.......................................................45 Silent Scratch Pad ...............................................45 PIN Code Activation.............................................46 Timers ..................................................................47 Individual Call Timer ............................................47 Resettable Call Timer ..........................................47 2 Table of Contents Cumulative Call Timer .........................................48 Individual Display Timer.......................................48 One-Minute Timer ................................................49 Security Features.................................................49 Electronic Lock ....................................................49 Change Unlock Code...........................................50 Display Unlock Code ...........................................50 Automatic Lock ....................................................50 Theft Alarm ..........................................................51 Auxiliary Alert .......................................................52 Change Service Level..........................................53 Master Reset .......................................................54 Master Clear ........................................................56 Reference............................................................57 The Cellular System ............................................57 Service Area ........................................................57 Weak Signal Alert ................................................57 Switchhook and Enhanced System Services ......58 Roaming...............................................................58 Selectable System Registration...........................58 Troubleshooting ...................................................63 Quick Reference Feature Guide..........................64 Message Glossary ...............................................66 Index ....................................................................72 3 415A79-O 9/22/99 9:39 AM Page 4 Getting Started Welcome Thank you for selecting Motorola a world leader in cellular technology. All Motorola cellular phones are designed and manufactured in the United States to meet Motorolas exacting specifications and world-class quality standards. These phones withstand our rigorous durability tests including temperature, humidity, shock, dust, vibration, and a drop test. Product superiority is yours with Motorola. For information about your product or accessories for your product, please call Motorola at:

1-800-331-6456 TTY: 1-888-390-6456 1-800-461-4575 (Canada) Please visit us at:

www.mot.com For any information about your cellular service, please call your service provider (Carrier). Carriers Name ________________________ Getting Started You will need to have the following information when you inquire about your phone or service. Your ESN (electronic serial number) and MSN

(mechanical serial number) are located on the transceiver of your telephone. ESN Number_____________________________ MSN Number ____________________________ Model Number ___________________________ Cellular Phone Number ____________________ Unlock Code The sequential code of 123 is the standard unlock code programmed into all phones by the factory. It is often changed to the last three digits of your cellular phone number by the carrier. For easy access to this unlock code in the future, please list it here now: __ __ __.

(Please contact your place of purchase if your unlock code has been changed and you do not have this information.) Carriers Phone Number_________________ Warranty Expiration Date ________________ Date of Purchase ______________________ 4 5 415A79-O 9/22/99 9:39 AM Page 6 Getting Started General Safety Information IMPORTANT Safety Information For Wireless Mobile Phones Exposure to Radio Frequency Signals Your wireless mobile telephone is a low power radio transmitter and receiver. When it is ON, it receives and also sends out radio frequency (RF) signals. In August, 1996, the Federal Communications Commissions (FCC) adopted RF exposure guidelines with safety levels for wireless phones. Those guidelines are consistent with the safety standards previously set by both U.S. and international standards bodies:

ANSI C95.1 (1992)*

NCRP Report 86 (1986)*

ICNIRP (1996)*

Those standards were based on comprehensive and periodic evaluations of the relevant scientific literature. For example, over 120 scientists, engineers, and physicians from universities, government health agencies, and industry reviewed the available body of research to develop the ANSI Standard (C95.1). The design of your phone complies with the FCC guidelines (and those standards) when used as described under Phone Operation.

*American National Standards Institute; National Council on Radiation Protection and Measurements; International Commission on Non-

Ionizing Radiation Protection. 6 Getting Started Phone Operation Do not operate your mobile telephone when a person is within 4 inches (10 centimeters) of the antenna. A person or object within 4 Inches (10 centimeters) of the antenna could impair call quality and may cause the phone to operate at a higher power level than necessary and expose that person to RF energy in excess of that established by the FCC RF Exposure Guidelines. Antenna Care Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could damage the phone and may violate FCC regulations. Driving Check the laws and regulations on the use of wireless telephones in the areas where you drive. Always obey them. The use of these devices may be prohibited or restricted in certain areas. Also, if using your phone while driving, please:

Give full attention to driving -- driving safely is your rst responsibility;

Use hands-free operation, if available;

Pull off the road and park before making or answering a call if driving conditions so require. Electronic Devices Most modern electronic equipment is shielded from RF signals. However, certain electronic equipment may not be shielded against the RF signals from your wireless phone. 7 415A79-O 9/22/99 9:39 AM Page 8 Getting Started Pacemakers The Health Industry Manufacturers Association recommends that a minimum separation of six (6) inches be maintained between a wireless phone antenna and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with the independent research by and recommendations of Wireless Technology Research. Persons with pacemakers:

Should ALWAYS keep the phone antenna more than six inches from their pacemaker when the phone is turned ON;

If you have any reason to suspect that interference is taking place, turn your phone OFF immediately. Other Medical Devices If you use any other personal medical device, consult the manufacturer of your device to determine if they are adequately shielded from external RF energy. Your physician may be able to assist you in obtaining this information. Turn your phone OFF in health care facilities when any regulations posted in these areas instruct you to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy. Vehicles RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles. Check with the manufacturer or its representative regarding your vehicle. You should 8 Getting Started also consult the manufacturer of any equipment that has been added to your vehicle. Posted Facilities Turn your phone OFF in any facility where posted notices so require. Aircraft Airline regulations prohibit using your phone while in the air. Switch OFF your phone before boarding an aircraft. Blasting Areas To avoid interfering with blasting operations, turn your phone OFF when in a blasting area or in areas posted: Turn off two-way radio. Obey all signs and instructions. Potentially Explosive Atmospheres Turn your phone OFF and do not remove the battery when in any area with a potentially explosive atmosphere and obey all signs and instructions. Sparks, from your battery, in such areas could cause an explosion or fire resulting in bodily injury or even death. Areas with a potentially explosive atmosphere are often but not always clearly marked. They include

(but are not limited to) fueling areas such as gasoline stations; below deck on boats; fuel or chemical transfer or storage facilities; areas where fuel odors are present, i.e. if a gas/propane leak occurs in a car or home; areas where the air contains chemicals or particles, such as grain, dust, or metal powders; and any other area where you would normally be advised to turn off your vehicle engine. 9 415A79-O 9/22/99 9:39 AM Page 10 Getting Started For Vehicles Equipped with an Air Bag An air bag inflates with great force. DO NOT place objects, including both installed or portable wireless equipment, in the area over the air bag or in the air bag deployment area. If in-vehicle wireless equipment is improperly installed and the air bag inflates, serious injury could result. Getting Started Introduction The cellular telephone you have selected represents the state-of-the-art in cellular telephones today. The listing below shows just a few of the exceptional features that your telephone provides. Seven-character 14-segment LCD display 104 memories, including last number recall and scratch pad Three One-Touch Dial Keys Auto Answer Five Call Timers Two-system Registration Multiple Key Answer Distinctive Ringer Tones To help you become familiar with your telephones features, this manual will take you through a logical step-by-step learning procedure. The tabs at the edge of the manual mark the different categories that the telephones operations have been broken into. The respective sub-categories are noted in black bars. 10 11 415A79-O 9/22/99 9:39 AM Page 12 Getting Started Phone Overview Operating Display and Status Indicators Provide a visual indication of telephone numbers and messages associated with mobile telephone service. Power Light Displays when a call is in progress. In Use Displays when a call is in progress. No Svc Displays when the unit is out of service range of a cellular system. Calls cannot be placed or received. Roam Displays when the unit is within range of a cellular system other than your home registered system. Three One-Touch Dialing Keys Allow direct access to important phone numbers and carrier network services. Volume Keys Adjust earpiece, ringer, and speaker volume. Also:

G scrolls forward. H scrolls backward. Getting Started Fcn K E F C 3 D L 6 M V 9 W N O X Y Z U B H 1menu 2 A I 5 J 4 G S 8 T 7 P 0opr Q R Recall Clear SEND Power Store END 12 13 415A79-O 9/22/99 9:40 AM Page 14 Getting Started Control Keypad R Recalls and displays telephone numbers stored in memory. C Clears the last digit entered when pressed and released. Press and hold to clear the entire display. S Initiates a call or answers a call. P Turns the phone on and off. s Stores telephone numbers into any of the memory locations. E Terminates a call in progress. F Function Key Used in combination with other buttons for specific user-programmed functions (e.g., F, 5 activates lock mode). Basic Operation Turn Phone On and Off 1. If installed in your vehicle, your phone should turn on and off with the vehicles ignition. If it does not, or if the phone is in a bag conguration, press P . 2. Press P again to turn unit off. Start-up Self Tests Each time the telephone is turned on, it performs a series of self tests, sounds a tone, and lights all display positions and status indicators to check their operation. Display Messages Message Explanation Explanation A1 B1 A2 B2 LOCKED If your phone is programmed for two cellular systems, one of these messages will appear in the display upon power up. These are reminders as to which system and phone number are currently in use. Indicates that the phone has been locked and cannot send or receive calls until unlocked. Refer to page 49, "Electronic Lock". 14 15 415A79-O 9/22/99 9:40 AM Page 16 Basic Operation Start-up Status Indicators Indicators Explanation In Use No Svc Roam In Use No Svc Roam In Use No Svc Roam In Use No Svc Roam On/Lock Indicator

(dot) Lights steadily to indicate the phone is on and fully operative Lights steadily to indicate the phone is locked and will not place calls In Use Indicator Lights steadily while a call is in progress No Svc (No Service) Indicator Lights steadily if phone is beyond range of a cellular service area Calls cannot be placed or received while No Svc is lit Roam Indicator If flashing, you are accessing a service area outside of your home system. Steady Illumination Roaming on a home type system Flashing Roaming on a non-home type system 16 Basic Operation Place a Call 1. With power on, enter the number you wish to call. 2. Press S. (You may leave the handset mounted while dialing if an external microphone is present.) The IInn UUssee indicator will illuminate. Once your party answers, bring the handset to your ear. Or leave the handset mounted and direct your conversation to the Hands Free microphone (if present) for a hands free call. To Correct an Error To clear the last digit entered, press and quickly release C. To clear the entire entry, press and hold C until the entire entry is erased. If Entering More Than Seven Digits You can call a phone number with up to 32 digits, but only the last seven digits will display. When recalling a stored phone number that is longer than seven digits, the display will flash the memory location number and the last ten digits of the number. EXAMPLE Recall memory location 01 that contains the 14-digit number 12345678901234. 01567/ 8901234will alternately display. To review the overflow digits from the above example, press R. The phone will take you back to the beginning of the phone number, then flash up to seven digits at a time 1234567 / 8901234 until the end of the stored phone number is reached. 17 415A79-O 9/22/99 9:40 AM Page 18 Basic Operation Unsuccessful Call Attempts If you hear one of the following signals, you have not successfully completed your call. Tone Tone Fast Busy

(reorder signal) System Busy Alternating High/Low Tone

(intercept) No Service Slow Busy Signal Description Cellular System Busy Press S again before ending the unsuccessful call attempt to automatically redial the call (see

"Automatic Redial", below), or press E and dial the call again. Cellular System Could Not Complete the Call You may have tried to place a call before the ON/LOCK indicator was lit to let you know your phone was fully operative. Either press S again to redial, or press E and dial the call again. Called Partys Line is Busy Automatic Redial Your telephone includes a convenient feature designed to make repetitive call attempts when a cellular system is busy. If you receive an alternating high/low signal

(intercept) or the fast busy tone (reorder signal) followed by snd to redial in the display when attempting to place a call and wish to retry the call, press S before ending the unsuccessful call attempt. Redial is then displayed. Your telephone will make the call attempt continuously over the next four minutes. If four 18 Basic Operation minutes is insufficient time, press S to begin another cycle. If the call attempt is successful, the phone will ring to alert you of the connection.You may terminate Automatic Redial by turning off the phone or by pressing E. NOTE Automatic Redial applies when the system is busy and will not engage when the called partys line is busy. End a Call Press E or return the handset to its mount. The IInn UUssee indicator will extinguish. If you have activated the Automatic Hands Free feature, you must press E to terminate the call. Receive a Call Lift the handset to your ear or press S if an external microphone is present. Power must be on to receive calls. Call in Absence Indicator If your phone is on and an incoming call is unanswered, Call is displayed. Press C or E to cancel the message and clear the display. In carry phone configuration, the display will go blank after 6 seconds in order to conserve battery energy. Reactivate the display by pressing any key except C, E, or P. NOTE The phone will not display or retrieve the phone number of the calling party. 19 415A79-O 9/22/99 9:40 AM Page 20 Basic Operation Hands Free Operation

(with optional HF Microphone) Place a Hands Free Call 1. Leaving the handset mounted, dial the number you wish to call. 2. Press S . 3. When the called party answers, direct your conversation to the Hands Free microphone typically mounted on your vehicles sun visor. The In Use indicator will remain on and HF will display for the duration of the call. 4. Press E to terminate the call. Receive a Hands Free Call 1. Press S . 2. Direct your conversation to the Hands Free microphone. The In Use indicator will remain on and HF will display for the duration of the call. 3. Press E to terminate the call. Manual Handset to Hands Free Operation 1. To switch from the handset to Hands Free operation, press F, 6. Mute will display. Note that M for Mute appears on 6. 2. Return the handset to its mount. 3. Press F, 6 again and HF will display. 4. Direct your conversation to the microphone. 20 Basic Operation Automatic Hands Free 1. Press F, 1. 2. Scroll the menu by pressing G or H until HF AUTO NOSWTCH displays. 3. Press C once to toggle this feature on, and again to toggle it off. 4. To exit the Feature Menu, press E. This feature allows you to automatically go to Hands Free operation without pressing F, 6. To switch from Hands Free to Handset operation, just lift the handset while in a call. To return to Hands Free operation, hang up the handset and begin speaking. Enhanced Simplex Hands Free In certain systems, you may experience audio feedback while using Full Duplex Hands Free operation, the normal operating mode. This situation can usually be alleviated by slightly reducing the speaker volume. In extreme cases, you may want to switch to Enhanced Simplex Hands Free operation. This operation will not allow interruption of the party that is speaking. 1. Press F, 1. 2. Scroll the menu by pressing H or G until HF PREFOFF displays. 3. Press C once to toggle this feature on, and again to toggle it off. 4. To exit the Feature Menu, press E. 21 415A79-O 9/22/99 9:40 AM Page 22 Basic Operation Signal Strength Meter The Signal Strength Meter (SSM) represents the relative strength of the signal received by your phone. The SSM is displayed as a bar graph following the letter S at the left side of the display. The S alone represents the lowest strength with each additional bar representing a stronger signal. S s = =

Weak Signal Strong Signal The SSM appears every time you turn your phone on, unless this feature is turned off through the

"Feature Menu" (refer to page 39). To best utilize the SSM, you should familiarize yourself with the relative signal strength levels and their associated call-in-progress qualities. Any messages, such as LOCKED, which display as a result of activation of a feature will take priority over the SSM. You will not see the SSM displayed in these cases. Volume Meter The Volume Meter represents the current volume setting and will display whenever you adjust the volume control. The volume level is displayed as a bar graph following the letter V at the left side of the display, with each additional bar representing a higher volume setting. Basic Operation v v = =

Lowest Volume Setting Highest Volume Setting The number of bars represents the number of volume steps for speaker, earpiece, and ringer volume. The volume levels can be adjusted by the use of G and H. Speaker Volume 1. With the handset mounted, press and hold G to raise the volume. 2. To lower the volume, press and hold H. The number of bars on the Volume Meter will decrease. The maximum number of bars that will display is four. v= =

Earpiece Volume Lift the handset and use G and H as described above. The maximum number of bars that will display is five. v= =

22 23 415A79-O 9/22/99 9:40 AM Page 24 Basic Operation Ringer Volume Press F and use G and H as described in the "Volume Meter" on page 23. The maximum number of bars that will display is six. v= =

Display Own Phone Number 1. Press R, #. The phone number that is currently active will be displayed. 2. When you have nished viewing, press C. Switch to Second Phone Number 1. Press R, #, s. The display will go blank to confirm the switch and the newly activated number will display. 2. When you have nished viewing, press C. Your telephone can operate over two different home systems, if you have made proper arrangements with your Cellular System Operator. Both are designated as your "home system" but are accessed with separate telephone numbers. While you may switch from one system to the other, only one of the two can be active at any given time. Calls are placed and received through the active system only. Basic Operation If you have two phone numbers programmed into your phone, each time the telephone is turned on, it displays a message indicating which home system type and phone number is currently active. The message shows the system type and phone number applied, as follows:

System Type and Phone Number Non-wireline or A type with phone number 1 Non-wireline or A type with phone number 2 Wireline or B type with phone number 1 Wireline or B type with phone number 2 Display A1 A2 B1 B2 If a call is placed to the inactive phone number, the caller will receive the recorded "Not In Service"

message. When you turn your phone on, the telephone will remember which system was active when you turned it off. That system will stay active until you change to the other system with the sequence R,

#, s. However, you cannot switch systems during a call. 24 25 415A79-O 9/22/99 9:40 AM Page 26 Memory Memory Storing Information in Memory Memory Autoload Your telephone provides memory capable of storing up to 99 frequently called phone numbers as well as a seven-character name tag. Upon entering a phone number in memory, the phone will prompt you to store an associated name. If you are not interested in creating a name tag for the selected location, alpha entry may be bypassed and the phone number alone can be stored. Selecting a Memory Location There are two ways to select a memory location:

select a specific location number autoload to store the information in the next sequentially available location. Store to a Location Number 1. Enter phone number to be stored, up to 32 digits. 2. Press s. 3. Enter the two-digit location number in which you wish to place the entry. 4. The phone is automatically in Alpha Entry Mode. Enter a name, or bypass Alpha, go to step 5. 5. Press s. Phone will confirm storage by displaying memory location number. NOTE If FulLdisplays, refer to "Memory Protect"

on page 29. 2266 1. Enter phone number to be stored. 2. Press s, *. 3. The phone is automatically in Alpha Entry Mode. Enter a name or continue to step 4. 4. Press s. Phone will confirm storage by displaying the autoload memory location number. NOTE If FulLdisplays, refer to "Memory Protect"

on page 29. This procedure automatically stores memory entries into the next available memory location. This method serves particularly well if you do not remember the next available memory location. Storing a Phone Number and a Name 1. Enter phone number to be stored. 2. Press s. 3. Enter two-digit location number or press *

for Autoload. The phone will then automatically prompt for alphabetic name input. The Alpha Entry Mode display will flash ALPHA . 4. Utilize the alphanumeric keypad to enter up to 7 letters as described in the example on page 28. # advances to the next position.

* backspaces, if necessary. Repeat until name tag is complete. 5. Press s. Phone will confirm storage by displaying memory location number. 27 415A79-O 9/22/99 9:40 AM Page 28 Memory NOTE Your phone is capable of storing up to 32 numeric characters or a combination of 16 numeric and seven alpha characters per memory location. Details on Utilizing Alpha Entry Mode Once in Alpha Entry Mode, you can enter letters using your numeric keypad. For example, "A" is at the first press of 2, "B" is at the second press of 2, and "C" is at the third press of 2. Key 1st Press 2nd Press 3rd Press 4th Press 2 3 4 5 6 7 8 9 A D G J M P T W B E H K N Q U X C F I L O R V Y S Z EXAMPLE To enter "Bob" and his phone number 555-1234 into memory location 01:

1. Enter phone number by pressing 5, 5, 5, 2. Press s, 0, 1. The display will flash 1, 2, 3, 4. ALPHA . 3. Press 2twice to select "B". Press #to advance to the next position. Press 6three times for "O". Press #. Press 2twice more to select the second "B". 28 Memory 4. Press s.The display will flash 01to confirm that the name and phone number were successfully stored in memory location 01. NOTE If FulLdisplays, refer to "Memory Protect"

below. Memory Protect The directory has an automatic memory protect feature which prevents the accidental overwriting and loss of previously stored names and numbers in memory. If you attempt to store a number or name in a location that already contains an entry, the phone will display FULL, and the name/number in that memory location. The display will then alternate between the previously stored number and CHANGE?. If you wish to save to that location, thus erasing the old information, press s. If you wish to store the entry in an alternate location, Press E, s and the alternate location number. Recalling/Scrolling from Memory Information stored in memory can be recalled or reviewed by location number. You may also scroll the memory during a call. Pressing E once in this case will cancel scrolling, but not the call. Recalling/Scrolling by Location Number 1. Press R. 2. Enter the desired two-digit location number. or 29 415A79-O 9/22/99 9:40 AM Page 30 Memory Press 0, 1 and press # or G to begin scrolling from the beginning of the stored locations. The display will show the location number, then the first ten digits of the number. If Name Preferred is selected, up to seven characters of the name will display. (Refer to "Name Preference" on page 41 for more details.) 3. Press S to place a call to the number displayed. Use G and H to scroll forward and backward. To scroll from a specific two-digit location, press R, then the location number where you wish to begin scrolling. The phone will display an apostrophe () after the memory location number to indicate that memory scrolling is active. Last Number Recall 1. Press R, and the last number entered on the keypad will appear. 2. Press S to place a call to the last number displayed. Recalling Last 10 Numbers Dialed 1. Press R, 0, 0. The display will show L0 followed by the name or number of the most recently placed call. 2. Scroll the last ten numbers dialed with *

and #. 3. To place a call to this number, press S. 30 Memory This feature allows you to refer to or redial any of the last ten numbers to which calls were placed. The numbers are stored in the order placed and always represent the ten most recent calls. Successive calls to the same number are stored only once, and all are retained when the unit is shut off. NOTE When scrolling, you may observe that a location number is skipped. This may be caused by pressing Swhen the display is empty and does not mean that a number has been lost. Super Speed Dialing 1. Enter the location number. 2. Press S. Memory locations 1-99 are equipped with Super Speed Dialing capability. Once information is stored in these locations, Super Speed Dialing allows you to place a call without pressing R. The number dialed will not display for review. NOTE Do not attempt the sequence 0, S. This will place a call to the local operator. Turbo Dial Press and hold for one second any one of the digit buttons 2 through 9. The digit buttons 2 through 9 (1 is reserved for Emergency Dialing) provide an advanced form of Super Speed Dialing. Once numbers have been stored in memory locations 2-9, calls can be placed from these locations by pressing the 31 415A79-O 9/22/99 9:40 AM Page 32 Memory associated key and holding for approximately one second. There is no need to press S. NOTE If you wish to use memory location 1 for a non-emergency number, the Emergcy message may be deactivated through the "Feature Menu"

found on page 39. In order to prevent the accidental pressing of these keys, Turbo Dial can be deactivated through the feature menu also. NOTE Turbo Dialing is affected by "Call Restriction" Service Levels 1, 2, and 3. See

"Change Service Level" found on page 53. Do not select these service levels if you wish to use Turbo Dialing. One-Touch Dialing Keys Your phone has three special dialing keys, A, B, D, which allow for easy one touch access to numbers stored in these locations. To store a number:

1. Enter phone number to be stored. 2. Press s. 3. Press specic one touch key. 4. The phone is automatically in Alpha Entry Mode. Enter a name or bypass by pressing s. Phone will confirm storage by displaying Stored. To place a call:

1. Press and hold the One-Touch Dial Key A, B, or D. These keys function like Turbo Dial keys. When you press and hold A, B, or D, a call is Memory placed to the number stored in that position. To recall the number, press R, and the specific One-Touch Key. To clear the number, press C, s, and the specific One-Touch Key. ALPHA will display. Press s. The unit will display the name and number along with the prompt CHANGE?. Press s to clear both name and number. STORED will display to indicate that the number has been cleared. One-Touch Emergency Dialing 1. Press and hold 1. EMERGCY will display. Memory location 01, a Turbo Dial location, may be used for 911 or any other emergency number you may wish to dial even if your phone is locked. Emergency dialing can be deactivated by using the "Feature Menu" found on page 39. When this feature is deactivated, the number stored in memory location 01 will still be dialed if the phone is unlocked and if you press and hold 1, but EMERGCY will not display. NOTE Do not select Call Restriction Service Levels 1, 2, or 3 if you wish to use One-Touch Emergency Dialing. NOTE Automatic Redial does not work with emergency dialing while the phone is locked. Scratch Pad Memory The scratch pad permits entry of numbers from the keypad during conversation. 32 33 415A79-O 9/22/99 9:40 AM Page 34 Memory If your party gives you another number to call, simply enter this from the keypad. If you make an error, press C to erase the last digit entered or hold C to erase the entire entry. Advise your party that they will hear tones as you store the number. To call the scratch pad number at the end of an ongoing conversation, press E, S. NOTE Refer to "Silent Scratch Pad" on page 45 for details on silencing the tones. Tone Dialing (Two-Part Calling) Your telephone provides the standard Dual Tone Multi-Frequency (DTMF) signals typically used to access alternate long distance services, signal pagers, answering machines, etc. Generally, these services use a two-part procedure: First, a call is placed from the memory or through the keypad to a central telephone number.Then a secondary dial tone is heard, and the additional tone digits are sent. To tone dial from the keypad Enter the desired number and press S. Append additional digits using the keypad once prompted. The tones are automatically sent as you press the keys. Do not press S again. EXCEPTION If you have selected silent scratch pad, you must press R, safter entering the additional digits. To tone dial from a memory location, recall from memory the number you wish to send using R , location number. Then press S. To send additional groups of numbers recall the location number and press R , S. Repeat as needed. 34 Memory Two-part calling can be automated by a unique feature which permits the programming and pauses between groups of numbers. When recalled or sent, the telephone stops transmitting at the pause and waits for your response (i.e., secondary dial tone). Pause Dialing (Memory Linking) 1. Enter the rst group of numbers from the keypad or recall them from memory using R. 2. Insert a pause by pressing F, S. insert paus will appear. Press s and a will display where the pause in inserted. 3. Enter the next group of numbers, or recall them from memory by pressing F, R, two-digit location number. 4. Repeat this sequence for as many groups as you wish up to a maximum of 32 digits.

(Each pause occupies a digit.) EXAMPLE To construct a number sequence which you might use to inquire about your bank balance, follow this example. The entry sequence required by the bank is to call the access number, wait for the tone, enter your ID number followed by #, wait for the tone, then enter your account number followed by #. The banks telephone number is 123-4567. Your ID number is 888. Your account number is 22. 35 415A79-O 9/22/99 9:40 AM Page 36 Memory 1 2 3 4 5 6 Instruction and Key Sequence Display Enter the phone number of the bank 1, 2, 3, 4, 5, 6, 7 or recall it from memory location xx R, x, x Create a pause F, S, s Enter the ID number and a pound sign 8, 8 8, #

or recall it from memory location xx F, R, x, x Create another pause F, S, s 1234567 234567 67888C 7888C Enter the account number and a pound sign 2, 2, #

88C22C To store number, press s and the Memory Location or One Touch Key. Press s again to bypass Alpha display. The memory location number will be displayed to confirm storage. If you stored the number in a One Touch Dial location, STORED will be displayed to confirm storage. ALPHA To place a linked call, press S to transmit the first group of numbers, prior to the first pause. (If your number is stored in a One-Touch Dialing Key or a Turbo Dial location, simply press the key.) After waiting for the system response, press R, S to 36 Memory send the second group of numbers. Continue to press R, S until all digit groups are sent. If the PIN code feature is activated the PIN code will automatically be sent after the first pause by pressing S. NOTE Do not add the PIN code to the linked sequence. Your phone will automatically insert the PIN code when placing a linked call. Follow the instructions in "PIN Code Activation" on page 46. Edit a Memory Location 1. Press R and the two-digit location number. 2. Press R again, if name only displays, so that the phone number to be changed is displayed. 3. Edit phone number by pressing C to back out the digits to be changed. Enter new digits. 4. Press s and the same two-digit location number. The display will flash ALPHA and then the name you have stored or if no name is stored. 5. Change or add alpha name tag if desired. To edit name, press C to back out the letters to be changed. Enter new alpha characters.

(Enter alphabetic characters as described on page 28.) 6. Press s . 37 415A79-O 9/22/99 9:40 AM Page 38 Memory 8. You will see a Memory Protect message;

press s to overwrite. Memory location number will display as confirmation. NOTE See "Name Preference" on page 41 for more details on step 2. Clear Memory Entries 1. Press C, s, and the two-digit location number to be cleared. 2. The phone will display ALPHA . Press s to bypass. The phone will display Full, flash number in memory, followed by Change?. 3. Press s to clear. or Features Additional features that may be available with your phone but are not accessed through the feature menu, are also described in this section. Select/Cancel Menu Features 1. Press F, 1. 2. Scroll the menu by pressing H or G until the desired feature displays. 3. Press C to change the status of the displayed feature between on and off. 4. Press E to exit the Feature Menu. EXAMPLE To activate silent keypad, press F, 1, and scroll with #or Guntil the display shows KEYPAD TONE ON. Press C to activate this feature. The display will then show KEYPAD TONEOFF. Press Eto exit the menu. Press E to exit without deleting the entry. Signal Strength Meter (SSM) To Disable the SSM from Displaying 1. Press F, 1. 2. Scroll the menu by pressing H or G until SIGNAL MTR ON displays. 3. Press C once to disable the SSM, again to re-enable. 4. Press E to exit the Feature Menu. Once the SSM is disabled, on will appear in place of the s = =

See "Signal Strength Meter" on page 22 for more details. 39 38 415A79-O 9/22/99 9:40 AM Page 40 Features Feature Status Review To Review Status 1. Press F, 0, 9, R. 2. Press G or H to scroll through activated features. To End Review Press E. Status review permits you to scroll through your operating settings for your reference. Listed on the page 60 are the status messages you may see if any advanced features are selected or changed from their standard setting. Battery Indicator If your cellular telephone is being used in a carry phone configuration, Press F, 4 to display a battery indicator. This allows you to review the battery charge level. The battery indicator is displayed as a bar graph. The B alone represents the lowest voltage with each additional bar representing a stronger charge. B ==

NOTE In the carry phone configuration, the display will go blank after six seconds. You may reactivate the display by pressing any key except P. Features Extended Talk Time The extended talk time feature allows you to conserve battery power when operating in a strong signal area. To enable this feature, refer to "Feature Menu" on page 39. Microphone Muting To mute microphone while in a call:

Press F, 6. To disable mute while in a call:

Press F, 6 again. This feature allows you to confer privately with others in the car during a call. It will disable the microphone and display Mute. Note that M for Mute appears on 6. The mute feature is canceled if you end your call. Name Preference 1. Press F, 1. 2. Scroll the menu by pressing H or G until NAME PREFOFF displays. 3. Press C once to toggle this feature on, and again to toggle it off. 4. To exit the Feature Menu, press E. The Name Preference feature reverses the display order of memory entries so that the name will be displayed before the number. 40 41 415A79-O 9/22/99 9:40 AM Page 42 Features Features Automatic Answer Incoming Call Screening 1. Press F, 1. 2. Scroll the menu by pressing H or G until AUTO ANSROFF displays. 3. Press C once to toggle this feature on, and again to toggle it off. 4. To exit the Feature Menu, press E. This feature permits you to answer calls without pressing S. When your phone receives a call, it will ring twice, then answer the call. NOTE We suggest that you do not select the Automatic Answer and Silent Ringer simultaneously since incoming calls will then be announced only by the flashing Call in the display. Also, this feature may be incompatible with certain enhanced system services, such as no-answer transfer. Consult your Cellular Service Provider. Multiple Key Answer 1. Press F, 1. 2. Scroll the menu by pressing H or G until MULTKEY ANSROFF displays. 3. Press C once to toggle this feature on, and again to toggle it off. 4. To exit the Feature Menu, press E. The Multiple Key Answer feature allows you to answer an incoming call by pressing S or any digit key 1 though 9. 1. Press F, 1. 2. Scroll the menu by pressing H or G until CALL RCV ON displays. 3. Press C once to toggle this feature on

(call rCv off). 4. To exit the Feature Menu, press E. Use this feature if you prefer not to receive incoming calls but wish to be informed of the attempt. When the phone is on and this feature is selected, incoming calls are signaled by several short bursts of tone, Call in the display, and the black on indicator. The caller will receive the "Not in Service" recording. As a reminder that incoming call screening is selected, the unit will sound the special tone burst each time it is turned on. NOTE We suggest you do not select Incoming Call Screening and Silent Ringer simultaneously, since the incoming call will not be signalled by a short burst of tone. Silent Ringer 1. Press F, 1. 2. Scroll the menu by pressing H or G until RINGER ON displays. 3. Press C once to toggle this feature on,

(ringer off) and again to toggle it off. 4. To exit the Feature Menu, press E. 42 43 415A79-O 9/22/99 9:40 AM Page 44 Features The telephones ring tones may be silenced where they could prove a distraction, as during a business conference, etc. In this case, incoming calls are announced only by a flashing Call in the display. NOTE We suggest you do not select the Silent Ringer and Automatic Answer simultaneously, since the phone will then answer a call without audible indication. Distinctive Ringer This feature allows you to select one of nine different ringer styles to differentiate when your phone is ringing. When selected, the phone will give you a brief sample of that ringer style. 1. Press F, 1. 2. Scroll the menu by pressing H or G until Ringer Style displays. 3. Press C once to select this feature. The selected ringer will sound as an example of this ringer style. The ringer style will display Select 1-9. 4. Press 1 - 9 to sample the different ringer styles. 5. Press * or # to scroll through the ringer styles. The display will show the number of the selected ringer style. 6. Press s to select the desired ringer style. The display will show: Ringer X Set where the X is the number of the ringer style selected. 7. Press E to exit the menu. 44 Features Silent Keypad 1. Press F, 1. 2. Scroll the menu by pressing H or G until KEYPAD TONEOn displays. 3. Press C once to toggle this feature on,

(keypad tone off) and again to toggle this feature off. 4. To exit the Feature Menu, press E. When selected, this feature silences the tones used to indicate keypad depressions. Silent Scratch Pad 1. Press F, 1. 2. Scroll the menu by pressing H or G until SCRPAD TONE ON displays. 3. Press C once to toggle this feature on, and again to toggle it off. 4. To exit the Feature Menu, press E. Use this feature to enter scratch pad numbers during a call without transmitting tones. You will hear the tones, but your called party will not. NOTE Should you wish to transmit DTMF tones

(to access answering machines, pagers, automatic menus, etc.) while Silent Scratch Pad is activated, enter the digits and press R, S. 45 415A79-O 9/22/99 9:40 AM Page 46 Features PIN Code Activation Activate PIN Code 1. Press F, 1. 2. Scroll the menu by pressing H or G until PIN INACTIV displays. 3. Press C once to toggle this feature on, and again to toggle it off. 4. To exit the Feature Menu, press E. Store PIN Code in Memory Location 07 1. Enter PIN code. 2. Press s. 3. Press 0, 7. Place a Call With PIN Code Active 1. Enter number to be called, or recall from memory. 2. Press S. Wait for double tone beep, beep. 3. Press S. The phone will automatically send the PIN code stored in memory location 07. Your cellular carrier may require a personal identification number (PIN) when placing outbound calls. This code assures the cellular system that the person placing the call is an authorized user. Ask your cellular service provider if this is required in your system. Only select this feature if your cellular service provider requires it. This feature will allow you to automatically send your PIN code with all outbound calls. If Invalid PIN displays, check to see if you have activated the feature in the menu without storing a PIN Features number in memory location 7. The PIN code must be less than seven digits. If you enter a service area which does not require a PIN code, disable the feature in the feature menu. Timers Call timers provide a useful means of monitoring the air-time spent in conversation. Several of these operate in the background and can be displayed at any time. Another offers beep tones heard only on your side of the conversation. Each timer begins counting as a cellular channel is assigned, or when the phone rings to signal an incoming call. If an incoming call is not answered, the timers revert to their previous values. Individual Call Timer To Display the Time of Your Last Call Press R, #, #. This timer accumulates the air-time of a call in minutes and seconds. It automatically resets before a new call is placed and when the phone is turned off. Resettable Call Timer To Display Press R, #, #, #. To Reset Press F, 0, 7, C. 46 47 415A79-O 9/22/99 9:40 AM Page 48 Features This timer accumulates the air-time in minutes from the point at which it is reset. This resettable timer is generally utilized to track monthly air-time usage and is set in conjunction with the monthly billing cycle. NOTE If you have two phone numbers programmed in your phone, each phone number has its own resettable call timer. To view the resettable call timer associated with the other phone number, switch your phone to that number, then use the sequence on the previous page. Cumulative Call Timer To Display Press R, #, #, #, #. This is a non-resettable timer which accumulates the phones total air-time in minutes, starting with the initial factory setting. NOTE If you have two phone numbers programmed in your phone, each phone number has its own cumulative call timer. To view the cumulative call timer associated with the other phone number, switch your phone to that number, then use the sequence above. Individual Display Timer 1. Press F, 1. 2. Scroll the menu by pressing H or G until INDIV TIMR OFF displays. 3. Press C once to toggle this feature on, and again to toggle it off. 48 Features 4. To exit the Feature Menu, press E. This feature automatically displays the accumulated time in minutes and seconds during and after each call. One-Minute Timer 1. Press F, 1. 2. Scroll the menu by pressing H or G until ONE MIN TIMROFF displays. 3. Press C once to toggle this feature on, and again to toggle it off. 4. To exit the Feature Menu, press E. This timer provides a tone ten seconds before the end of each minute during calls. Security Features Your telephone offers several forms of security against unauthorized use. These require either your three-digit unlock code, or the six-digit security code. The factory programmed unlock code is 123 and the factory programmed security code is 000000. Electronic Lock To Lock 1. Press F, and hold 5 until Lock?

displays. 2. Press s to lock. Locked will display. To Unlock Enter your three-digit unlock code. If you make an error, press C and start again. 49 415A79-O 9/22/99 9:40 AM Page 50 Features The electronic lock prevents use of the telephone by disabling both incoming and outgoing calls. To help remember which key to use, note that L for Lock appears on 5. If a call is received during this period, the phone will ring, and you must enter the unlock code before the call can be answered. Change Unlock Code 1. Press F, 0. 2. Enter your six-digit security code. 3. Enter the new desired three-digit unlock code. 4. Press s. The new unlock code will display to conrm storage. Display Unlock Code 1. Press F, 0. 2. Enter your six-digit security code. 3. Press R. The phone will display Loc and the three-digit unlock code. NOTE Use this procedure if you have forgotten your current three-digit unlock code. Automatic Lock 1. Press F, 1. 2. Scroll the menu by pressing G or H until AUTO LOCKOFF displays. 3. Press C once to toggle this feature on, and again to toggle it off. 4. To exit the Feature Menu, press E. This feature automatically locks your phone each time it is turned off. 50 Features Theft Alarm To Select (On) 1. Press F, 1. 2. Scroll the menu by pressing G or H until THEFT ALRMOFF displays. 3. Press C once to toggle this feature on, and again to toggle it off. 4. Press E to exit the feature menu. The phone will display Armed. 5. Enter the phone number to be called or recall a number from memory. 6. Turn off the phone by pressing P. To Cancel (Off) 1. Turn on the ignition. 2. Enter your three-digit unlock code within 30 seconds. When the theft alarm is selected, and an unauthorized person turns on your phone and does not enter your unlock code within 30 seconds, an alerting call will be placed to the phone number you have stored in this feature. If the phone receives a busy signal, it will repeat the call automatically. Anyone answering the call will hear alternating high and low pitched tones (siren). The removal of the control unit will not prevent your mobile telephone from attempting to place the call. However, if the antenna has been removed, the phone will be prevented from successfully completing the call. 51 415A79-O 9/22/99 9:40 AM Page 52 Features NOTE If you inadvertently trip the theft alarm and the alarm call is placed, you can stop the alarm by entering your three-digit unlock code. This feature must be reset in the feature menu each time the phone is disarmed. If the PIN code is activated, the theft alarm will not work as the PIN code must be sent manually in order to complete a call. Auxiliary Alert (mobile congurations only) 1. Press F, 4 with the unit on, unlocked, and Theft Alarm and Silent Ringer inactive. ALERT will display. 2. Turn off the vehicle ignition. The Auxiliary Alert feature allows an additional alerting device (horn or lights) to be activated for the first five rings (20 seconds) of an incoming call. This is useful if you intend to be outside of the vehicle and expect a call. NOTE A call cannot be in progress when you enable Auxiliary Alert. Auto Answer is disabled during Auxiliary Alert. Features The Auxiliary Alert mode is automatically disabled the next time the ignition is turned from off to on. The Auxiliary Alert mode can also be disabled by pressing P or by pressing F, 4 again. ALERT will turn off when the feature is disabled. Change Service Level 1. Press F, 0. 2. Enter your six-digit security code. 3. Enter the number of the service level you wish to use. 4. Press s. The phone will display Level and the number selected. Your telephone can be set to restrict call placement (as when lending the phone to another person). Using the six-digit security code, you may select one of the levels of restriction shown on the page 54. When the Auxiliary Alert mode is enabled, the mobile telephone remains on despite the vehicle ignition being turned off. Calls may be placed while in the Auxiliary Alert mode unless the unit has also been locked subsequent to pressing F, 4. 52 53 415A79-O 9/22/99 9:40 AM Page 54 Features Restrictions Level No restrictions (Standard setting) Full keypad and directory dialing No storage in directory locations 1-10 or One Touch Dial locations Keypad dialing only No directory or Turbo Dial access Phone will place calls from all directory locations (R, 0 1 - 9 9, S). No keypad dialing. No directory change or storage. Seven-digit (local) dialing only, including directory and message calls

(if seven digits or less) Phone will place calls only from directory locations 1-10 (R, 0 1 - 1 0, S). If locations 1-10 are cleared, no outgoing calls can be made. No keypad dialing. No directory or One Touch Dial storage. 4 6 3 2 5 1 To change the phone to unrestricted operation, use the procedure above and enter service level 4. Master Reset CAUTION Once begun, this procedure cannot be canceled or reversed. 1. Press F, 0. 2. Enter your six-digit security code twice. 3. Press 1, s. Features This feature allows you to reset most or all the user selectable options to their standard settings. Master reset will perform the functions listed below. Master Reset will Perform these Functions Pg. Cancel Automatic Hands Free Cancel Automatic Answer Cancel Individual Display Timer Cancel Automatic Lock Cancel Incoming Call Screening Cancel Multiple Key Answer Cancel Name Preference Feature Cancel One-Minute Timer Cancel Silent Scratch Pad Cancel Theft Alarm Reinstate Emergency Message Reinstate Keypad Tones Reinstate Signal Strength Meter Reinstate Ringer Tones Reinstate Turbo Dialing Reset Service Level to Level #4 (Standard setting) Return System Type to Standard Cancel PIN Activation 21 42 48 50 43 42 41 49 45 51 33 45 39 43 31 53 58 46 54 55 415A79-O 9/22/99 9:40 AM Page 56 Features Master Clear CAUTION Master Clear performs all the functions of Master Reset, in addition to erasing all names and numbers stored in memory, and clearing the Resettable Call Timer. Once begun, this procedure cannot be canceled or reversed. 1. Press F, 0. 2. Enter your six-digit security code twice. 3. Press 9, s. Busy may display. 4. Wait for this to clear before using the phone. It may take several minutes, depending on how full your memory is. Do not turn the phone off during this operation. 56 Reference The Cellular System There are generally two types of cellular systems serving any metropolitan area. One of these will most likely be operated by the telephone company that provides telephone service to your community, generally referred to as a wireline carrier. The other cellular service provider is a radio common carrier, referred to as a non-wireline carrier. Your Cellular Service Operator will provide information concerning specific features, procedures, and coverage in your particular area. Service Area The area within which the telephone operates is defined by your cellular service provider. Since this is a radio system, no exact boundaries (as on a map) can be drawn. The black NNoo SSvvcc (No Service) lights if you are beyond range of a service area. There may be locations within your area, such as tunnels and underground parking facilities, where the phone may act as if it were beyond range. Weak Signal Alert If you are called while in a location the system determines is inadequate for high quality service, you may hear a series of beeps to inform you of the call attempt. The caller will receive the recorded "not in service" message, Call will display, and the black on indicator will flash quickly. If this occurs, you must press C before the phone will operate. Most systems do not impose air-time charges for such call attempts. 5577 415A79-O 9/22/99 9:40 AM Page 58 Reference Switchhook and Enhanced System Services Press S. During a call, pressing S performs a switchhook function used to access enhanced Cellular System features, such as call waiting and conference calls. For the functioning of these features with S, consult your Cellular Service Provider. Roaming The term Roaming applies to the use of cellular telephones within systems other than those designated as their Home system. RRooaamm lights whenever the phone comes within range of a visited system. As your phone begins to roam, it seeks service according to the conditions you have selected. See "System Type Selection" on page 60. Steady illumination of Roam signals that your phone is accessing a home type system, while flashing indicates the phone is attempting connection through a non-home type system. Contact your system operator, or that of the visited system, for information on dialing and billing procedures. Selectable System Registration To Review Current Setting 1. Press R, *. The display will show the current active system choice. 2. Press E to exit without changing selection. 5588 Reference To Select 1. Press R, *. The display will show the current active system choice. 2. Repeatedly press * to review the system type modes. (Press E to exit without changing selections.) 3. Press s to activate the displayed selection. 4. Press E to exit. System Type Selection Your telephone seeks cellular service according to the mode you have selected. If you have selected two-system operation, the phone seeks cellular service according to the system type mode selected for each phone number. Constant flashing of RRooaamm, or a steadily lit NNoo SSvvcc while within your home service area may indicate an unintentional choice has been made. If this occurs, re-enter system type selection to see if the unit is operating in standard mode, or if an alternate selection has been made. 5599 415A79-O 9/22/99 9:40 AM Page 60 Reference Display Display CScan Std A B Std B A Scan B A Scan A B Home Scan A Scan B PREF'D SIDS System Type Selection C Scan Appears if programmed by your carrier. This is the default setting. Standard Mode Your phone first seeks a home type system, then a non-home type. If home system is non-wireline (type A) If home system is wireline (type B) Invert Preference Mode Your phone first seeks a non-home type system, then home type. (Select this mode if in a fringe area of your home system or in certain roaming situations.) If home system is non-wireline (type A) Fast flashing Roam = call on B system Slow flashing Roam = call on home type system Slow flashing In Use = call on home system If home system is wireline (type B) Fast flashing Roam = call on A system Slow flashing Roam = call on home type system Slow flashing In Use = call on home system Home Only Mode Phone will not operate outside its home system. Scan A Mode Phone will operate only within non-wireline (A) systems. Scan B Mode will operate only within wireline (B) systems. Preferred SID's Mode Unit will operate only within specifically identified systems. This choice requires entry of up to 15 System ID numbers for those systems over which you wish to operate. The SID digits are entered as obtained from your Cellular Service Operator. Reference C Scan Your Motorola cellular telephone has been equipped with a special level of A/B System Selection called C Scan. This feature will limit the systems on which you can inadvertently operate and thus minimize billing problems. If you review the roam characteristics of your phone with the R , * sequence, C SCAn will be the first choice which appears in the display if you have at least one negative System I.D. entered. Repeatedly pressing # or * will scroll through the other five System Selection choices as shown above. You may press s to select an alternate choice when it appears in the display. Your choice will remain in effect until you turn off your telephone. On every power-up cycle, the telephone will automatically revert back to C Scan mode of operation. When the NNoo SSvvcc indicator blinks, it indicates either that you are in an area that cannot give you service due to the C Scan mode or an area where no cellular service is available. In this case, you may select another level of A/B "System Selection"

as described on page 60. 6600 6611 415A79-O 9/22/99 9:40 AM Page 62 Reference Preferred SIDs To enter Preferred SIDs:

1. Press R, *. 2. Press * or # to scroll to prefd sids 3. Press s to enter rst 5 digit System ID

(40000 will display as the default). 4. Press # to enter each SID until all desired SIDs are entered (up to 15). 5. Press s to store your entries. Reference Troubleshooting 1. Is the unit locked?

See "Electronic Lock", page 49. 2. Is the No Svc (No Service) indicator lit?

See "Status Indicators", page 16. 3. Is your Roam Indicator lit?

Constant flashing of the RRooaamm indicator while in your home service area may indicate that an incompatible system type has been selected. See "Roaming", page 58. 4. Are you having difculty accessing devices such as answering machines which require longer access tones?

Check to see if Silent Scratchpad is enabled. If so, disable through the Feature Menu, as described in "Select/Cancel Menu Features" on page 39, and try the call again. 6622 63 415A79-O 9/22/99 9:40 AM Page 64 Reference Quick Reference Feature Guide Basic Operation Turn It On P. Lock F, 5. Unlock Three-digit unlock code. Turn It Off P. Place a Call Enter number, S. Receive a Call S, or lift handset to ear. End Call E, or return handset to its mount. Volume Control Earpiece Lift handset, G or H. Speaker With handset mounted, press and hold G or H. Ringer F, then G or H. Store to Memory Number and Phone number, s, Name two-digit location, alpha characters, s. To store in next available location, s, *. Memory Recall By Location R, two-digit location. S to place call. Super Speed Memory location, S. Dialing Turbo Dialing Press and hold memory location (1-9) for one second. Reference Feature Menu Enter Menu F, 1. H or G to scroll. Select Feature C. Cancel Feature C. Exit E. Additional Features Status Review F, 0, 9, R. H or G to scroll. Last Number R, S. Recall Display Own R, #. Number Activate Other R, #, s. Number Mute Microphone F, 6. Scratch Pad Enter numbers during call. E to terminate call and S to place call to scratch pad number. 6644 6655 415A79-O 9/22/99 9:40 AM Page 66 Reference Message Glossary

(Apostrophe) Scrolling activated

* displayed as A Two-System Operation (Active system is non-wireline, using phone number 1.) Two-System Operation (Active system is non-wireline, using phone number 2.) Alpha Entry is selected. Theft Alarm selected. Automatic Answer is active. Automatic Answer is disabled. Automatic Lock is active. Automatic Lock is disabled. Battery Voltage Meter (Number of bars indicates relative level of voltage.) Two System Operation (Active system is wireline, using phone number 1.) Two System Operation (Active system is wireline, using phone number 2.) Master Clear functioning Precedes Cumulative Timer display

(also used to display #) System type selected A A1 A2 ALPHA ARMED AUTO ANSR ON AUTO ANSROFF AUTO LOCK ON AUTO LOCKOFF B==

B1 B2 BUSY C C Scan 6666 CALL CHANGE?

Clear?

EMERGCY EMERGCY CALL On EMERGCY CALLOFF EMPTY EXTEND TALK ON EXTEND TALKOFF FULL HF AUTO NOSWTCH HF AUTO SWTCH HF-

HOME INDIV TIMR ON INDIV TIMROFF Reference Shows incoming call (also used to indicate call in absence) Used when memory protect is activated to prevent accidental overwriting of a memory location Memory Protect is activated to prevent accidental overwriting of a memory location. Emergency Dialing is initiated. Emergency Call is active. Emergency Call is disabled. Name Directory is empty. Extended Talk Time is active. Extended Talk Time is disabled. Indicates all directory locations are full, requested block is unavailable, or location has a number already stored in it Automatic Hands Free is selected. Automatic Hands/free is disabled. Enhanced Simplex Hands Free is selected. System Type Selection Home Mode Individual Timer is active. Individual Timer is disabled. 6677 415A79-O 9/22/99 9:40 AM Page 68 Reference KEYPAD TONE ON KEYPAD TONEOFF LEVEL 1 LEVEL 2 LEVEL 3 LEVEL 4 LEVEL 5 LEVEL 6 LOC Keypad Tones are active. Keypad Tones are disabled. Service level selected Service level selected Service level selected Service level selected Service level selected Service level selected Precedes unlock code when displayed Unit is locked. Multiple Key Answer is active. Multiple Key Answer is disabled. Microphone is muted. Name Preference is activated. Name Preference is disabled. Telephone is on. One Minute Timer is active. One Minute Timer is disabled. LOCKED MULTKEY ANSR ON MULTKEY ANSROFF MUTE NAME PREF ON NAME PREFOFF ON ONE MIN TIMR ON ONE MIN TIMROFF PIN ACTIVE PIN is active. PIN INACTIV R PIN is disabled. Precedes display of Resettable Timer Automatic Redial is selected. REDIAL 6688 Reference Remind Message is active. REMIND MSG ON REMIND MSGOFF RINGER OFF Ring Alert is canceled. RINGER STYLE S==

Remind Message is disabled. Ringer Style is selected. Signal Strength Meter (SSM)

(Number of bars indicates relative signal strength.) System Type Selection (scan non-

wireline A only) System Type Selection (scan A type first, then B) System Type Selection (scan wireline B only) System Type Selection (scan B type first, then A) Signal Strength Meter is active. Signal Strength Meter is disabled. All user features set to standard System Type Selection (non-

wireline standard mode) System Type Selection (wireline standard mode) SCAN A SCAN AB SCAN B SCAN BA SIGNAL MTR ON SIGNAL MTROFF STD STD AB STD BA System Busy Cellular system is busy. SCRPAD TONE ON SCRPAD TONEOFF Scratch Pad Tones are active. Scratch Pad Tones are disabled. 6699 415A79-O 9/22/99 9:40 AM Page 70 Reference THEFT ALARM ON THEFT ALARMOFF TIMER TURBO DIAL ON TURBO DIALOFF V==

Theft Alarm is active. Theft Alarm is disabled. Automatic Display Timer is selected. Turbo Dialing is activated. Turbo Dialing is disabled. Volume Meter (Number of bars indicates relative volume level.) Reference 7700 7711 415A79-O 9/22/99 9:40 AM Page 72 Reference Index Automatic Answer ................................................42 Automatic Hands Free .........................................21 Automatic Lock ....................................................50 Automatic Redial..................................................18 Auxiliary Alert .......................................................52 Battery Indicator...................................................40 Call in Absence Indicator.....................................19 Cancel Menu Features ........................................39 Change Service Level..........................................53 Change Unlock Code...........................................50 Clear Memory Entries ..........................................38 Cumulative Call Timer .........................................48 Display Own Phone Number ...............................24 Display Unlock Code ...........................................50 Distinctive Ringer .................................................44 Earpiece Volume .................................................23 Edit Memory Location ..........................................37 Electronic Lock ....................................................49 End a Call ............................................................19 Enhanced Simplex Hands Free...........................21 Extended Talk Time.............................................41 Feature Status Review ........................................40 General Safety Information...............................6-10 Hands Free Operation (with optional HF Microphone) .....................................20 Incoming Call Screening......................................43 Individual Call Timer ............................................47 Individual Display Timer.......................................47 Introduction ..........................................................11 Last Number Recall .............................................30 Manual Handset to Hands Free Operation..........20 Master Clear ........................................................56 7722 Reference Master Reset .......................................................54 Memory Autoload.................................................27 Memory Linking ...................................................35 Memory Protect ...................................................29 Message Glossary ...............................................66 Microphone Muting ..............................................41 Multiple Key Answer ............................................42 Name Preference.................................................41 One Minute Timer ................................................49 One-Touch Dialing Keys......................................32 One-Touch Emergency Dialing............................33 Pause Dialing.......................................................35 Phone Overview ..................................................12 PIN Code Activation.............................................46 Place a Call..........................................................17 Place a Hands Free Call......................................20 Preferred SIDs ....................................................62 Quick Reference Feature Guide..........................64 Recalling by Location Number.............................29 Recalling from Memory........................................29 Recalling Last 10 Numbers Dialed ......................30 Receive a Call......................................................19 Receive a Hands Free Call..................................20 Resettable Call Timer ..........................................47 Ringer Volume .....................................................24 Roaming...............................................................58 Scratch Pad Memory ...........................................33 Scrolling by Location Number..............................29 Scrolling from Memory.........................................29 Security Features.................................................49 Select Menu Features..........................................39 Selectable System Registration...........................58 Selecting a Memory Location ..............................26 Service Area ........................................................57 7733 Reference Notes 415A79-O 9/22/99 9:40 AM Page 74 Reference Signal Strength Meter....................................22, 39 Silent Keypad.......................................................45 Silent Ringer ........................................................43 Silent Scratch Pad ...............................................45 Speaker Volume ..................................................23 Store to a Location Number.................................26 Storing a Phone Number and a Name ................27 Storing Information in Memory ............................26 Super Speed Dialing............................................31 Switch to Second Phone Number........................24 Switchhook and Enhanced System Services ......58 The Cellular System ............................................57 Theft Alarm ..........................................................51 Timers ..................................................................47 Tone Dialing.........................................................34 Troubleshooting ...................................................63 Turbo Dial ............................................................31 Turn Phone On and Off .......................................15 Two-Part Calling ..................................................34 Volume Meter ......................................................22 Weak Signal Alert ................................................57 Welcome ................................................................4 7744 7755 415A79-O 9/22/99 9:40 AM Page 76 Reference Notes 7766 415A79-O 9/22/99 9:40 AM Page 78 This product may be powered by a rechargeable battery which must be recycled or disposed of properly. Refer to the battery label for battery type. Recycling facilities may not be available in all areas. For additional information regarding disposal or recycling, call 1-800-331-6456 (in U.S.A.). Personal Communication Sector 600 North U.S. Highway 45 Libertyville, Illinois 60048 1-800-331-6456 (in U.S.A.) 1-800-461-4575 (in Canada) www.mot.com 68P09415A79-O 9/98 - SGS registered trademarks of Motorola, Inc.

, and Turbo Dial are 1998 Motorola, Inc. Printed in U.S.A.

APPLICANT: MOTOROLA, INC. FCC ID: IHDT5ZX1 FCC IDENTIFICATION (NAMEPLATE) INFORMATION MOTOROLA INC. FCC ID: IHDT5ZX1 The FCC label shown is the label that will appear on the radio when in production. It will be placed on the outside of the radiotelephone. (Refer to exhibit 3). EXHIBIT 1

APPLICANT: MOTOROLA, INC. FCC ID: IHDT5ZX1 TRANSCEIVER ADJUSTMENTS/TUNE-UP PROCEDURE There are no user accessible adjustments or tuning in this mobile cellular transceiver. All necessary adjustments and tuning are performed during manufacture of the product. Any adjustments or tuning after service or repair are done as part of that process as special equipment is required to perform such adjustments. EXHIBIT 10

APPLICANT: MOTOROLA FCC ID: IHDT5ZX1 October 20, 1999 Gentlemen:

Application:

Confidentiality:

CONFIDENTIALITY REQUEST CONTAINED WITHIN Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Re: Application for Cellular Transceiver Certification Motorola, Inc., Personal Communications Sector, 600 N. U.S. Highway 45, Libertyville, Illinois 60048-1286 herein submits: Application for Equipment Authorization (FCC Form 731-October 1992 with integrated Fee Processing Form, Fee Codes EFT and EBC), application fee in the amount of

$610, and Exhibits; for Type Acceptance of a Cellular Transceiver, FCC ID: IHDT5ZX1. Motorola is also the manufacturer of this equipment. Pursuant to Section 0.459 of the Commission's rules (CFR 47), Motorola requests confidentiality for portions of the material contained in this application and that the identified material be withheld from public inspection following the grant of this authorization. This material contains Motorola's trade secrets and confidential information that Motorola does not customarily release to the public and which is otherwise not generally available to the public. Confidentiality is requested for the following exhibits:

Exhibit 4 Block Diagrams Exhibit 5 Schematics Exhibit 12 Operational Description Description:

Contact Information:

This equipment is a mobile device with the capability to operate in the conventional wide and narrow band Analog Cellular standard in the 800 MHz cellular band. Technical details for this cellular technology are detailed in Exhibit 12. Please contact me by telephone at (847) 523-6167, by facsimile at (847) 523-2350, or by e-mail

(A.Bachler@motorola.com), if there are any further questions or additional information needed concerning this filing. Regards, Andrew J. Bachler FCC Liaison Cellular Subscriber Sector 600 N. U.S. Highway 45 Libertyville, IL 60048-5343 Exhibit 13

APPLICANT: MOTOROLA, INC. FCC ID: IHDT5ZX1 STATEMENT OF CERTIFICATION The technical data supplied with this application, having been taken under my supervision is hereby duly certified. The following is a statement of my qualifications:

Engineering Diploma (MSEE) 1982 Polytechnic Institute of Timisoara, Romania 9 years experience in Computer equipment design 2 years experience in Cellular radiotelephone design SIGNATURE:

NAME: Valeriu Boncu DATE: September 30, 1999 POSITION: Electrical Engineer I hereby certify that the above application was prepared under my direction and that to the best of my knowledge and belief, the facts set forth in the application and accompanying technical data are true and correct. SIGNATURE:

NAME: Nick Grivas DATE: September 30, 1999 POSITION: Engineering Section Manager EXHIBIT 2A APPLICANT: MOTOROLA, INC. FCC ID: IHDT5ZX1 September 30, 1999 Engineer-in Charge Equipment Authorization Branch Federal Communications Commission We hereby certify that this transmit and receive equipment (FCC ID: IHDT5ZY1) for mobile station cellular system use is in full compliance with all parts of Section 2 of TIA/EIA-IS-88 "Mobile Station-Land Station Compatibility Standard for Dual Mode Narrowband Analog Cellular Technology," dated January 1993, which incorporates EIA/TIA-553 "Mobile Station-Land Station Compatibility Specification" and with OET Bulletin No. 53 "Cellular System Mobile Station-Land Station Compatibility Specification."

NAME:

POSITION: Electrical Engineer Valeriu Boncu Telematics Network Access Devices SIGNATURE:

SIGNATURE:

NAME:

POSITION: Engineering Section Manager Nick Grivas Telematics Network Access Devices EXHIBIT 2B

APPLICANT: MOTOROLA, INC. FCC ID: IHDT5ZX1 A draft copy of the installation manual follows. Note: RF exposure information is provided on page 33. EXHIBIT 8c Cellular Mobile and Attache Accessory Installation Manual Installation Manual Attache Accessory...............................................................1 Introduction ........................................................................1 Attache Models ..................................................................2 Attache Assembly ..............................................................3 Assembly Procedure .....................................................3 Secure the Unit .............................................................9 Disassembly ..................................................................9 Carry Phone Accessory.....................................................11 Introduction ......................................................................11 Carry Phone Models........................................................12 Carry Phone Assembly....................................................13 Assembly Procedure ...................................................13 Secure the Unit ...........................................................18 Disassembly ................................................................19 Basic Operation..................................................................20 Power the Unit .................................................................20 Turn Off the Unit ..............................................................20 Release the Handset .......................................................21 Antenna Position..............................................................21 Optional Features...............................................................22 Digital Hands-Free Operation ..........................................22 Battery Option..................................................................23 Mobile Installation ..............................................................27 Planning and Installation..................................................27 Transceiver Location....................................................27 Standard Transceiver Mounting Bracket Installation ...27 Handset Location ........................................................28 Control Unit Mounting Cup Installation .......................30 Adjustable Angle Mounting Bracket Installation (optional) ......................30 Antenna Location ........................................................32 Antenna Installation.....................................................33 Hands-Free Microphone Installation ...........................33 Optional External Speaker Installation........................34 Control/Power Cable Routing ......................................35 Control/Power Cable Installation .................................36 Performance Checks........................................................39 Checking Performance ................................................39 Checking Auxiliary Alert Feature.................................40 Before Calling for Service .................................................42 General Safety Information ...............................................44 Rules, Regulations, and Precautions ...............................50

, and Motorola are trademarks of Motorola, Inc. TOC Installation Manual Attache Accessory NOTE Not all Motorola models are available for purchase as Attaches. Check with your cellular dealer for information regarding the purchase of the Attache accessory to convert your mobile into an Attache. Introduction This section of your manual describes the assembly and installation of the Motorola Attache. The Motorola Attache is a lightweight, three-watt unit that is powered by your vehicles electrical system through the cigarette lighter socket. This phone is completely self-contained, and may be moved easily between your personal car(s), a company truck or car, or a rental car because it requires no complex wiring installation within the vehicle. The unit is installed in the vehicle by simply securing it to a spare seat with a lap belt and plugging it into the vehicles cigarette lighter socket. For further information about the features and capabilities of your cellular telephone, see the accompanying user manual. 1 Installation Manual Bag Battery Battery Adapter Hands-Free Microphone

(optional) Antenna Handset Transceiver Battery Charger Power Connector with Cigarette Adapter Figure 1 Attache Models Two Attache models are offered. The standard version is powered by your vehicles electrical system and does not come equipped with a battery. The power connector assembly contains connectors for an optional battery and an external hands-free microphone, if so desired. The deluxe version comes complete with a battery, an AC charger, and an integrated hands-free microphone contained in the connector assembly. An external full-

duplex hands-free microphone can be purchased separately. The hands-free feature allows you to place or answer calls without removing your hands from the steering wheel (except to enter the number to be called). See 2 Installation Manual Digital Hands-Free Operation in the User Manual for more information about hands-free calling. Attache Assembly The items included with your Motorola Attache are shown in Figure 1. The following procedure will guide you through the assembly of your Attache. Assembly Procedure Step 1 Remove the transceiver from its Attache compartment. Step 2 Carefully connect the 25-pin connector of the power connector assembly to the front of the transceiver and tighten the two thumbscrews as shown in Figure 2. Figure 2 3 Installation Manual Step 3 Locate the antenna and screw it tightly onto the connector as shown in Figure 3. Figure 3 If your Attache is equipped with a battery, proceed to step 5. Step 4 Carefully place the transceiver, antenna, and connector assembly into the transceiver pocket as shown in Figure 4a, and zip the pocket closed, leaving the antenna outside of the pocket as shown in Figure 4b. Be sure to connect the cigarette lighter plug to the cigarette lighter socket on your vehicle dashboard when you are ready to use your phone. 4 Installation Manual Figure 4a Figure 4b 5 Installation Manual Steps 5 and 6 should be followed if your Attache is equipped with a battery. Step 5 Locate the battery adapter cable and snap the battery connector clip onto the battery as shown in Figure 5a. Attach the other end to the battery connector assembly as shown in Figure 5b. Figure 5a Figure 5b 6 Installation Manual Step 6 Carefully place the transceiver/battery assembly into the transceiver pocket as shown in Figure 6, and zip closed. Figure 6 Step 7 Plug the handset modular connector into the jack located on the side of the transceiver as shown in Figure 7, and place the handset into the hang-up cup. Figure 7 7 Installation Manual Step 8 Finally, use your pocket system for business planning tools such as calendars, notepads, business cards, etc. as shown in Figure 8. NOTE These items are purchased separately. NOTE Be sure to charge the battery for at least 10 hours, or overnight, using the AC charger before attempting to use the cellular telephone. Figure 8 8 Installation Manual Secure the Unit To secure the unit in your vehicle, run a standard lap belt through the loop located on the outside of the carry case as shown in Figure 9. Figure 9 Disassembly If you wish to remove the handset and transceiver from the Attache accessory for servicing, or to place them in a vehicle equipped with a permanent mobile installation, use the following procedure. Step 1 Turn the unit off by pressing on the handset. Step 2 Unplug the handset from the modular connector jack on the side of the transceiver and remove it from the hang-up cup. Step 3 Unzip the transceiver compartment and carefully lift the transceiver/connector assembly out of the pocket. Step 4 Unscrew and remove the antenna. 9 Installation Manual Step 5 Unscrew the two thumbscrews on the front of the power connector and remove the power connector assembly from the transceiver by gently pulling it away from the transceiver front plate. Step 6 Return the antenna and power connector assembly into the carrying case for safe keeping. Reverse the above procedure to re-assemble. See page 20 for Basic Operation. 10 Installation Manual Carry Phone Accessory NOTE Not all Motorola models are available for purchase as carry phones. Check with your cellular dealer for information regarding the purchase of the carry phone accessory to convert your mobile into a carry phone. Introduction This section of your manual describes the assembly and installation of the Motorola cellular carry phone. The Motorola cellular carry phone is a lightweight, three-watt unit that is powered by your vehicles electrical system through the cigarette lighter socket. This phone is completely self-contained, and may be moved easily between your personal car(s), a company truck or car, or a rental car because it requires no complex wiring installation within the vehicle. The unit is installed in the vehicle by simply securing it to a spare seat with a lap belt and plugging it into the vehicles cigarette lighter socket. For further information about the features and capabilities of your cellular telephone, see the accompanying user manual. 11 Installation Manual Bag Battery Battery Adapter Sleeve Antenna Handset Battery Charger Transceiver Power Connector with Cigarette Adapter Hands-Free Microphone

(optional) Figure 10 Carry Phone Models Two carry phone models are offered. The standard version is powered by your vehicles electrical system and does not come equipped with a battery. The power connector assembly contains connectors for an optional battery and an external hands-free microphone, if so desired. The deluxe version comes complete with a battery, an AC charger, and an integrated hands-free microphone contained in the connector assembly. An external full-duplex hands-free microphone can be purchased separately. The hands-free feature allows you to place or answer calls without removing your hands from the steering wheel (except to enter the number to be called). See Digital Hands-Free Operation on page 22 for more information about hands-free calling. 12 Installation Manual Carry Phone Assembly The items included with your Motorola cellular carry phone are shown in Figure 10. The following procedure will guide you through the assembly of your carry phone. Assembly Procedure Step 1 Remove all components from the bag. Step 2 Carefully connect the 25-pin connector of the power connector assembly to the front of the transceiver and tighten the two thumbscrews as shown in Figure 11. Figure 11 Step 3 Locate the antenna and screw it tightly onto the connector as shown in Figure 12. Figure 12 13 Installation Manual Step 4 Take the vinyl sleeve and slide the transceiver assembly into the sleeve, wrapping the Velcro tab over the power connector. Be sure the telephone jack located on the side of the transceiver lines up with the opening in the sleeve. See Figure 13. Figure 13 Step 5 Place the handset in the hang-up cup and plug the handset modular connector into the jack located on the side of the transceiver. See Figure 14. Figure 14 14 Installation Manual Step 6 Place the transceiver assembly into the bag allowing enough room for clearance of the handset coil cord. See Figures 15a and 15b. Note that the antenna folds conveniently down into the bag to prevent possible damage. NOTE Be sure to connect the cigarette lighter plug to the cigarette lighter socket on your vehicle dashboard when you are ready to use your phone. Figure 15a Figure 15b Steps 7 and 8 should be followed if your carry phone is equipped with a battery. 15 Installation Manual Step 7 Locate the battery adapter cable and attach the modular end to the battery connector assembly as shown below. Figure 16 Feed the cable through the opening to the battery compartment in the lower corner of the bag. Place the battery into the battery compartment and snap the battery connector clip onto the battery as shown in Figure 17. Figure 17 16 Installation Manual Step 8 Zip the battery compartment closed. See Figure 18. Figure 18 Step 9 The battery should now be charged for at least 10 hours or overnight using the AC charger before attempting to use the cellular telephone. Please note that there is an opening in the lower left corner of the bag to allow for connection of an external antenna. The transceiver unit can positioned in either direction when placed in the bag. See Figures 19a and 19b. Figure 19a 17 Installation Manual Figure 19b Secure the Unit To secure the unit in your vehicle, run a standard lap belt through the loop located on the outside of the carry case as shown in Figure 20. Figure 20 18 Installation Manual Disassembly If you wish to remove the handset and transceiver from the carry phone accessory for servicing, or to place them in a vehicle equipped with a permanent mobile installation, use the following procedure. Step 1 Turn the unit off by pressing on the handset. Step 2 Unplug the handset from the modular connector jack on the side of the transceiver and remove it from the hang-up cup. Step 3 Lift the transceiver assembly out of the carry bag using the loop handle. Unwrap the Velcro tab and slide the transceiver out of the Velcro sleeve. Step 4 Unscrew and remove the antenna. Step 5 Unscrew the two thumbscrews on the front of the power connector and remove the power connector assembly from the transceiver by gently pulling it away from the transceiver front plate. Step 6 Return the antenna and power connector assembly into the carrying case for safe keeping. Reverse the above procedure to re-assemble. 19 Installation Manual Basic Operation Power the Unit This unit is designed to operate in two different modes. The rst operating mode is standard mode, and the second is battery saving mode. If your Attache/Carry phone is not equipped with a battery, it will always operate in the standard mode. Standard Mode When you plug your unit into the vehicle cigarette lighter socket and press on the handset, the unit will sense the voltage present at the cigarette lighter socket and automatically behave exactly as it would in a standard mobile installation. The handset backlighting will remain lit, and the handset display will stay on as long as the telephone remains on. Battery Saving Mode When you press on the handset, and the cigarette lighter plug is not plugged in (or there is no voltage present at the cigarette lighter socket) your Attache/Carry phone will automatically shut off the handset backlighting and blank the display after six seconds. Pressing any key will turn the display and backlighting back on for another six seconds. Turn Off the Unit Your Attache/Carry phone should always be turned off using on the handset. NOTE If the handset is unplugged from the transceiver prior to turning off the unit with the handset ,the unit will continue to drain its (or your 20 Installation Manual vehicles) battery. It is very important to turn off the unit using on the handset. Release the Handset Lift up and remove the handset, as shown in Figure 21. To Hang Up Engage Notch in Top of Handset Against Target Button. 2 Target 1 Pivot Unit and Remove. 3 Pivot Unit Until Latched. Hang-Up Cup Figure 21 Antenna Position If your Attache/Carry phone is equipped with a folding antenna, the antenna may be folded downward for convenient storage when the Attache/Carry phone is not in use. However, for best performance when using the Attache/Carry phone, you should always place the antenna in the full upright position. Also, when using the Attache/Carry phone, remember to keep the cigarette lighter cord, handset coil cord, and optional hands-free microphone cord as far away from the antenna as possible. 21 Installation Manual Optional Features Digital Hands-Free Operation Your Attache/Carry phone may be equipped with a hands-free wireless microphone integrated into the connector attached to the transceiver. This is a safety feature which offers the convenience of hands-free conversation without the use of an external microphone. For optimum hands-free sound quality while using the integrated microphone, Enhanced Simplex Hands-Free operation should be enabled through the menu. See page 15 in the User Manual for further details. For enhanced hands-free sound quality, an external microphone can be purchased as an accessory and is typically positioned on your sun visor. Full Duplex Hands-Free provides improved audio quality relative to Enhanced Simplex Hands-Free and makes it easier to enter the conversation while the other party is talking. Detailed instructions for placing and receiving hands-free calls are in your Cellular Telephone User Manual. Battery Option Description You may purchase a battery option for your Attache/Carry phone which allows you to operate the Attache/Carry phone away from the vehicle. In the Attache model, the battery mounts on top of the 22 Installation Manual transceiver inside the carrying case. In the Carry model, the battery mounts in the battery compartment located outside the carry case. Under normal operating conditions, a fully charged unit will provide 70 minutes of continuous talk time before requiring recharging. The actual time between charges will depend on many factors, such as the age of the battery, how often it is recharged, the length and frequency of phone calls, and the air temperature. Charging the Battery The battery in your Attache/Carry phone can be charged using the cigarette lighter receptacle in your vehicle or the AC charger included with the unit. When charging the Attache/Carry phone using the vehicle cigarette lighter receptacle, the battery will charge at various rates depending upon whether the telephone is on, whether it is being used to place a call, your vehicles engine speed, and the number of accessories (e.g., air conditioning, blower, window defrosters, etc.) that are in operation in your vehicle. The best circumstances for charging your battery are when your vehicle is operating at highway speed, there are few accessories in operation, and the telephone is either off, or on but not in a call. Under these circumstances, the battery will fully charge in about 3 hours. In other circumstances, your vehicle will provide a trickle charge to your battery, so you can use the Attache/Carry phone in your vehicle while its battery is recharging, but the recharging time will be extended. 23 Installation Manual It should be noted that the Attache/Carry phone will operate in a vehicle, using the cigarette lighter receptacle, even if the Attache/Carry phone battery is completely discharged. The AC charger will fully charge your Attache/Carry phone battery in about 10 hours. There is also an optional rapid charger available that will charge your Attache/Carry phone battery in 3 hours. The Attache/Carry phone can be used while it is connected to the AC charger, provided that the battery is at least partially charged. When connected to the AC charger, if the battery is completely discharged, the battery should be partially recharged before you attempt to use the Attache/Carry phone. Battery Care The useful lifetime of a rechargeable battery is affected by how it is used and how often it is recharged. The Attache/Carry phone battery is a sealed lead acid battery that is somewhat similar to the battery used in your car. Unlike some other types of batteries, your Attache/Carry phone battery is not subject to the memory affect associated with frequent charging. In fact, it is best to charge your battery as often as possible. Your batterys lifetime will also be extended if you avoid fully discharging the battery. It is also important to remember to always store, operate, and charge your battery in a well ventilated area. This battery should NEVER be placed in an airtight container. Also, to avoid damaging the battery, NEVER allow a paper clip, or other metal object to 24 Installation Manual rest across the terminals of the battery. In addition, DO NOT puncture the battery, or dispose of it in a re. Using Spare Batteries You may remove the battery and replace it with a charged spare battery. See your cellular telephone sales representative to purchase spare batteries. WARNING Do not use a nickel cadmium battery with this product. It is not compatible with the charging method, and may burst. Field Installation of the Battery Option for Attache Phone Model If your unit was purchased without the battery option, a battery conversion kit may be purchased and installed. This kit consists of a battery, battery charger, and a battery clip connector. The installation should be performed according to the instructions below. Step 1 Turn the unit off by pressing on the handset. Step 2 Disconnect the handset modular connector from the jack located on the side of the transceiver. Step 3 Unzip the transceiver compartment and carefully remove the transceiver and power connector assembly. Step 4 Follow steps 5 7 of the assembly procedure, beginning on page 2. 25 Installation Manual Field Installation of the Battery Option for Carry Phone Model If your unit was purchased without the battery option, a battery conversion kit may be purchased and installed. This kit consists of a battery, battery charger, and a battery clip connector. The installation should be performed by following Steps 7-8 of the assembly procedure beginning on page 7. 26 Installation Manual Mobile Installation Planning and Installation Transceiver Location In many vehicles the best location for the transceiver unit is the oor of the trunk compartment; alternate locations are under the dash, under the front or rear seat, and under the rear speaker deck panel. Regardless of the location choice, be sure the transceiver unit is protected from dirt and moisture and that there is sufcient space around the transceiver unit to allow airow and removal. Also, allow for adequate clearances for the control/power cable connector and antenna coaxial cable. Standard Transceiver Mounting Bracket Installation Install the standard mounting bracket as follows:

Horizontal Mounting Step 1 Use the mounting bracket fitted over the transceiver as a template to determine the mounting screws (2) locations. Be sure to first snap the mounting bracket over the transceiver, since the bracket will flex. Also note the mounting bracket only fits one way. Be sure that the selected mounting location allows for adequate airflow for the transceiver. Step 2 Place the mounting bracket on the selected mounting surface. Mark the locations for the two mounting screws. 27 Installation Manual Step 3 Center punch the screws locations. Drill 1/8 inch holes for the mounting screws. WARNING Be careful to avoid drilling into the fuel tank or other vital part of the vehicle. Step 4 With the transceiver in place under the mounting bracket, secure the bracket to the mounting surface using the self-tapping screws and lock washers provided in the fuse kit. Vertical Mounting Follow the same procedures for horizontal mounting except for the two mounting screws. In place of the mounting screws, use two suitable size bolts, nuts, and washers (installer supplied). Place a lock washer between each bolt and the mounting bracket, insert the bolts through the bracket and holes drilled in mounting surface, and secure with flat washers and nuts. Handset Location Consider the following factors when deciding the handset mounting location:

The mounting surface must have sufcient strength to support the handset. The handset must be within easy reach of the driver during normal operation of the vehicle and should not interfere with the drivers or passengers seating or leg space. The handset must also be within reach of the handset end of the control/power cable. 28 Installation Manual 8-18 x 1"

Mounting Screws Antenna Connector Mounting Bracket Transceiver Mounting Surface Figure 22 29 Installation Manual Control Unit Mounting Cup Installation The control unit mounting cup is used to hold the control unit handset. Machine Screws (4) M4 x 0.7 x 10 Rubber Tip Bumper (2) Upper Shell Figure 23 Adjustable Angle Mounting Bracket Installation (optional) The adjustable angle mounting bracket provides a convenient means for mounting the control unit. In a typical application, the control unit hang-up cup mounts directly to the adjustable angle mounting bracket. Install the adjustable angle mounting bracket as follows:

Step 1 Temporarily position the control unit and mounting bracket to verify the desired mounting location. Check for clearance and 30 Installation Manual operating convenience. Using the surface base as a guide, mark four holes on the transmission hump or other selected location. The four mounting tabs on the surface base are somewhat flexible to conform to a curved surface as necessary. Step 2 Using an awl or similar device, open four holes in the carpet at marked locations. This must be done prior to drilling to avoid ruining the carpet. Step 3 Using a 3.2 mm (1/8") bit, drill the four mounting holes and secure the surface base using the four 8-1/8 x 3/4" tapping screws provided. Step 4 Mount the base to the surface base at the desired angle and securely tighten the angle-

adjusting screws. 31 Installation Manual Lock Washer (4) INT tooth

#8 Hex Nut (4) M4 x 0.7 Angle-Adjusting Screws (2)

(One on each side) Base 0

-110 Adjustable Angle Surface Base 8-1/8 x 3/4"

Tapping screws (4) Metal Strip with Hole

(Four strips are provided to facilitate mounting of bracket on contoured surfaces) Figure 24 Antenna Location The best location for the antenna is at the center of the vehicle roof, or on glass near the roof. Motorola offers (as an option) a thru-the-glass type antenna which should be mounted on the vehicle rear window. This type of antenna should be positioned as high on the window as possible. The inductive button on the mounting foot must not be crossed by a rear window defogger element. 32 Installation Manual Antenna Installation IMPORTANT: To meet the FCCs RF Exposure Guidelines, the antenna should be installed to ensure a minimum distance between the body of the user and nearby persons and the antenna. To determine the minimum distance, calculate the combined cable loss and antenna gain and refer to the graph below to identify the required minimum separation distance in centimeters. Combined Cable Loss and Antenna Gain vs. Minimum Separation Distance Combined Cable Loss and Antenna Gain vs. Minimum Separation Distance

) B d

i

) i n B a d

G n a a G n n a n e e t t n n A A d d n n a a s s s o s L o e L b a e C b d a e C n b d m e o n C b m o C i l i l 5 4 3 2 1 0

-1

-2

-3

-4 20 25 30 35 40 45 50 Minimum Separation Distance (cm) Minimum Separation Distance (cm) Hands-Free Microphone Installation The mounting position of the Digital HF hands-free microphone within the vehicle has a denite inuence on the performance of the Vehicular Speaker Phone

(V.S.P.) hands-free operation. The microphone should be mounted either on the sun visor (directly above the driver) or on the headliner (above the driver). The microphone should never be mounted near the window or in a location where the road and ambient background noise would be substantially high (above 85 dB SPL). 33 Installation Manual The visor clip mounting bracket provides the simplest and most effective mounting of the hands-free microphone. See Figure 25. The clip slides into channels on the microphone housing, and then clips on to the sun visor. The cable may then be unobtrusively routed to the Digital HF microphone jack located near the power cable connector on the DHFA. Sun Visor Sun Visor Mounting Clip Microphone Cable Hands-Free Microphone Figure 25 Optional External Speaker Installation The external speaker should be mounted under the dash, on the transmission hump, or in any other suitable location using the mounting bracket supplied with the speaker assembly. The proposed location must not interfere with the operation of the vehicle. Also, the speaker must be securely attached to its 34 Installation Manual mounting bracket. Every effort should be made to avoid locating the speaker behind a sound absorptive barrier (e.g., facing upward under the seat or behind a dashboard panel). CAUTION Do not install either the speaker or DHFA unsupported to prevent shifting of the unit which could interfere with the proper operation of the vehicle. Always use the supplied mounting hardware. Control/Power Cable Routing Many vehicles are equipped with wire troughs in the door sills. If the vehicle has this feature, use it to provide maximum protection for the cables and to simplify installation. In vehicles without wiring troughs, the power cable must be routed where it will be protected from pinching, sharp edges, and crushing. To avoid interference with the vehicles electronics, do not run cables above the catalytic converter or near the vehicles electronic modules. Use grommets whenever a cable must pass through a hole in a metal panel. No matter what method of cable routing is implemented, all in-line connectors must be kept accessible. The mobile telephone system is designed to operate in negative ground 12-volt electrical systems only. To minimize electrical noise that interferes with the cellular telephone operation, be sure to check the condition of the ignition wiring and the connections to the vehicle battery. All wire connections should be clean and tight. 35 Installation Manual Control/Power Cable Installation The control/power cable provides interconnection of the transceiver, handset, microphone (if equipped), and the external speaker (if equipped). See Figure 26 for installation diagram. Install the control/power cable as follows:

Step 1 Route the control/power cable as previously specified. Do not pull on the connector housings while routing the cable. Step 2 Install and route the antenna coaxial cable as previously noted. Connect the coaxial cable to the transceiver and to the antenna. Step 3 Remove all fuses and tape them to their respective holders. Step 4 Bolt the black lead(s) of the power/control cable to a suitable grounded point on the vehicle frame using the ring lug provided. NOTE Special attention should be given to locating a good vehicle ground. Optimum radio performance can only be achieved with a ground connection having a very low resistance. The vehicle frame makes the best ground, but body structural reinforcement members are also suitable for grounding purposes. Verify that the connections between the battery negative terminal, vehicle chassis, and engine block have low resistance. If it becomes necessary to run the black lead to the battery, the lead must be fused with a 10-

amp fuse. 36 Installation Manual Speaker Digital Hands-Free Microphone AUX Alert Yellow/

Black Blue Crimp Connector

(not supplied) To Lights, Horn, etc. 2 Ampere Relay

(500 mA max. coil rating) 10 Ampere Red Blue Crimp Connector Black Chassis Ground Ignition Sense Green/

Black 4 Ampere Ignition Switch Blue Crimp Connector In-Line Splice l e b a C r e w o P Handset Battery Chassis Ground Transceiver Antenna Control Cable Figure 26 Step 5 Connect the D-type connector on the power cable, and the modulator connector on the control cable, to the transceiver. Step 6 Check the power cable fuses and make sure that the correct sizes and types are supplied. Step 7 The green/black ignition sense lead of the power cable should normally be connected to 37 Installation Manual an accessory terminal at the vehicle fuse block, through the green wire of the fuse holder assembly. For proper operation of the convenience on/off feature, the accessory terminal voltage should go to A + with the ignition switch on, then go low while cranking the starter, then return to A + with the vehicle running. If the ignition sense lead is left unter-

minated, the mobile must be turned on with on the handset, and it will always turn on locked. Cut and strip the green wire connected to the fuse holder (to position the fuse in the desired location) and connect one end to a convenient point on the wire coming from the appropriate accessory terminal using the in-

line splice. Connect the other end to the green/black ignition sense lead on the power cable, using the blue crimp-style connector. Step 8 The yellow/black auxiliary alert lead of the power cable provides a ground for the first five times that the mobile unit rings. The ground has a fixed duration of one second for each ring. Although the auxiliary alert line has a 1/2 ampere capacity, it is recommended that the connection to the auxiliary alert device (such as the vehicle horn, headlights, etc.) be made through a suitable relay using a 2A slow-blow fuse for circuit protection. The auxiliary alert feature must be activated by the telephone user prior to turning off the car. Ignition sense must be low in order to use the auxiliary alert feature. If this feature is not desired, the 38 Installation Manual yellow/black lead may be left unterminated. NOTE Local regulations may forbid the use of horns and/or flashing headlights as auxiliary alert devices. Consequently, the auxiliary alert external signaling feature should not be used in these areas. Step 9 Cut and strip the red wire(s) connected to the fuse holder (to position the fuse in the desired location) and connect one end to the positive battery terminal using the lug supplied. Connect the other end to the red A + wire on the power cable, using the blue crimp-style connector. Step 10Connect the external speaker and microphone connectors (if equipped) to the speaker and microphone jacks on the control/power cables.

(It is recommended that the plugs not be installed in an area exposed to excessive moisture.) Step 11 Carefully inspect all cables and connections; then insert the 10A fuse into the fuse holder on the red lead and the 4A fuse into the fuse holder on the green/black lead. Performance Checks Checking Performance Once the mobile telephone has been installed, its performance should be checked using the following procedure. Refer to the User Manual for instructions on how to turn on, unlock, and place calls. 39 Installation Manual Step 1 Place a call from the mobile and confirm proper operation. Use both the handset and the optional hands-free during this call if the phone is so equipped. Step 2 Have a call placed to the mobile and confirm proper operation. Use both the handset and the optional hands-free during this call if the phone is so equipped. Step 3 If you experience difficulty placing and receiving calls, check the voltage standing wave ratio (VSWR) using the following method. Measure the power output of the radio with the radio connected to the vehicle antenna through a directional watt meter. Measure the forward power and reflected power with the watt meter and compute the VSWR as follows:

voltage standing wave ratio =

where R = reflected power forward power 1+R 1- R The VSWR should be less than 2:1. If the VSWR is greater than 2, check the antenna and its cable connector. Checking Auxiliary Alert Feature Step 1 Prepare the unit to receive test calls by enabling the auxiliary alert feature, in accordance with the procedures provided in the User Manual. Place a test call to the mobile. 40 Installation Manual Step 2 Verify the alert device has been activated by the incoming call and then answer the call. Step 3 With the auxiliary alert feature enabled, place a second test call to the mobile. Do not answer the call. Verify that after approximately 20 seconds (5-6 rings), the alert device has been deactivated and that the handset displays CALL after being enabled in the manner described in the User Manual. 41 Installation Manual Before Calling for Service After installation, programming, and performance checkout, your cellular telephone is ready for operation. If you experience operating difculties, check the following before making a call for service:

Have you read your User Manual?

Everything you need to know to operate your cellular telephone is in your User Manual. Take the time to read it and become familiar with all the features of your telephone before calling for service. Note that not all of the features discussed below are included in all telephone models. If your telephone is equipped with digital hands-free

(with an external microphone), do you hear excessive feedback noise during a hands-free call?

Because of audio variations in the cellular system, excessive feedback noise or howling may sometimes be heard when a full duplex (if your telephone is so equipped) hands-free call is placed or received. If this occurs, decrease the speaker volume using the volume control on the handset. Also, verify that the microphone was not installed in an area of the vehicle that is subject to high background noise (above 85 dB SPL). More information about hands-free operation can be found in your User Manual. 42 Installation Manual If your telephone is equipped with the integrated hands-free microphone, do you hear excessive feedback noise during a hands-free call?

Check your User Manual to be sure you have enabled Enhanced Simplex Hands-free Operation. See your User Manual for further details. Have you unlocked your unit?

Your cellular telephone is inoperative when locked. This state is indicated by LOCKED in the display. To unlock the telephone, enter your three-digit unlock code. LOCKED will disappear. Does the red No Svc message continue to display?

This may indicate that you are outside of the service area, or in a marginal reception area. Marginal reception may also be indicated by the fast busy or alternating high-low sound when attempting to place a call. Have you programmed a unique operating mode into the unit?

Constant ashing of the Roam indicator or illumination of the No Svc indicator while in your home service area may indicate an undesired roam characteristic choice has been selected. See Selectable System Registration or Roaming, in the User Manual. 43 Installation Manual General Safety Information Read this information before using your mobile cellular car telephone. The cellular telephone is one of the most exciting and innovative electronic products ever developed. With it you can stay in contact with your ofce, your home, emergency services, and others. For the safe and efcient operation of your phone, observe these guidelines. Your mobile cellular telephone is a radio transmitter and receiver. When the phone is on, the externally mounted antenna is the part of the phone that sends out and receives radio frequency (RF) energy. The phone operates in the frequency range of 824 MHz to 894 MHz and employs commonly used frequency modulation (FM) techniques. When you use your phone, the cellular system handling your call controls the power level at which your phone transmits. The power level can range from 0.005 of a watt to 3 watts. Exposure to Radio Frequency Energy In 1991 the Institute of Electrical and Electronics Engineers (IEEE), and in 1992 the American National Standards Institute (ANSI), adopted the 1982 ANSI Standard for safety levels with respect to human exposure to RF energy. Over 120 scientists, engineers, and physicians from universities, government health agencies, and industry, after reviewing the available body of research, developed this updated Standard. In March, 1993 the Federal Communications Commission (FCC) proposed the 44 Installation Manual adoption of this updated Standard. To operate within this updated ANSI Standard, use your phone as described under Safe and Efcient Phone Operation. Safe and Efcient Phone Operation Do not operate your mobile cellular telephone when a person is within 4 inches (10 centimeters) of the antenna unless that person is shielded from the antenna by a metal surface such as the roof of the car. Otherwise you may impair call quality, may cause your phone to operate at a higher power level than is necessary, and may expose that person to RF energy in excess of that established by the updated ANSI Standard. Antenna Care and Replacement Do not use the phone with a damaged antenna. Replace a damaged antenna immediately. Consult your manual to see if you may change the antenna yourself. If so, use only a manufacturer-approved antenna. Otherwise, have your antenna repaired by a qualied technician. Use only the supplied or approved antenna. Unauthorized antennas, modications or attachments could damage the phone and may violate FCC regulations. 45 Installation Manual Driving Check the laws and regulations on the use of cellular telephones in the areas where you drive. Always obey them. Also, when using your phone while driving, please:

give full attention to driving, use hands-free operation, if available, and pull off the road and park before making or answering a call if driving conditions so require. Vehicle Electronic Equipment RF energy may affect some electronic systems in motor vehicles. Check with your vehicle manufacturers representative to be sure your phone will not affect the electronic systems of your vehicle. Children Do not allow children to play with your phone. It is not a toy. Children could damage the phone, or make calls that increase your telephone bills. Blasting Areas To avoid interfering with blasting operations, turn your unit off when in a blasting area or in areas posted:

turn off two-way radio. Construction crews often use remote control RF devices to set off explosives. Potentially Explosive Atmospheres Turn your phone off when in any area with a potentially explosive atmosphere. It is rare, but your phone or its accessories could generate sparks. Sparks in such areas could cause an explosion or re resulting in bodily injury or even death. 46 Installation Manual Areas with a potentially explosive atmosphere are often, but not always, clearly marked. These areas may include fueling areas such as gas stations; fuel or chemical transfer or storage facilities; and areas where you would normally be advised to turn off your engine. Do not transport or store ammable gas, liquid, or explosives in the compartment of your vehicle which contains your phone or accessories. Vehicles powered by liqueed petroleum gas (such as propane or butane) must comply with National Fire Protection Standard (NFPA-58). For a copy of this standard, contact the National Fire Protection Association, One Batterymarch Park, Quincy, MA 02269, Attn: Publications Sales Division. Other Electronic Equipment Most modern electronic equipment - for example, personal medical devices, equipment in hospitals and cars - is shielded from RF energy. However, RF energy from cellular telephones may affect some electronic equipment. Consult your physician or ask the manufacturer of any personal medical device (such as pacemakers, hearing aids, etc.) to determine if they are adequately shielded from external RF. When using your phone as a carry phone, turn it off in health care facilities when any regulations posted in the areas instruct you to do so. Always request permission before using your carry phone near medical equipment. 47 Installation Manual Aircraft (Carry Phone Conguration Only) Turn your phone off before boarding any aircraft. Use it on the ground only with crew permission. Do not use it in the air. To prevent interference with critical aircraft systems, Federal Aviation Administration (FAA) regulations require you to have permission from a crew member to use your phone while the plane is on the ground. To prevent interference with cellular systems, FCC regulations prohibit using your phone while the plane is in the air. The design of Motorolas cellular telephones complies with all applicable RF Safety Standards. Motorola meets the standards and recommendations for the protection of public exposure to RF electromagnetic energy established by governmental bodies and other qualied organizations, such as the following:

National Council on Radiation Protection and Measurements (NCRP). Report 86. Department of Health and Welfare Canada Safety Code 6. Verband Deutscher Elektroinigenieure (VDE) DIN-

0848. Directives of the European Community, Directorate General V in Matters of Radio Frequency Electromagnetic Energy. National Radiological Protection Board of the United Kingdom GS-11, 1988. American National Standards Institute (ANSI) / IEEE C95.1-1992. 48 Installation Manual Magnetic Storage Media Your phone contains a magnet. Do not place your phone in close proximity to magnetic storage media such as diskettes or credit cards for extended periods of time. Batteries CAUTION To prevent injuries or burns, do not allow metal objects to contact or short circuit the battery terminals. 49 Installation Manual Rules, Regulations, and Precautions The U. S. Federal Communications Commission and the Canadian Department of Communications regulate cellular radiotelephone service in their respective countries. It is important for you, the cellular radiotelephone user, to observe the applicable regulations when operating your cellular phone in either country. In addition to these U.S. and Canadian regulations, you may also be bound by certain state, provincial, territorial, and local rules and regulations, as well as by your cellular carriers tariff (the rates, terms, and conditions of its service). If you wish to use your cellular radiotelephone in both the U.S. and Canada, please consult with your system operator. Furthermore, you should remember that your cellular phone is a radiotelephone, i.e., it combines both wireline technology, as used in your home or ofce telephone system, and radio technology and that the scope of regulations and precautions is therefore broader than the scope of regulations and precautions relating to wireline-only telephone usage. Some of the major points of consideration are set out below. Please note, however, that this Rules, Regulations, and Precautions section does not constitute legal advice; and is intended merely for general information purposes. If you have any specic questions, please contact your Cellular Carrier

(System Operator). 50 Installation Manual License - If your home system is in the U. S., you do not require a separate license to operate your cellular telephone; obtaining a cellular telephone access number is sufcient to register you as a user. If your home system is in Canada, a separate license is required; your carrier will assist you in the licensing process. If you wish to use your cellular phone on both sides of the border, please contact your Cellular Carrier (System Operator). Denial of Service - A cellular carrier may deny service temporarily, or terminate service for violation of any government regulations or of its tariff. Consumer Responsibilities - Remember that the wireline and radio regulations with respect to harassing calls, false distress calls, obscene language, etc. apply to cellular phone usage. Privacy - As a telephone user, you have come to assume a certain standard of privacy when you place or receive a telephone call via the traditional wireline systems. However, because cellular radiotelephones utilize radio transmissions to effect calls, the same standard cannot always be assured. While it is unlawful for an unauthorized person to divulge or use any information obtained from intercepting or listening in on conversations intended for others, you should not assume that your conversation is completely secure. Commercially available scanning equipment can permit a third party to monitor the radio channels used for cellular telephone calls. Interference - No person shall interfere with or cause interference to any radio communication or signal. 51 Installation Manual Equipment Modications - The U.S. Federal Communications Commission has type-approved and the Canadian Department of Communications has granted technical acceptance to the model of cellular telephone which you have purchased, and both have allocated a specic frequency range for cellular service. No changes or adjustments are to be made to your cellular phone. 52 Pan American Cellular Subscriber Group 600 North U.S. Highway 45 Libertyville, Illinois 60048 1-800-331-6456 U.S.A. 1-800-461-4575 Canada 6809383A19-B 01/31/00-RGC Motorola, Inc. 1995 All Rights Reserved Printed in U.S.A.

APPLICANT: MOTOROLA, INC. FCC ID: IHDT5ZX1 A draft copy of the latest users manual follows. Note: RF exposure information is provided on page 7. EXHIBIT 8b Table of Contents Getting Started.....................................................4 Welcome ................................................................4 Safety Information..................................................6 Introduction ..........................................................11 Phone Overview...................................................12 Basic Operation .................................................15 Turn Phone On and Off........................................15 Place a Call..........................................................17 Automatic Redial..................................................18 End a Call ............................................................19 Receive a Call......................................................19 Call in Absence Indicator.....................................19 Signal Strength Meter ..........................................20 Volume Meter.......................................................20 Speaker Volume...................................................21 Earpiece Volume..................................................21 Ringer Volume......................................................22 Display Own Phone Number ...............................22 Switch to Second Phone Number........................22 Place a Hands Free Call......................................24 Receive a Hands Free Call..................................24 Manual Handset to Hands Free Operation..........25 Automatic Hands Free .........................................25 Hands Free to Handset Operation.......................25 Memory ...............................................................26 Storing Information in Memory ............................26 Storing a Phone Number and a Name ................26 Storing Phone Number Only................................28 Storing Area Code and Prex (Postscripting)......28 Store to a Location Number.................................29 Memory Autoload.................................................29 Memory Blocks ....................................................30 1 Table of Contents Memory Protect ...................................................31 Recalling/Scrolling from Memory.........................31 Recalling/Scrolling by Name................................31 Recalling/Scrolling by Location Number ..............32 Last Number Recall .............................................33 Recalling Last 10 Numbers Dialed ......................33 Recalling an Area Code and Prex (Postscripting) ..34 Turbo Dial.............................................................34 One Touch Dialing Keys.......................................35 Super Speed Dialing............................................35 Scratch Pad Memory ...........................................36 Tone Dialing (Two-Part Calling) ...........................36 Pause Dialing (Memory Linking)..........................38 Calling Card Dialing .............................................40 One Touch Dialing Keys.......................................45 One Touch Emergency Dialing ............................45 Change Memory Entries - Alpha or Numeric ......46 Clear Memory Entries..........................................47 Features ..............................................................48 Feature Menu ......................................................48 To Select/Cancel Menu Features.........................49 Signal Strength Meter ..........................................49 Feature Status Review.........................................50 Microphone Muting ..............................................50 Auxiliary Alert.......................................................50 Number Preference..............................................52 Automatic Answer ................................................52 Multiple Key Answer.............................................53 Call Receive.........................................................53 Ringer ..................................................................54 Keypad Tones.......................................................54 Scratch Pad Tones ...............................................55 Remind Message.................................................55 2 Table of Contents PIN Code Activation.............................................56 Timers ..................................................................57 Individual Call Timer ............................................57 Resettable Call Timer ..........................................58 Cumulative Call Timer..........................................58 Individual Timer....................................................59 One-Minute Timer ................................................59 Security Features.................................................59 Electronic Lock.....................................................60 Change Unlock Code...........................................60 Display Unlock Code............................................60 Automatic Lock ....................................................61 Theft Alarm ..........................................................61 Change Service Level..........................................62 Master Reset .......................................................64 Master Clear ........................................................64 Language Selection .............................................64 Extended Talk ......................................................65 Ringer Style .........................................................65 Reference............................................................66 The Cellular System ............................................66 Service Area ........................................................66 Weak Signal Alert ................................................66 Switchhook and Enhanced System Services ......67 Roaming...............................................................67 Selectable System Registration ..........................68 Troubleshooting....................................................71 Quick Reference Feature Guide ..........................72 Message Glossary ...............................................74 Rules, Regulations, & Precautions ......................76 Index ....................................................................79 Patent Information................................................82 Memory Location Directory..................................83 3 Getting Started Welcome Thank you for selecting Motorola a world leader in cellular technology. All Motorola cellular phones are designed and manufactured in the United States to meet Motorolas exacting specifications and world-class quality standards. These phones withstand our rigorous durability tests including temperature, humidity, shock, dust, vibration, and a drop test. Product superiority is yours with Motorola. For information about your product or accessories for your product, please call Motorola at:

1-800-331-6456 1-800-461-4575 (Canada) For any information about your cellular service, please call your service provider (Carrier). Carriers Name ________________________ Carriers Phone Number _________________ 4 Getting Started You will need to have the following information when you inquire about your phone or service. Your ESN (electronic serial number) and MSN

(mechanical serial number) are located on the transceiver of your telephone. ESN Number_____________________________ MSN Number ____________________________ Model Number ___________________________ Cellular Phone Number ____________________ Unlock Code The sequential code of 123 is the standard unlock code programmed into all phones by the factory. It is often changed to the last three digits of your cellular phone number by the carrier. For easy access to this unlock code in the future, please list it here now: __ __ __.

(Please contact your place of purchase if your unlock code has been changed and you do not have this information.) Warranty Expiration Date ________________ Date of Purchase ______________________ 5 Getting Started Safety Information IMPORTANT: Read this information before using your wireless mobile phone. Exposure to Radio Frequency Signals Your wireless mobile telephone is a low power radio transmitter and receiver. When it is ON, it receives and also sends out radio frequency (RF) signals. International agencies have set standards and recommendations for the protection of public exposure to RF electromagnetic energy. International Commission on Non-Ionizing Radiation Protection (ICNIRP)1996 Verband Deutscher Elektrotechniker (VDE) DIN-

0848 United States Federal Commission, Radio Frequency Exposure Guidelines (1996) National Radiological Protection Board of the United Kingdom, GS 11, 1988 American National Standards Institute (ANSI) IEEE. C95. 1-1992 National Council on Radiation Protection and Measurements (NCRP). Report 86 Department of Health and Welfare Canada. Safety Code 6 These standards are based on extensive scientific review. For example, over 120 scientists, engineers, and physicians from universities, government health agencies, and industry 6 Getting Started reviewed the available body of research to develop the updated ANSI standard. The design of your phone complies with these standards when used as described under "Phone Operation."

IIMMPPOORRTTAANNTT:: To maintain compliance with the FCC's RF exposure guidelines, if you wear a handset on your body use only the Motorola supplied carrying case, holster or other body-worn accessory for this product and ensure that the antenna is at least 1 inch (2.5 centimeters) from your body when transmitting. Antenna Care Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could damage the phone and may violate local agency regulations. Carry Phone Operation Do not operate your carry phone when a person is within 4 inches (10 centimeters) of the antenna. A person or object within 4 inches (10 centimeters) of the antenna could impair call quality and may cause the phone to operate at a higher power level than necessary and expose that person to RF energy in excess of that established by the FCC RF Exposure Guidelines. Mobile Phone Operation Do not operate your mobile telephone when any person is within 12 inches (30 centimeters) of its vehicle-installed antenna. 7 Getting Started Driving Check the laws and regulations on the use of wireless telephones in the areas where you drive. Always obey them. Observe the following guidelines when using your phone while driving. Give full attention to driving--driving safely is your first responsibility. Use hands-free phone operation, if available. Pull off the road and park before making or answering a call if driving conditions so require. Electronic Devices Most modern electronic equipment is shielded from RF signals. However, certain equipment may not be shielded against the RF signals from your wireless phone. Pacemakers The Health Industry Manufacturers Association recommends that a minimum separation of six inches (6") be maintained between a wireless phone's antenna and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with the independent research by and recommendations of Wireless Technology Research. Persons with pacemakers:

should ALWAYS keep the phone more than six inches from their pacemaker when the phone is turned ON should turn the phone OFF immediately if you have any reason to suspect that interference is taking place 8 Getting Started Other Medical Devices If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from external RF energy. Your physician may be able to assist you in obtaining this information. Turn your phone OFF in health care facilities when any regulations posted in these areas instruct you to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy. Vehicles RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles. Check with the manufacturer or its representative regarding your vehicle. You should also consult the manufacturer of any equipment that has been added to your vehicle. Posted Facilities Turn your phone OFF in any facility where posted notices so require. Blasting Areas To avoid interfering with blasting operations, turn your phone OFF when in a "blasting area" or in areas posted: "Turn off two-way radio." Obey all signs and instructions. 9 Getting Started Potentially Explosive Atmospheres Turn your phone OFF and do not remove your battery when you are in any area with a potentially explosive atmosphere. Obey all signs and instructions. Sparks from your battery in such areas could cause an explosion or fire resulting in bodily injury or even death. Areas with a potentially explosive atmosphere are often but not always clearly marked. They include, but are not limited to: fueling areas such as gasoline stations;

below deck on boats; fuel or chemical transfer or storage facilities; areas where fuel odors are present (for example, if a gas/propane leak occurs in a car or home); areas where the air contains chemicals or particles, such as grain, dust, or metal powders; and any other area where you normally would be advised to turn off your vehicle engine. For Vehicles Equipped with an Air Bag An air bag inflates with great force. Do NOT place objects, including both installed or portable wireless equipment, in the area over the air bag or in the air bag deployment area. If in-vehicle wireless equipment is improperly installed and the air bag inflates, serious injury could result. MOB010699 10 Getting Started Introduction The cellular telephone you have selected represents the state-of-the-art in cellular telephones today. The listing below shows just a few of the exceptional features that your telephone provides. 14-character alphanumeric color LCD display 104 memories, including last number recall and scratch pad Last 10 Number Redial Turbo Dialing Three One Touch Dial Keys Signal Strength Meter Auto Answer Five Call Timers Emergency Dialing Menu Mode/Alphanumeric Directory Two System Registration Multiple Key Answer To help you become familiar with your telephones features, we will take you through a logical step-

by-step learning procedure. The tabs at the edge of the manual mark the different categories that the telephones operations have been broken into. Please read the general safety information on page 6, and the rules, regulations, & precautions on page 76, before operating the phone. 11 Getting Started Phone Overview NOTE The telephone you receive may not look exactly like the one shown on the facing page. All features will operate as indicated. Operating Display and Status Indicators Provide a visual indication of telephone numbers and messages associated with mobile telephone service. Green Dot Lights when unit is powered. In Use Lights when unit is in use. No Svc Lights when the unit is out of service range of a cellular system. Calls cannot be placed or received. Roam Lights when the unit is within range of a cellular system other than your home registered system. Three One Touch Dial Keys Allows for direct access to important phone numbers and carrier network services. Volume Keys Adjust earpiece, ringer, and speaker volume. Also:

scrolls forward. scrolls backward. Numeric Keypad Used to enter call information. Also:

, enters feature menu. or scrolls forward. or scrolls backward. 12 Getting Started In Use No Svc Roam 13 Getting Started Control Keypad Recalls and displays telephone numbers stored in memory. Clears the last digit entered when pressed and released. Press and hold to clear the entire display in the event of an error (does not affect numbers stored in memory). Initiates a call to the entered telephone number or answers a call. Controls power to the unit. Stores telephone numbers into any of the memory locations. Terminates a call in progress. Function Key Used in combination with other buttons for specific user-programmed functions (e.g.,

, activates lock mode). 14 Basic Operation Turn Phone On and Off 1. If your ignition is on and your telephone is off, press . 2. Press again to turn unit off. Most users find it convenient to have their mobile telephone turn on and off in conjunction with the vehicle ignition switch. If you want your mobile telephone to operate independently of the ignition switch, discuss this with your installer. We recommend that the engine be running when using your mobile telephone. Start-up Self Tests Each time the telephone is turned on, it performs a series of self tests, sounds a tone, and lights all display positions and status indicators to check their operation. Display Messages Message Explanation A1 B1 A2 B2 LOCKED If your phone is programmed for two cellular systems, one of these messages will appear in the display upon power up. These are reminders as to which system and phone number are currently in use. Indicates that the phone has been locked and cannot send or receive calls until unlocked. Refer to page 60, Electronic Lock. 15 Basic Operation Start-up Status Indicators Indicators Explanation In Use No Svc Roam In Use No Svc Roam In Use No Svc Roam In Use No Svc Roam On/Lock Indicator

(green light) Lights steadily to indicate the phone is on and fully operative Lights steadily to indicate the phone is locked and will not place calls In Use Indicator Lights steadily while a call is in progress No Svc (No Service) Indicator Lights steadily if phone is beyond range of a cellular service area Calls cannot be placed or received while lit Roam Indicator If flashing, you are accessing a service area outside of your home system Steady Illumination -

Roaming on a home type system Flashing - Roaming on a non-home type system 16 Basic Operation Place a Call 1. With power on, enter the number you wish to call. 2. Press . (You may leave the handset mounted while dialing.) The green In Use indicator will illuminate. You will hear conventional ringing as the call is processed, followed by the called party answering. Pick up the handset and bring it up to your ear, or leave the handset mounted and direct your conversation to the Hands Free microphone for a hands free call. If the green In Use indicator is extinguished, your call has been terminated. To Correct an Error To clear the last digit entered, press and quickly release . To clear the entire entry, press and hold until the entire entry is erased. Unsuccessful Call Attempts If you hear one of the following signals, you have not successfully completed your call. 17 Basic Operation Tone Tone fast busy

(reorder signal) System Busy alternating high/low tone

(intercept) No Service busy signal Description Cellular System Busy Press again before ending the unsuccessful call attempt to automatically redial the call (see Automatic Redial below), or press and dial the call again. Cellular System Could Not Complete the Call You may have tried to place a call before the green ON/LOCK indicator was lit to let you know your phone was fully operative. Either press again before ending the unsuccessful call attempt to automatically redial the call (see Automatic Redial below), or press and dial the call again. The Called Partys Line is Busy Automatic Redial Your telephone includes a convenient feature designed to make repetitive call attempts unnecessary when a cellular system is busy. If you receive an alternating high/low signal

(intercept), or the fast busy tone (reorder signal), followed by System Busy in the display when attempting to place a call and wish to retry the call, press before ending the unsuccessful call attempt. Redial is then displayed. Your telephone will make the call attempt continuously over the next four minutes. If four minutes is insufficient time, press to begin another cycle. You may terminate Automatic 18 Basic Operation Redial by turning off the phone or ignition, or by pressing . NOTE Automatic Redial applies when the system is busy, and will not engage when the called partys line is busy. End a Call Press or return the handset to its mount. The green In Use indicator will extinguish. If you have activated the Automatic Hands Free feature, you must press to terminate the call. You may terminate a call or procedure (except Master Reset and Clear) at any time by pressing . Receive a Call Press upon hearing the ring, or lift the handset to your ear. Power must be on to receive calls. Call in Absence Indicator If your phone is on and an incoming call is unanswered, Call is displayed. You must press or to cancel the message and clear the display. If you wish to receive the Call message while you are away from your vehicle, turn your phone on. When you return to your vehicle, press any key except , , or to check for incoming calls. 19 Basic Operation Signal Strength Meter The Signal Strength Meter (SSM) represents the relative strength of the signal received by your phone. The SSM is displayed as a bar graph following the letter S at the left side of the display. The S alone represents the lowest strength with each additional bar representing a stronger signal. S S==

WEAK SIGNAL STRONG SIGNAL The SSM appears every time you turn your phone on, unless this feature is turned off through the feature menu (refer to pg. 48). To best utilize the SSM, you should familiarize yourself with the relative signal strength levels and their associated call placement and call-in-

progress qualities. To deactivate the SSM, see pg. 49. Any messages, such as LOCKED, which display as a result of activation of a feature will take priority over the SSM. You will not see the SSM displayed in these cases. Volume Meter The Volume Meter represents the current volume setting and will display whenever you adjust the volume control. The volume level is displayed as a bar graph following the letter V at the left side of the display, with each additional bar representing a higher volume setting. 20 Basic Operation v v==

LOWEST HIGHEST VOLUME SETTING VOLUME SETTING The number of bars represents the number of volume steps for speaker, earpiece, and ringer volume. The volume levels can be adjusted by the use of and . Speaker Volume 1. With the handset mounted, press and hold

. This will raise the volume. 2. To lower the volume, press and hold . The number of bars on the Volume Meter will decrease. The maximum number of bars that will appear on the display is six bars. v==

Earpiece Volume Lift the handset and use and as described above. The maximum number of bars that will appear on the display is five bars. v==

21 Basic Operation Ringer Volume Press and use and as described above. The maximum number of bars that will appear on the display is six bars. v==

Display Own Phone Number 1. Press , . 2. The phone number that is currently active will be displayed. 3. When you have nished viewing, press . Switch to Second Phone Number 1. Press , , . 2. The display will go blank to conrm the switch and the newly activated number will appear. 3. When you have nished viewing, press . Your telephone can operate over two different home systems, if you have made proper arrangements with your Cellular System Operator. Both are designated as your home system but are accessed with separate telephone numbers. While you may switch from one system to the other, only one of the two can be active at any given time. Calls are placed and received through the active system only. If you have two phone numbers programmed into your phone, each time the telephone is turned on, 22 Basic Operation it displays a message indicating which home system type and phone number is currently active. The message shows the system type and phone number applied, as follows:

System Type and Phone Number Non-wireline or A type with phone number 1 Non-wireline or A type with phone number 2 Wireline or B type with phone number 1 Wireline or B type with phone number 2 Display A1 A2 B1 B2 If a call is placed to the inactive phone number, the caller will receive the recorded Not In Service message. When you turn your phone on, the telephone will remember which system was active when you turned it off. That system will stay active until you change to the other system with the sequence ,

, . You cannot switch systems during a call. If you enter the sequence during a call, the phone will wait until the call is terminated and the In Use indicator is extinguished before switching systems. Each system (and phone number) has its own Selectable System Registration state that you may program (see page 68). That is, you can select Home Only for system 1 (and phone number 1) and 23 Basic Operation Standard Mode for system 2 (and phone number 2). Whenever you switch back to System 1, your telephone will operate in Home Only mode again. The Roam indicator will operate based on the active system (see page 67 for detailed information on Roaming). For example, if your active system is A1 and you are roaming on a wireline (B) system, the Roam indicator will flash rapidly. Each system (and phone number) has its own cumulative and resettable call timers. You can only display the call timers of the active system

(and phone number). Place a Hands Free Call 1. Leaving the handset mounted, dial the number you wish to call. 2. Press . 3. When the called party answers, direct your conversation to the Hands Free microphone typically mounted on your vehicles sun visor. The In Use indicator will remain on and HF will display for the duration of the call. 4. Press to terminate the call. Receive a Hands Free Call 1. Press . 2. Direct your conversation to the Hands Free microphone. The In Use indicator will remain on and HF will display for the duration of the call. 3. Press to terminate the call. 24 Basic Operation Manual Handset to Hands Free Operation 1. If you are using the handset and want to switch to Hands Free operation, press , . 2. Mute will display. Note that M for Mute appears on . 3. Return the handset to its mount. 4. Press , again and HF will display. 5. Direct your conversation to the Hands Free microphone. Automatic Hands Free 1. Press , . 2. Scroll the menu by pressing or

( or ) until HANG UP FOR HF displays. 3. Press once to toggle this feature on (), and again to toggle it off (). 4. To exit the feature menu, press . This feature allows you to automatically go to Hands Free operation without pressing , . NOTE You must first activate the Automatic Hands Free feature through the feature menu on page 48. To go from handset to Hands Free operation, hang up the handset and begin speaking. To go from Hands Free to handset operation, lift the handset. Hands Free to Handset Operation Lift the handset while in a call. 25 Memory Storing Information in Memory Your telephone provides memory capable of storing up to 99 frequently called phone numbers as well as a fourteen-character name tag. Upon entering a phone number in memory, the phone will prompt you to store an associated alphabetic name. If you are not interested in creating a name tag for the selected location, alpha entry may be bypassed and just the phone number would be stored. (Refer to page 28 for details.) Before setting up your memory, we suggest you read the rest of this section to become familiar with the ways in which you will access and use it. Storing a Phone Number and a Name 1. Enter phone number to be stored (up to 32 digits). 2. Press . 3. Enter two-digit location number or press for Autoload. 4. The phone will then automatically prompt for alphabetic name input. The Alpha Entry Mode display will ash ALPHA or sto. 5. Utilize the alphanumeric keypad to enter each letter as described below (up to 14 letters). advances to the next position. backspaces, if necessary. Repeat until name tag is complete. If you do not want to store a name tag, continue with Step 6. 6. Press . 7. Phone will conrm storage by displaying memory location number. 26 Memory Details on Utilizing Alpha Entry Mode Once in Alpha Entry Mode, you can enter letters using your numeric keypad. For example, A is at the first press of , B is at the second press of

, and C is at the third press of . Key 1st Press 2nd Press 3rd Press 4th Press A D G J M P T W B E H K N Q U X C F I L O R V Y S Z EXAMPLE To enter Bob and his phone number 555-1234 into memory location 01:

1. Enter phone number by pressing , , ,

, , , . 2. Press , , . The display will ash ALPHAor sto. 3. Press twice to select B. Press to advance to the next position. Press three times for O. Press . Press twice more to select the second B. 4. Press . The display will ash 01 to conrm that the name and phone number were successfully stored in memory location 01. 27 Memory NOTE If Full displays, refer to Memory Protect on page 31. Storing Phone Number Only 1. Enter the phone number you wish to store, up to 32 digits. 2. Press . 3. Enter two-digit location number or press for Autoload. 4. The phone is automatically in Alpha Entry Mode. The display will ash ALPHA or sto. Press to bypass. 5. Phone will conrm storage by displaying memory location number. NOTE If Full displays, refer to Memory Protect on page 31. Storing Area Code and Prex

(Postscripting) 1. Enter area code and prex to be stored. 2. Press . 3. Enter two-digit location number or press for Autoload. 4. The phone is automatically in Alpha Entry Mode. The display will ash ALPHA or sto. Enter a name or press to bypass. 5. Phone will conrm storage by displaying memory location number. NOTE If Full displays, refer to Memory Protect on page 31. Storing an area code and prefix for a frequently called location such as an office, offers a 28 Memory convenient means of postscripting the four-digit extension of the party you wish to call. To place a call from this type of memory location, simply recall the location and enter the four-digit extension before pressing . There are three ways to select a memory location. You can select a specific location number; you can choose to autoload which will store the information in the next sequentially available location; or you can arrange the directory into blocks. Store to a Location Number 1. Enter phone number to be stored. 2. Press . 3. Enter the two-digit location number in which you wish to place the entry. 4. The phone is automatically in Alpha Entry Mode. Enter a name or continue to step 5. 5. Press . 6. Phone will conrm storage by displaying memory location number. NOTE If Full displays, refer to Memory Protect on page 31. Memory Autoload 1. Enter phone number to be stored. 2. Press , . 3. The phone is automatically in Alpha Entry Mode. Enter a name or continue to step 4. 4. Press . 5. Phone will conrm storage by displaying the autoload memory location number. 29 Memory NOTE If Full displays, refer to Memory Protect on page 31. This procedure automatically stores memory entries into the next available memory location. This method serves particularly well if you do not remember the next available memory location. Memory Blocks 1. Enter phone number to be stored. 2. Press . 3. Enter the rst digit of the desired block

, , , etc. 4. Press . 5. The phone is automatically in Alpha Entry Mode. Enter a name or continue to step 6. 6. Press . 7. Phone will conrm storage by displaying memory location number. NOTE If Full displays, refer to Memory Protect on page 31. The directory can be arranged by location number in blocks of ten (0-9, 10-19, 20-29, etc.). Organizing your directory in this manner greatly speeds review or recall of entries that share a commonality: e.g., business associates, friends, emergency numbers, etc. You will still be able to recall your entries alphabetically. To take advantage of memory blocks, store entries into the next free location within a block of ten numbers (0-9, 10-19, 20-29, etc.). 30 Memory Memory Protect The directory has an automatic memory protect feature which prevents the accidental overwriting and loss of previously stored names and numbers in memory. If you attempt to store a number or name in a location that already contains an entry, the phone will display FULL and the name/number in that memory location. The display will then show the previously stored number and alternate between the name stored and CHANGE?. If you wish to save to that location, thus overwriting and erasing the old information, press . If you wish to store the entry in an alternate location, press , and the alternate location number. Memory autoload or memory blocks may also be used in this case (see pages 29 and 30). Recalling/Scrolling from Memory Information stored in memory can be recalled or reviewed by location number. You may also scroll the memory during a call. Pressing once in this case will cancel scrolling, but not the call. Recalling/Scrolling by Name 1. Press , . 2. Continually press or to scroll in alphabetical order until the desired name displays. 3. Press to place a call to the number displayed. 31 Memory Use and ( and ) to scroll forward and backward. To begin scrolling from a specific letter of the alphabet, press , , then the letter from which you wish to start. If no entries are stored under this letter, the unit automatically searches forward, alphabetically, until the next name is found. To view the associated phone number 1. Press . The display will ash the location number, then the phone number. 2. Press again to view the name. If you have the Name Preferred feature selected, the phone will rst show the alpha entry when you recall by the memory location. To view the location and phone number press

. Recalling/Scrolling by Location Number 1. Press . 2. Enter the desired two-digit location number. or Press , and press or to begin scrolling from the beginning of the stored locations. 3. The display will show the location number, then the rst 10 digits of the number, or if no number was entered, up to 14 characters of the name will display. 4. Press to place a call to the number displayed. 32 Memory Use and ( and ) to scroll forward and backward. To scroll from a specific two-digit location, press

, then the location number where you wish to begin scrolling. The phone will display an apostrophe () after the memory location number to indicate that memory scrolling is active. NOTE If you have the Name Preference feature selected, the above information is reversed. Refer to the Number Preference section on page 52 for more details. Last Number Recall 1. Press (optional, allows you to see number). 2. Press to place a call to the last number displayed. This feature automatically remembers the last phone number entered from the keypad or recalled from memory. Recalling Last 10 Numbers Dialed 1. Press , , . L0 will display followed by the name or number of the most recently placed call. 2. Scroll the last ten numbers dialed with and ( and ). 3. To place a call to a displayed number, press

. 33 Memory This feature allows you to refer to or redial any of the last ten phone numbers to which calls were placed. The numbers are stored in the order placed and always represent the ten most recent calls. Successive calls to the same number are stored only once, and all are retained when the unit is shut off. NOTE When scrolling, you may observe that a location number is skipped. This may be caused by pressing when the display is empty and does not mean that a number has been lost. Recalling an Area Code and Prex

(Postscripting) 1. Recall two-digit location number where an area code and prex is stored. 2. Add additional digits as needed. 3. Press . You can add additional digits to the end of recalled numbers by entering them before pressing . This is particularly useful if you often place calls to the same area code and prefix, e.g., an office, but need to reach different extensions with each call. Turbo Dial Press and hold for one second any one of the digit buttons through . The digit buttons through ( is reserved for Emergency Dialing) provide an advanced form of Super Speed Dialing. Once numbers have been stored in memory location 2-9, calls can be placed from these locations by pressing the associated 34 Memory key and holding for approximately one second. There is no need to press . NOTE If you wish to use memory location 1 for a non-emergency number, the Emergcy message may be deactivated through the feature menu

(refer to page 48). In order to prevent the accidental pressing of these keys, Turbo Dial can be deactivated through the feature menu. NOTE Turbo Dialing is affected by Call Restriction Service Levels 1, 2, 3, and 8 (see page 62). Do not select these service levels if you wish to use Turbo Dialing. One Touch Dialing Keys Your phone has three special dialing keys, ,

, and , which allow for easy one touch access to numbers stored in these locations. See page 45 for more details on how to use these keys. Super Speed Dialing 1. Enter the location number. 2. Press . Memory locations 1-99 are equipped with Super Speed Dialing capability. Once information is stored in these locations, Super Speed Dialing allows you to place a call without pressing . The number dialed will not display for review. NOTE Do not attempt the sequence , . This will place a call to the local operator. 35 Memory Scratch Pad Memory The scratch pad permits entry of numbers from the keypad during conversation. If your party gives you another number to call, simply enter this from the keypad. If you make an error, press to erase the last digit entered or hold to erase the entire entry. Advise your party that they will hear tones as you store the number. To call the scratch pad number at the end of an ongoing conversation, press , . NOTE Refer to the Scratch Pad Tones feature

(page 55) for details on silencing the tones. Tone Dialing (Two-Part Calling) Your telephone provides the standard Dual Tone Multi-Frequency (DTMF) signals typically used to access alternate long distance services, signal pagers, answering machines, etc. Generally, these services use a two-part procedure: First, a call is placed from the memory or through the keypad to a central telephone number, then a secondary dial tone is heard and the additional tone digits are sent. To tone dial from the keypad, make the initial call. Append additional tone digits using the keypad. The tones are automatically sent as you press the keys. Do not press . EXCEPTION If you have selected silent scratch pad, you must press , after entering the additional digits. 36 Memory To tone dial from a memory location, place the initial call. Recall from memory (using , location number) the number you wish to send as DTMF digits. Press , . Repeat these steps as required to send separate groups of numbers. Two-part calling can be automated by a unique feature which permits the programming and memory storage of pauses between groups of numbers. When recalled or sent, the telephone stops transmitting at the pause and waits for your response (i.e., secondary dial tone). Two methods of Pause Dialing are explained below:

Memory Linking is used when constant number sequences are required, such as banking inquiries, answering machines, and voice mail. Calling Card Dialing provides you with a method for storing lengthy calling card information in the phones memory and sending this information quickly and easily. Once this information is stored, a few key presses will transmit the linked information. The phone will even prompt you to insert the number you wish to call. 37 Memory Pause Dialing (Memory Linking) 1. Enter the rst group of numbers from the keypad or recall them from memory using . 2. Insert a pause by pressing , . will appear where the pause is inserted. To store, press . 3. Enter the next group of numbers, or recall them from memory by pressing , , two-digit location number. 4. Repeat this sequence for as many groups as you wish up to a maximum of 32 digits.

(Each pause occupies a digit.) EXAMPLE To construct a number sequence which you might use to inquire about your bank balance, follow this example. The entry sequence required by the bank is to call the access number, wait for the tone, enter your ID number followed by , wait for the tone, then enter your account number and . The banks telephone number is 123-4567. Your ID number is 888. Your account number is 22. NOTE Pressing or may be required by the bank. 38 Memory Display 1234567 INSERT PAUS 1 234567 12345 67888C INSERT PAUS 123456 7888C 345678 88C22C ALPHA or sto 1 2 3 4 5 6 7 8 Instruction and Key Sequence Enter the phone number of the bank , , , , ,

, or recall it from memory location xx , x, x Create a pause

, Press Enter the ID number and a pound sign , , , or recall it from memory location xx , , x, x Create another pause

, Press Enter the account number and a pound sign , , To store number, press and the two-digit location number. Press to bypass the Alpha message in the display. The memory location number will be displayed to confirm storage. To place a linked call, press to transmit the first group of numbers, prior to the first pause. 39 Memory After waiting for the system response, press to send the second group of numbers. Continue to press until all digit groups are sent. If the PIN code feature is activated (see page 56), the PIN code will automatically be sent after the first pause by pressing . To store a linked sequence, press , then enter the location number where you wish to store the number. Each memory location will only accept up to 32 digits. NOTE Long Tone DTMF signals cannot be sent using this procedure. If Long Tone DTMF signals are required, they must be sent manually. The tone will be sent for as long as the key is depressed. NOTE Do not add the PIN code to the linked sequence. Your phone will automatically insert the PINcode when placing a linked call. Follow the instructions on page 56. Calling Card Dialing The following is a typical example of information required to make a credit card call. The order of information may vary depending on your service provider. The information provided below is designed to accommodate credit card dialing for the three major long distance carriers. To enter your calling card number into memory:

1. Enter your calling card access phone number. (Typically this is a 1-800 phone number or a 0. If a 0, skip to step 4.) 2. Insert a pause by pressing , , . will appear where the pause is inserted. 40 Memory 3. Press . (Long distance carriers typically require that a 0 be placed before the number you are calling.) 4. Press , , . NUM N will display. This serves as a marker for the spot where the phone number you wish to call will be automatically inserted into the sequence. 5. Press . This stores the N character. 6. Insert another pause by pressing , ,

. will appear where the pause is inserted. 7. Enter your credit card PIN number. 8. Press and one of the three One Touch Dial keys or Turbo Dial locations (1-9). 9. The phone will then automatically prompt for alphabetic name input. Enter a name and then press or simply press to bypass the addition of an alphabetic name. 10.The phone will conrm storage by displaying STORED for One Touch Dial keys or the memory location number for Turbo Dial locations. This feature provides you with a convenient method for saving your credit card calling information in the phones memory. You can then readily place calls without having to enter your credit card information every time you place a credit card call. Your credit card call can conveniently be sent to a phone number stored in any memory location or you can dial the phone number through the keypad. The only requirement is that the number you wish to call through memory recall or dialing, must include the area code. 41 Memory Instruction and Key Sequence Enter the access number. Enter a pause , Press Press Enter a pause , Press Press Enter a pause , 1 2 3 4 5 6 7 8 9 Press Display 1800 1234567 INSERT PAUS 18001 234567 180012 345670 INSERT PAUS NUM N 8001234 5670 N INSERT PAUS 0012345 670 N 670N 8901234 Enter your credit card PIN number To store number, press and the One Touch Dial key or the Turbo Dial key. Press again to bypass Alpha display. The memory location number will be displayed to confirm storage. If you stored the number in a One Touch Dial location, STORED will be displayed to confirm storage. 10 11 42 Memory To place a call using your credit card:

1. Recall and send the credit card memory location. You can do this in the following ways:

a. If the credit card number is stored in a One Touch Dial location, simply press and hold the appropriate One Touch Dial key for one second. b. If the credit card number is stored in a Turbo Dial location (1-9), simply press and hold the appropriate key for one second. 2. The display will ash Enter Number. This is the prompt to enter the phone number you wish to call. 3. Enter the phone number you wish to call or recall it from memory. Note that the area code must be included. You may enter and send the phone number in the following ways:

a. Enter the number manually. The number must be three or more digits. Press to initiate the call. b. Enter the Turbo Dial location where the number is stored. You do not need to press to initiate the call. c. Enter and the two-digit memory location. Press to initiate the call. 4. The call is now initiated. The rst group of numbers will be transmitted (i.e., the access number or number you are calling). After waiting for the system response, press the One Touch Dial key to send the second group of numbers (i.e., the number you are calling or the credit card PIN number). If a third group is required for your credit card, 43 Memory wait for the next system response and press the One Touch Dial key again. IMPORTANT If your credit card number is stored in a Turbo Dial location, you must press rather than the Turbo Dial key to send additional groups of numbers. EXAMPLE Use the credit card information stored in One Touch Dial location 1 to place a credit card call to a ten-digit phone number stored in memory location 3. Instruction and Key Sequence 1 2 Recall and send your credit card number. In this example, use One Touch Dialing. Press and hold for one second. Enter and send the phone number you wish to call. In this example, memory location 3 is sent via Turbo Dialing. Press and hold for one second. (The Signal Strength Meter will display and the In Use light will begin to flash to let you know that the call has been initiated.) 3 Send the final series of digits

(i.e., your credit card PIN number) after you hear the system response. (You will hear the tones as the digits are sent.) Display ENTER NUMBER S S 44 Memory One Touch Dialing Keys Press and hold the One Touch Dial Key

, , or . To Store a Number 1. Enter phone number to be stored. 2. Press . 3. Press specic One Touch Dial Key. 4. The phone is automatically in Alpha Entry Mode. Enter a name or bypass by pressing

. 5. Phone will conrm storage by displaying Stored. These keys function like Turbo Dial keys. When you press and hold , , or , a call is placed to the number stored in that position. To recall the number, press , and the specific One Touch Dial Key. To clear the number, press , , and the specific One Touch Dial Key. ALPHA or sto will appear. Press . The unit will display the name and number along with Change?. Press to clear both name and number. One Touch Emergency Dialing 1. Press and hold . 2. Emergcy will display. Memory location 01, a Turbo Dial location, may be used for 911 or any other emergency number you may wish to dial even if your phone is locked. NOTE Do not select Call Restriction Service Levels 1, 2, 3, or 8 if you wish to use One Touch Emergency Dialing. 45 Memory Emergency dialing can be deactivated by using the feature menu found on page 48. When this feature is deactivated, the number stored in memory location 01 will still be dialed if the phone is unlocked and if you press and hold , but Emergcy will not display. NOTE Automatic Redial does not work with emergency dialing while the phone is locked. Change Memory Entries -

Alpha or Numeric 1. Press and the two-digit location number. 2. Press again, if necessary, so that the phone number to be changed is displayed. 3. Edit phone number by pressing to back out the digits to be changed. Enter new digits. 4. Press and the same two-digit location number. 5. ALPHA or sto will be displayed. 6. Change or add alpha name tag if desired. To edit name, press to back out the letters to be changed. Enter new alpha characters.

(Enter alphabetic characters as described on page 27.) 7. Press . 8. You will see a Memory Protect message;

press to overwrite. 9. Memory location number will display as conrmation. NOTE See Number Preference feature on page 52 for more details on step 2 above. 46 Memory Clear Memory Entries Clearing via Memory Name 1. Press , to enter alphabetic memory. 2. Review the memory locations using memory review (see page 31), and recall the entry you wish cleared. 3. Press . The unit will display Clear?. 4. Press to clear both name and number. or Press to exit without deleting the entry. Clearing via Memory Location Number 1. Press , , and the two-digit location number to be cleared. 2. ALPHA or sto will display. Press to bypass. 3. The phone will display Full, ash number in memory, followed by Change?. 4. Press to clear. or Press to exit without deleting the entry. 47 Features Feature Menu The feature menu permits review, selection, and cancellation of most of your telephones features through the keypad and display. The chart below shows all features available through the menu and the pages where detailed information is found. Feature Page Auto Answer Auto Lock Call Receive Emergency Call Extended Talk HF Auto Individual Timer Keypad Tones Multi Key Answer Number Preferred One-Minute Timer PIN Active Remind Message Ringer On Ringer Style Scratch Pad Tones Select Language Signal Meter Theft Alarm Turbo Dial 48 52 61 19 45 65 25 59 54 53 52 59 56 55 54 65 55 64 49 61 34 Features Additional telephone features, that may be available with your phone but are not accessed through the feature menu, are also described in this section. To Select/Cancel Menu Features 1. Press , . 2. Scroll the menu by pressing or

( or ) until the desired feature displays. 3. Press to toggle the feature off or to activate. 4. Press to exit the feature menu. EXAMPLE To activate silent keypad, press ,

, and scroll with or until the display shows keypad tone on. Press to deactivate this feature. The display will then show keypad Tone Off. Press to exit the menu. Signal Strength Meter To Disable the SSM from Displaying 1. Press , . 2. Scroll the menu by pressing or

( or ) until signal meter on displays. 3. Press once to disable the SSM. To reactivate the SSM press . 4. Press to exit the feature menu. See page 20 for more details on the operation of the SSM. 49 Features Feature Status Review To Review Status 1. Press , , , . 2. Press or ( or ) to scroll messages. 3. To activate a feature that is displayed press

.. To deactivate a feature press . To End Review Press . Microphone Muting To mute microphone Press , . To disable mute Press , again. This feature allows you to confer privately with others in the car during a call. It will disable the microphone and display Mute. Note that M for Mute appears on . The mute feature is canceled if you end your call. Auxiliary Alert 1. Press , with the unit on, unlocked, and Theft Alarm and Silent Ringer inactive. ALERT will display. 2. Turn off the vehicle ignition. The Auxiliary Alert feature allows an additional alerting device (horn or lights) to be activated for the first five rings (20 seconds) of an incoming 50 Features call. This is useful if you intend to be outside of the vehicle and expect a call. NOTE Determination of whether the Auxiliary Alert feature is desired and, if so, which alerting device is to be used is made at the time of installation. Note that H for Horn appears on . The external alerting device (horn or lights) will only respond if the vehicle ignition switch has been turned off. NOTE A call cannot be in progress when you enable Auxiliary Alert. Auto Answer is disabled during Auxiliary Alert. When the Auxiliary Alert mode is enabled, the mobile telephone remains on despite the vehicle ignition being turned off. Calls may be placed while in the Auxiliary Alert mode unless the unit has also been locked subsequent to pressing , . NOTE If left active for more than eight hours, the telephone will turn itself off to preserve your vehicles battery. The Auxiliary Alert mode is automatically disabled the next time the ignition is turned from off to on. The Auxiliary Alert mode can also be disabled by pressing or by pressing , again. ALERT will turn off when the feature is disabled. 51 Features Number Preference 1. Press , . 2. Scroll the menu by pressing or

( or ) until number pref on displays. 3. Press once to toggle this feature off, and to toggle it on. 4. To exit the feature menu, press . The Number Preference feature reverses the display order of memory entries so that the number will be displayed before the name. Automatic Answer 1. Press , . 2. Scroll the menu by pressing or

( or ) until auto ansr off displays. 3. Press once to toggle this feature off, and to toggle it on. 4. To exit the feature menu, press . This feature permits you to answer calls without pressing . When your phone receives a call, it will ring twice, then activate the Hands Free system. NOTE We suggest that you do not select the Automatic Answer and Silent Ringer simultaneously since incoming calls will then be announced only by the flashing Call in the display. Also, this feature may be incompatible with certain enhanced system services, such as no-answer transfer. Consult your Cellular Service Provider. 52 Features Multiple Key Answer 1. Press , . 2. Scroll the menu by pressing or

( or ) until multkey ansr off displays. 3. Press once to toggle this feature off, and to toggle it on. 4. To exit the feature menu, press . The Multiple Key Answer feature allows you to answer an incoming call by pressing or any digit key through . Call Receive 1. Press , . 2. Scroll the menu by pressing or

( or ) until Call rcv on displays. 3. Press once to toggle this feature off, and to toggle it on. 4. To exit the feature menu, press . Use this feature if you prefer not to receive incoming calls but wish to be informed of the attempt. If your cellular service offers No-Answer Transfer, the calls received while this feature is in effect can be routed to a secretary or answering machine. When the phone is on and this feature is selected, incoming calls are signaled by several short bursts of tone, Call in the display, and the green on indicator. Without No-Answer Transfer, the caller will receive the Not in Service recording. As a reminder that incoming call screening is selected, the unit will sound the special tone burst each time it is turned on. 53 Features NOTE We suggest you do not select Incoming Call Screening and Silent Ringer simultaneously since the incoming call will not be signalled by a short burst of tone. Ringer 1. Press , . 2. Scroll the menu by pressing or

( or ) until ringer on displays. 3. Press once to toggle this feature off, and to toggle it on. 4. To exit the feature menu, press . The telephones ring tones may be silenced where they could prove a distraction, as during a business conference, etc. In this case, incoming calls are announced only by a flashing Call in the display. NOTE We suggest you do not select the Silent Ringer and Automatic Answer simultaneously, since the phone will then answer a call without audible indication. Keypad Tones 1. Press , . 2. Scroll the menu by pressing or

( or ) until Keypad tone on displays. 3. Press once to toggle this feature off, and to toggle it on. 4. To exit the feature menu, press . When selected, this feature silences the tones used to indicate keypad depressions. 54 Features Scratch Pad Tones 1. Press , . 2. Scroll the menu by pressing or

( or ) until scrpad tone on displays. 3. Press once to toggle this feature off, and to toggle it on. 4. To exit the feature menu, press . Use this feature to enter scratch pad numbers during a call without transmitting DTMF tones. You will hear the tones, but your called party will not. NOTE Should you wish to transmit DTMF tones

(to access answering machines, pagers, automatic menus, etc.) while Silent Scratch Pad is activated, enter the digits and press , . Remind Message 1. Press , . 2. Scroll the menu by pressing or

( or ) until Remind Msg off displays. 3. Press once to toggle this feature off, and to toggle it on. 4. To exit the feature menu, press . Reminder tone is an audible message to alert the user that they have received a short message. It will beep every two minutes until the new messages are read. Your cellular carrier may offer enhanced features, such as short messaging. Ask your cellular service provider if this is supported in your system. If short messaging is not supported in your system, reminder beep selection will have no effect. 55 Features PIN Code Activation Activate PIN Code 1. Press , . 2. Scroll the menu by pressing or

( or ) until pin inactive displays. 3. Press once to toggle this feature off, and to toggle it on. 4. To exit the feature menu, press . Store PIN Code in Memory Location 07 1. Enter PIN code. 2. Press . 3. Press , . Place a Call With PIN Code Active 1. Enter number to be called, or recall from memory. 2. Press .Wait for double tone beep, beep. 3. Press . The phone will automatically send the PIN code stored in memory location 07. Your cellular carrier may require a personal identification number (PIN) when placing outbound calls. This code assures the cellular system that the person placing the call is an authorized user. Ask your cellular service provider if this is required in your system. Only select this feature if your cellular service provider requires it. This feature will allow you to automatically send your PIN code with all outbound calls. If Invalid PIN displays, check to see if you have activated the feature in the menu without storing a PIN 56 Features number in memory location 7. The PIN code must be less than seven digits. If you enter a service area which does not require a PIN code, disable the feature in the feature menu. Timers Call timers provide a useful means of monitoring the air-time spent in conversation. Several of these operate in the background and can be displayed at any time. Another offers tones heard only on your side of the conversation. Each timer begins counting as a cellular channel is assigned, or when the phone rings to signal an incoming call. If an incoming call is not answered, the timers revert to their previous values. Individual Call Timer To Display Press , , . This timer accumulates the air-time of a call in minutes and seconds. It automatically resets before a new call is placed and when the phone is turned off. 57 Features Resettable Call Timer To Display Press , , , . To Reset Press , , , . This timer accumulates the air-time in minutes from the point at which it is reset. This resettable timer is generally utilized to track monthly air-time usage and is set in conjunction with the monthly billing cycle. NOTE If you have two phone numbers programmed in your phone, each phone number has its own resettable call timer. To view the resettable call timer associated with the other phone number, switch your phone to that number, then use the sequence above. Cumulative Call Timer To Display Press , , , , . This is a non-resettable timer which accumulates the phones total air-time in minutes, starting with the initial factory setting. NOTE If you have two phone numbers programmed in your phone, each phone number has its own cumulative call timer. To view the cumulative call timer associated with the other phone number, switch your phone to that number, then use the sequence above. 58 Features Individual Timer 1. Press , . 2. Scroll the menu by pressing or

( or ) until indiv timroff displays. 3. Press once to toggle this feature off, and to toggle it on. 4. To exit the feature menu, press . This feature automatically displays the accumulated time in minutes and seconds during and after each call. One-Minute Timer 1. Press , . 2. Scroll the menu by pressing or

( or ) until one min timroff displays. 3. Press once to toggle this feature off, and to toggle it on. 4. To exit the feature menu, press . This timer provides a tone ten seconds before the end of each minute during calls. Security Features Your telephone offers several forms of security against unauthorized use. These require either your three-digit unlock code, or the six-digit security code. The factory programmed unlock code is 123 and the factory programmed security code is 000000. 59 Features Electronic Lock To Lock 1. Press , . 2. Lock? will display. 3. Press to lock. 4. Press to exit. To Unlock Enter your three-digit unlock code. If you make an error, press and start again. The electronic lock prevents use of the telephone by disabling both incoming and outgoing calls. To help remember which key to use, note that L for Lock appears on . If a call is received during this period, the phone will ring and you must enter the unlock code before the call can be answered. Change Unlock Code 1. Press , . 2. Enter your six-digit security code. 3. Enter the new desired three-digit unlock code. 4. Press . The new unlock code will display to conrm storage. Display Unlock Code 1. Press , . 2. Enter your six-digit security code. 3. Press . The phone will display loccode and the three-digit unlock code. 60 Features NOTE Use this procedure if you have forgotten your current three-digit unlock code. Automatic Lock 1. Press , . 2. Scroll the menu by pressing or

( or ) until auto lock off displays. 3. Press once to toggle this feature off, and to toggle it on. 4. To exit the feature menu, press . This feature automatically locks your phone each time it is turned off. Theft Alarm To Select (On) 1. Press , . 2. Scroll the menu by pressing or

( or ) until theft alrmoff displays. 3. Press once to toggle this feature off, and to toggle it on. 4. Press to exit the feature menu. The phone will display Armed. 5. Enter the phone number to be called or recall a number from memory. 6. Turn off the ignition. Your telephone will turn off as well. To Cancel (Off) 1. Turn on the ignition. 2. Enter your three-digit unlock code within 30 seconds. When the theft alarm is selected or an unauthorized person turns on your phone and does 61 Features not enter your unlock code within 30 seconds, an alerting call will be placed to the phone number you have stored in this feature. If the phone receives a busy signal, it will repeat the call automatically. Anyone answering the call will hear alternating high and low pitched tones (siren). If you elected to have the Auxiliary Alert feature installed, the auxiliary alerting device will also be activated. The phone will then repeat the call. The removal of the control unit will not prevent your mobile telephone from attempting to place the call. However, if the antenna has been removed, the phone will be prevented from successfully completing the call. The Auxiliary Alert device will still be activated. NOTE If you inadvertently trip the theft alarm and the alarm call is placed, you can stop the alarm by entering your three-digit unlock code. This feature must be reset in the feature menu each time the phone is disarmed. If PIN code is activated, the theft alarm will not work as the PIN code must be sent manually in order to complete the call. Change Service Level 1. Press , . 2. Enter your six-digit security code. 3. Enter the number of the service level you wish to use. 4. Press . The phone will display service level and the number selected. 62 Features Your telephone can be set to restrict call placement (as when lending the phone to another person). Using the six-digit security code, you may select one of the following levels of restriction. Service Level No restrictions. (Standard setting) Full keypad and directory dialing. No storage in directory locations 1-10 or One Touch Dial locations. Keypad dialing only. No directory or Turbo Dial access. Phone will place calls from all directory locations (, - , ). No keypad dialing. No directory change or storage. Seven-digit (local) dialing only, including directory and message calls (if seven digits or less). Phone will place calls only from directory locations 1-10 (, -

, ). If locations 1-10 are cleared, no outgoing calls can be made. No keypad dialing. No directory or One Touch Dial storage. Turbo Dial and One Touch Dial locations are restricted from display access. 4 6 3 2 5 1 8 To change the phone to unrestricted operation, use the procedure above and enter service level 4. 63 Features Master Reset CAUTION Once begun, this procedure cannot be canceled or reversed. 1. Press , . 2. Enter your six-digit security code twice. 3. Press , . This feature allows you to reset the user selectable options to their standard settings. Master Clear CAUTION Master Clear performs all the functions of Master Reset, in addition to erasing all names and numbers stored in memory, and clearing the Resettable Call Timer. Once begun, this procedure cannot be canceled or reversed. 1. Press , . 2. Enter your six-digit security code twice. 3. Press , . Busy may display. You must wait for this to clear before operating the phone further. It may take several minutes, depending on how full your dialing memory is. Do not turn the phone off during this operation. Language Selection 1. Press , . 2. Scroll the menu by pressing or until Select Languag displays. 3. Press to select this feature. 4. Scroll through menu by pressing or

. 64 Features 5. Press to choose the desired language. 6. To exit the feature menu, press . This feature allows you to change the language that your menus and messages are displayed in. You can choose from four different languages

(English, Spanish, French and Portuguese). Extended Talk 1. Press , . 2. Scroll the menu by pressing or until Extend Talk On displays. 3. Press once to toggle this feature off and to toggle it on. 4. To exit the feature menu, press . The extended talk feature allows you to conserve battery power when operating in a strong signal area. Ringer Style 1. Press , . 2. Scroll the menu by pressing or until Ringer Style _ displays. 3. Press to select this feature. 4. Press - to sample the different ringer styles. 5. Press to select the desired ringer style. 6. To exit the feature menu, press . This feature allows you to select one of nine different ringer styles to differentiate when your phone is ringing. When selected, the phone will give you a brief sample of that ringer style. 65 Reference The Cellular System There are generally two types of cellular systems serving any metropolitan area. One of these will most likely be operated by the telephone company that provides telephone service to your community, generally referred to as a wireline carrier. The other cellular service provider is a radio common carrier, referred to as a non-wireline carrier. Your Cellular Service Operator will provide information concerning specific features, procedures, and coverage in your particular area. Service Area The area within which the telephone operates is defined by your cellular service provider. Since this is a radio system, no exact boundaries (as on a map) can be drawn. The red No Svc (No Service) indicator will be displayed if you are beyond range of a service area. There may be locations within your area, such as tunnels and underground parking facilities, where the phone may act as if it were beyond range. Weak Signal Alert If you are called while in a location the system determines is inadequate for high quality service, you may hear a series of beeps to inform you of the call attempt. The caller will receive the recorded not in service message, Call will display, and the green on indicator will flash quickly. If this occurs, you must press before 66 Reference the phone will operate. Most systems do not impose air-time charges for such call attempts. NOTE This indicator is controlled through the initial programming of your phone and is usually deactivated. Refer to the Programming Guide under Step 11 for more details. Switchhook and Enhanced System Services Press . During a call, pressing performs a switchhook function used to access enhanced Cellular System features such as call waiting and conference calls. For the functioning of these features with , consult your Cellular Service Provider. Roaming The term Roaming applies to the use of cellular telephones within systems other than those designated as their Home system. Roam will be displayed whenever the phone comes within range of a visited system. As your phone begins to roam, it seeks service according to the conditions you have selected (see page 68). Steady illumination of Roam signals that your phone is accessing a home type system, while flashing indicates the phone is attempting connection through a non-home type system. Contact your system operator, or that of the visited system, for information on dialing and billing procedures. 67 Reference To use alternate long distance services when roaming, be certain to dial the appropriate area code and local number to access the alternate carrier in the visited area. Then use the tone dialing sequence described on page 36. If you selected two-system operation (see page 22), enter , to verify the currently active number. This is especially important if your two home systems have different area codes, or if Roam is flashing within your home service area. Selectable System Registration To Review Current Setting 1. Press , . The display will show the current active system choice. 2. Press to exit without changing selection. To Select (On) 1. Press , . The display will show the current active system choice. 2. Repeatedly press to review the system type modes. (Press to exit without changing selections.) 3. If you chose Prefd SIDs, press and then enter the ve-digit number at this time. Use and to move to the next SID location. 4. Press to activate the displayed selection. 5. Press to exit. 68 Reference System Type Selection Your telephone seeks cellular service according to the mode you have selected. If you have selected two-system operation, the phone seeks cellular service according to the system type mode selected for each phone number. Constant flashing of Roam, or a steadily lit No Svc while within your home service area may indicate an unintentional choice has been made. If this occurs, re-enter system type selection to see if the unit is operating in standard mode, or if an alternate selection has been made. 69 Reference System Type Selection Display Standard Mode Your phone first seeks a home type system, then a non-home type. Invert Preference Mode Your phone first seeks a non-home type system, then home type. (Select this mode if in a fringe area of your home system or in certain roaming situations.) If home system is type A Fast flashing Roam = call on B system Slow flashing Roam = call on home type system Slow flashing In Use = call on home system If home system is type B Fast flashing Roam = call on A system Slow flashing Roam = call on home type system Slow flashing In Use = call on home system Home Only Mode Phone will not operate outside its home system. Scan A Mode Phone will operate only within A systems. Scan B Mode Phone will operate only within B systems. Enter SID Mode Unit will operate only within specifically identified systems. This choice requires entry of up to 60 system ID numbers for those systems over which you wish to operate. The SID digits are entered as obtained from your Cellular Service Operator. Std A B Std B A Scan B A Scan A B Home Scan A Scan B p scan 70 Reference Troubleshooting Is the unit locked?

See Electronic Lock, page 60. Is the No Svc (No Service) indicator lit?

See Status Indicators, page 16. Have you programmed a unique operating mode?

Constant flashing of the Roam indicator while in your home service area may indicate that an incompatible system type has been selected. See Roaming, page 67. Is the unit operating with non-standard settings?

You may have inadvertently selected improper operating characteristics. See Feature Status Review, page 50. Are you having difculty accessing devices such as answering machines which require longer access tones?

Your phone ships with Long Tone DTMF (Dual Tone Multiple Frequency) Signal enabled. Check your user NAM programming to be sure this feature is enabled. 71 Reference Quick Reference Feature Guide Basic Operation Turn It On . Lock , . Unlock Three-digit unlock code. Turn It Off . Place a Call Enter number, . Receive a Call , or lift handset to ear. End Call , or return handset to its mount. Volume Control Earpiece Lift handset, or . Speaker With handset mounted, press and hold or

. Ringer , then or . Store to Memory Number Only Phone number, , two-

digit location. To store in next available location, ,

. Memory Recall By Location , two-digit location. to place call. Super Speed Memory location, . Dialing Turbo Dialing Press and hold memory location (-) for one second. 72 Reference Feature Menu Enter Menu , . or (

or ) to scroll. Select Feature . Cancel Feature . Exit . Additional Features Status Review , , , . or

( or ) to scroll. Last Number , . Recall Display Own , . Number Activate Other , , . Number Mute Microphone , . Scratch Pad Enter numbers during call. to terminate call and to place call to scratch pad number. 73 Reference Message Glossary A A1 A2 ARMED B==

B1 B2 BUSY C CALL delayed HOME LEVEL 1 LEVEL 2 LEVEL 3 LEVEL 4 LEVEL 5 LEVEL 6 LEVEL 8 MUTE 74

(Apostrophe) Scrolling activated displayed as A Two System Operation (Active system is non-wireline, using phone number 1.) Two System Operation (Active system is non-wireline, using phone number 2.) Theft Alarm selected Battery Strength Meter (number of bars indicates relative level of strength) Two System Operation (Active system is wireline, using phone number 1.) Two System Operation (Active system is wireline, using phone number 2.) Master Clear functioning Precedes Cumulative Timer display

(also used to display ) Shows incoming call (also used to indicate call in absence) Delayed Call Placement activated System Type Selection Home Mode Service level selected Service level selected Service level selected Service level selected Service level selected Service level selected Service level selected Microphone muted ON R S==

SCAN A SCAN AB SCAN B SCAN BA Reference Telephone is on Precedes display of Resettable Timer Signal Strength Meter (SSM)

(number of bars indicates relative signal strength) System Type Selection (scan A only) System Type Selection (scan A type first, then B) System Type Selection (scan B only) System Type Selection (scan B type first, then A) All user features set to standard STD System Busy Cellular system is busy V==

Volume Meter (number of bars indicates relative volume level) 75 Reference Rules, Regulations, & Precautions The U. S. Federal Communications Commission and the Canadian Department of Communications regulate cellular radiotelephone service in their respective countries. It is important for you, the cellular radiotelephone user, to observe the applicable regulations when operating your cellular phone in either country. In addition to these U. S. and Canadian regulations, you may also be bound by certain state, provincial, territorial, and local rules and regulations, as well as by your cellular carriers tariff (the rates, terms, and conditions of its service). If you wish to use your cellular radiotelephone in both the U.S. and Canada, please consult with your system operator. Furthermore, you should remember that your cellular phone is a radiotelephone, i.e., it combines both wireline technology, as used in your home or ofce telephone system, and radio technology and that the scope of regulations and precautions is therefore broader than the scope of regulations and precautions relating to wireline-

only telephone usage. Some of the major points of consideration are set out below. Please note, however, that this Rules, Regulations, & Precautions section does not constitute legal advice; and is intended merely for general information purposes. If you have any specic questions, please contact your Cellular Carrier (System Operator). 76 Reference License If your home system is in the U. S., you do not require a separate license to operate your cellular telephone; obtaining a cellular telephone access number is sufcient to register you as a user. If your home system is in Canada, a separate license is required; your carrier will assist you in the licensing process. If you wish to use your cellular phone on both sides of the border, please contact your Cellular Carrier (System Operator). Denial of Service A cellular carrier may deny service temporarily, or terminate service for violation of any government regulations or of its tariff. Consumer Responsibilities Remember that the wireline and radio regulations with respect to harassing calls, false distress calls, obscene language, etc. apply to cellular phone usage. Privacy As a telephone user, you have come to assume a certain standard of privacy when you place or receive a telephone call via the traditional wireline systems. However, because cellular radiotelephones utilize radio transmissions to effect calls, the same standard cannot always be assured. While it is unlawful for an unauthorized person to divulge or use any information obtained from intercepting or listening in on conversations intended for others, you should not assume that your conversation is completely secure. Commercially available scanning equipment can 77 Reference permit a third party to monitor the radio channels used for cellular telephone calls. Interference No person shall interfere with or cause interference to any radio communication or signal. Equipment Modications The U.S. Federal Communications Commission has type-approved and the Canadian Department of Communications has granted technical acceptance to the model of cellular telephone which you have purchased, and both have allocated a specic frequency range for cellular service. No changes or adjustments are to be made to your cellular phone. 78 Reference Index Automatic Answer...........................................52-54 Automatic Hands Free...................................19, 25 Automatic Lock ....................................................61 Automatic Redial ......................................18-19, 46 Auxiliary Alert.................................................50, 62 Call in Absence Indicator.....................................19 Calling Card Dialing.......................................37, 40 Cancel Menu Features ........................................49 Change Memory Entries ......................................46 Change Service Level..........................................62 Change Unlock Code...........................................60 Clear Memory Entries ..........................................47 Cumulative Call Timer .........................................58 Delayed Call Placement ......................................74 Display Own Phone Number ...............................22 Display Unlock Code ...........................................60 Earpiece Volume .................................................21 Electronic Lock ..............................................60, 71 End a Call ............................................................19 Extended Talk......................................................65 Feature Menu .......12, 20, 25, 34-35, 46, 48-49, 73 Feature Status Review ..................................50, 71 General Safety Information..............................6, 11 Hands Free to Handset Operation.......................25 Incoming Call Screening.................................53-54 Individual Call Timer ............................................57 Individual Timer ...................................................59 Introduction ..........................................................11 Keypad Tones................................................49, 54 Language Selection .............................................64 Last Number Recall .................................11, 33, 73 Manual Handset to Hands Free Operation..........25 79 Reference Master Clear ..................................................64, 74 Master Reset .................................................19, 64 Memory Autoload...........................................29, 31 Memory Blocks ...............................................30-31 Memory Linking ..............................................37-38 Memory Location Directory..................................83 Memory Protect ........................................28-31, 46 Message Glossary ...............................................74 Microphone Muting ..............................................50 Multiple Key Answer ......................................11, 53 Number Preference ............................32-33, 46, 52 One Touch Dialing Keys................................35, 45 One Touch Emergency Dialing............................45 One-Minute Timer................................................59 Pause Dialing .................................................37-38 Phone Overview ..................................................12 PIN Code Activation.............................................56 Place a Call...........17-18, 29, 31-33, 35, 43, 56, 72 Place a Hands Free Call......................................24 Postscripting .............................................28-29, 34 Quick Reference Feature Guide..........................72 Recalling an Area Code and Prefix .....................34 Recalling by Location Number.............................32 Recalling by Name...............................................31 Recalling from Memory........................................31 Recalling Last 10 Numbers Dialed ......................33 Receive a Call ...............................................19, 72 Receive a Hands Free Call..................................24 Remind Message.................................................55 Resettable Call Timer ....................................58, 64 Ringer ..................................................................54 Ringer Style .........................................................65 Ringer Volume................................................21-22 Roaming .............................................24, 67-68, 71 80 Reference Rules, Regulations, & Precautions ................11, 81 Scratch Pad Memory ...........................................36 Scratch Pad Tones ........................................36, 55 Scrolling by Location Number..............................32 Scrolling by Name................................................31 Scrolling from Memory.........................................31 Security Features.................................................59 Selectable System Registration.....................23, 68 Service Area.................................57, 66, 68-69, 71 Signal Strength Meter........................11, 20, 49, 75 Silent Ringer .............................................50, 52-54 Speaker Volume ............................................12, 21 Store to a Location Number.................................29 Storing a Phone Number and a Name ................26 Storing Area Code and Prefix..............................28 Storing Information in Memory ............................26 Storing Phone Number Only................................28 Super Speed Dialing.......................................34-35 Switch to Second Phone Number........................22 Switchhook and Enhanced System Services ......67 The Cellular System ..................................6, 55, 66 Theft Alarm.........................................50, 61-62, 74 Timers......................................................11, 24, 57 To Select Menu Features ....................................49 Tone Dialing...................................................36, 68 Troubleshooting ...................................................71 Turbo Dial......................................34-35, 41, 43-45 Turn Phone On and Off .......................................15 Two-Part Calling .............................................36-37 Volume Meter ...........................................20-21, 75 Weak Signal Alert ................................................66 Welcome ................................................................4 81 Reference Patent Information Manufactured under one or more of the following US patents. D375734 D375932 D375952 D376127 5588041 5589796 5590177 5594778 5594951 D377792 D377934 5604050 5606730 D378366 5613229 5613863 5615233 5621763 PAT111398 4829274 4837534 D301476 4843621 4845772 D302015 4851966 4868576 4870686 D303656 4876552 4879533 D305427 4896124 4897873 D305717 4904549 4905288 4905301 D306293 D306441 D306594 4912602 4918732 4922178 4945570 4954796 4959851 4963812 4963843 4965537 4972355 4972432 4972455 4975808 4984290 D314173 D315330 D315346 D315543 D315559 D315565 5004992 D315907 5008925 D316417 D316859 5017856 5018188 5020091 5020092 5020093 5028083 5028859 5029044 5029233 5031028 5036532 5053924 5057762 D320780 5059885 5060294 D322783 D322955 5081674 5083304 D324024 D324388 5095503 D325028 D325583 5109536 D325915 5113436 5117450 5121047 5122480 5122722 D327061 5128834 D328302 5142551 5142696 5146620 5148471 5148473 5148961 5150359 5150384 5152006 5157693 5163159 5164652 5166596 5175759 5175874 D332261 5182749 D332785 5185566 5187809 5193223 5195106 5195108 5201069 5204977 5210793 5214675 5222104 5222251 D337332 5230007 5230093 5233633 5235492 5237257 5239127 5241545 5241548 5241650 5241693 5242767 D339582 5249302 5251331 D340710 5260988 5261119 5262710 5263052 5276707 5278994 D343173 5280637 D344087 5287553 5287555 5287556 D344511 5301365 5321847 D348880 5349588 5359696 5361400 5363071 5365549 D352497 5366826 D353131 D353361 5375143 5375258 5379324 D354055 D354062 5384825 D356084 5402447 5406146 5406562 D357224 D357457 5410741 D357680 D357681 5428836 D359734 D359735 D359959 5432017 D360632 5438684 D361070 5442680 5446763 5448763 5448771 5453997 D362840 5457744 5459640 5463646 5465412 5469177 5475752 D365094 D365817 5486843 5487184 5488335 5488649 D366872 5493198 5493714 5497126 5497382 D367640 5499394 5506490 D368696 5510693 5511235 D369162 5513078 D369359 5519303 5519346 5524276 5524278 D370463 5530922 5542116 5544250 D372481 5546275 5546380 D372896 5551078 5559471 D374424 D374872 5572193 5574976 5577268 D375732 D375733 4121218 4138681 4193036 4254382 4302845 4312074 4327319 4329666 4369516 4369522 4378603 4390963 D269873 4398265 4400584 4400585 D270835 D271491 Re.31470 4431977 4434461 4455534 4462098 D275951 4484153 4485486 4486624 D276809 4491972 D277667 4504834 D278708 4523155 4546329 4550426 4551696 4564821 D282169 4571595 4573017 4574243 4585957 4602218 D284759 D285439 4616314 4617520 D286778 4626309 4628529 4629829 4630304 4630305 4633141 4636593 4636741 D288432 Other patents pending 4648125 4649543 D288683 4654655 D289156 4662691 4667333 4668917 4670747 4672502 4680787 4681476 4683585 4692726 4704588 D292578 4706036 D292920 4710724 4711361 4715063 4716319 4716391 4723305 D294257 4727306 4727583 4730195 4734635 4736277 4737976 4740794 4741018 4741034 4742562 D295627 4746242 D295973 D295975 4751737 D296187 4761621 4764737 D297734 D297735 4777564 Re.32768 D299136 4797929 4798975 4800348 4802236 4809356 4811377 4811404 4827226 4827507 82 Reference Memory Location Directory Location Name Phone Number 83