FCC ID: IHDT6MU1 MOTOROLA ELITE FLIP

To reset go to setting menu and select factory reset This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. FCC Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. FCC Caution

-Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

-This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

Internal Photo Report No.T110823301 Page 7 of 10 Report No.T110823301 Page 8 of 10 Report No.T110823301 Page 9 of 10 Report No.T110823301 Page 10 of 10

External Photo Report No.T110823301 Page 1 of 10 Report No.T110823301 Page 2 of 10 Report No.T110823301 Page 3 of 10 Report No.T110823301 Page 4 of 10 Power Adapter Photo (Model : DC4050US0301) Report No.T110823301 Page 5 of 10 Power Adapter Photo (Model : FMP5541A) USB Cable Photo Report No.T110823301 Page 6 of 10

1 2 33 44 55 66 77 88 REVISIONS RECORD REVISIONS RECORD DESCRIPTION DESCRIPTION ZONE ZONE REV.REV. DATEDATE ECN. NO. ECN. NO. REDACTOR REDACTOR A B C D EE m m m m 7 0 9

. 5 4 DESIGNED DESIGNED BY MOTOROLA BY MOTOROLA FCC ID : XXX-XXX FCC ID : XXX-XXX IC : XXXXX-XXX IC : XXXXX-XXX SYNXXXXA HW 900 SYNXXXXA HW 900

!

YYDDD

,,,,

,,,, m m 5 0

. 2 1.44 mm

. m m 7 9 m m 0 2

. 3

!

m m 8 9

. 2 m m 0

. 3 m m 2 9

. 1 m m 0 0

. 7 DESIGNED BY MOTOROLA IC :109O-T6MU1 FCC ID :IHDT6MU1 SJYN0863A HZ 720 MADE IN CHINA CCAExxxxxxxxxx N136 YYDDD 3.00 mm 3.0mm 3.02 mm 3.63 mm

,,,,

,,,, 5.0mm 4.99 mm AA B C D EE 1.THIS DOCUMENT IS THE SOLE PROPERTY OF CHENG UEI PRECISION INDUSTRY CO., LTD. 1.THIS DOCUMENT IS THE SOLE PROPERTY OF CHENG UEI PRECISION INDUSTRY CO., LTD. AND SHOULD NOT BE USED IN WHOLE OR IN PART WITHOUT PRIOR WRITTEN PERMISSION. AND SHOULD NOT BE USED IN WHOLE OR IN PART WITHOUT PRIOR WRITTEN PERMISSION. 2.THE HAZARDOUS SUBSTANCE CONTAINED IN EACH HOMOGENEOUS MATERIAL SHALL COMPLY 2.THE HAZARDOUS SUBSTANCE CONTAINED IN EACH HOMOGENEOUS MATERIAL SHALL COMPLY WITHWITH THE LASTET VERSION OF FOXLINK'S GREEN PROCUREMENT STANDARD(DQS-ZZ09-13) . THE LASTET VERSION OF FOXLINK'S GREEN PROCUREMENT STANDARD(DQS-ZZ09-13) . 3.THE RESTRICTED SUBSTANCES NEED TO MEET CUSTOMER'S SPEC REQUEST:(CUSTOMER DOC. 3.THE RESTRICTED SUBSTANCES NEED TO MEET CUSTOMER'S SPEC REQUEST:(CUSTOMER DOC. NO.)NO.) RR CHENG UEI PRECISION INDUSTRY CO.,LTD CHENG UEI PRECISION INDUSTRY CO.,LTD INTENDED USE:

INTENDED USE:

TITLE:

TITLE:

Drawing name : DRW0001 / Model name : SPEAKER-FABRIC Drawing name : DRW0001 / Model name : SPEAKER-FABRIC 22 11 33 44 55 66 TOLERANCE UNLESS TOLERANCE UNLESS OTHERWISE OTHERWISE SPECIFIED ( ) SPECIFIED ( ) L <= 3 mm L <= 3 mm 3 < L <= 15 mm 3 < L <= 15 mm 15 < L <= 30 mm 15 < L <= 30 mm 30 < L <= 70 mm 30 < L <= 70 mm 70 < L <= 120 mm 70 < L <= 120 mm

> 120 mm

> 120 mm ANGLE (degree) ANGLE (degree) W1.000000; =

W1.000000; =

CRITICAL DIM CRITICAL DIM W1.000000; =

W1.000000; =

TOOLING DIM TOOLING DIM W1.000000; = PROCESS W1.000000; = PROCESS DIM (Cpk) DIM (Cpk) MAT'L.:

MAT'L.:

SEE NOTES SEE NOTES XXXX

= DIMENSION ID

= DIMENSION ID 0.050.05 0.080.08 0.10.1 0.150.15 0.20.2 0.30.3 1.01.0 Label Label APPD.:

APPD.:

CHKD.:

CHKD.:

DR.:DR.:

Ming Cheng 0731 Ming Cheng 0731 DWG. NO.:

DWG. NO.:

1.000 1.000 SCALE:

SCALE:

UNIT: mm mm UNIT:

77 1/1 1/1 PAGE:

PAGE:

REV.:

REV.:

88 A4A4

CHENG UE! PRECISION INDUSTRY CO.,LTD No.8 R&D Rd.,1,Science-Based Industrial Park,Hsinchu 300, Taiwan,R.O.C. Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern:

I, the undersigned, hereby authorize Mr. Alex Chiu / Director of Compliance Engineering Services, Inc., d.b.a. Compliance Certification Services and hereafter referred to as CCS, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Mr. Alex Chiu of CCS on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing CCS as our agent, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

) make claims regarding certification only in respect of the scope for which certification has been granted;

d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

f) use certification only to indicate the products are certified as being in conformity with specified standards;

g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

i) keep a record of all complaints made known to the us relating to the products compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested;

j take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Gd ~w |e " {

Eddy Wang Quality Manager CHENG UEI PRECISION INDUSTRY CO.,LTD REMARK:

L. This authorization letter will be sent along with your application when filing with the Certification Division. , 2. Please follow the format and type it on company letterhead and send original to us. 3. Authorized signature must be in agreement with grantee code contact in FCC database.

FCC ID: IHDT6MU1 20 July 2011 Authorization of Agent Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 RE: Grantee Code IHD. Authorization:

I, John Lewczak, the FCC contact for Grantee Code IHD, hereby authorize the following company

(agent) to act on behalf of Motorola Mobility, Inc. for the application specified below. This includes:

Form 731, Attestation Statement Exhibit, and Confidentiality Request Signatures. Technical Contact. Non-Technical Contact. Test Firm Contact Information. The grant should still be mailed to the applicant of record for Grantee Code IHD, and any audit requests should also be directed to the applicant of record. Authorized Agent:

Mr. Eddy Wang Cheng Uei Precision Industry Co.,Ltd. (Foxlink) Address: No.18,Chung Shan Rd.,Tu-Cheng City,Taipei Hsien,Taiwan 114 Specific Application:

FCC ID: IHDT6MU1 Contact Information:

Please contact me by telephone at (954) 723-6272, or by e-mail (John.Lewczak@motorola.com), if there are questions or additional information needed concerning this authorization Regards, FCC Liaison Motorola Mobility, Inc. 8000 W. Sunrise Blvd, Suite A Plantation, FL 33022 Motorola Mobility, Inc., 8000 W. Sunrise Blvd, Suite A; Plantation, FL 33022, USA Page 13B - 1

20 July 2011 Power of Attorney RE: Power of Attorney. FCC ID: IHDT6MU1 We, the undersigned Motorola Mobility, Inc. hereby authorize Cheng Uei Precision Industry Co.,Ltd.(Foxlink) to act on our behalf in all matters relating to any and all processes required in obtaining FCC Part 15 approval for FCC ID: IHDT6MU1, and any communication required with the national authority. Any and all acts carried out by Cheng Uei Precision Industry Co.,Ltd.(Foxlink) on our behalf shall have the same effects as acts of our own, subject to this Power of Attorney. This Power of Attorney will be effective between 20 July 2011 and 31 December 2011, and will expire thereafter. If you have any questions regarding this authorization, please dont hesitate to contact us. Sincerely yours, FCC Liaison Motorola Mobility, Inc. 8000 W. Sunrise Blvd, Suite A Plantation, FL 33022 Phone: (954) 723-6272

(954) 337-2377 FAX:

Mail:

John.Lewczak@motorola.com Motorola Mobility, Inc., 8000 W. Sunrise Blvd, Suite A; Plantation, FL 33022, USA Page 13A - 1

CHENG UEI PRECISION INDUSTRY CO.,LTD No.8 R&D Rd.,1, Science-Based Industrial Park, Hsinchu 300,Taiwan,R.O.C Bluetooth Declaration Per FCC 15.247 Requirements 1 Output power and channel separation of a Bluetooth device in the different operating modes:

The different operating modes (data~mode, acquisition-mode) of a Bluetooth device dont influence the output power and the channel spacing. There is only one transmitter which is driven by identical input parameters concerning these two parameters. Only a different hopping sequence will be used. For this reason the check of these RF parameters in one op-mode is sufficient. 2 Frequency range of a Bluetooth device:

Hereby we declare that the maximum frequency of this device is: 2402 - 2480 MHz. This is according the Bluetooth Core Specification (+ critical errata) for devices which will be operated in the USA. This was checked during the Bluetooth Qualification tests (Test Case: TRM/CA/04-E), Other frequency ranges ( e.g. for Spain, France, Japan) which are allowed according the Core Specification are not supported by this device. 3 Co-ordination of the hopping sequence in data mode to avoid simultaneous occupancy by multiple transmitters:

Bluetooth units which want to communicate with other units must be organized in a structure called piconet. This piconet consist of max. 8 Bluetooth units. One unit is the master the other seven are the slaves. The master co-ordinates frequency occupation in this piconet for all units. As the master hop sequence is derived from it's BD address which is unique for every Bluetooth device, additional masters intending to establish new piconets will always use different hop sequences. 4 Example of a hopping sequence in data mode:

Example of a 79 hopping sequence in data mode:

40, 21, 44, 23, 42, 53, 46, 55, 48, 33, 52, 35, 50, 65, 54, 67, 56, 37, 60, 39, 58, 69, 62, 71, 64, 25, 68, 27, 66, 57, 70, 59, 72, 29, 76, 31, 74, 61, 78, 63, 01, 41, 05, 43, 03, 73, 07, 75, 09, 45, 13, 47, 11, 77, 15, 00, 64, 49, 66, 53, 68, 02, 70, 06, 01, 51, 03, 55, 05, 04 5 Equally average use of frequencies in data mode and behaviour for short transmissions:

The generation of the hopping sequence in connection mode depends essentially on two input values:

1. LAP/UAP of the master of the connection 2. Internal master clock The LAP (lower address part) are the 24 LSBs of the 48 BD_ADDRESS, The BD_ADDRESS is an unambiguous number of every Bluetooth unit. The UAP (upper address part) are the 24 MSBs of the 48 BD_ADDRESS. The internal clock of a Bluetooth unit is derived from a free running clock which is never adjusted and is never turned off. For synchronisation with other units only offset are used. It has no relation to the time of the day. Its resolution is at least half the RX/TX slot length of 312.5 ps. The clock has a cycle of about one day (23h30). In most case it is Implemented as 28 bit counter. For the deriving of the hopping sequence the entire LAP (24 bits), 4 LSBs (4 bits) (Input 1) and the 27 MSBs of the clock (Input 2) are used. CHENG UEI PRECISION INDUSTRY CO.,LTD No.8 R&D Rd.,1, Science-Based Industrial Park, Hsinchu 300,Taiwan,R.0.C CHENG UE]! PRECISION INDUSTRY CO.,LTD No.8 R&D Rd.,1, Science-Based Industrial Park, Hsinchu 300,Taiwan,R.O.C With this input values different mathematical procedures (permutations, additions, XOR-operations) are performed to generate the sequence. This will be done at the beginning of every new transmission. Regarding short transmissions the Bluetooth system has the following behaviors:

The first connection between the two devices is established, a hopping sequence was generated. For transmitting the wanted data the complete hopping sequence was not used. The connection ended. The second connection will be established. A new hopping sequence is generated. Due to the fact that the Bluetooth clock has a different value, because the period between the two transmission is longer (and it cannot be shorter) than the minimum resolution of the clock (312.5 us). The hopping sequence will always differ from the first one. 6 Receiver input bandwidth and behaviors for repeated single or multiple packets:

The input bandwidth of the receiver is 1 MHz. In every connection one Bluetooth device is the master and the other one is the slave. , The master determines the hopping sequence (see chapter 5). The slave follows this sequence. Both devices shift between RX and TX time slot according to the clock of the master. Additionally the type of connection (e.g. single or multislot packet) is set up at the beginning of the connection. The master adapts its hopping frequency and its TX/RX timing according to the packet type of the connection. Also the slave of the connection will use these settings. Repeating of a packet has no influence on the hopping sequence. The hopping sequence generated by the master of the connection will be followed in any case. That means, a repeated packet will not be send on the same frequency, it is send on the next frequency of the hopping sequence. 7 Dwell time in data mode The dwell time of 0.3797s within a 30 second period in data mode is independent from the packet type (packet length). The calculation for a 30 second period is a follows:

Dwell time = time slot length * hop rate / number of hopping channels *30s Example for a DH1 packet (with a maximum length of one time slot) Dwell time = 625 us * 1600 1/s / 79 * 30s = 0.3797s (in a 30s period) For multislot packet the hopping is reduced according to the length of the packet. Example for a DH5 packet (with a maximum length of five time slots) Dwell time = 5 * 625 us * 1600 * 1/5 *1/s / 79 * 30s = 0.3797s (in a 30s period) This is according the Bluetooth Core Specification V 1.0B (+ critical errata) for all Bluetooth devices. There for all Bluetooth devices comply with the FCC dwell time requirement in data mode. This was checked during the Bluetooth Qualification tests. The Dwell time in hybrid mode is measured and stated in the test report. 8 Channel Separation in hybrid mode The nominal channel spacing of the Bluetooth system is 1Mhz independent of the operating mode. The maximum initial carrier frequency tolerance which is allowed for Bluetooth is feenter = 75 kHz. This was checked during the Bluetooth Qualification tests (Test Case: TRM/CA/07-) for three frequencies (2402, 2441, 2480 MHz). CHENG UEI PRECISION INDUSTRY CO.,LTD No.8 R&D Rd.,1, Science-Based Industrial Park, Hsinchu 300,Taiwan,R.O.C Additionally an example for the channel separation is given in the test report 9 Derivation and examples for a hopping sequence in hybrid mode For the generation of the inquiry and page hop sequences the same procedures as described for the data mode are used (see chapter 5), but this time with different input vectors:

* For the inquiry hop sequence, a predefined fixed address is always used. This results in the same 32 frequencies used by all devices doing an inquiry but every time with a different start frequency and phase in this sequence. e For the page hop sequence, the device address of the paged unit is used as input vector. This results in the use of a subset of 32 frequencies which is specific for that initial state of the connection establishment between the two units. A page to different devices would result in a different subset of 32 frequencies. So it is ensured that also in hybrid mode the frequency use equally averaged. Example of a hopping sequence in inquiry mode:

48, 50, 09, 13, 52, 54,41, 45, 56, 58, 11, 15, 60, 62, 43, 47, 00, 02, 64, 68, 04, 06, 17, 21, 08, 10, 66, 70, 12, 14, 19, 23 Example of a hopping sequence in paging mode:

08, 57, 68, 70, 51, 02, 42, 40, 04, 61, 44, 46, 63, 14, 50, 48, 16, 65, 52, 54, 67, 18, 58, 56, 20, 53, 60, 62, 55, 06, 66, 64 10 Receiver input bandwidth and synchronisation in hybrid mode:

The receiver input bandwidth is the same as in the data mode (1 MHz). When two Bluetooth devices establish contact for the first time, one device sends an inquiry access code, the other device is scanning for this inquiry access code. If two devices have been connected previously and want to start a new transmission, a similar procedure takes place. The only difference is, instead of the inquiry access code, an special access code, derived from the BD_ADDRESS of the paged device will be, will be sent by the master of this connection. Due to the fact that both units have been connected before (in the inquiry procedure) the paging unit has timing and frequency information about the page scan of the paged unit. For this reason the time to establish the connection is reduced considerable. 11 Spread rate / data rate of the direct sequence signal The Spread rate / Data rate in inquiry and paging mode can be defined via the access code. The access code is the only criterion for the system to check if there is a valid transmission or not. If you regard the presence of a valid access code as one bit of information, and compare it with the length of the access code of 68 bits, the Spread rate / Data rate will be 68/1. 12 Spurious emission in hybrid mode The Dwell in hybrid mode is shorter than in data mode. For this reason the spurious emissions average level in data mode is worst case. The spurious emissions peak level is the same for both modes. edb = word Pre. Name/Title: Eddy Wang / Quality Manager TEL: 886-2-22699888 ext.27051 FAX: 886-2-22699816 Email: Eddy_Wang@foxlink.com

Request for Confidentiality IHDT6MU1 CHENG UEI PRECISION INDUSTRY CO.,LTD No.8 R&D Rd.,1, Science-Based Industrial Park, Hsinchu 300,Taiwan,R.O.C Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Date: August 30, 2011 Subject:

FCC ID:

To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation ANT specification Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 2012/2/25 External Photos Internal Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Sincerely yours, Name/Title: Eddy Wang / Quality Manager Company Name: CHENG UEI PRECISION INDUSTRY CO.,LTD(Foxlink) Address: No.18, Chung Shan Rd., Tu-Cheng City, Taipei Hsien, Taiwan TEL: 886-2-22699888 ext.27051 FAX: 886-2-22699816 Email: Eddy_Wang@foxlink.com

Request Letter Request for short term confidentiality data change IHDT6MU1 Date: September 28, 2011 Subject:

FCC ID:

Ref:

Original request confidential date: 02/25/2012 Applicant: Motorola Mobility, Inc. Dear Examiner, This is to request a FCC short-term confidentiality for change the date end of FCC ID: IHDT6MU1, the originally FCC granted on 09/16/2011. The reason we changed and filed under this application is:

Since we changed our policy for the marketing and request to change the short-term confidentiality end day to 2011/10/05. Please help to make this change. Best Regards, FCC Liaison Motorola Mobility, Inc. 8000 W. Sunrise Blvd.; Suite A Mail Stop 52-5JJ Plantation, FL 33322 E-mail: John.Lewczak@motorola.com

Hi, Daphne, TCB Q and A Please address following issues. Q#1:According to the block diagram, the micro USB is two way operation which may include data communication. If it is, then it should be considered as PC peripheral that FCC DOC or certification rule. Please address it as well. ANS:After checked with client , even the micro USB is two way operation,but it is only operated for the charge mode and without the data communication. So the PC peripheral that FCC DOC or certification is not considered. Best Regards, Lucy Tsai/UL CCS Page 1