PRELIMINARY DRAFT Motorola Satellite Series 9522 L-Band Transceiver Fact Sheets
. SHEET 1 PRELIMINARY DRAFT Motorola Satellite Series 9522 L-Band Transceiver Fact Sheets 1 Product Overview The 9522 LBT is intended for incorporation into a final Iridium subscriber product that would supply power, provide an antenna, and provide user interface components such as a keypad, display, microphone, and speaker. If the final product supports a data mode, an RS232 data interface would also be included. Regulatory approval for FCC, Canada and CE will be provided for the 9522 LBT assuming an antenna with a gain of 3 dBi. This will allow the 9522 LBT to be integrated into a variety of subscriber products, as well as retrofitted into existing LBT-based subscriber products. These products, when integrated together will require Regulatory testing. The functional capabilities of the 9505 handset provide the baseline for the 9522 LBT, noting that user interface components must be added to the 9522 LBT in order to access such functionality. The ISU AT Command Reference and the Satellite Series 9505 Portable Telephone Users Guide provide information relevant to the 9522 LBTs functional capabilities. The following differences exist when comparing the functional capabilities of the 9522 LBT to the 9505 handset. The 9522 LBT is always powered externally and therefore has no battery metering. The 9522 LBT does not incorporate a vibrating call alert and therefore has no vibrate/ring control. The 9522 LBT incorporates an analog audio interface not present on the 9505 handset. 2 Standards Compliance The 9522 LBT has been designed to comply with the standards for Emissions Compliance, Electromagnetic Compatibility, Electromagnetic Safety, and AC Safety in the United States, Europe and Canada. Standards in other areas of the world are often the same. 2.1 FCC Compliance This device has been certified under 47 CFR Part 25 as FCC ID: IHDT6NJ1 and also complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Any changes or modifications, including the use of a non-standard antenna, not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. IMPORTANT: To comply with FCC RF exposure requirements, a minimum separation of 20 cm is required between the antenna and all persons. 2.2 CE Compliance This product, when marked with the CE symbol, complies with the European Community Council Directive for R&TTE, 99/5/EC, provided the installer/user adheres to the instructions detailed in the Interface specification. This product is in compliance with applicable ETSI standards. Compliance with the requirements of ETSI EN 301 489 requires the use of a shielded digital data interface cable. SHEET 2 PRELIMINARY DRAFT 3 Physical Specifications The 9522 LBT is depicted in Figure 1 below. Figure 1: Top View 3.1 Environmental The environmental specifications of the 9522 LBT are summarized in Table 1 below. Table 1: Environmental Specifications Parameter Operating Temperature Range Operating Humidity Range Storage Temperature Range Storage Humidity Range Value
-20C to +60C 85% RH
-40C to +85C 85% RH 3.2 Dimensions The overall dimensions of the 9522 LBT and its weight are summarized in Table 2 below. Dimensioned views of the 9522 LBT are shown in Figures 2-5 to follow. Table 2: Mechanical Dimensions Parameter Length (including antenna connector) Length (excluding antenna connector) Width Depth Weight (approximate) Value 216.1 mm (8.51") 196.4 mm (7.73") 82.6 mm (3.25") 39.0 mm (1.54") 610 g
. SHEET 3 PRELIMINARY DRAFT Figure 2: Side View Figure 3: Bottom View
. SHEET 4 PRELIMINARY DRAFT Figure 4: Antenna Connector End View Figure 5: Multi-Interface Connector End View 3.3 Interface Connectors The 9522 LBT incorporates three interface connectors. Multi-Interface Connector (located on the end of the 9522 LBT) Antenna Connector (located on the end of the 9522 LBT; opposite to the multi-interface connector) Subscriber Identity Module (SIM) Chip Connector (located beneath a cover plate atop the 9522 LBT)
. SHEET 5 PRELIMINARY DRAFT 3.3.1 Multi-Interface Connector The multi-interface connector is a 25 pin D-subminiature type that includes four interfaces. DC Power Control/Audio RS232 Data Analog Audio 3.3.2 Antenna Connector The 9522 LBT provides a single, 50 , TNC type antenna connector for both transmit and receive. 3.3.3 SIM Chip Connector An integrated SIM chip connector is provided on the 9522 LBT. This connector allows installation of the chip form of the SIM beneath a cover plate on the 9522 LBT housing. 4 Electrical Interfaces The subsections to follow contain interface information for the electrical interfaces of the 9522 LBT. 4.1 DC Power Interface 4.1.1 DC Power Interface Signal Descriptions The DC power interface is comprised of the DC power inputs and a control signal as summarized in Table 3 below. The EXT_B+ and GND inputs are used to supply DC power to the 9522 LBT. The EXT_ON_OFF control input is pulled to a GND level to toggle the 9522 LBT on and off. Table 3: Control/Audio Interface Signal Descriptions Signal Name EXT_B+
GND EXT_ON_OFF Power on/off control input Signal Description External 4.4 VDC input External GND input
. SHEET 6 PRELIMINARY DRAFT 4.1.2 DC Power Input Specifications The DC power requirements for the 9522 LBT are summarized in Table 4 below. Note that these requirements apply to DC power measured at the 9522 LBT multi-interface connector input. Table 4: DC Power Input Specifications Parameter Main Input Voltage - Range Main Input Voltage - Nominal Main Input Voltage - Ripple Peak Input Current (maximum) Main Input Active Power (average) Main Input Standby Power (average) Value
+4.0 VDC to +4.8 VDC 4.4 VDC 40 mVpp 2.5 A @ 4.4 VDC 2500 mW 210 mW 4.2 Control/Audio Interface 4.2.1 Control/Audio Interface Signal Descriptions The control/audio interface enables peripherals such as handsets and SIM card readers to be interfaced to the 9522 LBT. The interface utilizes a Motorola Proprietary full duplex communication buss not detailed in this fact sheet. Details can be made available after appropriate Non-disclosure Agreements and /or License Agreements are executed. 4.3 RS232 Data Interface 4.3.1 RS232 Data Signal Descriptions The RS232 data interface is comprised of eight standard RS232 data, control, and status signals plus a ground level signal reference. This interface allows a connected Data Terminal Equipment (DTE) to utilize the 9522 LBTs modem functionality via AT command control. 4.4 Analog Audio Interface 4.4.1 Analog Audio Interface Signal Descriptions The analog audio interface is comprised of the analog audio input and output signals, an enable input signal, and a ground level signal reference as summarized in Table 5 below. Table 5: Analog Audio Interface Signal Descriptions Signal Name MIC_AUD SPKR_AUD ANALOG_AUD_EN Analog audio enable input ANALOG_GND Signal Description Analog audio input Analog audio output Analog audio ground level signal reference
. SHEET 7 PRELIMINARY DRAFT 4.5 SIM Interface An integrated SIM chip connector is provided on the 9522 LBT. An external SIM card reader may also be interfaced as a peripheral to the 9522 LBT via the DSC bus of the control/audio interface. A SIM card in the external reader will take precedence over the SIM chip in the integrated connector when both are present. 4.6 RF Interface 4.6.1 RF Interface Specifications The RF interface requirements for the 9522 LBT are summarized in Table 6 below. Table 6: General RF Parameters Parameter Frequency Range Duplexing Method Oscillator Stability Input/Output Impedance Multiplexing Method Value 1616 MHz to 1626.5 MHz TDD (Time Domain Duplex) 1.5 ppm 50 TDMA/FDMA 4.6.2 Radio Characteristics The tables within this section contain radio characteristics of the 9522 LBT. Table 7: In-Band Characteristics Parameter Average Power during a transmit slot (max) Average Power during a frame (typical) Receiver Sensitivity at 50 (typical) Receiver Spurious Rejection at offsets > 1 MHz (typical) Value 7 W 0.6 W
-118.5 dBm 60 dB Table 8: Link Margin Configuration 9522 LBT with Motorola accessory antennas (Note 1) Cable Loss 2 dB (Note 2) Link Margin 13.1 dB (Note 3) Note 1: Other antenna options may become available Note 2: Cable losses should be minimized Note 3: Link Margin given for free space
. SHEET 8