all | frequencies |
|
|
exhibits | applications |
---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User Manual Part 1 | Users Manual | 2.09 MiB | ||||
1 |
|
User Manual Part 2 | Users Manual | 2.03 MiB | ||||
1 | Attestation Statements | |||||||
1 | Cover Letter(s) | |||||||
1 | External Photos | |||||||
1 | External Photos | |||||||
1 | External Photos | |||||||
1 | External Photos | |||||||
1 | ID Label/Location Info | |||||||
1 | Internal Photos | |||||||
1 | Internal Photos | |||||||
1 | Internal Photos | |||||||
1 | Internal Photos | |||||||
1 | RF Exposure Info | |||||||
1 | Operational Description | |||||||
1 | Cover Letter(s) | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos |
1 | User Manual Part 1 | Users Manual | 2.09 MiB |
User Guide SBG940 Wireless Cable Modem Gateway Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. THE UNIT MUST NOT BE EXPOSED TO DRIPPING OR SPLASHING. DO NOT PLACE OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, ON THE UNIT. CAUTION: TO PREVENT ELECTRIC SHOCK, THIS EQUIPMENT MAY REQUIRE A GROUNDING CONDUCTOR IN THE LINE CORD. CONNECT THE UNIT TO A GROUNDING TYPE AC WALL OUTLET USING THE POWER CORD SUPPLIED WITH THE UNIT. CAUTION: THIS PRODUCT WAS QUALIFIED UNDER TEST CONDITIONS THAT INCLUDED THE USE OF THE SUPPLIED CABLES BETWEEN SYSTEMS COMPONENTS. TO ENSURE REGULATORY AND SAFETY COMPLIANCE, USE ONLY THE PROVIDED POWER AND INTERFACE CABLES AND INSTALL THEM PROPERLY. CAUTION: DIFFERENT TYPES OF CORD SETS MAY BE USED FOR CONNECTIONS TO THE MAIN SUPPLY CIRCUIT. USE ONLY A MAIN LINE CORD THAT COMPLIES WITH ALL APPLICABLE PRODUCT SAFETY REQUIREMENTS OF THE COUNTRY OF USE. CAUTION: INSTALLATION OF THIS PRODUCT MUST BE IN ACCORDANCE WITH NATIONAL WIRING CODES AND CONFORM TO LOCAL REGULATIONS. CAUTION: DO NOT OPEN THE UNIT. DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE INSTALLATION AND TROUBLESHOOTING INSTRUCTIONS. REFER ALL SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION: CHANGES AND MODIFICATIONS NOT EXPRESSLY APPROVED BY MOTOROLA FOR COMPLIANCE COULD VOID USERS AUTHORITY TO OPERATE THE EQUIPMENT. When using this device, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:
Read all of the instructions listed here and/or in the user manual before you operate this equipment. Give particular attention to all safety precautions. Retain the instructions for future reference. This device must be installed and used in strict accordance with manufacturers instructions as described in the user documentation that comes with the product. Comply with all warning and caution statements in the instructions. Observe all warning and caution symbols that are affixed to this equipment. Comply with all instructions that accompany this equipment. Do not overload outlets or extension cords, as this can result in a risk of fire or electric shock. Overloaded AC outlets, extension cords, frayed power cords, damaged or cracked wire insulation, and broken plugs are dangerous. They may result in a shock or fire hazard. Route power supply cords so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cords where they are attached to plugs and convenience receptacles, and examine the point where they exit from the product. Place this equipment in a location that is close enough to an electrical outlet to accommodate the length of the power cord. Place unit to allow for easy access when disconnecting the power cord of the device from the AC wall outlet. Do not connect the plug into an extension cord, receptacle, other outlet unless the plug can be fully inserted with no part of the blades exposed. Place this equipment on a stable surface. Home Print X Exit ii SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Postpone cable modem installation until there is no risk of thunderstorm or lightning activity in the area. Avoid using this product during an electrical storm. There may be a risk of electric shock from lightning. For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet, and disconnect the cable system. This will prevent damage to the product due to lightning and power surges. It is recommended that the customer install an AC surge protector in the AC outlet to which this device is connected. This is to avoid damaging the equipment by local lightning strikes and other electrical surges. Do not cover the device, or block the airflow to the device with any other objects. Keep the device away from excessive heat and humidity and keep the device free from vibration and dust. Wipe the unit with a clean, dry cloth. Never use cleaning fluid or similar chemicals. Do not spray cleaners directly on the unit or use forced air to remove dust. Avoid damaging the cable modem with static by touching the coaxial cable when it is attached to the earth grounded coaxial cable TV wall outlet. Always first touch the coaxial cable connector on the cable modem when disconnecting or re-connecting USB or Ethernet cable from the cable modem or the users PC. Operate this product only from the type of power source indicated on the products marking label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in safe operating condition. Be sure that the outside cable system is grounded, so as to provide some protection against voltage surges and built-up static charges. Article 820-20 of the NEC (Section 54, Part I of the Canadian Electrical Code) provides guidelines for proper grounding and, in particular, specifies the CATV cable ground shall be connected in the grounding system of the building, as close to the point of cable entry as practical. Apparaten skall anslutas till jordat uttag nr den ansluts ett nverk. FCC Compliance Class B Digital Device This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Increase the separation between the equipment and receiver. Reorient or relocate the receiving antenna. Home Print X Exit iii SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB FCC Certification This product contains a radio transmitter and accordingly has been certified as compliant with 47 CFR Part 15 of the FCC Rules for intentional radiators. Products that contain a radio transmitter are labeled with FCC ID and the FCC logo. CAUTION: Exposure to Radio Frequency Radiation. To comply with the FCC RF exposure compliance requirements, the separation distance between the antenna and any persons body (including hands, wrists, feet and ankles) must be at least 20 cm (8 inches). Canada - Industry Canada (IC) The wireless radio of this device complies with RSS 210 and RSS 102 of Industry Canada. This Class B digital device complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. Only use the antenna(s) provided with this product or an antenna approved by Motorola. Regulatory, Safety, Software License, and Warranty Information Card This product is provided with a separate Regulatory, Safety, Software License, and Warranty Information card. If one is not provided with this product, please ask your service provider or point-of-purchase representative, as the case may be. THIS PRODUCT IS IN COMPLIANCE WITH ONE OR MORE OF THE STANDARDS LISTED ON THE REGULATORY, SAFETY, SOFTWARE LICENSE, AND WARRANTY INFORMATION CARD. NOT ALL STANDARDS APPLY TO ALL MODELS. NO WARRANTIES OF ANY KIND ARE PROVIDED BY MOTOROLA WITH RESPECT TO THIS PRODUCT, EXCEPT AS STATED ON THE REGULATORY, SAFETY, SOFTWARE LICENSE, AND WARRANTY INFORMATION CARD. MOTOROLAS WARRANTIES DO NOT APPLY TO PRODUCT THAT HAS BEEN REFURBISHED OR REISSUED BY YOUR SERVICE PROVIDER. Copyright 2004 by Motorola, Inc. All rights reserved. No part of this publication may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation or adaptation) without written permission from Motorola, Inc. Motorola reserves the right to revise this publication and to make changes in content from time to time without obligation on the part of Motorola to provide notification of such revision or change. Motorola provides this guide without warranty of any kind, either implied or expressed, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Motorola may make improvements or changes in the product(s) described in this manual at any time. MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. Microsoft, Windows, Windows Me, Windows NT, and Xbox are registered trademarks and Windows XP and Xbox Live are trademarks of Microsoft Corporation. Microsoft Windows screen shots are used by permission of Microsoft Corporation. Macintosh and AppleTalk are registered trademarks of Apple Computer, Inc. Iomega is a registered trademark of Iomega Corporation. Linux is a registered trademark of Linus Torvalds. Acrobat Reader is a registered trademark of Adobe Systems, Inc. Netscape and Navigator are registered trademarks of Netscape Communications Corporation. PlayStation is a registered trademark of Sony Computer Entertainment Inc. UNIX is a registered trademark of the Open Group in the United States and other countries. Wi-Fi is a registered trademark of the Wi-Fi Alliance. All other product or service names are the property of their respective owners. Home Print X Exit iv SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Contents Overview . 1 Easy Setup . 2 Network Connection Types . 2 Powerful Features in a Single Unit . 2 Sample Hybrid LAN . 3 Optional Accessories . 4 Front Panel . 5 Rear Panel . 6 Label on the Bottom of the SBG940 . 7 SBG940 LAN Choices . 7 Wireless LAN . 8 Wired Ethernet LAN . 9 USB Connection . 11 Security . 12 Firewall . 12 DMZ . 13 Port Triggering . 13 Wireless Security . 13 Port Forwarding . 14 Virtual Private Networks . 14 Related Documentation . 14 Installation. 15 Before You Begin . 15 Precautions . 16 Signing Up for Service . 16 Computer System Requirements . 17 Connecting the SBG940 to the Cable System . 18 Cabling the LAN . 18 Obtaining an IP Address for Ethernet . 19 Obtaining an IP Address in Windows 98, Windows 98 SE, or Windows Me . 19 Obtaining an IP Address in Windows 2000 or Windows XP . 19 Obtaining an IP Address on Macintosh or UNIX Systems . 19 Connecting a PC to the USB Port . 20 Wall Mounting . 21 Wall Mounting Template . 23 Basic Configuration . 24 Starting the SBG940 Setup Program . 25 Changing the Default Password . 27 Enabling Remote Access . 28 Getting Help . 29 Setting the Firewall Policy . 30 Firewall > POLICY advanced Page . 32 Firewall > ALERT basic Page . 34 Firewall > ALERT email Page . 35 Firewall > LOGS Page . 36 Gaming Configuration Guidelines . 37 Configuring the Firewall for Gaming . 37 Configuring Port Triggers . 37 Configuring a Gaming DMZ Host . 38 Configuring the Gateway . 39 Gateway > STATUS Page . 40 Gateway > WAN Page . 41 Gateway > LAN nat config Page . 43 Gateway > LAN dhcp server config Page . 44 Gateway > LAN dhcp leases Page . 45 Gateway > PORT FORWARDING status Page . 46 Gateway > PORT FORWARDING config Page . 47 Gateway > PORT TRIGGERS predefined Page . 48 Gateway > PORT TRIGGERS custom Page . 50 Gateway > LOG Page . 51 Configuring TCP/IP . 52 Configuring TCP/IP in Windows 95, Windows 98, or Windows Me . 52 Configuring TCP/IP in Windows 2000 . 55 Configuring TCP/IP in Windows XP . 59 Verifying the IP Address in Windows 95, Windows 98, or Windows Me . 63 Verifying the IP Address in Windows 2000 or Windows XP .64 Setting Up Your Wireless LAN. 66 Encrypting Wireless LAN Transmissions . 67 Configuring WPA on the SBG940 . 68 Configuring WEP on the SBG940 . 70 Restricting Wireless LAN Access . 72 Configuring the Wireless Network Name on the SBG940 . 73 Configuring a MAC Access Control List on the SBG940 .75 Configuring the Wireless Clients . 76 Configuring a Wireless Client for WPA . 77 Configuring a Wireless Client for WEP . 77 Configuring a Wireless Client with the Network Name (ESSID) . 77 Home Print X Exit v SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Wireless Pages in the SBG940 Setup Program . 78 Wireless > STATUS Page . 79 Wireless > NETWORK Page . 80 Wireless > SECURITY basic Page . 82 Wireless > SECURITY advanced Page . 83 Wireless > STATISTICS page . 84 Setting Up a USB Driver . 86 Setting Up a USB Driver in Windows 98 . 87 Setting Up a USB Driver in Windows 2000 . 91 Setting Up a USB Driver in Windows Me . 94 Setting Up a USB Driver in Windows XP . 95 Removing the USB Driver from Windows 98 or Windows Me . 96 Removing the USB Driver from Windows 2000 . 99 Removing the USB Driver from Windows XP . 102 Troubleshooting . 107 Front-Panel Lights and Error Conditions . 108 Contact Us . 109 Frequently-Asked Questions . 110 Specifications . 112 Glossary. 114 Software License . 132 Home Print X Exit vi SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Overview Thank you for purchasing a Motorola SURFboard Wireless Cable Modem Gateway SBG940 for your home, home office, or small business/enterprise. Applications where the SURFboard Gateway (SBG) is especially useful include:
Households having multiple computers requiring connection to the Internet and each other Small businesses or home offices requiring fast, affordable, and secure Internet access Internet gamers desiring easier setup for:
Programs such as DirectX 7 or DirectX 8 Sites such as MSN Games by Zone.com or Battle.net Video conferencing The features and physical appearance of your SBG940 may differ slightly from the picture. A home network enables you to share information between two or more computers. You can connect your home network to the Internet through the cable TV system. The SBG940 is the central connection point between your computers and the Internet. It directs (routes) information between the computers connected to your home network. A built-in cable modem transmits information between your home network and the Internet. An SBG940:
Combines four separate products a DOCSIS cable modem, IEEE 802.11g wireless access point, Ethernet 10/100Base-T connections, and firewall into one compact unit Enables you to create a custom network sharing a single broadband connection, files, and peripherals, with or without wires Has an advanced firewall for enhanced network security for wired and wireless users Provides easy setup This product is subject to change. Not all features described in this guide are available on all SBG940 models. For the most recent documentation, visit the Cable Modems and Gateways page on the Motorola Broadband website http://broadband.motorola.com/. Home Print X Exit 1 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Easy Setup It is much easier to configure a local area network (LAN) using an SBG940 than using traditional networking equipment:
The Setup Program provides a graphical user interface (GUI) for easy configuration of necessary wireless, Ethernet, router, DHCP, and security settings. For information about using the Setup Program, see Basic Configuration. For basic operation, most default settings require no modification. Network Connection Types The SBG940 provides different network connection types for your computers to exchange data. The connection between your computers and the SBG940 may be with a wireless or a wired connection or a combination of the two. Your network can use one or any combination of all the following network connections:
Wireless LAN (IEEE 802.11g that also supports IEEE 802.11b wireless clients) Ethernet local area network (LAN) Universal Serial Bus (USB) Powerful Features in a Single Unit An SBG940 combines high-speed Internet access, networking, and computer security for a home or small-office LAN. An SBG940 provides:
An integrated high-speed SURFboard cable modem for continuous broadband access to the Internet and other online services, with much faster data transfer than traditional dial-up or ISDN modems A single broadband connection for up to 253 computers to surf the web; all computers on the LAN communicate as if they were connected to the same physical network An IEEE 802.11g wireless access point to enable laptop users to remain connected while moving around the home or small office or to connect desktop computers without installing network wiring. Depending on distance, wireless connection speeds can match that of Ethernet. A USB connection for a single PC Four 10/100Base-T Ethernet uplink ports supporting half- or full-duplex connections and Auto-MDIX Routing for a wireless LAN (WLAN) or a wired Ethernet LAN; you can connect more than four computers using hubs and/or switches A built-in DHCP server to easily configure a combined wired and/or wireless Class C private LAN An advanced firewall supporting stateful-inspection, intrusion detection, DMZ, denial-of-service attack prevention, and Network Address Translation (NAT) Virtual private network (VPN) pass-through operation supporting IPSec, PPTP, or L2TP to securely connect remote computers over the Internet Port Forwarding to configure ports to run applications having special network requirements Home Print X Exit 2 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB A PDA on a wireless connection Sample Hybrid LAN The sample LAN illustrated on this page contains the following devices, all protected by the SBG940 firewall Clockwise from top-right, the devices are:
One desktop Apple Macintosh computer on a wireless connection One desktop PC on a wireless connection using a Motorola Wireless PCI Adapter A laptop PC on a wireless connection using a Motorola Wireless Notebook Adapter One PC connected to the USB port One computer connected directly to Ethernet port two Three computers connected to Ethernet port one using a hub or switch Internet High-speed HFC cable network Wireless Firewall To AC power SBG940 USB Ethernet Hub or switch Home Print X Exit 3 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Optional Accessories All networks are composed of multiple devices. The SBG940 works with any IEEE 802.11g or IEEE 802.11b compliant client product. Motorola supplies a range of accessories for use with the SBG940. Some examples are:
Wireless Ethernet Bridge WE800G Ethernet Broadband Router BR700 Wireless Notebook Adapter WN825G Wireless USB Adapter WU830G Wireless PCI Adapter WPCI810G For up-to-date information about accessories and home networking options, including product documentation, visit the Motorola Home Networking page http://broadband.motorola.com/consumers/home_networking.asp. Home Print X Exit 4 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Front Panel The front panel provides indicator lights. The display is dark unless there is a connection or activity on an interface:
1 2 3 4 5 6 7 8 Key Light Flashing On 1 2 3 4 5 6 7 8 Never flashes The AC power is connected properly DS US Scanning for a receive (downstream) channel connection Scanning for a send (upstream) channel connection ONLINE Scanning for a network connection Transmitting or receiving data over the Internet Ethernet activity on the port (1 to 4) The downstream channel is connected The upstream channel is connected The startup process is complete and the SBG940 is online Is never lit solid There is a connection to the port (1 to 4):
Green for 100Base-T Yellow for 10Base-T USB activity Lights green if there is a proper USB connection Wireless activity The wireless interface is on (Enable Wireless Interface is selected on the Wireless > NETWORK Page in the SBG940 Setup Program) Home Print X Exit 5 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Rear Panel The rear panel provides cabling connectors, status lights, and the power receptacle:
1 2 3 4 5 6 7 Key Item Description 1 2 3 4 5 6 7 An adjustable, but non-removable antenna. Do not attempt to force this antenna off the unit. Use any Ethernet port to connect an Ethernet LAN cable with RJ-45 connectors to an Ethernet-equipped computer, hub, bridge, switch or Xbox or PlayStation 2 gaming console. For Windows only, use the USB port for Connecting a PC to the USB Port. You cannot connect the SBG940 USB port to a Macintosh or UNIX computer. RESET If you experience a problem, you can push this recessed button to restart the SBG940 (see Troubleshooting). To reset all values to their defaults, hold down the button for more than five seconds. Resetting may take 5 to 30 minutes because the SBG940 must find and lock on the appropriate communications channels. Use the cable connector to connect to the coaxial cable outlet. Removable, adjustable antenna. If necessary, contact your cable provider about obtaining an optional Motorola wireless high gain antenna to increase WLAN performance and coverage. Use the AC connector to connect to the AC power outlet. Home Print X Exit 6 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Label on the Bottom of the SBG940 To receive data service, you need to provide the MAC address marked HFC MAC ID to your cable provider:
HFC MAC ID USB Connection SBG940 LAN Choices The SBG940 enables you to connect up to 253 client computers on a combination of:
Wireless LAN Wired Ethernet LAN Each computer needs appropriate network adapter hardware and driver software. The clients on the Ethernet, wireless, or USB interfaces can share:
Wireless and wired network connections use Windows networking to share files and peripheral devices such as printers, CD-ROM drives, floppy disk drives, and Iomega Zip Drives. Internet access with a single cable provider account, subject to cable provider terms and conditions Files, printers, storage devices, multi-user software applications, games, and video conferencing Home Print X Exit 7 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Wireless LAN Wireless communication occurs over radio waves rather than a wire. Like a cordless telephone, a WLAN uses radio signals instead of wires to exchange data. A wireless network eliminates the need for expensive and intrusive wiring to connect computers throughout the home or office. Mobile users can remain connected to the network even when carrying their laptop to different locations in the home or office. Each computer on a WLAN requires a wireless adapter shown in Optional Accessories:
Laptop PCs Desktop PCs Use a Motorola Wireless PCI Adapter, Wireless USB Adapter, or compatible product in the PCI slot or Use a Motorola Wireless Notebook Adapter or compatible product in the PCMCIA slot. USB port, respectively. Sample wireless network connections To AC power SBG940 Computer with wired connection used to run SBG940 Setup Program To set up the SBG940, on a computer wired to the SBG940 over Ethernet or USB, perform the procedures in Setting Up Your Wireless LAN. Do not attempt to configure the SBG940 over a wireless connection. Your maximum wireless operation distance depends on the type of materials through which the signal must pass and the location of your antennas and clients (stations). Motorola cannot guarantee wireless operation for all supported distances in all environments. An optional Motorola high gain antenna can improve wireless performance. For information about available optional antennas for your SBG940, contact your cable provider. Home Print X Exit 8 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Wired Ethernet LAN Each computer on the 10/100Base-T Ethernet LAN requires an Ethernet network interface card (NIC) and driver software installed. Because the SBG940 Ethernet port supports auto-MDIX, you can use straight-through or cross-over cable to connect a hub, switch, or computer. Use category 5 cabling for all Ethernet connections. The physical wiring arrangement has no connection to the logical network allocation of IP addresses. Sample Ethernet to computer connection Coaxial cable To AC power SBG940 Category 5 Ethernet cable Home Print X Exit 9 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Connect a hub or switch to any Ethernet port on the SBG940 Use Ethernet hubs, switches, or routers to connect up to 253 computers to the SBG940 A wired Ethernet LAN with more than four computers requires one or more hubs, switches, or routers. You can:
The following illustration is an example of an Ethernet LAN you can set up using the SBG940. Cable the LAN in an appropriate manner for the site. A complete discussion of Ethernet cabling is beyond the scope of this document. Sample Ethernet connection to hubs or switches To AC power SBG940 Add additional hubs or switches for further expansion Home Print X Exit 10 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB USB Connection You can connect a single PC running Windows 98, Windows XP, Windows Me, or Windows 2000 to the SBG940 USB V1.1 port. For cabling instructions, see Connecting a PC to the USB Port. Caution!
Before plugging in the USB cable, be sure the SBG940 Installation CD-ROM is inserted in the PC CD-ROM drive. Sample USB connection SBG940 To AC power Home Print X Exit 11 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB A firewall to protect the SBG940 LAN from undesired attacks over the Internet Security The SBG940 provides:
Network Address Translation (NAT) provides some security because the IP addresses of SBG940 LAN computers are not visible on the Internet. This diagram does not necessarily correspond to the network cabling. A full discussion of network security is beyond the scope of this document. For wireless transmissions, data encryption and network access control SBG940 security measures shown in a logical network diagram Internet SBG940 Firewall DMZ computer Wireless Security:
Encryption, MAC access control, or closed network operation Computer Computer Computer Laptop PDA Wired Ethernet LAN Wireless LAN Firewall The SBG940 firewall protects the SBG940 LAN from undesired attacks and other intrusions from the Internet. It provides an advanced integrated stateful-inspection firewall supporting intrusion detection, session tracking, and denial-of-service attack prevention. The firewall:
Maintains state data for every TCP/IP session on the OSI network and transport layers Monitors all incoming and outgoing packets, applies the firewall policy to each one, and screens for improper packets and intrusion attempts Provides comprehensive logging for all:
User authentications Rejected internal and external connection requests Session creation and termination Outside attacks (intrusion detection) You can configure the firewall filters to set rules for port usage. For information about choosing a predefined firewall policy template, see Setting the Firewall Policy. Home Print X Exit 12 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB DMZ A de-militarized zone (DMZ) is one or more computers logically located outside the firewall between an SBG940 LAN and the Internet. A DMZ prevents direct access by outside users to private data. For example, you can set up a web server on a DMZ computer to enable outside users to access your website without exposing confidential data on your network. A DMZ can also be useful to play interactive games that may have a problem running through a firewall. You can leave a computer used for gaming only exposed to the Internet while protecting the rest of your network. For more information, see Gaming Configuration Guidelines. Port Triggering When you run an application that accesses the Internet, it typically initiates communications with a computer on the Internet. For some applications, especially gaming, the computer on the Internet also initiates communications with your computer. Because NAT does not normally allow these incoming connections:
If needed, you can configure additional port triggers on the Gateway > PORT TRIGGERS custom Page. The SBG940 has preconfigured port triggers for common applications. Wireless Security Because WLAN data is transmitted using radio signals, it may be possible an unauthorized person to access your WLAN unless you prevent them from doing so. To prevent unauthorized eavesdropping of data transmitted over your LAN, you must enable wireless security. The default SBG940 settings neither provide security for transmitted data nor protect network data from unauthorized intrusions. The SBG940 provides the following wireless security measures, which are described in Setting Up Your Wireless LAN:
To prevent unauthorized eavesdropping, you must encrypt data transmitted over the wireless interface using one of:
If all of your wireless clients support Wi-Fi Protected Access (WPA) encryption, we recommend using WPA (see Configuring WPA on the SBG940 and Configuring a Wireless Client for WPA). Otherwise, configure a Wired Equivalency Privacy (WEP) key on the SBG940 and each WLAN client
(see Configuring WEP on the SBG940 and Configuring a Wireless Client for WEP). To protect LAN data from unauthorized intrusions, you can restrict WLAN access to computers having one or both of:
Known MAC addresses (see Configuring a MAC Access Control List on the SBG940) The same unique network name (ESSID) as the SBG940 (see Configuring the Wireless Network Name on the SBG940 and Configuring a Wireless Client with the Network Name (ESSID)) Restricting access to computers having the same network name is also called disabling ESSID broadcasting or enabling closed network operation. Home Print X Exit 13 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Port Forwarding The SBG940 opens logical data ports when a computer on its LAN sends data, such as e-mail messages or web data, to the Internet. A logical data port is different from a physical port, such as an Ethernet port. Data from a protocol must go through certain data ports. Some applications, such as games and videoconferencing, require multiple data ports. If you enable NAT, this can cause problems because NAT assumes that data sent through one port will return to the same port. You may need to configure port forwarding to run applications with special requirements. To configure port forwarding, you must specify an inbound (source) port or range of ports. The inbound port opens only when data is sent to the inbound port and closes again after a specified time elapses with no data sent to it. You can configure up to 32 port forwarding entries using the Gateway > PORT FORWARDING config Page. Virtual Private Networks The SBG940 supports multiple tunnel VPN pass-through operation to securely connect remote computers over the Internet. The SBG940:
Is compatible with Point to Point Tunneling Protocol (PPTP) and Layer 2 Tunneling Protocol (L2TP) Is fully interoperable with any IPSec client or gateway and ANX certified IPSec stacks Related Documentation The SBG940 Quick Installation Guide also provides information about using the SBG940. For information about and documentation for Motorola home-networking products, visit the Motorola Home Networking page http://broadband.motorola.com/consumers/home_networking.asp. Home Print X Exit 14 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Installation Configuration: Basic Gateway TCP/IP Wireless USB Before You Begin Precautions Signing Up for Service Computer System Requirements Connecting the SBG940 to the Cable System Cabling the LAN The following subsections provide information about installing the SBG940 hardware:
Obtaining an IP Address for Ethernet Wall Mounting For information about WLAN setup, see Setting Up Your Wireless LAN. Connecting a PC to the USB Port Before You Begin Before you begin the installation, check that you received the following items with your SBG940:
Item Description Power cord 10/100Base-T Ethernet cable USB cable SBG940 Installation CD-ROM Connects the SBG940 to the AC electrical outlet Connects to the Ethernet port Connects to the USB port Contains this User Guide and USB drivers You will need 75-ohm coaxial cable with F-type connectors to connect the SBG940 to the nearest cable outlet. If a TV is connected to the cable outlet, you may need a 5 to 900 MHz RF splitter and two additional coaxial cables to use both the TV and the SBG940. Determine the connection types you will make to the SBG940. Check that you have the required cables, adapters, and adapter software. You may need:
Wireless LAN Wireless adapter and driver software for each computer having a wireless connection (see Optional Accessories) Wired Ethernet LAN Ethernet cables and network interface cards (NICs) with accompanying installation software To connect more than four computers to the SBG940, one or more Ethernet hubs or switches USB A USB cable and the SBG940 Installation CD-ROM containing the software for USB installation Coaxial cable, RF splitters, hubs, and switches are available at consumer electronic stores. Home Print X Exit 15 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Precautions Postpone SBG940 installation until there is no risk of thunderstorm or lightning activity in the area. To avoid damaging the SBG940 or computers with static electricity:
Always make the wall connection first. Before you connect or disconnect the USB or Ethernet cables, always touch the coaxial cable connector on the SBG940. To avoid potential shock, always unplug the power cord from the wall outlet or other power source before disconnecting it from the SBG940 rear panel. To prevent overheating the SBG940, do not block the ventilation holes on the sides of the unit. Do not open the unit. Refer all service to your cable provider. Wipe the unit with a clean, dry cloth. Never use cleaning fluid or similar chemicals. Do not spray cleaners directly on the unit or use forced air to remove dust. Signing Up for Service You must sign up with a cable provider to access the Internet and other online services. To activate your service, call your local cable provider. You need to provide the MAC address marked HFC MAC ID printed on the Label on the Bottom of the SBG940. You can record it in the SBG940 Quick Installation Guide. You should ask your cable provider the following questions:
When can I begin to use my SBG940?
Do I need a user name or password to access the Internet or use e-mail?
Are there any files I need to download after I am connected?
Do you have any special system requirements?
Home Print X Exit 16 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Computer System Requirements You can connect Microsoft Windows, Macintosh, UNIX, or Linux computers equipped as follows to the SBG940 LAN:
One of the following:
Ethernet Wireless 10Base-T or 10/100Base-T Ethernet adapter with proper NIC driver software installed. Any IEEE 802.11g or IEEE 802.11b device. For information about the Motorola WN825G Wireless Card (PCMCIA type II 3.3 V slot) or WPCI810G Wireless Adapter, see Optional Accessories. PC with Pentium class or better processor Windows 98, Windows 98 SE, Windows Me, Windows 2000, Windows XPTM, Windows NT, Macintosh, or Linux operating system with operating system CD-ROM available 10 MB available hard disk space Minimum 16 MB RAM recommended You can use any web browser such as Microsoft Internet Explorer or Netscape Navigator with the SBG940. You can use the USB connection with any PC running Windows 98, Windows 2000, Windows Me, or Windows XP that has a USB interface. The USB connection requires special USB driver software that is supplied on the SBG940 Installation CD-ROM. You can upgrade your USB drivers from the Motorola Downloads page http://broadband.motorola.com/noflash/usb_drivers.asp. Home Print X Exit 17 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Connecting the SBG940 to the Cable System 1 Be sure the computer is on and the SBG940 is unplugged. 2 Connect one end of the coaxial cable to the cable outlet or splitter. 3 Connect the other end of the coaxial cable to the cable connector on the SBG940. 4 5 6 Hand-tighten the connectors to avoid damaging them. Insert the SBG940 Installation CD-ROM into the CD-ROM drive. Plug the power cord into the power connector on the SBG940. Plug the power cord into the electrical outlet. This turns the SBG940 on. You do not need to unplug it when not in use. The first time you plug in the SBG940, allow 5 to 30 minutes to find and lock on the appropriate communications channels. Step 2 To AC power
(steps 5 to 6) Step 3 7 Check that the lights on the front panel cycle through this sequence:
Turns on when AC power is connected to the SBG940. Indicates that the power is connected properly. DS US Flashes while scanning for the downstream receive channel. Changes to solid green when the receive channel is locked. Flashes while scanning for the upstream send channel. Changes to solid green when the send channel is locked. ONLINE Flashes during SBG940 registration and configuration. Changes to solid green when the SBG940 is registered. Flashes when the SBG940 is transmitting or receiving data over the Internet. Cabling the LAN After connecting to the cable system, you can connect your wired Ethernet LAN. Some samples are shown in Wired Ethernet LAN. On each networked computer, you must install proper drivers for the Ethernet NIC. Detailed information about network cabling is beyond the scope of this document. Home Print X Exit 18 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Obtaining an IP Address for Ethernet Obtaining an IP Address in Windows 98, Windows 98 SE, or Windows Me You must do the following on each Ethernet client PC running Windows 98, Windows 98 SE, or Windows Me:
1 On the Windows Desktop, click Start. 2 3 Select Run. The Run window is displayed. Type winipcfg.exe and click OK. The IP Configuration window is displayed:
4 Click the Renew button to obtain an IP address for the PC from the DHCP server on the SBG940. Obtaining an IP Address in Windows 2000 or Windows XP You must do the following on each Ethernet client PC running Windows 2000 or Windows XP:
1 On the Windows Desktop, click Start. 2 3 4 Select Run. The Run window is displayed. Type cmd and click OK to display a command prompt window. Type ipconfig /renew and press ENTER to obtain an IP address for the PC from the DHCP server on the SBG940. Type exit and press ENTER to return to Windows. 5 Obtaining an IP Address on Macintosh or UNIX Systems Follow the instructions in your user manual. Home Print X Exit 19 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Connecting a PC to the USB Port You can connect a single PC running Windows 98, Windows XP, Windows Me, or Windows 2000 to the SBG940 USB port. Caution!
Before plugging in the USB cable, be sure the SBG940 Installation CD-ROM is inserted in the PC CD-ROM drive. Insert the SBG940 Installation CD-ROM in the CD-ROM drive. To connect a PC to the USB port:
1 2 3 Connect the USB cable to the USB port on the SBG940 Rear Panel. 4 Connect the other end to the USB port on the computer. Install the USB driver following the appropriate procedure for Setting Up a USB Driver. Step 3 To AC power Step 1 Step 4 Home Print X Exit 20 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Wall Mounting If you mount the unit on the wall, you must:
Locate the unit as specified by the local or national codes governing residential or business cable TV and communications services. Follow all local standards for installing a network interface unit/network interface device (NIU/NID). If possible, mount the unit to concrete, masonry, a wooden stud, or other very solid wall material. Use anchors if necessary; for example, if you must mount the unit on drywall. To mount your SBG940 on the wall:
1 Print the Wall Mounting Template on page 23. Go to page 23 and click the Print icon or choose Print from the File menu to display the Print dialog box.
(The following image is from Adobe Acrobat Reader version 4.0 running on Windows 2000; there may be slight differences in your version.) Select this to print page 23 only. Be sure this is not selected. Be sure you print the template at 100% scale. Be sure Fit to page is not selected. To print the template only, select Current page as the Print Range. Click the OK button to print the template. 2 Measure the printed template with a ruler to ensure that it is the correct size. 3 Use a center punch to mark the center of the holes. 4 On the wall, locate the marks for the mounting holes. Caution!
Before drilling holes, check the structure for potential damage to water, gas, or electric lines. 5 Drill the holes to a depth of at least 11/2 inches (3.8 cm). Home Print X Exit 21 SBG940 User Guide 6 Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB If necessary, seat an anchor in each hole. Use M5 x 38 mm (#10-16 x 11/2 inch) screws with a flat underside and maximum screw head diameter of 10.5 mm to mount the SBG940. 7 Using a screwdriver, turn each screw until part of it protrudes from the wall, as shown:
There must be .16 inches (4.0 mm) between the wall and the underside of the screw head. The maximum distance from the wall to the top of the screw head is 7.6 mm (.3 in). 3 inches (7.6 mm) maximum
.4 inches (10.5 mm) maximum
.16 inches (4.0 mm) 8 9 Place the SBG940 so the keyholes on the back of the unit are aligned above the mounting screws. Be sure you do not damage the antennas. Slide the SBG940 down until it stops against the top of the keyhole opening. Home Print X Exit 22 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Wall Mounting Template You can print this page to use as a wall mounting template. Be sure you print it at 100% scale. In Acrobat Reader, be sure that Fit To Page is not selected in the Print dialog box. Measure the printed template with a ruler to ensure that it is the correct size. m c 4 2 7 1
. n i 9 7 6
. Home Print X Exit 23 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Basic Configuration Setting the Firewall Policy Changing the Default Password Starting the SBG940 Setup Program The following sections provide information about basic SBG940 configuration:
Getting Help Gaming Configuration Guidelines For more advanced configuration information, see Configuring TCP/IP, Setting Up Your Wireless LAN, or Setting Up a USB Driver. For normal operation, you do not need to change most default settings. The following caution statements summarize the issues you must be aware of:
Caution!
To prevent unauthorized configuration, change the default password immediately when you first configure the SBG940. See Changing the Default Password. Firewalls are not foolproof. Choose the most secure firewall policy you can. See Setting the Firewall Policy. If you are using a wired LAN only and have no wireless clients, be sure you disable the wireless interface by turning off Enable Wireless Interface on the Wireless > NETWORK Page. For a wireless LAN only, be sure you follow the instructions in Setting Up Your Wireless LAN. Home Print X Exit 24 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Starting the SBG940 Setup Program 1 On a computer wired to the SBG940 over Ethernet or USB, open a web browser. Do not attempt to configure 2 the SBG940 over a wireless connection. In the Address or Location field, type http://192.168.100.1 or http://192.168.0.1 and press ENTER to display the Log In window:
3 4 In the User ID field, type the User Name; the default is admin (this field is case sensitive). In the Password field, type the Password; the default is motorola (this field is case sensitive). Home Print X Exit 25 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 5 Click Log In to display the SBG940 user configuration and status windows:
Click To Perform Configure and monitor the cable system connection. Cable Gateway Configure and monitor the gateway preferences (see Configuring the Gateway). Wireless Configure and monitor the wireless interface (see Setting Up Your Wireless LAN). Firewall Admin Info Reboot Changing the Default Password. Display information about the SBG940 Setup Program. Restart the SBG940. It is the same as pressing the reset button on the rear panel for less than five seconds. Configure and monitor the firewall (see Setting the Firewall Policy). Log Out Log out of the SBG940. If you have difficulty starting the SBG940 Setup Program, see Troubleshooting for information. Router is a configuration option that may appear on your window but may not be supported. For some settings, after you edit the field and click Apply, you are warned that you must reboot for your change to take effect. Rebooting takes 10 to 15 seconds. After rebooting, you must log in again. Home Print X Exit 26 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Changing the Default Password Caution!
To prevent unauthorized configuration, change the default password immediately when you first configure the Motorola SURFboard Wireless Cable Modem Gateway. To change the default password:
1 On the SBG940 Setup Program left panel, click Admin to display the ADMIN basic page:
2 In the Old Password field, type the old password. The default password is motorola (this field is case sensitive). In the New Password field, type the new password. In the Verify Password field, type the new password again. 3 4 5 Click Apply to apply your changes. Home Print X Exit 27 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Enabling Remote Access You can enable remote access to the SBG940 over the Internet. You must know the userid, password, and public IP address assigned to your SBG940 to run the Setup Program over the Internet. Remote access is provided using a web browser on the remote client and connecting to the SBG940 web server. To enable remote access to the SBG940:
1 On the SBG940 Setup Program left panel, click Admin to display the ADMIN basic page. 2 Click advanced to display the ADMIN advanced page. 3 Click the box next to Enable remote access to enable it. 4 Click Apply to apply your change. Home Print X Exit 28 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Getting Help To get help on any underlined item or field, click the text. For example, if you click a field or the help button on the ADMIN basic page, the following help is displayed:
This button also displays help for the window. You can scroll to browse the help or click another item to display help for that item. Home Print X Exit 29 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Setting the Firewall Policy The SBG940 firewall protects the SBG940 LAN from undesired attacks and other intrusions from the Internet. This section describes using the Firewall > POLICY basic page to choose one of the predefined firewall policy templates provided with the SBG940. Caution!
Firewalls are not foolproof. Choose the most secure firewall policy you can. To enable easy network setup, the default firewall policy is None, which provides no security. To select a predefined policy for all packets processed by the SBG940 firewall:
1 On the SBG940 Setup Program left panel, click Firewall. 2 Click POLICY. 3 Click basic to display the predefined firewall policy templates:
4 Select the most secure firewall policy you can:
The safest predefined firewall policy template, providing the highest security. We recommend this setting. High Medium A predefined firewall policy template providing a common configuration having modest risk. Low Custom You may need to create a custom firewall policy on the Firewall > POLICY advanced Page. Do not A predefined firewall policy template providing minimum security, with a higher risk of intrusions. create a custom policy unless you have the necessary expertise and the need to do so. None Disables the firewall. To enable easy network setup, it is the default. After you set up your network, use High, Medium, or Low to improve your security. Home Print X Exit 30 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 5 Click Apply to apply your changes. After you edit some fields and click Apply, you are warned that you must reboot for your change to take effect. Rebooting takes 10 to 15 seconds. After rebooting, you must log in again. If you have the need, you can:
View the rules for the High, Medium, or Low predefined policy templates or create a custom policy on the Firewall > POLICY advanced Page View the firewall logs on the Firewall > LOGS Page Configure a firewall alert on Firewall > ALERT basic Page and Firewall > ALERT email Page For information about how the firewall can affect gaming, see Gaming Configuration Guidelines. The predefined policies provide outbound Internet access for computers on the SBG940 LAN. The SBG940 firewall uses stateful inspection to allow inbound responses when there already is an outbound session running corresponding to the data flow. For example, if you use a web browser, outbound HTTP connections are permitted on port 80. Inbound responses from the Internet are allowed because an outbound session is established. When required, you can configure the SBG940 firewall to allow inbound packets without first establishing an outbound session. You also need to configure a port forwarding entry on the Gateway > PORT FORWARDING config Page or a DMZ client on the Gateway > LAN nat config Page. Home Print X Exit 31 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Firewall > POLICY advanced Page Do not create a custom firewall policy unless you have the necessary expertise and the need to do so. Instead, select one of the predefined policy templates as described in Setting the Firewall Policy. To create a custom firewall policy, first select Custom and click Apply on the Firewall > POLICY basic Page. Then use this page to configure a custom firewall policy:
To base the custom policy on a predefined firewall policy template, choose High, Medium, or Low in the Policy Template field and click Apply Policy Template. Home Print X Exit 32 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB
. Firewall > POLICY advanced page fields Field Description NEW FILTER ENTRY Use these fields to set up one or more custom firewall filters, if you have the necessary expertise. Port ID Enable Allowed Protocol Port Range (From:To) Protocol Number Allow Inbound Allow Outbound Type the protocol being filtered. Select this box to enable firewall policy filtering for the port. Select the allowed protocols from the drop-down list. Sets the port range, which must contain all ports required by the protocol. Sets the protocol number of the IP packets to allow. Enables you to specify the port(s) on which inbound packets can pass through the firewall from the Internet to your LAN. Enables you to specify the port(s) on which outbound packets can pass through the firewall from your LAN to the Internet. Stateful inspection ensures appropriate responses for outbound sessions. Add Click to add the new filter. It is displayed on the FIREWALL POLICY table. FIREWALL POLICY Table Lists your custom firewall filters. Enable Delete Apply FIREWALL POLICY TEMPLATE Policy Template Select this box to enable firewall policy filtering for the port. Select the Delete box to delete the filter. Click to apply your changes. You can use this drop-down list to select a predefined policy template on which to base your custom template High, Medium, or Low. These templates are described in Setting the Firewall Policy Apply Policy Template Click to apply the selected Policy Template and cancel any customizations. Home Print X Exit 33 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Firewall > ALERT basic Page You can use this page to set the alert mechanism for firewall intrusion detection events. Firewall > ALERT basic page fields Field or Button Description Intrusion Detection Select Email to be alerted through SMTP e-mail. An SMTP server that does not require any authentication such as a user name or password must be present to receive the e-mail. Apply Click to apply your changes. Home Print X Exit 34 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Firewall > ALERT email Page You can use this page to configure the e-mail alert parameters:
Firewall > ALERT email page fields Field or Button Description E-mail Server IP Address Sets the e-mail server IP address in dotted-decimal format. E-mail Server Port E-mail Sender E-mail Recipient List Apply Sets the sender e-mail address. Sets the list of e-mail addresses that receive alerts from the SBG940 firewall. Click to apply your changes. Sets the e-mail server port number. Home Print X Exit 35 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Firewall > LOGS Page You can use this page to set which firewall events are logged. Firewall > LOGS page fields Field or Button Description Enable Session Log Enable Blocking Log Select this box to log every data session from the private LAN that was authorized by the SBG940 firewall. Usually, the session log displays a history of normal data traffic. It also lists the start of sessions the firewall terminated because:
The policy was changed They were eventually determined to be an intrusion or attack To display the session log, click session. Select this box to log inbound and outbound packets that the SBG940 firewall:
Does not allow to pass because they use protocols and/or ports not explicitly allowed by the active policy Determines to be invalid because of a session or reassembly timeout To display the blocking log, click blocking. Enable Intrusion Log Select this box to log attacks using common network intrusion tactics that the SBG940 firewall detects and stops. To display the intrusion log, click intrusion. Apply Click to apply your changes. If you enable the firewall, the blacklist log is always generated. Any IP address the firewall determines to have breached the active policy is added to the blacklist log. To view the blacklist log, click blacklist. The firewall blocks all traffic to and from a blacklisted IP address for 24 hours or until you reboot the SBG940 or manually clear the blacklist by clicking Clear on the Firewall > LOGS blacklist page. Home Print X Exit 36 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Gaming Configuration Guidelines The following subsections provide information about configuring the SBG940 firewall and DMZ for gaming. Configuring the Firewall for Gaming By default, the SBG940 firewall is disabled. If, as recommended, you enable the firewall, refer to the games documentation to ensure that the necessary ports are open for use by that game. The pre-defined SBG940 firewall policies affect Xbox LiveTM as follows:
Low Medium or high To enable Xbox Live traffic to pass, you must configure:
Xbox Live data can pass through the firewall. No user action is required. Choose Custom on the Firewall > POLICY basic Page UDP 88:88 and UDP/TCP 3074:3074 on the Firewall > POLICY advanced Page DirectX 7 and DirectX 8 Configuring Port Triggers Because the SBG940 has pre-defined port triggers for games using any of the following applications, no user action is required to enable them:
MSN Games by Zone.com For a list of games supported by Battle.net, visit http://www.battle.net. You may need to create custom port triggers to enable other games to operate properly. If you set custom port triggers and enable the firewall, you must customize the firewall to allow traffic through those ports. To create custom port triggers, use the Gateway > PORT TRIGGERS custom Page. Battle.net Home Print X Exit 37 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Configuring a Gaming DMZ Host Caution!
The gaming DMZ host is not protected by the firewall. It is open to communication or hacking from any computer on the Internet. Consider carefully before configuring a device to be in the DMZ. The use of random ports The forwarding of unsolicited traffic Some games and game devices require one of:
For example, to connect a PlayStation 2 for PS2 online gaming, designate it as the gaming DMZ host because the ports required vary from game to game. For these games, we recommend configuring the gaming computer or device as a gaming DMZ device. To configure a gaming DMZ device, on the Gateway > LAN dhcp leases Page:
1 Reserve a private IP address for the computer or game device MAC address. 2 Designate the device as a DMZ device. You can reserve IP addresses for multiple devices, but only one can be designated as the gaming DMZ at once. Home Print X Exit 38 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Configuring the Gateway This section describes the Gateway configuration pages in the SBG940 Setup Program:
Gateway > STATUS Page Gateway > WAN Page Gateway > LAN nat config Page Gateway > LAN dhcp server config Page Gateway > LAN dhcp leases Page Gateway > PORT FORWARDING status Page Gateway > PORT FORWARDING config Page Gateway > PORT TRIGGERS predefined Page Gateway > PORT TRIGGERS custom Page Gateway > LOG Page After you edit some fields and click Apply, you are warned that you must reboot for your change to take effect. Rebooting takes 10 to 15 seconds. After rebooting, you must log in again. Home Print X Exit 39 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Gateway > STATUS Page This page displays the gateway status information:
These fields display settings that are set on the other Gateway pages. For field descriptions, see the following subsections that describe the fields on each tab. Home Print X Exit 40 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Gateway > WAN Page Use this page to configure the external (public) wide area network (WAN) interface:
Gateway > WAN page fields Field Host Name Enable DHCP Client
(obtain dynamic IP address) Disable DHCP Client (use static IP address) Description If the cable provider requires a hostname to access to their network, type the hostname they provided in this field. The default is None. Enabling the DHCP client causes the wireless gateway to automatically obtain the public IP address, subnet mask, domain name, and DNS server(s). Most commonly, the DHCP client is enabled if the cable provider automatically assigns a public IP address from their DHCP server. Enable DHCP Client is selected by default. If the cable provider does not automatically assign a public IP address using DHCP, they must provide a static IP address. Select Disable DHCP Client. When you disable the DHCP client, you must type the static IP address, subnet mask, DNS server(s), and domain name (if necessary) in the fields provided. Disable DHCP Client is not selected by default. Static IP Address Static IP Subnet Mask WAN Default Gateway If Disable DHCP Client is selected, type the static IP address provided by the cable provider in dotted-decimal format. The default is None. If Disable DHCP Client is selected, type the subnet mask associated with the static IP address in dotted-decimal format. The default is None. When using a Static IP Address from the cable provider, type the default gateway IP address on the WAN for the SBG940 in dotted-decimal format. Home Print X Exit 41 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Gateway > WAN page fields (continued) Field Description DNS IP Address 1 DNS IP Address 2 DNS IP Address 3 TCP Session Wait Timeout UDP Session Wait Timeout ICMP Session Wait Timeout Apply The cable provider DNS server provides name-to-IP address resolution. If the cable provider does not automatically assign DNS addresses from their DHCP server, they must provide at least one DNS server IP address to enter in these fields in dotted-decimal format. The default is None. Sets the maximum time in seconds to wait before assuming a TCP session has timed out. The default is 24 hours. Sets the maximum time in seconds to wait before assuming a UDP session has timed out. The default is 300 seconds (5 minutes). Sets the maximum time in seconds to wait before assuming an ICMP session has timed out. The default is 300 seconds (5 minutes). Click to apply your changes. Home Print X Exit 42 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Gateway > LAN nat config Page Use this page to enable NAT and add clients to the CURRENT NAT PASSTHROUGH list:
Gateway > LAN nat config page fields Field or Button Description LAN Enable NAT Apply NEW NAT PASSTHROUGH MAC Address Bypass Firewall
(True DMZ) Add CURRENT NAT PASSTHROUGH Delete If enabled, the single HFC IP Address (public IP address) assigned by the cable provider is mapped to many private IP addresses on the SBG940 LAN. Click to apply your changes. You must reboot the SBG940. Specifies up to 32 computers as passthrough clients not subject to NAT, using their MAC addresses. Type the passthrough client MAC address. The format is 16 hexadecimal numerals. Select this box to set the NAT passthrough computer as a DMZ client. Use this setting with extreme caution because a DMZ client is completely open to Internet hackers. Click to add the MAC address to the CURRENT NAT PASSTHROUGH list. Lists the computers on the LAN that are configured for NAT passthrough. Click to delete the selected MAC address from the NAT passthrough list. Home Print X Exit 43 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Gateway > LAN dhcp server config Page Only experienced network administrators should use this page to perform advanced DHCP server configuration:
CAUTION!
Do not modify these settings unless you are an experienced network administrator with strong knowledge of IP addressing, subnetting, and DHCP. Gateway > LAN dhcp server config page fields Field LAN IP Address LAN IP Subnet Mask Starting IP Address
# of DHCP Users Description You can type the IP address of the SBG940 for your private LAN. The default is 192.168.0.1. Displays the subnet mask in dotted-decimal format. The default is 255.255.255.0. Enter the starting IP address to be assigned by the SBG940 DHCP server to clients in dotted-decimal format. The default is 192.168.0.2. Sets the number of clients for the SBG940 DHCP server to assign a private IP address. There are 253 possible client addresses. The default is 253. DHCP Server Lease Time Sets the time in seconds that the SBG940 DHCP server leases an IP address to a client. The default is 3600 seconds (60 minutes). Domain Name Time To Live Interface Maximum Transmission Unit Apply Sets the domain name for the SBG940 LAN. The default is None. Sets the TTL (hop limit) for outbound packets. The default is 64. Sets the SBG940 LAN MTU in bytes. The minimum is 68 bytes. The default is 1500 bytes. Click to apply your changes. You must reboot the SBG940. Home Print X Exit 44 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Gateway > LAN dhcp leases Page Use this page to configure DHCP leases:
Gateway > LAN dhcp leases page fields Field GAMING DMZ Enable Gaming DMZ
(Gaming) DMZ Host Home Print Description Select this box to designate the selected computer or gaming device as the gaming DMZ host. For more information, see Configuring a Gaming DMZ Host. This can be useful if you have difficulties running certain applications; typically gaming applications. The gaming DMZ host is a computer with a reserved IP address designated as the default DMZ host. Only one gaming DMZ host can be active at once. The gaming DMZ host is not protected by the firewall. It is open to communication or hacking from any computer on the Internet. Consider carefully before configuring a computer to be in the DMZ. The benefit of using a gaming DMZ host instead of a NAT passthrough host is that a gaming DMZ host does not require a public IP address as does a NAT passthrough host. If the application requires a public IP address, configure the computer for NAT passthrough on the Gateway > LAN nat config Page. X Exit SBG940 User Guide 45 Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Gateway > LAN dhcp leases page fields (continued) Field Description RESERVE NEW IP ADDRESS You can reserve up to 32 IP addresses assigned by the SBG940 DHCP server for specific LAN clients. For example, to ensure that they always receive the same private IP address, you can reserve IP addresses for a private FTP server or gaming DMZ device. MAC Address IP Address Host Name Type the MAC address of the DHCP client for which a reserved IP address is required. The format is 16 hexadecimal numerals. Sets the host portion of the reserved IP address for the LAN client having the specified MAC address. When the LAN client requests an IP address, the SBG940 DHCP server assigns the client this IP address. If your ISP requires a hostname to access their network, enter the hostname provided to you in the Host Name field. Add CURRENTLY RESERVED IP ADDRESSES MAC Address IP Address Host Name Method Delete Delete Click Add to reserve a new IP address. Displays all DHCP clients having reserved IP addresses. Displays the client MAC address. Displays its reserved IP address Displays its host name. Displays dynamic and static lease status. Add or delete dynamic or static lease status in this field. Click this box to remove the reserved IP address for the client. Click this button to remove the reserved IP addresses for clients designated by the Delete box. Gateway > PORT FORWARDING status Page Use this page to display the configured port forwarding entries on the SBG940 LAN. The fields are the same as on the Gateway > PORT FORWARDING config Page:
Home Print X Exit 46 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Gateway > PORT FORWARDING config Page Use this page to configure up to 32 virtual servers:
Gateway > PORT FORWARDING config page fields Field Description ADD NEW PORT FORWARDING ENTRY You can configure up to 32 virtual servers. If you select Custom, you must set the Name, Port Start, Port End, and LAN IP Address. Template Name Port Start If you select a predefined template such as HTTP or FTP, the Name, Port Start, Port End values are provided. You only need to enter LAN IP Address and change default values only if necessary. Type a unique identifier for the custom virtual server. The typical practice is to use the protocol as a unique identifier (for example ftp). Sets the LAN internal interface port or the start of a port range. Inbound Internet connection requests are statically mapped to this port. The ports used by some common applications are:
FTP HTTP NTP Secure Shell SMTP e-mail Telnet 20, 21 80 123 22 25 23 Port End If a range of ports is required, sets the end of the port range. Home Print X Exit 47 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Gateway > PORT FORWARDING config page fields (continued) Field Description LAN IP Address Sets the private LAN IP address for the port forwarding page. An Internet user must know the public IP address to access any port forwarding entry you define on the private LAN. Enable Add Select this box to enable the port forwarding entries to be accessed through NAT. Click to add the virtual server to the PORT FORWARDING list. PORT FORWARDING Displays the configured custom virtual servers. Gateway > PORT TRIGGERS predefined Page When you run a PC application that accesses the Internet, it communicates with a computer on the Internet. In some applications, especially gaming, the computer on the Internet also communicates with your PC. Because NAT does not normally allow these incoming connections, the SBG940 supports port triggering. The SBG940 is preconfigured with port triggering for common applications. You can also configure additional port triggers if needed. Configuring port triggers for an application requires:
You can use the default values for the remaining parameters. The application transport protocol TCP or UDP The application port number Home Print X Exit 48 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Only one computer at a time connected to the SBG940 can use an application requiring port triggering. Use this page to view predefined port triggers:
Gateway > PORT TRIGGERS predefined page fields Field Description Name Enable Protocol Port Range Session Chaining Session Interval Address Replace Multi Host Displays the unique name for the port triggers. This is typically the protocol name. Select this box to activate the port triggers for the predefined application. Displays the transport protocol for the port trigger TCP or UDP. Displays the port range (From/To) for the port trigger. Displays the session chaining selection for the port trigger Disable, TCP, or TCP/UDP. Displays the session interval set for the port trigger. Displays the address replacement method for the port trigger. Displays the multi host selection for the port trigger. Home Print X Exit 49 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Gateway > PORT TRIGGERS custom Page Use this page to create a custom port trigger:
Gateway > PORT TRIGGERS custom page fields Field Description ADD NEW SPECIAL APPLICATION Name Enable Protocol Port Range
(From:To) Session Chaining Session Interval Enter the unique name for the port trigger. This is typically the protocol. Select this box to enable the custom port trigger. Sets the transport protocol for the port trigger TCP or UDP. Sets the port range for the port trigger. Type the start of the range in the left field and the end in the right field. Enable session chaining if the application needs to open one or more ports in different ranges to operate properly. The options are Disable, TCP, or TCP/UDP. Sets the session interval for the application:
If the port triggers detect traffic on the Port Range within the Session Interval, it is considered to be related to the initial session. If the port triggers detect traffic on the Port Range after the Session Interval expires, it is considered to be a new and unique session. Address Replace Multi Host Add Sets the address replacement method for the application. Select if appropriate for the application. Click to add the port trigger to the PORT TRIGGERS TABLE. Home Print X Exit 50 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Gateway > PORT TRIGGERS custom page fields (continued) Field Description PORT TRIGGERS TABLE Lists all port triggers you defined and their parameters. Priority Port Select the port to have a priority status. Gateway > LOG Page Use this page to view detailed information about the gateway:
Gateway > LOG page fields Field Time Priority Code Message Description The date and time in the format yyyy-mm-dd hh:mm:ss Indicates the importance of the message. Displays a code associated with the message. Describes the event. Home Print X Exit 51 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Configuring TCP/IP Configuring TCP/IP in Windows XP Configuring TCP/IP in Windows 2000 Configuring TCP/IP in Windows 95, Windows 98, or Windows Me You must be sure all client computers are configured for TCP/IP (a protocol for communication between computers). Perform one of:
After configuring TCP/IP, perform one of the following to verify the IP address:
Verifying the IP Address in Windows 95, Windows 98, or Windows Me Follow the instructions in your Macintosh or UNIX user manual Follow the instructions in your Macintosh or UNIX user manual Verifying the IP Address in Windows 2000 or Windows XP Configuring TCP/IP in Windows 95, Windows 98, or Windows Me 1 On the Windows Desktop, click Start. 2 Select Settings and then Control Panel from the pop-up menus to display the Control Panel window:
Home Print X Exit 52 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 3 Double-click the Network icon to display the Network window:
Although your SBG model number may be different than in the images in this guide, the procedure is the same. 4 5 6 Select the Configuration tab. Verify that TCP/IP is installed for the adapter used to connect to the SBG940. If TCP/IP is installed, skip to step 10. If TCP/IP is not installed for the adapter, continue with step 6. Select the adapter to use for the SBG940 connection and click Add. The Select Network Component Type window is displayed:
Home Print X Exit 53 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 7 Click Protocol and click Add. The Select Network Protocol window is displayed:
8 Click Microsoft in the Manufacturers section and click TCP/IP in the Network Protocols section. 9 Click OK. 10 Click TCP/IP on the Network window. If there is more than one TCP/IP entry, choose the one for the Ethernet card or USB port connected to the SBG940. 11 Click Properties. The TCP/IP Properties window is displayed:
12 Click the IP Address tab. 13 Click Obtain an IP address automatically. 14 Click OK to accept the TCP/IP settings. 15 Click OK to close the Network window. 16 Click OK when prompted to restart the computer and click OK again. When you complete TCP/IP configuration, go to Verifying the IP Address in Windows 95, Windows 98, or Windows Me. Home Print X Exit 54 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Configuring TCP/IP in Windows 2000 1 On the Windows Desktop, click Start. 2 Select Settings and then Control Panel from the pop-up menus to display the Control Panel window:
3 Double-click the Network and Dial-up Connections icon to display the Network and Dial-up Connections window:
Home Print X Exit 55 SBG940 User Guide
1 | User Manual Part 2 | Users Manual | 2.03 MiB |
Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 4 Click Local Area Connection number. The value of number varies from system to system. The Local Area Connection number Status window is displayed:
5 Click Properties. Information similar to the following window is displayed:
6 If Internet Protocol (TCP/IP) is in the list of components, TCP/IP is installed. You can skip to step 10. If Internet Protocol (TCP/IP) is not in the list, click Install. The Select Network Component Type window is displayed:
Home Print X Exit 56 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 7 Click Protocol on the Select Network Component Type window and click Add. The Select Network Protocol window is displayed:
8 Click Internet Protocol (TCP/IP). 9 Click OK. The Local Area Connection number Properties window is re-displayed. 10 Be sure the box next to Internet Protocol (TCP/IP) is selected. Home Print X Exit 57 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 11 Click Properties. The Internet Protocol (TCP/IP) Properties window is displayed:
12 Be sure Obtain IP address automatically and Obtain DNS server address automatically are selected. 13 Click OK to accept the TCP/IP settings. 14 Click Close to close the Local Area Connection number Properties window. 15 Click OK when prompted to restart the computer and click OK again. When you complete the TCP/IP configuration, go to Verifying the IP Address in Windows 2000 or Windows XP. Home Print X Exit 58 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Configuring TCP/IP in Windows XP 1 On the Windows desktop, click Start to display the Start window:
2 Click Control Panel to display the Control Panel window. The display varies, depending on the Windows XP view options. If the display is a Category view as shown below, continue with step 3. Otherwise, skip to step 5. Home Print X Exit 59 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 3 Click Network and Internet Connections to display the Network and Internet Connections window:
4 Click Network Connections to display the LAN or High-speed Internet connections. Skip to step 7. 5 If a classic view similar to below is displayed:
6 Double-click Network Connections to display the LAN or High-speed Internet connections. Home Print X Exit 60 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 7 Right-click on the network connection. If more than one connection is displayed, be sure to select the one for your network interface:
8 Select Properties from the pop-up menu to display the Local Area Connection Properties window:
9 On the Local Area Connection Properties window, be sure Internet Protocol (TCP/IP) is selected. If it is not selected, select it. Home Print X Exit 61 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 10 Select Internet Protocol (TCP/IP) and click Properties to display the Internet Protocol (TCP/IP) Properties window:
11 Verify that the settings are correct, as shown above. 12 Click OK to close the TCP/IP Properties window. 13 Click OK to close the Local Area Connection Properties window. When you complete the TCP/IP configuration, go to Verifying the IP Address in Windows 2000 or Windows XP. Home Print X Exit 62 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Verifying the IP Address in Windows 95, Windows 98, or Windows Me To check the IP address:
1 On the Windows Desktop, click Start. 2 3 Select Run. The Run window is displayed. Type winipcfg.exe and click OK. The IP Configuration window is displayed. The Ethernet Adapter Information field will vary depending on the system, as shown in the following examples:
The values for Adapter Address, IP Address, Subnet Mask, and Default Gateway on the PC will be different than in the images. In Windows 98, if Autoconfiguration is displayed before the IP Address as in the following image, call your service provider. Select the adapter name the Ethernet card or USB device. 4 5 Click Renew. 6 Click OK after the system displays an IP address. If after performing this procedure the computer cannot access the Internet, call your cable provider for help. Home Print X Exit 63 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Verifying the IP Address in Windows 2000 or Windows XP To check the IP address:
1 On the Windows Desktop, click Start. 2 3 4 Select Run. The Run window is displayed. Type cmd and click OK to display a command prompt window. Type ipconfig and press ENTER to display the IP configuration. A display similar to the following indicates a normal configuration:
If an Autoconfiguration IP Address is displayed as in the following window, there is an incorrect connection between the PC and the SBG940 or there are cable network problems. Check the cable connections and determine if you can view cable-TV channels on your television:
After verifying the cable connections and proper cable-TV operation, renew the IP address. Home Print X Exit 64 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB To renew the IP address:
1 Type ipconfig /renew and press ENTER. If a valid IP address is displayed as shown, Internet access should be available. Type exit and press ENTER to return to Windows. 2 If after performing this procedure the computer cannot access the Internet, call your cable provider for help. Home Print X Exit 65 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Setting Up Your Wireless LAN You can use the SBG940 as an access point for a wireless LAN (WLAN) without changing its default settings. Caution!
To prevent unauthorized eavesdropping or access to WLAN data, you must enable wireless security. The default SBG940 settings provide no wireless security. After your WLAN is operational, be sure to enable wireless security. To enable security for your WLAN, you can do the following on the SBG940:
To Perform Use in Setup Program Encrypt wireless transmissions and restrict WLAN access Further prevent unauthorized WLAN intrusions Encrypting Wireless LAN Transmissions Wireless > SECURITY basic Page Restricting Wireless LAN Access Wireless > SECURITY advanced Page Connect at least one computer to the SBG940 Ethernet or USB port to perform configuration. Do not attempt to configure the SBG940 over a wireless connection. You need to configure each wireless client (station) to access the SBG940 LAN as described in Configuring the Wireless Clients. Caution!
Never provide your ESSID, WPA or WEP passphrase, or WEP key to anyone who is not authorized to use your WLAN. For descriptions of all wireless configuration fields, see Configuring a Wireless Client with the Network Name
(ESSID). Another common-sense step to improve wireless security is to place wireless components away from windows. This decreases the signal strength outside the intended area. Home Print X Exit 66 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Encrypting Wireless LAN Transmissions To prevent unauthorized viewing of data transmitted over your WLAN, you must encrypt your wireless transmissions. Use the Wireless > SECURITY basic Page to encrypt your transmitted data. Choose one of:
Configure on the SBG940 Required On Each Wireless Client If all of your wireless clients support Wi-Fi Protected Access (WPA), we recommend Configuring WPA on the SBG940 If you use a local pre-shared key (WPA-PSK) passphrase, you must configure the identical passphrase to the SBG940 on each wireless client. Home and small-office settings typically use a local passphrase. Configuring a RADIUS server requires specialized knowledge that is beyond the scope of this guide. For more information, contact your network administrator. Otherwise, perform Configuring WEP on the SBG940 You must configure the identical WEP key to the SBG940 on each wireless client. Is much easier to configure Provides much stronger encryption and is more secure Provides authentication to ensure that authorized users only can log in to your WLAN If all of your wireless clients support WPA encryption, we recommend using WPA instead of WEP because WPA:
Will be incorporated into the new IEEE 802.11i wireless networking standard For new wireless LANs, we recommend purchasing client adapters that support WPA, such as the Motorola Wireless Notebook Adapter WN825G, Wireless PCI Adapter WPCI810G, and Wireless USB Adapter WU830G. For more information about the benefits of WPA, see the Wi-Fi Protected Access web page http://www.wifialliance.org/OpenSection/protected_access.asp. Uses a standard algorithm on all compliant products to generate a key from a textual passphrase Home Print X Exit 67 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Configuring WPA on the SBG940 To enable WPA and set the key on the SBG940:
1 On the SBG940 Setup Program left panel, click Wireless. 2 Click the SECURITY tab to display the Wireless > SECURITY basic page:
In the Security Mode field, select WPA and click Apply. 3 4 Under WPA CONFIGURATION, choose one WPA Encryption type. Because performance may be slow with TKIP, we recommend choosing AES if your clients support AES:
TKIP AES Temporal Key Integrity Protocol provides data encryption including a per-packet key mixing function, message integrity check (MIC), initialization vector (IV) and re-keying mechanism. The Advanced Encryption Standard algorithm implements symmetric key cryptography as a block cipher using 128-bit keys. We recommend this setting if all of your wireless clients support AES. The Motorola client adapters shown in Optional Accessories support AES. Home Print X Exit 68 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 5 Choose the WPA Authentication type:
Remote
(Radius) Local
(WPA-PSK) If a Remote Authentication Dial-In User Service (RADIUS) server is available, you can select this option and go to step 6. A RADIUS server is typically used in a large corporate location. If you choose Pre-Shared Key (PSK) local authentication, if the passphrase on any client supporting WPA matches the PSK Passphrase set on the SBG940, the client can access the SBG940 WLAN. To set the PSK Passphrase, go to step 7. A local key is typically used in a home or small office. 6 For Remote (Radius) authentication only, set:
The port used for remote authentication through a RADIUS server. It can be from 0 to 65535. The key for remote authentication. It can be from 0 to 255 ASCII characters. Radius Port Radius Key Radius Server Type Radius Server The RADIUS server IP address in dotted-decimal format (xxx.xxx.xxx.xxx). Currently IPv4 only. 7 For Local (WPA-PSK) authentication only, set:
PSK Passphrase The PSK password containing from 8 to 63 ASCII characters. You must set the identical passphrase on each WLAN client (see Configuring a Wireless Client for WPA). 8 Click Save Changes. If you need to restore the wireless defaults, click Reset Wireless Defaults. Home Print X Exit 69 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Configuring WEP on the SBG940 Use Wired Equivalent Privacy (WEP) only if you have wireless clients that do not support WPA. Caution!
If you use WEP encryption, you must configure the same WEP key on the SBG940 access point and all wireless clients (stations). Never provide your WEP key or passphrase to anyone who is not authorized to use your WLAN. To enable WEP and set the key on the SBG940:
1 On the SBG940 Setup Program left panel, click Wireless. 2 Click the SECURITY tab to display the Wireless > SECURITY basic page:
3 4 In the Security Mode field, select WEP and click Apply. In the WEP Passphrase field, type a passphrase containing from 8 to 31 ASCII characters. For privacy, your passphrase displays as dots. Home Print X Exit 70 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 5 Click Generate WEP Keys. The following window is displayed:
6 Click OK. The WEP CONFIGURATION fields now appear something like:
Before performing step 7, consider the following:
If all of your wireless adapters support 128-bit encryption, you can select Enable 128 Bit. Otherwise, you must select Enable 64 Bit. For a WLAN client equipped with a Motorola wireless adapter, you can enter the WEP Passphrase when you perform Configuring a Wireless Client for WEP. For all other wireless adapters, you will probably need to enter the generated WEP key that you designate in step 7. 7 Under WEP CONFIGURATION, set:
WEP Authentication Encryption Key 1 to Key 4 Sets whether shared key authentication is enabled to provide data privacy on the WLAN:
Open System Any WLAN client can transmit data to any other client without authentication. It is the default, if the Security Mode is set to WEP. Shared Key The SBG940 authenticates and transfers data to and from all clients having shared key authentication enabled. We recommend this setting. Use a WEP key length that is compatible with your wireless client adapters. Choose one of:
Enable 64-Bit Use only if you have wireless clients that do not support 128-bit encryption Enable 128-Bit We recommend this setting for stronger encryption; it is supported by the Motorola WN825G and WPCI810G wireless adapters and most current wireless adapters Select the active key (1 to 4). Only one key can be active. You can generate WEP keys from a passphrase as described in steps 4 to 6 or type non-case-sensitive hexadecimal characters 0 to 9 and A to F to define up to:
Four 10-character long key 64-bit WEP keys Four 26-character long 128-bit WEP keys We recommend changing the WEP keys frequently. Never provide the WEP key to anyone who is not authorized to use your WLAN. 8 Click Save Changes to save your changes. If you need to restore the wireless defaults, click Reset Wireless Defaults. Home Print X Exit 71 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Restricting Wireless LAN Access The default SBG940 wireless settings enable any computer having a compatible wireless adapter to access your WLAN. To protect your network from unauthorized intrusions, you can restrict access to your WLAN to a limited number of computers on the Wireless > SECURITY advanced Page. You can configure one or both of:
Configure on the SBG940 Required On Each Wireless Client Perform Configuring the Wireless Network Name on the SBG940 to disable Extended Service Set Identifier (ESSID) broadcasting to enable closed network operation Perform Configuring a MAC Access Control List on the SBG940 to restrict access to wireless clients with known MAC addresses You must configure the identical ESSID (network name) to the SBG940. No configuration is required on the client. Home Print X Exit 72 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Unauthorized individuals who scan for unsecured WLANs cannot access your WLAN Configuring the Wireless Network Name on the SBG940 If you disable ESSID broadcasting on the SBG940, the SBG940 does not transmit the network name (ESSID). This provides additional protection because:
Only wireless clients configured with your network name can communicate with the SBG940 Closed network operation is an enhancement of the IEEE 802.11b and IEEE 802.11g standards. If you select Disable ESSID Broadcast, you must perform Configuring a Wireless Client with the Network Name
(ESSID) on all WLAN clients (stations). Never provide your ESSID to anyone who is not authorized to use your WLAN. To configure the ESSID on the SBG940:
1 2 On the left panel, click Wireless. 3 Click the NETWORK tab to display:
Start the SBG940 Setup Program as described in Starting the SBG940 Setup Program. 4 In the ESSID field, type a unique name. It can be any alphanumeric, case-sensitive string up to 32 characters. The default is Motorola. Do not use the default ESSID. 5 Click Save Changes to save your changes. 6 To restrict WLAN access to clients configured with the same Network Name (ESSID) as the SBG940, click the SECURITY tab. Home Print X Exit 73 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 7 Click advanced to display the Wireless > SECURITY advanced Page:
8 Select Disable ESSID Broadcast to restrict WLAN access to clients configured with the same Network Name (ESSID) as the SBG940. 9 Click Apply to save your changes. Home Print X Exit 74 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Configuring a MAC Access Control List on the SBG940 You can restrict wireless access to one to 32 wireless clients, based on the client MAC address. To configure a MAC access control list:
1 On the SBG940 Setup Program left panel, click Wireless. 2 Click the SECURITY tab. 3 Click advanced to display the Wireless > SECURITY advanced Page:
4 5 To restrict wireless access to systems in the MAC access control list, select Allow Only Listed Stations Access and click Apply. To add a wireless client, type its MAC address in the format xx:xx:xx:xx:xx:xx in the New Station field and click Add Station. You can add up to 32 wireless clients to the MAC access control list. Home Print X Exit 75 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Configuring the Wireless Clients For each wireless client computer (station), install the wireless adapter such as a Motorola WN825G, WPCI810G, or WU830G following the instructions supplied with the adapter. Be sure to:
1 2 3 Insert the adapter in the PCMCIA or PCI slot or connect it to the USB port. Insert the CD-ROM for the adapter in the CD-ROM drive on the client. Install the device software from the CD. Step 1 Step 3 Step 2 Step 3 Step 2 Step 1 Configure the adapter to obtain an IP address automatically. The Motorola wireless adapters are supplied with a client configuration program called Wireless Client Manager, which is installed in the Windows Startup group. On a PC with Wireless Client Manager installed, the the icon to launch the utility. You may need to do the following to use a wireless client computer to surf the Internet:
icon is displayed on the Windows task bar. Double-click If You Performed On Each Client, You Need to Perform Configuring WPA on the SBG940 Configuring WEP on the SBG940 Configuring the Wireless Network Name on the SBG940 Configuring a Wireless Client with the Network Name Configuring a Wireless Client for WEP Configuring a Wireless Client for WPA
(ESSID) Configuring a MAC Access Control List on the SBG940 No configuration on client required Home Print X Exit 76 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Configuring a Wireless Client for WPA If you enabled WPA and set a PSK Passphrase by Configuring WPA on the SBG940, you must configure the same passphrase (key) on each wireless client. The SBG940 cannot authenticate a client if:
WPA is enabled on the SBG940 but not on the client For information about the WPA support in Windows XP, visit:
The client passphrase does not match the SBG940 PSK Passphrase WPA Wireless Security for Home Networks http://www.microsoft.com/WindowsXP/expertzone/columns/
bowman/03july28.asp Overview of the WPA Wireless Security Update in Windows XP http://support.microsoft.com/?kbid=815485 You can download the Microsoft Windows XP Support Patch for Wi-Fi Protected Access from http://www.microsoft.com/downloads/details.aspx?FamilyId=009D8425-CE2B-47A4-ABEC-274845DC9E91&disp laylang=en Caution!
Never provide the PSK Passphrase to anyone who is not authorized to use your WLAN. Shared Key Authentication is enabled on the SBG940 but not on the client The client WEP key does not match the SBG940 WEP key Configuring a Wireless Client for WEP If you enabled WEP and set a key by Configuring WEP on the SBG940, you must configure the same WEP key on each wireless client. The SBG940 cannot authenticate a client if:
On a WLAN client equipped with a Motorola wireless adapter, you can enter the WEP Passphrase you set when you configured the SBG940. For all other wireless adapters, you must enter the 64-bit or 128-bit WEP key generated by the SBG940. Caution!
Never provide the WEP key to anyone who is not authorized to use your WLAN. Configuring a Wireless Client with the Network Name (ESSID) To distinguish it from other nearby WLANs, you can identify your WLAN with a unique network name (also known as a network identifier or ESSID). When prompted for the network identifier, network name, or ESSID, type the name set in the ESSID field on the Wireless > NETWORK Page in the SBG940 Setup Program. For more information, see Configuring the Wireless Network Name on the SBG940. After you specify the network name, many wireless cards or adapters automatically scan for an access point such as the SBG940 and the proper channel and data rate. If your card requires you to manually start scanning for an access point, do so following the instructions in the documentation supplied with the card. Never provide the ESSID to anyone who is not authorized to use your WLAN. Home Print X Exit 77 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Wireless Pages in the SBG940 Setup Program Use the Wireless pages to control and monitor the wireless interface:
Wireless > STATUS Page Wireless > NETWORK Page Wireless > SECURITY basic Page Wireless > SECURITY advanced Page Wireless > STATISTICS page After you edit some fields and click Apply, you are warned that you must reboot for your change to take effect. Rebooting takes 10 to 15 seconds. After rebooting, you must log in again. Home Print X Exit 78 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Wireless > STATUS Page You can use this display-only page to:
View the wireless interface status Help perform Troubleshooting for wireless network problems Wireless > STATUS Page Fields Regulatory Domain ESSID Channel RTS Threshold Frag Threshold MAC Address Security Mode MAC Access Control Indicates the country the SBG940 is manufactured for. The list of channels depends on the countrys standards for operation of wireless devices. Depending on the domain set at the factory, USA FCC, Europe, Spain, France, Japan, or some other country name is displayed. Displays the ESSID set on the Wireless > NETWORK Page. For more information, see Configuring the Wireless Network Name on the SBG940. Never provide the ESSID to anyone who is not authorized to use your WLAN. Displays the radio channel for the access point. If you encounter interference, you can set a different channel on the Wireless > NETWORK Page. Displays the Request to Send Threshold set on the Wireless > NETWORK Page. Displays the Fragmentation Threshold set on the Wireless > NETWORK Page. Displays the SBG940 MAC address. Displays the enabled wireless encryption type. For more information, see Configuring WPA on the SBG940 or Configuring WEP on the SBG940. Displays the MAC Access Control setting (see Configuring a MAC Access Control List on the SBG940):
Allow Listed Only clients in the MAC access control list can access the WLAN. Allow Any Station Access Any wireless client can access the WLAN. MAC Access Control List Displays the MAC addresses of wireless clients having access (see Configuring a MAC Access Control List on the SBG940). Home Print X Exit 79 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Wireless > NETWORK Page Use this page for:
You can use the SBG940 to operate a WLAN without changing its default settings. Configuring the Wireless Network Name on the SBG940 Configuring other WLAN settings Wireless > NETWORK page fields Field WIRELESS Enable Wireless Interface ESSID Channel Description Select this box to enable the wireless interface. Sets a unique network name for the SBG940 WLAN to distinguish between multiple WLANs in the vicinity. If you select Disable ESSID Broadcast on the Wireless > SECURITY advanced Page, all clients on the WLAN must have the same ESSID (network name) as the SBG940. It can be any alphanumeric, case-sensitive string up to 32 characters. The default is Motorola. We strongly recommend not using the default. Never provide the ESSID to anyone who is not authorized to use your WLAN. Sets the wireless radio channel. You can change the channel if you encounter interference on the default channel. The default is 1 (one), except in countries where the first channel permitted for wireless operation is not one. Home Print X Exit 80 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Wireless > NETWORK page fields (continued) Field Description Operating Mode ADVANCED SETUP Transmit Power RTS Threshold Fragmentation Threshold Beacon Period DTIM Period Sets how the SBG940 communicates with wireless clients (stations):
11b/11g Standard Enables all IEEE 802.11b and IEEE 802.11g clients to work with the SBG940. We recommend using this default setting in most cases because it is more flexible. 11g Enhanced Choose this option only if all IEEE 802.11g client adapters on the network support the performance-enhancing features of the IEEE 11g Enhanced mode. It is not supported by all IEEE 802.11g adapters. Sets the SBG940 wireless transmission power 1, 2, 5, 10, 25, 50, or 100 mW. The default is 32 mW. Transmission power control is an optional IEEE 802.11b feature. The Request To Send Threshold sets the minimum packet size for which the SBG940 issues an RTS before sending a packet. A low RTS Threshold can help when many clients are associated with the SBG940 or the clients are far apart and can detect the SBG940 but not each other. It can be 0 to 2347 bytes. The default is 2347. Sets the size at which packets are fragmented (sent as several packets instead of as one packet). A low Fragmentation Threshold can help when communication is poor or there is a significant interference. It can be 256 to 2346 bytes. The default is 2346. Sets the time between beacon frames sent by the SBG940 for wireless network synchronization. It can be from 1 to 999 ms. The default is 100 ms. The delivery traffic indication message (DTIM) period is the number of Beacon Periods that elapse before a wireless client operating in power save mode listens for buffered broadcast or multicast messages from the SBG940. It can be from 1 to 99999. The default is 3. Home Print X Exit 81 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Wireless > SECURITY basic Page Use this page to configure how your SBG940 encrypts wireless transmissions. For information about using this page, see Encrypting Wireless LAN Transmissions. After you enable WEP or WPA on the SBG940, you must configure each WLAN client as described in Configuring the Wireless Clients. Caution!
The default Security Mode setting None provides no security for transmitted data. Home Print X Exit 82 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Wireless > SECURITY advanced Page Use this page to configure advanced wireless security settings. Wireless > Security ADVANCED page fields Field or Button Description Disable ESSID Broadcast If selected, only wireless clients (stations) having the same Network Name (ESSID) as the SBG940 can communicate with the SBG940. Closed network operation is a SBG940 enhancement to IEEE 802.11b. The default is not selected (off). MAC ACCESS CONTROL LIST You can restrict wireless access to one to 32 wireless clients, based on the client MAC address. Allow Any Station Access Allow Only Listed Stations Access Apply Listed Stations Delete Home Print If selected, any wireless client can access the SBG940 WLAN. If selected, only wireless clients in the MAC access control list can access the SBG940 WLAN. Click to apply your change. Lists the wireless clients in the MAC access control list having access if Allow Only Listed Stations Access is selected. To delete a wireless client from the MAC access control list, select its Delete check box and click the Delete button. X Exit SBG940 User Guide 83 Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Wireless > Security ADVANCED page fields (continued) Field or Button Description ADD NEW STATION New Station Type the MAC address of the wireless client to add to the MAC access control list. Use the format xx:xx:xx:xx:xx:xx. The MAC access control list can contain one to 32 clients. Add Station Click to add the New Station to the MAC access control list. Wireless > STATISTICS page Use this page to display wireless statistics. Wireless > STATISTICS page fields Field or Button Description Transmitted Fragment Count Multicast Transmitted Fragment Count Failed Count The number of acknowledged MAC protocol data units (MPDUs) with an address in the address 1 field or an MPDU with a multicast address in the address 1 field of type data or management. The number of transmitted fragments when the multicast bit is set in the destination MAC address of a successfully transmitted MAC service data unit (MSDU). When operating as a STA in an ESS, where these frames are directed to the AP, this implies having received an acknowledgment to all associated MPDUs. The number of MSDUs not transmitted successfully because the number of transmit attempts exceeded the IEEE 802.11b short or long retry limit. Retry Count The number of successfully transmitted MSDUs after one or more retransmissions. Home Print X Exit 84 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Wireless > STATISTICS page fields (continued) Field or Button Description The number of frames received where the Sequence Control field indicated the frame was a duplicate. The number of CTS messages received in response to RTS messages. The number of CTS messages not received in response to RTS messages. The number of acknowledgment messages not received when expected from a data message transmission. Multiple Retry Count The number of successfully transmitted MSDUs after more than one retransmission. Frame Duplicate Count Request To Send Success Count Request To Send Failure Count Acknowledge Failed Count Received Fragment Count Multicast Received Fragment Count Frame Check Sequence Error Count Transmitted Frame Count WEP Undecryptable Count The number of MSDUs received when the multicast bit was set in the destination MAC address. The number of successfully received MPDUs of type Data or Management. The number of FCS errors detected in a received MPDU. The number of successfully transmitted MSDUs. This number of frames received with the WEP subfield of the Frame Control field set to one and the WEP On key value mapped to the client MAC address. This indicates that the frame should not have been encrypted or was discarded due to the receiving client not having WEP enabled. Refresh Click to collect new data. Home Print X Exit 85 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Setting Up a USB Driver Setting Up a USB Driver in Windows 98 Setting Up a USB Driver in Windows 2000 Setting Up a USB Driver in Windows Me Setting Up a USB Driver in Windows XP The following subsections describe setting up a USB driver if you connect a PC to the USB port on the SBG940. Before connecting a PC to the USB port, perform one of the following procedures based on your Windows version:
The SBG940 USB driver does not support Macintosh or UNIX computers. For those systems, you can connect through Ethernet only. Caution!
Be sure the SBG940 Installation CD-ROM is inserted in the CD-ROM drive before you plug in the USB cable. If you have a problem setting up the USB driver, remove it by performing one of the following procedures:
Removing the USB Driver from Windows 98 or Windows Me Removing the USB Driver from Windows 2000 Removing the USB Driver from Windows XP Home Print X Exit 86 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Setting Up a USB Driver in Windows 98 1 Insert the SBG940 Installation CD-ROM in the CD-ROM drive. This CD contains the USB drivers and must be inserted and read by the PC before you connect the SBG940 to the PC. 2 Connect the USB cable as shown in USB Connection. A few seconds after you complete the USB connection, the Add New Hardware Wizard window is displayed:
3 Click Next. The following window is displayed:
4 Be sure Search for the best driver for your device is selected. Home Print X Exit 87 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 5 Click Next. The following window is displayed:
Be sure CD-ROM drive is the only box selected. 6 Click Next. The message Please wait while Windows searches for a new driver for this device is displayed. If the computer successfully locates the driver, you can skip to step 9. If the computer does not locate the driver, the previous window is displayed again. Select Specify a location and type the location of the CD-ROM drive:
7 To load the driver successfully, you may need to click Browse to manually select the NetMotCM.sys file on the CD-ROM. Home Print X Exit 88 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 8 Click Next. The following window is displayed:
9 Select The updated driver... and click Next. If the following window is not displayed, verify that the SBG940 Installation CD-ROM is properly inserted in the CD-ROM drive. If you still cannot find the correct driver file, click Cancel to cancel the installation and perform the procedure for Removing the USB Driver from Windows 98 or Windows Me. Then repeat this procedure. Although your SBG model number may be different than in the images in this guide, the procedure is the same. 10 After the window shown under step 9 is displayed, click Next. If a window with the message Copying Files... displays and asks for the CD-ROM drive, type the CD-ROM drive letter (for example, D:) and click OK. If an Insert Disk window similar to the one below is displayed, Windows 98 system files are needed to complete the installation. To install the files, insert your Windows 98 CD-ROM in the CD-ROM drive and click OK. Home Print X Exit 89 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB After all the necessary files are loaded, the following window is displayed to confirm a successful installation:
11 Click Finish. The Systems Settings Change window is displayed:
12 Click Yes to restart the computer. When you finish setting up the USB driver, you can continue with Configuring TCP/IP. If you have difficulties setting up the USB driver, perform Removing the USB Driver from Windows 98 or Windows Me and repeat this procedure. If that does not correct the problem, see the Regulatory, Safety, Software License, and Warranty Information card provided with the SBG940 for information about obtaining warranty service. Home Print X Exit 90 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Setting Up a USB Driver in Windows 2000 1 Insert the SBG940 Installation CD-ROM in the CD-ROM drive. This CD contains the USB drivers and must be inserted and read by the PC before you connect the SBG940 to the PC. 2 Connect the USB cable as shown in USB Connection. A few seconds after you complete the USB connection, the Found New Hardware window is displayed:
3 Click Next. The following window is displayed:
Although your SBG model number may be different than in the images in this guide, the procedure is the same. Be sure Search for a suitable driver for my device is selected. Home Print X Exit 91 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 4 Click Next. The following window is displayed:
Be sure CD-ROM drives is the only box selected. 5 Click Next. The following window is displayed:
6 Click Next. If the Insert Disk window is displayed, be sure the SBG940 Installation CD-ROM is in the CD-ROM drive and follow steps 7 to 12. Otherwise, you can skip to step 13. Home Print X Exit 92 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 7 On the Insert Disk window, click OK. The Files Needed window is displayed:
If necessary, select the CD-ROM drive in the Copy files from list. 8 9 Click Browse. 10 Locate the NetMotCM.sys file in the CD-ROM root directory. 11 Double-click the NetMotCM.sys file. The Files Needed window is displayed. 12 Click OK. The Found New Hardware Wizard window is displayed:
13 Click Finish to complete the installation. When you finish setting up the USB driver, you can continue with Configuring TCP/IP. If you have any difficulties setting up the USB driver, perform Removing the USB Driver from Windows 2000 and repeat this procedure. Home Print X Exit 93 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Setting Up a USB Driver in Windows Me 1 Insert the SBG940 Installation CD-ROM in the CD-ROM drive. This CD contains the USB drivers and must be inserted and read by the PC before you connect the SBG940 to the PC. 2 Connect the USB cable as shown in USB Connection. A few seconds after you complete the USB connection, the Add New Hardware Wizard window is displayed:
3 Click Next. Windows automatically searches for the correct USB drivers and installs them. If the installation is successful, the following window is displayed:
Although your SBG model number may be different than in the images in this guide, the procedure is the same. 4 If the window above is displayed, click Finish. Otherwise, be sure the SBG940 Installation CD-ROM is correctly inserted in the CD-ROM drive. When you finish setting up the USB driver, you can continue with Configuring TCP/IP. Home Print X Exit 94 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Setting Up a USB Driver in Windows XP 1 Insert the SBG940 Installation CD-ROM in the CD-ROM drive. This CD contains the USB drivers and must be inserted and read by the PC before you connect the SBG940 to the PC. 2 Connect the USB cable as shown in USB Connection. A few seconds after you complete the USB connection, the Found New Hardware Wizard window is displayed:
Be sure Install the software automatically is selected. 3 4 Click Next. Windows automatically searches for the correct USB drivers and installs them. If the installation is successful, the following window is displayed:
Although your SBG model number may be different than in the images in this guide, the procedure is the same. Home Print X Exit 95 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 5 Click Finish to complete the installation. Otherwise, be sure the SBG940 Installation CD-ROM is correctly inserted in the CD-ROM drive. When you finish setting up the USB driver, you can continue with Configuring TCP/IP. Removing the USB Driver from Windows 98 or Windows Me 1 On the Windows Desktop, right-click one of:
In Windows 98, the Network Neighborhood icon The Network window is displayed:
In Windows ME, the My Network Places icon Although your SBG model number may be different than in the images in this guide, the procedure is the same. 2 Click the Motorola SURFboard SBG940 USB Gateway. Home Print X Exit 96 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 3 Click Remove. The Network window no longer displays Motorola SURFboard SBG940 USB Gateway in the list:
4 Click OK. The System Settings Change window is displayed:
5 Disconnect the USB cable from the PC or SBG940. 6 Click Yes to restart the computer. 7 Insert the SBG940 Installation CD-ROM in the CD-ROM drive. After a short time, a window with language choices is displayed. Press the Esc key on the keyboard to exit the start-up screens. To start Windows Explorer, click Start and select Run to display the Run window. 8 9 10 Type explorer and click OK. Home Print X Exit 97 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB The Exploring window is displayed. Windows Explorer may appear different than in the image. There are variations between Windows versions and you can configure Windows Explorer as you like. 11 Double-click the Motorola SBG940 CD-ROM drive (D: in the image above). 12 Double-click remove or remove.exe to run the Remove utility from the SBG940 Installation CD-ROM. The SURFboard Cable Modem USB Driver Removal window is displayed:
13 Click Remove Driver. After you remove the USB driver, re-install it on the computer. Perform one of:
If you continue to have problems, contact your cable provider. Setting Up a USB Driver in Windows 98 Setting Up a USB Driver in Windows Me Home Print X Exit 98 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Removing the USB Driver from Windows 2000 1 On the Windows desktop, click Start. 2 Click Settings. 3 Click Control Panel to display the Control Panel window:
4 Double-click System to display the System Properties window. 5 Click the Hardware tab:
Home Print X Exit 99 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 6 Click Device Manager to display the Device Manager window:
Although your SBG model number may be different than in the images in this guide, the procedure is the same. 7 Double-click Network Adapters. 8 Click the Motorola SURFboard SBG940 USB Gateway. The Uninstall icon displays on the window near the top. 9 Click the Uninstall icon. The following window is displayed:
10 Click OK. 11 Close the Device Manager window. 12 Close the Control Panel window. 13 Insert the SBG940 Installation CD-ROM in the CD-ROM drive. 14 Press the Esc key on the keyboard to exit the start-up screens. 15 To start Windows Explorer, click Start and select Run to display the Run window. Home Print X Exit 100 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 16 On the Run window, type explorer and click OK to display Windows Explorer:
Windows Explorer may appear different than in the image. There are variations between Windows versions and you can configure Windows Explorer as you like. 17 Double-click My Computer. 18 Double-click the Motorola SBG940 CD icon (D: in the image). 19 Double-click remove or remove.exe to run the Remove utility from the SBG940 Installation CD-ROM. The SURFboard Cable Modem USB Driver Removal window is displayed:
20 Be sure the USB cable is disconnected. 21 Click Remove Driver. Informational messages similar to the ones shown are displayed on the SURFboard Cable Modem USB Driver Removal window. After you remove the USB driver, re-install it following Setting Up a USB Driver in Windows 2000. If you continue to have problems, contact your cable provider. Home Print X Exit 101 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Removing the USB Driver from Windows XP 1 On the Windows desktop, click Start to display the Start window:
2 Click Control Panel to display the Control Panel window. The display varies, depending on the Windows XP view options:
Home Print X Exit 102 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB If a Category view similar to the image under step 2 is displayed, click Performance and Maintenance to display the Performance and Maintenance window. Otherwise, skip to step 5. 3 4 Click System to display the System Properties window. Skip to step 6. Home Print X Exit 103 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB If a classic view similar to the following is displayed, double-click System to display the System Properties window:
5 6 Click the Hardware tab to display the Hardware page:
Home Print X Exit 104 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 7 Click the Device Manager button to display the Device Manager window:
Although your SBG model number may be different than in the images in this guide, the procedure is the same. 8 Double-click Network adapters. 9 Click the Motorola SURFboard SBG940 USB Gateway. The Uninstall icon displays on the window near the top. 10 Click the Uninstall icon. 11 Close the Device Manager and Control Panel windows. 12 Insert the SBG940 Installation CD-ROM in the CD-ROM drive. After a short time, a window with language choices is displayed. 13 Press the Esc key on the keyboard to exit the start-up screens. 14 To start Windows Explorer, click Start and select Run to display the Run window. Home Print X Exit 105 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 15 Type explorer and click OK to display Windows Explorer. Windows Explorer may appear slightly different than in the image. There are variations between Windows versions and you can configure Windows Explorer as you like. 16 Double-click My Computer. 17 Double-click the Motorola CD icon (D: in the image). 18 Double-click remove or remove.exe to run the Remove utility from the SBG940 Installation CD-ROM. The SURFboard Cable Modem USB Driver Removal window is displayed:
19 Be sure the USB cable is disconnected. 20 Click Remove Driver. Informational messages are displayed on the SURFboard Cable Modem USB Driver Removal window. After you remove the USB driver, re-install it following Setting Up a USB Driver in Windows XP. If you continue to have problems, contact your cable provider. Home Print X Exit 106 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Troubleshooting If the solutions listed here do not solve your problem, contact your cable provider. Before calling your cable provider, try pressing the reset button on the rear panel. Resetting the SBG940 may take 5 to 30 minutes. Your service provider may ask for the status of the lights as described in Front-Panel Lights and Error Conditions. Problem Possible Solutions Power light is off Check that the SBG940 is properly plugged into the electrical outlet. Check that the electrical outlet is working. Press the Reset button. Cannot send or receive data Problems related to unsuccessful USB driver installation On the top front panel, note which is the first light (starting from the left) that is off. This light indicates where the error occurred as described in Front-Panel Lights and Error Conditions. If you have cable TV, check that the TV is working and the picture is clear. If you cannot receive regular TV channels, the data service will not function. Check the coaxial cable at the SBG940 and wall outlet. Hand-tighten if necessary. Check the IP address. Follow the steps for verifying the IP address for your system. See Configuring TCP/IP. Call your cable provider if you need an IP address. Check that the Ethernet cable is properly connected to the SBG940 and the computer. Remove the USB driver. Follow the appropriate procedure for your system in Setting Up a USB Driver. The SBG940 Setup Program will not start The web cache is full or close to full. In Internet Explorer, choose Internet Options from the Tools menu, and click the General tab. Click Delete Files and Clear History. Then try Starting the SBG940 Setup Program again. A wireless client(s) cannot send or receive data Perform the first four checks in Cannot send or receive data. Check the Security Mode setting on the Wireless > SECURITY basic Page:
If you enabled WPA and configured a passphrase on the SBG940, be sure each affected wireless client has the identical passphrase. If this does not solve the problem, check whether the wireless client supports WPA. If you enabled WEP and configured a key on the SBG940, be sure each affected wireless client has the identical WEP key. If this does not solve the problem, check whether the client wireless adapter supports the type of WEP key configured on the SBG940. To temporarily eliminate the Security Mode as a potential issue, select None and click Apply. After resolving your problem, be sure to re-enable wireless security. On the Wireless > SECURITY advanced Page:
Check whether you turned on Disable ESSID Broadcast. If it is on, be sure the network name (ESSID) on each affected wireless client is identical to the ESSID on the SBG940. Check whether you enabled Allow Only Listed Stations Access. If you did, be sure the MAC address for each affected wireless client is correctly listed. For detailed information, see Setting Up Your Wireless LAN. Slow wireless transmission speed with WPA enabled On the Wireless > SECURITY basic Page, check whether the WPA Encryption type is TKIP. If all of your wireless clients support AES, change the WPA Encryption to AES as described in step 4 in Configuring WPA on the SBG940. Home Print X Exit 107 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Front-Panel Lights and Error Conditions Light Turns Off During Startup If Turns Off During Normal Operation If DS US The downstream receive channel cannot be acquired The downstream channel is lost The upstream send channel cannot be acquired The upstream channel is lost IP registration is unsuccessful The IP registration is lost The SBG940 is not properly plugged into the power outlet The SBG940 is unplugged Home Print X Exit 108 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Contact Us Configuration: Basic Gateway TCP/IP Wireless USB In the United States and Canada, if you need assistance while working with the SBG940 and related equipment supplied by Motorola:
If you rent or lease your SBG940 Contact your cable provider. If you own your SBG940 Call 1-877-466-8646 for technical and warranty support. Support is available 24 hours a day, seven days a week. For information about customer service, technical support, or warranty claims, see the Regulatory, Safety, Software License, and Warranty Information card provided with the SURFboard SBG940. For answers to typical questions, see Frequently-Asked Questions. For more information about Motorola consumer cable products, education, and support, visit http://broadband.motorola.com/consumers. Home Print X Exit 109 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Frequently-Asked Questions Here are answers to questions our customers frequently ask:
Q What is high-speed cable Internet access?
A Cable Internet access uses cable television wires instead of telephone lines to connect to the Internet. It is extremely fast and does not tie up telephone lines for incoming or outgoing calls and faxes. Q How fast is the Motorola SURFboard Cable Modem Gateway SBG940?
A Cable modems offer Internet access at speeds up to 100 times faster than a traditional phone modem. You can experience speeds of over 1,000 Kbps. Due to network condition such as traffic volume and the speed of the sites you visit, actual speed may vary. Many network and other factors can affect download speeds. Q How many users can one SBG940 support?
A A single SBG940 can support up to 253 users, each assigned a unique IP address, on a Class C network. Q What is Network Address Translation?
A NAT is a technique to translate private IP addresses on your LAN to a single IP address assigned by your cable provider that is that is visible to outside users on the Internet. Q What are IEEE 802.11g and IEEE 802.11b?
A They are IEEE wireless network standards. Q What type of firewall is provided on the SBG940?
A The SBG940 provides a stateful-inspection firewall. For more information, see Firewall and Setting the Firewall Policy. Q What wireless security measures are provided on the SBG940?
A To protect data transmitted over wireless connections, the SBG940 supports WPA or WEP encryption and MAC access control lists. For information, see Wireless Security and Setting Up Your Wireless LAN. Q Why is there no Standby button?
A As a security measure, current Motorola SURFboard cable modems provide a Standby button to temporarily suspend the Internet connection. Because enabling the SBG940 firewall provides high security levels while connected, the Standby button is not required. Q Can I still watch cable TV while using my SBG940?
A Yes, your cable TV line can carry the TV signal while you send and receive information on the Internet. Q What are CableLabs Certified, DOCSIS, and Euro-DOCSIS?
A CableLabs Certified, DOCSIS, and Euro-DOCSIS are the industry standards for high-speed data distribution over cable television system networks. They are intended to ensure that all compliant cable modems interface with all compliant cable systems. Your SBG940 is DOCSIS or Euro-DOCSIS certified. If I have an SBG940, can I still use my old 28.8 Kbps or 56 Kbps modem?
Q A Yes you can. However, once youve experienced the speed of cable Internet access, youll never again want to wait for traditional dial-up services. Home Print X Exit 110 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Q Do I need to change my Internet service provider (ISP)?
A Currently, most Internet service providers do not provide cable Internet access. Contact your cable company for your specific information. Q Do I need to subscribe to cable TV to get cable Internet access?
A No, but you will need to subscribe to cable Internet service. Some systems require that you subscribe to basic service before you can get Internet access and/or offer a discount when you use your own SBG940. Check with your local cable company for specific information. Q What type of technical support is available?
A For questions about your Internet service, connection, or SBG940, call your cable provider. Q What do I do if my SBG940 stops working?
A Troubleshooting provides tips to diagnose problems and simple solutions. If you continue to have problems, call your cable provider. Q Can multiple game players on the SBG940 LAN log onto the same game server and play simultaneously with just one public IP address?
It depends on the game server. For more information about gaming, see Gaming Configuration Guidelines. A Home Print X Exit 111 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Specifications Wireless Standards compliance IEEE 802.11g, IEEE 802.11b DSSS, IEEE 802.11g OFDM RF frequency range 2.412 to 2.462 GHz for North America 2.412 to 2.835 GHz for Japan Data rate Modulation 1 Mbps DBPSK 2 Mbps DQPSK 5.5 or 11 Mbps CCK 6, 9, 12, 18, 24, 36, 48, or 54 Mbps OFDM 1 Mbps DBPSK 2 Mbps DQPSK 5.5, 11 Mbps CCK 6, 9, 12, 18, 24, 36, 48, 54 Mbps OFDM Number of channels Europe = 13, Spain = 2, France = 4, US = 11, Japan = 14 Transmit power
+17 dBm (EIRP) Receive sensitivity
-65 dBm at 54 Mbps Router Ethernet standards compliance IEEE 802.3, IEEE 802.3u Routing protocol RIP V2 Number of uplink ports 4 Electrical Input voltage range 100 240 VAC, 50 60 Hz Power consumption 9 watts (nominal) Environmental Operating temperature 0 to 40 C, -150 to 10000 ft. Storage temperature
-30 to 80 C Humidity Antennas LED Indicators Interfaces Dimensions Weight 5 to 95% RH, non-condensing One external removable antenna, with a unique connector per FCC requirements One external adjustable non-removable antenna One Power, one Receive (DS), one Send (US), one Online, one Internet, one USB, one Wireless, and four Ethernet One AC power, one F-type, one USB Series B, and four RJ-45 290 mm (11.5 in.) wide x 160 mm (5.5 in.) deep x 70 mm (2.5 in) tall 1.8 lbs (unit only) Home Print X Exit 112 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Downstream Modulation Maximum data ratea Frequency range 64 or 256 QAM 38 Mbps 88 to 860 MHz (30 kHz minimum step size) Bandwidth 6 MHz Maximum symbol rate 5.069 Msym/s (64 QAM) 5.361 Msym/s (256 QAM) Operating level range
-15 to +15 dBmV Input impedance 75 ohms (nominal) Frequency range 88 to 860 MHz Upstream Modulation Modulation rate
(nominal) Maximum data ratec Bandwidth QPSK or 8b, 16, 32b, 64b, or 128b QAM TDMA: 160, 320, 640, 1280, 2560, and 5120 KHz S-CDMA: 1280, 2560, and 5120 KHz 30 Mbps TDMA: 200, 400, 800, 1600, 3200, and 6400b kHz S-CDMA: 1600, 3200, and 6400 kHz Symbol rates 160, 320, 640, 1280, and 2560 ksym/s Operating level range
(one channel) TDMA:
+8 to +54 dBmV (32 QAM, 64 QAM)
+8 to +55 dBmV (8 QAM, 16 QAM)
+8 to +58 dBmV (QPSK) S-CDMA:
+8 to +53 dBmV (all modulations) Output impedance 75 ohms nominal Frequency range 5 to 42 MHz (edge to edge) Output return loss
> 6 dB (5 to 42 MHz) General Cable interface F-Connector, female, 75 ohm CPE network interface USB, Ethernet 10/100Base-T (auto sensing) CPE wireless interface IEEE 802.11g Data protocol TCP/IP a. Actual speed will vary. Upload and download speeds are affected by several factors including, but not limited to network traffic and services provided by your cable provider, computer equipment, server type, number of connections to the server, and the availability of Internet routers. b. With a CMTS supporting A-TDMA or S-CDMA only. c. Actual speed will vary. Maximum speed of 30 Mbps is only attainable with A-TDMA or S-CDMA technology. Home Print X Exit 113 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Glossary This glossary defines terms and lists acronyms used with the SBG940. To return to your previous page, click the Acrobat Go to Previous View button. A access point adapter address translation ALG American Wire Gauge (AWG) ANSI ANX ARP ASCII asynchronous timing attenuation authentication authorization auto-MDIX A device that provides WLAN connectivity to wireless clients (stations). The SBG940 acts as a wireless access point. A device or card that connects a computer, printer, or other peripheral device to the network or to some other device. A wireless adapter connects a computer to the WLAN. See NAT. Application level gateway triggers are required by some file transfer (for example, FTP), game, and video conferencing applications to open one or more ports to enable the application to operate properly. A standard system used to designate the size of electrical conductors; gauge numbers are inverse to size. The American National Standards Institute is a non-profit, independent organization supported by trade organizations, industry, and professional societies for standards development in the United States. This organization defined ASCII and represents the United States to the International Organization for Standardization. Automotive Network Exchange Address Resolution Protocol broadcasts a datagram to obtain a response containing a MAC address corresponding to the host IP address. When it is first connected to the network, a client sends an ARP message. The SBG940 responds with a message containing its MAC address. Subsequently, data sent by the computer uses the SBG940 MAC address as its destination. The American Standard Code for Information Interchange refers to alphanumeric data for processing and communication compatibility among various devices; normally used for asynchronous transmission. The SBG940 uses synchronous timing for upstream data transmissions. The CMTS broadcasts messages that bandwidth is available. The SBG940 reserves data bytes requiring x-number of mini-slots. The CMTS replies that it can receive data at a specified time (synchronized). At the specified time, the SBG940 transmits the x-number of data bytes. The difference between transmitted and received power resulting from loss through equipment, transmission lines, or other devices; usually expressed in decibels. A process where the CMTS verifies that access is authorized, using a password, trusted IP address, or serial number. Part of the process between a CMTS and the cable modem or gateway to enable Baseline Privacy. Automatic medium-dependent interface crossover detects and corrects cabling errors by automatically reversing the send and receive pins on any port. It enables the use of straight-through wiring between the SBG940 Ethernet port and any computer, printer, or hub. To return to your previous page, click the Acrobat Go to Previous View button. Home Print X Exit 114 SBG940 User Guide B bandwidth Baseline Privacy baud BCP BER binary bit rate BPKM bps bridge broadband Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB The transmission capacity of a medium in terms of a range of frequencies. Greater bandwidth indicates the ability to transmit more data over a given period of time. An optional feature that encrypts data between the CMTS and the cable modem or gateway. Protection of service is provided by ensuring that a cable modem or gateway, uniquely identified by its MAC address, can only obtain keys for services it is authorized to access. The analog signaling rate. For complex modulation modes, the digital bit rate is encoded in multiple bits per baud, for example, 64 QAM encodes 6 bits per baud and 16 QAM encodes 4 bits per baud. Binary Communication Protocol The bit error rate is the ratio of the number of erroneous bits or characters received from some fixed number of bits transmitted. A numbering system that uses two digits, 0 and 1. The number of bits (digital 0s and 1s) transmitted per second in a communications channel. It is usually measured in bits per second bps. Baseline Protocol Key Management encrypts data flows between a cable modem or gateway and the CMTS. The encryption occurs after the cable modem or gateway registers to ensure data privacy across the RF network. bits per second An OSI layer 2 networking device that connects two LANs using similar protocols. It filters frames based on the MAC address to reduce the amount of traffic. A bridge can be placed between two groups of hosts that communicate a lot together, but not so much with the hosts in the other group. The bridge examines the destination of each packet to determine whether to transmit it to the other side. See also switch. High bandwidth network technology that multiplexes multiple, independent carriers to carry voice, video, data, and other interactive services over a single cable. A communications medium that can transmit a relatively large amount of data in a given time period. A frequently used synonym for cable TV that can describe any technology capable of delivering multiple channels and services. broadcast Simultaneous transmission to multiple network devices; a protocol mechanism supporting group and universal addressing. See also multicast and unicast. To return to your previous page, click the Acrobat Go to Previous View button. Home Print X Exit 115 SBG940 User Guide C CableHome Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB A project of CableLabs and technology suppliers to develop interface specifications for extending high-quality cable-based services to home network devices. It addresses issues such as device interoperability, QoS, and network management. CableHome will enable cable service providers to offer more services over HFC. It will improve consumer convenience by providing cable-delivered services throughout the home. CableLabs cable modem A research consortium that defines the interface requirements for cable modems and acknowledges that tested equipment complies with DOCSIS. A device installed at a subscriber location to provide data communications over an HFC network. Unless otherwise specified, all references to cable modem in this documentation refers to DOCSIS or Euro-DOCSIS cable modems only. File containing operational parameters that a cable modem or gateway downloads from the cable provider TFTP server during registration. cable modem configuration file circuit-switched Network-connection scheme used in the traditional PSTN telephone network where each connection requires a dedicated path for its duration. An alternative is packet-switched. Class C network An IP network containing up to 253 hosts. Class C IP addresses are in the form network.network.network.host. client CMTS CNR coaxial cable
(coax) CoS CPE In a client/server architecture, a client is a computer that requests files or services such as file transfer, remote login, or printing from the server. Also called a CPE. On a WLAN, a client is any host that can communicate with the access point. A wireless client is also called a station. A cable modem termination system is a device in the cable system headend that interfaces the HFC network to local or remote IP networks to connecting IP hosts, cable modems or gateways, and subscribers. It manages all cable modem bandwidth. It is sometimes called an edge router. carrier to noise ratio A type of cable consisting of a center wire surrounded by insulation and a grounded shield of braided wire. The shield minimizes electrical and radio frequency interference. Coaxial cable has high bandwidth and can support transmission over long distances. Class of service traffic management or scheduling functions are performed when transferring data upstream or downstream on HFC. Customer premise equipment, typically computers, printers, etc., are connected to the cable modem or gateway at the subscriber location. CPE can be provided by the subscriber or the cable provider. Also called a client. crosstalk CSMA/CD Undesired signal interfering with the desired signal. carrier sense multiple access with collision detection To return to your previous page, click the Acrobat Go to Previous View button. Home Print X Exit 116 SBG940 User Guide D datagram default route dB dBc DBm dBmV Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB In RFC 1594, a datagram is defined as a self-contained, independent entity of data carrying sufficient information to be routed from the source to the destination computer without reliance on earlier exchanges between this source and destination computer and the transporting network. For the most part, it has been replaced by the term packet. The route by which packets are forwarded when other routes in the routing table do not apply. decibel Signal level expressed in dB relative to the unmodulated carrier level desired. A unit of measurement referenced to one milliwatt across specified impedance. 0dBm = 1 milliwatt across 75 ohms. Signal level expressed in dB as the ratio of the signal power in a 75-ohm system to a reference power when 1 mV is across 75 ohms. demodulation An operation to restore a previously modulated wave and separate the multiple signals that were combined and modulated on a subcarrier. DHCP distortion DMZ DNS DOCSIS A Dynamic Host Configuration Protocol server dynamically assigns IP addresses to client hosts on an IP network. DHCP eliminates the need to manually assign static IP addresses by leasing an IP address and subnet mask to each client. It enables the automatic reuse of unused IP addresses:
The SBG940 is simultaneously a DHCP client and a DHCP server. A DHCP server at the cable system headend assigns a public IP address to the SBG940 and optionally to clients on the SBG940 LAN. The SBG940 contains a built-in DHCP server that assigns private IP addresses to clients. An undesired change in signal waveform within a transmission medium. A nonlinear reproduction of the input waveform. A de-militarized zone is one or more hosts logically located between a private LAN and the Internet. A DMZ prevents direct access by outside users to private data. (The term comes from the geographic buffers located between some conflicting countries such as North and South Korea.) In a typical small DMZ configuration, the DMZ host receives requests from private LAN users to access external web sites and initiates sessions for these requests. The DMZ host cannot initiate a session back to the private LAN. Internet users outside the private LAN can access only the DMZ host. You can use a DMZ to set up a web server or for gaming without exposing confidential data. The Domain Name System is the Internet system for converting domain names to IP addresses. A DNS server contains a table matching domain names such as Internetname.com to IP addresses such as 192.169.9.1. When you access the world-wide web, a DNS server translates the URL displayed on the browser to the destination website IP address. The DNS lookup table is a distributed Internet database; no one DNS server lists all domain name to IP address matches. The CableLabs Data-Over-Cable Service Interface Specification defines interface standards for cable modems, gateways, and supporting equipment to deliver data between an HFC network and a computer systems or television sets. To emphasize its use as a cable modem standard, DOCSIS is now called CableLabs Certified Cable Modems. Euro-DOCSIS is DOCSIS adapted for use in Europe. domain name A unique name, such as motorola.com, that maps to an IP address. Domain names are typically much easier to remember than are IP addresses. DSSS Direct Sequence Spread Spectrum To return to your previous page, click the Acrobat Go to Previous View button. Home Print X Exit 117 SBG940 User Guide dotted-decimal format download downstream driver DSL DSSS dynamic IP address E encapsulate encode encrypt endpoint ESSID Ethernet Euro-DOCSIS event expansion slot EAP Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Method of representing an IP address or subnet mask using four decimal numbers called octets. Each octet represents eight bits. In a class C IP address, the octets are network.network.network.host. The first three octets together represent the network address and the final octet is the host address. In the SBG940 LAN default configuration, 192.168.100 represents the network address. In the final octet, the host address can be from 2 to 254. To copy a file from one computer to another. You can use the Internet to download files from a server to a computer. A DOCSIS or Euro-DOCSIS cable modem or gateway downloads its configuration file from a TFTP server during start-up. In a cable data network, the direction of data received by the computer from the Internet. Software that enables a computer to interact with a network or other device. For example, there are drivers for printers, monitors, graphics adapters, modems, Ethernet, USB, HPNA, and many others. Digital Subscriber Line Direct Sequence Spread Spectrum is an IEEE 802.11b RF modulation protocol. An IP address that is temporarily leased to a host by a DHCP server. The opposite of static IP address. To include data into some other data unit to hide the format of the included data. To alter an electronic signal so that only an authorized user can unscramble it to view the information. To encode data. A VPN endpoint terminates the VPN at the router so that computers on the SBG940 LAN do not need VPN client software to tunnel through the Internet to the VPN server. The Extended Service Set Identifier or network name is a unique identifier that wireless clients use to associate with an access point to distinguish between multiple WLANs in the same area. All clients on a WLAN must have the same ESSID as the access point. On the SBG940, you can set the ESSID on the Wireless > NETWORK page. The most widely used LAN type, also known as IEEE 802.3. The most common Ethernet networks are 10Base-T, which provide transmission speeds up to 10 Mbps, usually over unshielded, twisted-pair wire terminated with RJ-45 connectors. Fast Ethernet (100Base-T) provides speeds up to 100 Mbps. Base means baseband technology and T means twisted pair cable. Each Ethernet port has a physical address called the MAC address. A tComLabs standard that is DOCSIS adapted for use in Europe A message generated by a device to inform an operator or the network management system that something has occurred. A connection point in a computer where a circuit board can be inserted to add new capabilities. Extensible Authentication Protocol To return to your previous page, click the Acrobat Go to Previous View button. Home Print X Exit 118 SBG940 User Guide F FCS F-type connector firewall flow FEC FDMA frame frequency FTP Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB frame check sequence A type of connector used to connect coaxial cable to equipment such as the SBG940. A security software system on the SBG940 that enforces an access control policy between the Internet and the SBG940 LAN. A data path moving in one direction. Forward error correction is a technique to correct transmission errors without requiring the transmitter to resend any data. Frequency Division Multiple Access is a method to allow multiple users to share a specific radio spectrum. Each active user is assigned an individual RF channel (or carrier) with the carrier frequency of each channel offset from its adjacent channels by an amount equal to the channel spacing, which allows the required bandwidth per channel. A unit of data transmitted between network nodes that contains addressing and protocol control data. Some control frames contain no data. Number of times an electromagnetic signal repeats an identical cycle in a unit of time, usually one second, measured in Hz, kHz, MHz, or GHz. File Transfer Protocol is a standard Internet protocol for exchanging files between computers. FTP is commonly used to download programs and other files to a computer from web pages on Internet servers. full-duplex The ability to simultaneously transmit and receive data. See also half-duplex. G gain gateway gateway IP address GHz GUI The extent to which a signal is boosted. A high gain antenna increases the wireless signal level to increase the distance the signal can travel and remain usable. A device that enables communication between networks using different protocols. See also router. The SBG940 enables up to 253 computers supporting IEEE 802.11b, Ethernet, or USB to share a single broadband Internet connection. The address of the default gateway router on the Internet. Also known as the giaddr. Gigahertz one billion cycles per second. graphical user interface To return to your previous page, click the Acrobat Go to Previous View button. Home Print X Exit 119 SBG940 User Guide H H.323 half-duplex headend header hexadecimal HFC hop host HTML hub Hz Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB A suite of protocols created by the ITU for interactive video-conferencing, data sharing, and audio applications such as VoIP. Network where only one device at a time can transmit data. See also full-duplex. A location that receives TV programming, radio programming, data, and telephone calls that it modulates onto the HFC network. It also sends return data and telephone transmissions. Headend equipment includes transmitters, preamplifiers, frequency terminals, demodulators, modulators, and other devices that amplify, filter, and convert incoming broadcast TV signals to wireless and cable channels. The data at the beginning of a packet that identifies what is in the packet. A base-sixteen numbering system that uses sixteen sequential numbers (0 to 9 and the letters A to F) as base units before adding a new position. On computers, hexadecimal is a convenient way to express binary numbers. A hybrid fiber/coaxial cable network uses fiber-optic cable as the trunk and coaxial cable to the subscriber premises. The interval between two routers on an IP network. The number of hops a packet traverses toward its destination (called the hop count) is saved in the packet header. For example, a hop count of six means the packet has traversed six routers. The packet hop count increases as the time-to-live (TTL) value decreases. In IP, a host is any computer supporting end-user applications or services with full two-way network access. Each host has a unique host number that combined with the network number forms its IP address. Host also can mean:
A computer running a web server that serves pages for one or more web sites belonging to organization(s) or individuals A company that provides this service In IBM environments, a mainframe computer Hyper Text Markup Language On a LAN, a hub is a device that connects multiple hosts to the LAN. A hub performs no data filtering. See also bridge and router. An IP hub is typically a unit on a rack or desktop. On an HFC network, a hub is a scaled-down headend that performs some or all headend functions for part of the system. Hertz one cycle per second. The unit to measure the frequency that an alternating electromagnetic signal cycles through its highest and lowest states. Used to define the bands of the electromagnetic spectrum used in voice and data communications, or to define the bandwidth of a transmission medium. To return to your previous page, click the Acrobat Go to Previous View button. Home Print X Exit 120 SBG940 User Guide I IANA ICMP ICSA IEEE IEEE 802.11b IEEE 802.11g IEEE 802.3 IETF IGMP IGMP spoofing impedance impulse noise ingress noise Internet Internetwork IP Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB The Internet Numbering Address Authority (IANA) is an organization under the Internet Architecture Board (IAB) of the Internet Society that oversees IP address allocation. It is under a contract from the U.S. government. Internet Control Message Protocol is a protocol used for error, problem, and informational messages sent between IP hosts and gateways. ICMP messages are processed by the IP software and are not usually apparent to the end-user. The International Computer Security Association is the security industrys main source of research, intelligence, and product certification. The Institute of Electrical and Electronics Engineers, Inc. (http://www.ieee.org) is an organization that produces standards, technical papers, and symposiums for the electrical and electronic industries and is accredited by ANSI. IEEE wireless network standards. See Ethernet. The Internet Engineering Task Force (http://www.ietf.org) is an open international community of network designers, operators, vendors, and researchers to develop and maintain Internet architecture. Technical working groups issue working documents called Internet-Drafts. The IETF publishes review versions of the drafts called requests for comments (RFCs). Internet Group Membership Protocol the Internet multicasting standard. IGMP establishes and maintains a database of group multicast addresses and interfaces to which a multicast router forwards multicast packets. IGMP runs between multicast hosts and their immediately-neighboring multicast routers. A process where a router acts as an IGMP querier for multicast hosts and an IGMP host to a multicast router. The total opposition to AC electron current flow within a device. Impedance is typically 75 ohms for coax cable and other CATV components. Noise of very short in duration, typically of the order of 10 microseconds. It is caused by electrical transients such as voltage spikes, electric motors turning on, and lightning or switching equipment that bleed over to the cable. Noise typically caused by discrete frequencies picked up by the cable plant from radio broadcasts or an improperly grounded or shielded home appliance such as a hair dryer. Ingress is the major source of cable system noise. A worldwide collection of interconnected networks using TCP/IP. A collection of interconnected networks allowing communication between all devices connected to any network in the collection. Internet Protocol is a set of standards that enable different types of computers to communicate with one another and exchange data through the Internet. IP provides the appearance of a single, seamless communication system and makes the Internet a virtual network. To return to your previous page, click the Acrobat Go to Previous View button. Home Print X Exit 121 SBG940 User Guide IP address IPSec IKE ISAKMP ISDN ISO ISP ITU K kHz Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB A unique 32-bit value that identifies each host on a TCP/IP network. TCP/IP networks route messages based on the destination IP address. An IP address has two parts:
The network address is assigned by IANA. The SBG940 network administrator assigns a host address to each host connected to the SBG940, automatically using its DHCP server or as a static IP address. For a Class C network, the first 24 bits are the network address and the final 8 bits are the host address; in dotted-decimal format it appears network.network.network.host. If you enable the SBG940 DHCP client on the WAN page, the cable provider automatically assigns the network address, subnet mask, domain name, and DNS server to provide a continuous Internet connection. The Internet Protocol Security protocols are IETF authentication and encryption standards for secure packet exchange over the Internet. IPSec works at OSI layer 3 and secures everything on the network. Internet Key Exchange Internet Security Association and Key Management Protocol Integrated Services Digital Network The International Organization for Standardization (http://www.iso.ch) is a worldwide federation of national standards bodies from approximately 140 countries. ISO is a non-governmental organization established in 1947 to promote the development of standardization and related activities in the world with a view to facilitating the international exchange of goods and services, and to developing cooperation in the spheres of intellectual, scientific, technological, and economic activity. Internet Service Provider International Telecommunications Union kilohertz one thousand cycles per second To return to your previous page, click the Acrobat Go to Previous View button. Home Print X Exit 122 SBG940 User Guide L L2F L2TP LAC LAN layer LCP latency LED LNS Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Layer 2 Forwarding is an OSI layer 2 protocol that establishes a secure tunnel across the Internet to create a virtual PPP connection between the user and the enterprise network. L2F is the most established and stable layer 2 tunneling protocol. Layer 2 Tunnel Protocol is a PPP extension that enables ISPs to operate VPNs. L2TP merges the best features of the PPTP and L2F. L2TP is the emerging IETF standard. An L2TP access concentrator is a device to which the client directly connects through which PPP frames are tunneled to the LNS. The LAC need only implement the media over which L2TP operates to transmit traffic to one or more LNSs. The LAC may tunnel any protocol carried within PPP. The LAC initiates incoming calls and receives outgoing calls. A LAC is analogous to an L2F NAS. A local area network provides a full-time, high-bandwidth connection over a limited area, such as a building or campus. Ethernet is the most widely used LAN standard. In networks, layers are software protocol levels. Each layer performs functions for the layers above it. OSI is a reference model having seven functional layers. Link Control Protocol establishes, configures, and tests data link connections used by PPP. The time required for a signal to pass through a device. It is often expressed in a quantity of symbols. light-emitting diode An L2TP network server is a termination point for L2TP tunnels where PPP frames are processed and passed to higher layer protocols. An LNS can operate on any platform that terminates PPP. The LNS handles the server side of the L2TP protocol. L2TP relies only on the single media over which L2TP tunnels arrive. The LNS can have a single LAN or WAN interface but can terminate calls arriving at any of the LACs full range of PPP interfaces (asynchronous, synchronous, ISDN, V.120, etc.). The LNS initiates outgoing calls and receives incoming calls. An LNS is analogous to a home gateway in L2F technology. loopback A test that loops the transmit signal to the receive signal. Usually the loopback test is initiated on a network device. The test is used to verify a path or to measure the quality of a signal on that path. To return to your previous page, click the Acrobat Go to Previous View button. Home Print X Exit 123 SBG940 User Guide M MAC address MB Mbps media MIB MHz MPDU MSDU MSO MTU multicast mW Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB The Media Access Control address is a unique, 48-bit value permanently saved in ROM at the factory to identify each Ethernet network device. It is expressed as a sequence of 12 hexadecimal digits printed on a Label on the Bottom of the SBG940. You need to provide the HFC MAC address to the cable provider. Also called an Ethernet address, physical address, hardware address, or NIC address. One megabyte; equals 1,024 x 1,024 bytes, 1,024 kilobytes, or about 8 million bits. Million bits per second (megabits per second). A rate of data transfer. The various physical environments through which signals pass; for example, coaxial, unshielded twisted-pair (UTP), or fiber-optic cable. A management information base is a unique hierarchical structure of software objects used by the SNMP manager and agent to configure, monitor, or test a device. Megahertz one million cycles per second. A measure of radio frequency. MAC protocol data unit (PDU) MAC service data unit Multiple Systems Operator. A company that owns and operates more than one cable system. Also called a group operator. The Maximum Transmission Unit is the largest amount of data that can be transmitted in one discrete message on a given physical network. The MTU places an upper bound on the size of a message that can be transferred by the network in a single frame. Messages exceeding the MTU must be fragmented before transmission, and reassembled at the destination. A data transmission sent from one sender to multiple receivers. See also broadcast and unicast. milliwatts To return to your previous page, click the Acrobat Go to Previous View button. Home Print X Exit 124 SBG940 User Guide N NAS NAT NAPT NEC network network driver network layer NIC node noise O ohm OSI Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB network access server Network Address Translation is an Internet standard for a LAN to use one set of IP addresses for internal traffic and a second set of IP addresses for external traffic. NAT provides some security because the IP addresses of SBG940 LAN computers are invisible on the Internet. If NAT is enabled on the Gateway page, there is a one-to-one mapping between each public IP address and client IP address. Network Address Port Translation is the most common form of address translation between public and private IP addresses. NAPT is a mapping of one public IP address to many private IP addresses. If NAPT is enabled on the Gateway page, one public IP address is mapped to an individual private IP address for up to 245 LAN clients. National Electrical Code (United States) The regulations for construction and installation of electrical wiring and apparatus, suitable for mandatory application by a wide range of state and local authorities. Two or more computers connected to communicate with each other. Networks have traditionally been connected using some kind of wiring. Software packaged with a NIC that enables the computer to communicate with the NIC. Layer 3 in the OSI architecture that provides services to establish a path between open systems. The network layer knows the address of the neighboring nodes, packages output with the correct network address data, selects routes, and recognizes and forwards to the transport layer incoming messages for local host domains. A network interface card converts computer data to serial data in a packet format that it sends over the LAN. A NIC is installed in an expansion slot or can be built-in. Every Ethernet NIC has a MAC address permanently saved in its ROM. On a LAN, a generic term for any network device. On an HFC network, the interface between the fiber-optic trunk and coaxial cable feeders to subscriber locations. A node is typically located in the subscriber neighborhood. Random spurts of electrical energy or interface. May produce a salt-and-pepper pattern on a television picture. A unit of electrical resistance. The Open Systems Interconnection reference model is an illustrative model describing how data moves from an application on the source host through a network to an application on the destination host. It is a conceptual framework developed by ISO that is now the primary model for intercomputer communications. OSI is a model only; it does not define a specific networking interface. To return to your previous page, click the Acrobat Go to Previous View button. Home Print X Exit 125 SBG940 User Guide P packet packet-
switched PacketCable Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB The unit of data that is routed between the sender and destination on the Internet or other packet-switched network. When data such as an e-mail message or other file is sent over the Internet, IP on the sender divides the data into uniquely-numbered packets. The packet header contains the source and destination IP addresses. The individual packets may travel different routes. When all packets arrive at the destination, IP at that end reassembles the packets. The header and the data can vary in length. Packet and datagram are similar in meaning. A scheme to handle transmissions on a connectionless network such as the Internet. An alternative is circuit-switched. A CableLabs-led project to define a common platform to deliver advanced real-time multimedia services over two-way HFC cable plant. Built on DOCSIS 1.1, PacketCable networks use IP technology as the basis for a highly-capable multimedia architecture. pass-through A pass-through client on the SBG940 LAN obtains its public IP address from the cable provider DHCP server. PAT PCI PCMCIA PDA PDU periodic ranging physical layer Port Address Translation The Personal Computer Memory Card International Association sets international standards for connecting peripherals to portable computers. Laptop computers typically have a PCMCIA slot that can hold one or two PC Cards to provide features such as Ethernet connectivity. personal desktop assistant A protocol data unit is a message containing operational instructions used for SNMP. The basic SNMP V2 PDU types are get-request, get-next-request, get-bulk-request, response, set-request, inform-request, and trap. Ranging that is performed on an on-going basis after initial ranging has taken place. Layer 1 in the OSI architecture. It provides services to transmit bits or groups of bits over a transmission link between open systems. It entails the electrical, mechanical, and handshaking procedures. piggybacking A process that occurs when a cable modem simultaneously transmits data and requests additional bandwidth. PING PMD point-to-point POTS port A network utility that tests host reachability by sending a small packet to the host and waiting for a reply. If you PING a computer IP address and receive a reply, you know the computer is reachable over the network. It also stands for Packet InterNet Groper. The physical media-dependent sublayer of the physical layer which transmits bits or groups of bits over particular types of transmission links between open systems. It entails the electrical, mechanical, and handshaking procedures. Physical connection made from one point to another. The plain old telephone service offered through the PSTN; basic analog telephone service. POTS uses the lowest 4 kHz of bandwidth on twisted pair wiring. On a computer or other electronic device, a port is a socket or plug used to physically connect it to the network or to other devices. in TCP/IP, a port is a number from 0 to 65536 used logically by a client program to specify a server program. Ports 0 to 1024 are reserved To return to your previous page, click the Acrobat Go to Previous View button. Home Print X Exit 126 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB port mirroring A feature that enables one port (source) on the SBG940 to be copied to another port (destination) to be studied. The destination mirrors the transmitted (from) or received (to) data on the source port to enable the person managing the network to monitor activity. port triggering A mechanism that allows incoming communication with specified applications. Primarily used for gaming applications. PPP PPTP private IP address protocol provisioning PSTN Point-to-Point Protocol is used to transport other protocols, typically for simple links over serial lines. It is most commonly used to access the Internet with a dial-up modem. Point-to-Point Tunneling Protocol encapsulates other protocols. It is a new technology to create VPNs developed jointly by several vendors. An IP address assigned to a computer on the SBG940 LAN by the DHCP server on the SBG940 for a specified lease time. Private IP addresses are used by the SBG940 LAN only; they are invisible to devices on the Internet. See also public IP address. A formal set of rules and conventions for exchanging data. Different computer types (for example PC, UNIX, or mainframe) can communicate if they support common protocols. The process of autodiscovery or manually configuring a cable modem on the CMTS. The public switched telephone network is the traditional circuit-switched, voice-oriented telephone network. See also POTS. public IP address The IP address assigned to the SBG940 by the cable provider. A public IP address is visible to devices on the Internet. See also private IP address. Q QAM QPSK QoS Quadrature Amplitude Modulation uses amplitude and phase modulation to encode multiple bits of data in one signaling element. QAM achieves faster data transfer than amplitude or phase modulation alone, but the signal is more prone to errors caused by noise. QAM requires a transmission circuit with a higher CNR than alternate modulation formats such as QPSK. Two types of QAM are:
16 QAM encodes four bits per symbol as one of 16 possible amplitude and phase combinations. 64 QAM encodes six bits per symbol as one of 64 possible amplitude and phase combinations. Quadrature Phase Shift Key (QPSK) modulation sends two bits of information per symbol period with one symbol 90 degrees out of phase with other symbols. The four constellation points represented by the coordinates (0,0 - 0,1 - 1,0 - 1,1) represent the four possible combinations. Quality of service describes the priority, delay, throughput, and bandwidth of a connection. To return to your previous page, click the Acrobat Go to Previous View button. Home Print X Exit 127 SBG940 User Guide R RADIUS RAS registration return loss RF RFC RJ-11 RJ-45 ROM router routing table RTS Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Remote Authentication Dial-In User Service server typically used in large corporate settings. Remote Access Server How a cable modem makes itself known to the CMTS. The cable modem configuration file and authorization are verified and the CoS is negotiated. A measurement of the quality of the match of the device to the cable system. Return loss is the ratio of the amount of power reflected by the device. A return loss of 20 dB or greater is preferred. Radio Frequency signals used by the CMTS transmitter and receiver to send data over HFC. The carrier is modulated to encode the digital data stream for transmission across the cable network. Request for Comments published on the IETF or other websites. Many RFCs become international standards. The most common type of connector for household or office phones. An 8-pin modular connector; the most common connector type for 10Base-T or 100Base-T Ethernet networks. read-only memory On IP networks, a device connecting at least two networks, which may or may not be similar. A router is typically located at a gateway between networks. A router operates on OSI network layer 3. It filters packets based on the IP address, examining the source and destination IP addresses to determine the best route on which to forward them. A router is often included as part of a network switch. A router can also be implemented as software on a computer. A table listing available routes that is used by a router to determine the best route for a packet. request to send To return to your previous page, click the Acrobat Go to Previous View button. Home Print X Exit 128 SBG940 User Guide S server Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB In a client/server architecture, a dedicated computer that supplies files or services such as file transfer, remote login, or printing to clients. The set of IP addresses that a DHCP server can lease to clients. scope service provider A company providing cable data services to subscribers. SID A service ID is a unique 14-bit identifier the CMTS assigns to a cable modem or gateway that identifies the traffic type it carries (for example, data or voice). The SID provides the basis for the CMTS to allocate bandwidth to the cable modem and implement CoS. SDU SME SMTP SNMP SOHO spectrum spectrum allocation splitter stateful inspection static filter static IP address static route station subscriber subnet mask subnetwork service data unit small and medium enterprise Simple Mail Transfer Protocol is a standard Internet protocol for transferring e-mail. Simple Network Management Protocol is a standard to monitor and manage networks and network devices. Data is exchanged using PDU messages. small office home office A specified range of frequencies used for transmission of electromagnetic signals. An allocation of portions of the available electromagnetic spectrum for specific services, such as AM, FM, or personal communications. A device that divides the signal from an input cable between two or more cables. A type of firewall that tracks each connection traversing all firewall interfaces to ensure validity. In addition to examining the source and destination in the packet header based on static rules, a stateful inspection firewall:
Examines packet headers on context established by previous packets that traversed the firewall Monitors the connection state and saves it in a table Closes ports until a connection to a specific port is requested May examine the packet contents up through the application layer to determine more than just the source and destination A stateful-inspection firewall is more advanced than a static filter firewall. A type of firewall that examines the source and destination in the packet header based on administrator-defined rules only. An IP address that is permanently assigned to a host. Normally, a static IP address must be assigned manually. The opposite of dynamic IP address. A manually-defined route. IEEE 802.11b term for wireless client. A home or office user who accesses television, data, or other services from a cable provider. A bit mask that is logically ANDed with the destination IP address of a packet to determine the network address. A router routes packets using the network address. A part of a network; commonly abbreviated subnet. When subnetting is used, the host portion of the IP address is divided into a subnet and host number. Hosts and routers use the subnet mask to identify the bits used for the network and subnet number. To return to your previous page, click the Acrobat Go to Previous View button. Home Print X Exit 129 SBG940 User Guide switch symbol rate Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB On an Ethernet network, a switch filters frames based on the MAC address, in a manner similar to a bridge. A switch is more advanced because it can connect more than two segments. Also known as baud rate, is a measure of the number of times per second a signal in a communications channel varies, or makes a transition between states (states being frequencies, voltage levels or phase angles). Usually measured in symbols per second (sps). SYSLOG A de-facto UNIX standard for logging system events. T TBCP TCP TCP/IP TFTP TKIP transparent bridging transport layer trunk TTL tunnel Tagged Binary Communication Protocol Transmission Control Protocol on OSI transport layer four, provides reliable transport over the network for data transmitted using IP (network layer three). It is an end-to-end protocol defining rules and procedures for data exchange between hosts on top of connectionless IP. TCP uses a timer to track outstanding packets, checks error in incoming packets, and retransmits packets if requested. The Transmission Control Protocol/Internet Protocol suite provides standards and rules for data communication between networks on the Internet. It is the worldwide internetworking standard and the basic communications protocol of the Internet. Trivial File Transfer Protocol is a very simple protocol used to transfer files. Temporal Key Integrity Protocol A method to enable all hosts on the wired Ethernet LAN, WLAN, and USB connection to communicate as if they were all connected to the same physical network. Layer of the OSI concerned with protocols for error recognition and recovery. This layer also regulates information flow. Electronic path over which date is transmitted. The time to live is the number of routers (or hops) a packet can traverse before being discarded. When a router processes a packet, it decreases the TTL by 1. When the TTL reaches zero, the packet is discarded. To place packets inside other packets to send over a network. The protocol of the enclosing packet is understood by each endpoint, or tunnel interface, where the packet enters and exits the network. VPNs rely on tunneling to create a secure network. Tunneling requires the following protocol types:
A carrier protocol, such as TCP, used by the network that the data travels over An encapsulating protocol, such as IPSec, L2F, L2TP, or PPTP, that is wrapped around the original data A passenger protocol, such as IP, for the original data two-way A cable system that can transmit signals in both directions to and from the headend and the subscriber. To return to your previous page, click the Acrobat Go to Previous View button. Home Print X Exit 130 SBG940 User Guide U-Z UDP unicast upstream USB UTP VLAN VoIP VPN WAN WAP WECA WEP Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB User Datagram Protocol A point-to-point data transmission sent from one sender to one receiver. This the normal way you access websites. See also broadcast and multicast. In a cable data network, upstream describes the direction of data sent from the subscriber computer through the cable modem to the CMTS and the Internet. Universal Serial Bus is a computer interface for add-on devices such as printers, scanners, mice, modems, or keyboards. USB supports data transfer rates of 12 Mbps and plug-and-play installation. You can connect up to 127 devices to a single USB port. unshielded twisted pair (wire) A virtual local area network is group of devices on different LAN segments that are logically configured to communicate as if they are connected to the same wire. Voice over Internet Protocol is a method to exchange voice, fax, and other information over the Internet. Voice and fax have traditionally been carried over traditional telephone lines of the PSTN using a dedicated circuit for each line. VoIP enables calls to travel as discrete data packets on shared lines. VoIP is an important part of the convergence of computers, telephones, and television into a single integrated information network. A virtual private network is a private network that uses virtual connections (tunnels) routed over a public network (usually the Internet) to provide a secure and fast connection; usually to users working remotely at home or in small branch offices. A VPN connection provides security and performance similar to a dedicated link (for example, a leased line), but at much lower cost. A wide-area network provides a connection over a large geographic area, such as a country or the whole world. The bandwidth depends on need and cost, but is usually much lower than for a LAN. Wireless access point or Wireless Access Protocol. See also access point. The Wireless Ethernet Compatibility Alliance is a trade organization that works to ensure that all wireless devices computer cards, laptops, air routers, PDAs, etc can communicate with each other. Wired Equivalent Privacy encryption protects the privacy of data transmitted over a WLAN. WEP uses keys to encrypt and decrypt transmitted data. The access point must authenticate a client before it can transfer data to another client. WEP is part of IEEE 802.11b. Because WEP can be difficult to use and does not provide very strong encryption, we recommend using WPA if possible. Wireless fidelity (pronounced y-phi) brand name applied to products supporting IEEE 802.11b. The Motorola SURFboard Wireless Cable Modem Gateway is a single device that combines a cable modem, router, Ethernet switch, wireless access point, and DHCP server for SOHO or SME use. WiFi Wireless Cable Modem Gateway WLAN world wide web An interface to the Internet that you use to navigate and hyperlink to information. WPA Wi-Fi Protected Access (WPA) encryption, as described on the Wi-Fi Alliance Wi-Fi Protected Access web page http://www.wifialliance.org/OpenSection/protected_access.asp). It is a far more robust form of encryption than WEP. We recommend using WPA if all of your client hardware supports WPA. wireless LAN To return to your previous page, click the Acrobat Go to Previous View button. Home Print X Exit 131 SBG940 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Software License Motorola, Inc., Broadband Communications Sector (Motorola), 101 Tournament Drive, Horsham, PA 19044 IMPORTANT: PLEASE READ THIS SOFTWARE LICENSE (LICENSE) CAREFULLY BEFORE YOU INSTALL, DOWNLOAD OR USE ANY APPLICATION SOFTWARE, USB DRIVER SOFTWARE, FIRMWARE AND RELATED DOCUMENTATION (SOFTWARE) PROVIDED WITH MOTOROLAS CABLE DATA PRODUCT (THE CABLE DATA PRODUCT). BY USING THE CABLE DATA PRODUCT AND/OR INSTALLING, DOWNLOADING OR USING ANY OF THE SOFTWARE, YOU INDICATE YOUR ACCEPTANCE OF EACH OF THE TERMS OF THIS LICENSE. UPON ACCEPTANCE, THIS LICENSE WILL BE A LEGALLY BINDING AGREEMENT BETWEEN YOU AND MOTOROLA. THE TERMS OF THIS LICENSE APPLY TO YOU AND TO ANY SUBSEQUENT USER OF THIS SOFTWARE. IF YOU DO NOT AGREE TO ALL OF THE TERMS OF THIS LICENSE (I) DO NOT INSTALL OR USE THE SOFTWARE AND (II) RETURN THE CABLE DATA PRODUCT AND THE SOFTWARE (COLLECTIVELY, PRODUCT), INCLUDING ALL COMPONENTS, DOCUMENTATION AND ANY OTHER MATERIALS PROVIDED WITH THE PRODUCT, TO YOUR POINT OF PURCHASE OR SERVICE PROVIDER, AS THE CASE MAY BE, FOR A FULL REFUND. The Software includes associated media, any printed materials, and any on-line or electronic documentation, as well as any updates, revisions, bug fixes, or drives obtained by you from Motorola or your service provider. Software provided by third parties may be subject to separate end-user license agreements from the manufacturers of such Software. The Software is never sold. Motorola licenses the Software to the original customer and to any subsequent licensee for personal use only on the terms of this License. Motorola and its 3rd party licensors retain the ownership of the Software. You may:
USE the Software only in connection with the operation of the Product. TRANSFER the Software (including all component parts and printed materials) permanently to another person, but only if the person agrees to accept all of the terms of this License. If you transfer the Software, you must at the same time transfer the Product and all copies of the Software (if applicable) to the same person or destroy any copies not transferred. TERMINATE this License by destroying the original and all copies of the Software (if applicable) in whatever form. You may not:
(1) Loan, distribute, rent, lease, give, sublicense or otherwise transfer the Software, in whole or in part, to any other person, except as permitted under the TRANSFER paragraph above. (2) Copy or translate the User Guide included with the Software, other than for personal use. (3) Copy, alter, translate, decompile, disassemble or reverse engineer the Software, including but not limited to, modifying the Software to make it operate on non-compatible hardware. (4) Remove, alter or cause not to be displayed, any copyright notices or startup message contained in the Software programs or documentation. (5) Export the Software or the Product components in violation of any United States export laws. The Product is not designed or intended for use in on-line control of aircraft, air traffic, aircraft navigation or aircraft communications; or in design, construction, operation or maintenance of any nuclear facility. MOTOROLA AND ITS 3RD PARTY LICENSORS DISCLAIM ANY EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR SUCH USES. YOU REPRESENT AND WARRANT THAT YOU SHALL NOT USE THE PRODUCT FOR SUCH PURPOSES. Title to this Software, including the ownership of all copyrights, mask work rights, patents, trademarks and all other intellectual property rights subsisting in the foregoing, and all adaptations to and modifications of the foregoing shall at all times remain with Motorola and its 3rd party licensors. Motorola retains all rights not expressly licensed under this License. The Software, including any images, graphics, photographs, animation, video, audio, music and text incorporated therein is owned by Motorola or its 3rd party licensors and is protected by United States copyright laws and international treaty provisions. Except as otherwise expressly provided in this License, the copying, reproduction, distribution or preparation of derivative works of the Software, any portion of the Product or the documentation is strictly prohibited by such laws and treaty provisions. Nothing in this License constitutes a waiver of Motorolas rights under United States copyright law. This License and your rights regarding any matter it addresses are governed by the laws of the Commonwealth of Pennsylvania, without reference to conflict of laws principles. THIS LICENSE SHALL TERMINATE AUTOMATICALLY if you fail to comply with the terms of this License. Motorola is not responsible for any third party software provided as a bundled application, or otherwise, with the Software. U.S. GOVERNMENT RESTRICTED RIGHTS The Product and documentation is provided with RESTRICTED RIGHTS. The use, duplication or disclosure by the Government is subject to restrictions as set forth in subdivision (c)(1)(ii) of The Rights in Technical Data and Computer Software clause at 52.227-7013. The contractor/manufacturer is Motorola, Inc., Broadband Communications Sector, 101 Tournament Drive, Horsham, PA 19044. Home Print X Exit 132 SBG940 User Guide Visit our website at:
www.motorola.com 512661-001 2/04 MGBI
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2004-03-19 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2004-03-19
|
||||
1 | Applicant's complete, legal business name |
Motorola Mobility LLC
|
||||
1 | FCC Registration Number (FRN) |
0004321311
|
||||
1 | Physical Address |
Motorola Mobility LLC
|
||||
1 |
Chicago, Illinois 60654
|
|||||
1 |
United States
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
k******@emcc.de
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
IHD
|
||||
1 | Equipment Product Code |
SBG940-1
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
J****** N******
|
||||
1 | Title |
Director Product Compliance
|
||||
1 | Telephone Number |
847-6********
|
||||
1 | Fax Number |
847-6********
|
||||
1 |
n******@motorola.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DTS - Digital Transmission System | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Wireless Cable Modem Gateway | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Power output listed is conducted. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
ECOM Sertech Corp.
|
||||
1 | Name |
C**** W******
|
||||
1 | Telephone Number |
88635********
|
||||
1 | Fax Number |
88635********
|
||||
1 |
c******@itri.org.tw
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | CE | 2412.00000000 | 2462.00000000 | 0.0295100 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC