FCC ID: VPYLB2BP Communication Module

LBUA0VG2BP User Manual for FCC FCC ID:VPYLB2BP Since this module is not sold to general end users directly, there is no user manual of module. For the details about this module, please refer to the specification sheet of module. This module should be installed in the host device according to the interface specification

(installation procedure). Warning;

CFR 15.521(a) notice This module may not be employed for the operation of toys. Operation onboard aircraft, ship or satellite is prohibited. CFR 15.519 a(2) notice The use of antennas mounted on outdoor structures, e.g., antennas mounted on the outside of a building or on a telephone pole, or any fixed outdoors infrastructure is prohibited. Antennas may be mounted only on the hand held UWB device. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 03 August 2022 1 LBUA0VG2BP User Manual for FCC This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with below part 15 of FCC Rules. Part 15 Subpart F The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module, This module has been evaluated stand alone to meet portable use without restriction, however, if a host product also contains other transmitter(s) and antenna(s), necessary test or evaluation needs to be performed in order to meet the requirement. Antenna Change Notice to Host manufacturer If you desire to increase antenna gain and either change antenna type or use same antenna type certified, a Class II permissive change application is required to be filed by us, or you(host manufacturer) can take responsibility through the change in FCC ID(new application) procedure followed by a Class II permissive change application. This module needs to supply a regulated voltage from host device. VDD_1V8_DIG: 1.71~1.98V VDD_1V8_RF: 1.71~1.98V Since there is no space which indicates FCC ID on this module, FCC ID is indicated in a manual. If the FCC ID is not visible when the module is installed inside another device, then the module is installed must also display a label referring to the enclosed module. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 03 August 2022 2 LBUA0VG2BP User Manual for FCC Maker P/N Type Gain [dBi]

5ch 9ch Appearance Supported Antenna Murata MTD-ANT-027-1-A_UWB_ANT18mm Patch 0.9 2.7 Copyright Murata Manufacturing Co., Ltd. All rights reserved. 03 August 2022 3 LBUA0VG2BP User Manual for FCC The following statements must be described on the user manual of the host device of this module;

Contains Transmitter Module FCC ID:VPYLB2BP or Contains FCC ID: VPYLB2BP This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

*If it is difficult to describe this statement on the host product due to the size, please describe in the User's manual. FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 03 August 2022 4 LBUA0VG2BP Operational Description FCC ID of this product is as follows. FCC ID: VPYLB2BP Contents 1.PIN Layout 2.Supply Voltage 3.Power Levels 4.Theory of operation 5. Antenna Copyright Murata Manufacturing Co., Ltd. All rights reserved. 03 August 2022 5 1.PIN Layout Top View No. 1 2 3 4 5 6 7 8 9 10 11 12 Terminal Name GND SE_2 SE_1 GPIO05_SENS ORINT GND XTAL2_32K XTAL1_32K GND SWD_CLK SWD_IO GND GND No. 13 14 15 16 17 18 19 20 21 22 23 24 Terminal Name ANT0 GND GND ANT1 GND GND GND ANT2 GND GND GPIO11 GPIO14 No. 25 26 27 28 Terminal Name HOST_4 HOST_1 HOST_2 HOST_3 GND VDD_1V8_RF VDD_1V8_DIG GND 29 30 31 32 33 GPIO03_SYNC CHIPENABLE 34 RTC_SYNC 35 GPIO08 36 No. 37 38 39 40 41 42 43 44 45 46 Terminal Name COEX_2 COEX_1 UART2_TX UART2_RX GND GND GND GND GND GND Copyright Murata Manufacturing Co., Ltd. All rights reserved. 03 August 2022 6 2.Supply Voltage DUT PIN Name VDD_1V8_DIG VDD_1V8_RF Min. 1.71 1.71 Typ. 1.80 1.80 Max. 1.98 1.98 unit V V 3. Power Levels Modulation Channel MAXIMUM TUNE UP TOLERANCE Peak Power Average Power BPM-BPSK BPSK 5, 9 5, 9 0dBm/50MHz 0dBm/50MHz

-41.3dBm/MHz

-41.3dBm/MHz Copyright Murata Manufacturing Co., Ltd. All rights reserved. 03 August 2022 7 3. Key Features

- Main IC : NXP / SR150

- Compliant with IEEE802.15.4z HRP PHY

- Supports SHF UWB bands, Ch5(6489.6MHz) and 9(7987.2MHz)

- Supports 62.4MHz,124.8MHz and 249.6MHz PRF mode

- Data rates of 6.81Mbps, 7.8Mbps, 27.24Mbps and 31.2Mbps Copyright Murata Manufacturing Co., Ltd. All rights reserved. 03 August 2022 8 4.Antenna Maker P/N Type Gain [dBi]

5ch 9ch Appearance Supported Antenna Murata MTD-ANT-027-1-A_UWB_ANT18mm Patch 0.9 2.7 Copyright Murata Manufacturing Co., Ltd. All rights reserved. 03 August 2022 9 4.Antenna 50-ohm line(microstrip line pattern) Certification tests are conducted in the following patterns. The 50ohm microstrip line needs to be copied when module is installed in the End product. Murata provides set makers with Gerber data or something similar Copyright Murata Manufacturing Co., Ltd. All rights reserved. 03 August 2022 10

LBUA0VG2BP Label Design and Location 6.6mm 0.7mm 0.7mm 0.6mm There is no space to describe the FCC ID Number. Therefore, it is described on the manual and package. m m 8 5

. m m 8 2

. 1.0mm Murata Logo mark 2BP Model Type name MS1119001Inspection Number Pin 1 Marking 2D Code Copyright Murata Manufacturing Co., Ltd. All rights reserved. 23 June 2022 1 LBUA0VG2BP Label Design and Location The character size is 4 points or more. FCC ID:VPYLB2BP IC: 772C-LB2BP HVIN:LBUA0VG2BP This device complies with part 15 of FCC Rules and Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 23 June 2022 2

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name Murata Manufacturing Co., Ltd. Address Grantee Code FCC ID 10-1, Higashikotari 1-chome Nagaokakyo-shi Kyoto 617-8555 Japan VPY VPYLB2BP Authorized Contact Name KENJI HAYASHIKOSHI Contact Email Contact Phone koshi@murata.com 81-75-955-6173 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

a) b) c) d) e) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature:

Date: 2022-06-02 Print Name:

Title:

KENJI HAYASHIKOSHI SENIOR MANAGER

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Applicant Declaration Rev:0.0

Murata Manufacturing Co., Ltd. TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding:

Confidentiality Request regarding application for FCC ID: VPYLB2BP LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 180 days from the grant date, whichever is less. If the device is marketed within aforementioned days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Print Name: KENJI HAYASHIKOSHI Title: SENIOR MANAGER Signature:

On behalf of Company: Murata Manufacturing Co., Ltd. Telephone: 81-75-955-6173 E-mail: koshi@murata.com

Murata Manufacturing Co., Ltd. Cover Letter-Modular Approval FCC ID:VPYLB2BP Date: 2022-6-2 Gentlemen:

Theres a Communication Module that would like to have your authorization as a modular approval. The specific product as below, Communication Module with its designed features and specified description, meets special requirements for Limit modular approval on FCC KDB996369 by cross-reference list below. Company Model Name Model Number FCC ID Murata Manufacturing Co., Ltd. Communication Module LBUA0VG2BP VPYLB2BP Requirement of FCC KDB996369 ComplyY/N 1. The modular transmitter must have its own RF Y shielding. The EUT provides the RF shielding. See EUT 2. The modular transmitter must have buffered photo. Y modulation/data inputs (if such inputs are provided) The EUT has its buffered modulation. Please see to ensure that the module will comply with Part 15 the Schematic Diagram. requirements under conditions of excessive data rates or over-modulation. 3. The modular transmitter must have its own N power supply regulation. The EUT has its own power supply regulation, but Power supply for PA is directly. please see the Schematic Diagram. 4. The modular transmitter must comply with the Y antenna and transmission system requirements of The EUT meets the FCC antenna requirements;

Sections 15.203, 15.204(b) and 15.204(c). The Instructions are described in Operational antenna must either be permanently attached or description employ a unique antenna coupler (at all connections between the module and the antenna, including the cable). The professional installation provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. 5. The modular transmitter must be tested in a stand Y alone configuration, i.e., the module must not be The EUT was tested with a test board, please see inside another device during testing. test report and setup photo 6. The modular transmitter must be labeled with its N own FCC ID number, and, if the FCC ID is not Due to the small size of this module, the FCC ID visible when the module is installed inside another cannot be printed on the module body. Post the device, then the outside of the device into which the FCC ID in the User manual. Murata Manufacturing Co., Ltd. module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following:

Contains Transmitter Module FCC ID:VPYLB2BP or Contains FCC ID:VPYLB2BP Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. 7. The modular transmitter must comply with any Y specific rule or operating requirements The EUT is compliant with all applicable FCC applicable to the transmitter and rules. Details instructions for maintaining the manufacturer must provide adequate compliance are give in the User Manual. instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. 8. The modular transmitter must comply with any Y applicable RF exposure The EUT complies with RF exposure requirement. requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In ad dition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Thank you. Sincerely, Print Name: KENJI HAYASHIKOSHI Title: SENIOR MANAGER Signature:

Murata Manufacturing Co., Ltd. On behalf of Company: Murata Manufacturing Co., Ltd. Telephone: 81-75-955-6173 E-mail: koshi@murata.com