FCC ID: VPYLBEE5HY1MW Communication Module

LBEE5HY1MW Installation Manual 1 / 9 FCC ID of this product is as follows. FCC ID: VPYLBEE5HY1MW IC No. of this product is as follows. IC: 772C-LBEE5HY1MW Contents 1. Land Pattern (Recommended) 2. PIN Layout 3. Antenna 4. Supply Voltage and Operating Temperature 5. Theory of Operation-Channel List 6. Theory of Output Power List 1. Land Pattern (Recommended) 2 / 9 Unit : mm 2. PIN Layout 3 / 9 3. Antenna 4 / 9 Please perform the antenna design that followed the specifications of the antenna. About the signal line between an antenna and a module It is a 50-ohm line design. Fine tuning of return loss etc. can be performed using a matching network. However, it is required to check "Class1 change" and "Class2 change" which the authorities define then. The concrete contents of a check are the following three points. 1) It is the same type as the antenna type of antenna specifications. 2) An antenna gain is lower than a gain given in antenna specifications. 3) The emission level is not getting worse. 50-ohm line(microstrip line length) Antenna Antenna type Loop antenna 50-ohm feed line length We test it at 0mm as a representative 5 / 9 Recommended antenna design This Antenna Specification is based on Keyence's requirement.. Model name LBEE5HY1MW Antenna Model Name

: ANT16244DT Antenna type

: Loop antenna Antenna manufacture

: TDK Corporation Antenna gain

: +2.1 dBi @2442MHz

+3.5 dBi @5150MHz Frequency

: 2400-2483.5MHz, 5150-5850MHz Recommended antenna characteristics 6 / 9 4. Supply Voltage 7 / 9 Parameter Min. Typ. Max. Unit Operating Temperature*1 Supply Voltage VBAT VIO*2 1.8V/3.3V

-30 3.2 1.62 25 3.3

+85 4.8 3.63 deg.C V V

*1: Surface temperature of the shield case Functionality is guaranteed but specifications require derating at extreme temperatures

*2: VIO dont influence the RF characteristic. Tolerance of 1.8V and 3.3V is 10%. 5. Theory of Operation-Channel List Theory of Operation-Software Security and Channel List Frequency of operation Scan Ad-hoc mode 2.4GHz 11b/g/n (HT20) 2412-2462MHz BT 2402-2480MHz 11a/n ((V)HT20) 5180-5240MHz Active N/A Active Yes N/A Yes 11a/n ((V)HT20) 5260-5320MHz Passive No W52 W53

* This specification is limited to use in the above frequency bands and modes. Notes: End users cannot modify the software because F/W & driver are installed in device. 6. Theory of Output Power List This specification is limited to use with the following output power settings. 8 / 9 Limited output power setting. [dBm]

2.4GHz WLAN Mode Rate IEEE 802.11b IEEE 802.11g IEEE 802.11n 1M 2M 5.5M 11M 6M 9M 12M 18M 24M 36M 48M 54M MCS0 MCS1 MCS2 MCS3 MCS4 MCS5 MCS6 MCS7 5GHz WLAN 1ch 14.0 14.0 14.0 14.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 2ch 14.0 14.0 14.0 14.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 3ch 14.0 14.0 14.0 14.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.0 12.0 12.0 4ch 14.0 14.0 14.0 14.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.0 12.0 12.0 5ch 14.0 14.0 14.0 14.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.0 12.0 12.0 6ch 14.0 14.0 14.0 14.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.0 12.0 12.0 7ch 14.0 14.0 14.0 14.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.0 12.0 12.0 8ch 14.0 14.0 14.0 14.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.0 12.0 12.0 9ch 14.0 14.0 14.0 14.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 12.0 12.0 12.0 10ch 11ch 14.0 14.0 14.0 14.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 14.0 14.0 14.0 14.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 Mode Rate 36ch 40ch 44ch 48ch 52ch 56ch 60ch 64ch IEEE 802.11a IEEE 802.11n

(HT20) 6M 9M 12M 18M 24M 36M 48M 54M MCS0 MCS1 MCS2 MCS3 MCS4 MCS5 MCS6 MCS7 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 LBEE5HY1MW User Manual for FCC Regarding FCC modular approval of LBEE5HY1MW Model Name: LBEE5HY1MW FCC ID: VPYLBEE5HY1MW 9 / 9 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Since this module is not sold to general end users directly, there is no user manual of module. For the details about this module, please refer to the specification sheet of module. This module should be installed in the host device according to the interface specification (installation procedure). The following information must be indicated on the host device of this module. Contains Transmitter Module FCC ID: VPYLBEE5HY1MW or Contains FCC ID: VPYLBEE5HY1MW This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

*If it cannot be described on the host product, it must be listed on both the host product manual and on the host product package or removable label. The following statements must be described on the user manual of the host device of this module;

10 / 9 FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Compliance with FCC requirement 15.407(c) Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure. Frequency Tolerance: 20 ppm This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. When installing it in a mobile equipment. Please describe the following warning to the manual. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body. When installing it in a portable equipment. Please describe the following warning to the manual. The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure of low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. LBEE5HY1MW has been tested and found to comply with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. It is necessary to take a SAR test with your set mounting this module (except to use only Bluetooth V5.0(BDR/EDR/LE)). Class II permissive change application is necessary using the SAR report. Please contact Murata. Note) Portable equipment: Equipment for which the spaces between human body and antenna are used within 20cm. Mobile equipment: Equipment used at position in which the spaces between human body and antenna exceeded 20cm. 11 / 9 LBEE5HY1MW User Manual for ISED 12 / 9 PMN: LBEE5HY1MW HVIN: LBEE5HY1MW IC Number: 772C-LBEE5HY1MW Since this module is not sold to general end users directly, there is no user manual of module. For the details about this module, please refer to the specification sheet of module. This module should be installed in the host device according to the interface specification (installation procedure). The following information must be indicated on the host device of this module. Contains IC: 772C-LBEE5HY1MW The following statements must be described on the user manual of the host device of this module;

This device complies with Industry Canadas applicable licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

1) lappareil ne doit pas produire de brouillage;

2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement.

*If it is difficult to describe this statement on the host product due to the size, please describe in the User's manual. In case of the final product which can be carried around to outdoor. The following indication is necessary to the final product. When the AP function is used in W52;

At the time of a channel setting of W52, please indicate for indoor use only. During connecting, please show the channel number which connects. And please indicate that the end user may find out "for indoor use only channel". When the STA function is used in channel 52, 54, 58, at the time of the channel 52 or 54 or 58 setting, 13 / 9 please indicate for indoor use only channel. During connecting, please show the channel number which connects. And please indicate that the end user may find out "for indoor use only channel". If the antenna of the end product is removed, please describe the follow warning on the manual of the end product which contains this module. This radio transmitter (IC Number: 772C-LBEE5HY1MW) identify the device by certification number or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

: 2.4GHz Loop Gain: +2.1 dBi

: 5GHz Loop Gain: +3.5 dBi Le prsent metteur radio (IC Number: 772C-LBEE5HY1MW) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Type dantenne

: 2.4GHz Loop Gain: +2.1 dBi

: 5GHz Loop Gain: +3.5 dBi If the final product use the following frequency, please note that there is a limit. For indoor use only (5150-5250MHz band and channel 52, 54, 58) Pour usage intrieur seulement (5150-5250MHz band and channel 52, 54, 58) The following statements must be described on the user manual of the host device of this module;

14 / 9 Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure. La transmission des donnes est toujours initie par le logiciel, puis les donnes sont transmises par l'intermdiaire du MAC, par la bande de base numrique et analogique et, enfin, la puce RF. Plusieurs paquets spciaux sont initis par le MAC. Ce sont les seuls moyens pour qu'une partie de la bande de base numrique active l'metteur RF, puis dsactive celui-ci la fin du paquet. En consquence, l'metteur reste uniquement activ lors de la transmission d'un des paquets susmentionns. En d'autres termes, ce dispositif interrompt automatiquement toute transmission en cas d'absence d'information transmettre ou de dfaillance.

*If it is difficult to describe this statement on the host product due to the size, please describe in the User's manual. When installing it in a mobile equipment. Please describe the following warning to the manual. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body. Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement doit tre install et utilis en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain.

LBEE5HY1MW Installation Manual FCC ID of this product is as follows. FCC ID: VPYLBEE5HY1MW IC No. of this product is as follows. IC : 772C-LBEE5HY1MW Contents 1.Land Pattern (Recommended) 2.PIN Layout 3.Supply Voltage 4.Theory of Operation-Channel List 5. Antenna CONFIDENTIAL Copyright Murata Manufacturing Co., Ltd. All rights reserved. 30 January 2018 1 1. Land Pattern TOP View CONFIDENTIAL Copyright Murata Manufacturing Co., Ltd. All rights reserved. 30 January 2018 2 Unit : mm 2. PIN Layout CONFIDENTIAL Copyright Murata Manufacturing Co., Ltd. All rights reserved. 30 January 2018 3 3. Supply Voltage Parameter Min. Typ. Max. Unit Operating Temperature*1 Supply Voltage VBAT

-30 3.2 VIO*2 1.8V/3.3V 1.62 25 3.3

-

+85 4.8 3.63 deg.C V V

*1: Surface temperature of the shield case Functionality is guaranteed but specifications require derating at extreme temperatures

*2: VIO dont influence the RF characteristic. Tolerance of 1.8V and 3.3V is 10%. CONFIDENTIAL Copyright Murata Manufacturing Co., Ltd. All rights reserved. 30 January 2018 4 4. Theory of Operation-Channel List Theory of Operation-Software Security and Channel List Frequency of operation 2.4GHz 11b/g/n (HT20) 2412-2462MHz BT BLE 2402-2480MHz 2402-2480MHz W52 11a/n/ac ((V)HT20) 5180-5240MHz 11n/ac ((V)HT40) 5190-5230MHz 11ac (VHT80) 5210MHz W53 11a/n/ac ((V)HT20) 5260-5320MHz 11n/ac ((V)HT40) 5270-5310MHz 11ac (VHT80) 5290MHz W56 11a/n/ac ((V)HT20) 5500-5720MHz *

11n/ac ((V)HT40) 5510-5710MHz *

11ac (VHT80) 5530-5690MHz *

W58 11a/n/ac ((V)HT20) 5745-5825MHz 11n/ac ((V)HT40) 5755-5795MHz 11ac (VHT80) 5775MHz Scan Active N/A N/A Active Active Active Passive Passive Passive Passive Passive Passive Active Active Active Ad-hoc mode Yes N/A N/A Yes Yes Yes No No No No No No Yes Yes Yes

* The frequency band 5600MHz-5640MHz (11a/n/ac 20M band), 5590MHz-5630MHz (11n/ac 40M band) and CONFIDENTIAL 5610MHz (11ac 80M band) is restricted in ISED. Notes: End users can not modify the software because F/W & driver are installed in device. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 30 January 2018 5 5. Antenna Please perform the antenna design that followed the specifications of the antenna. About the signal line between an antenna and a module It is a 50-ohm line design. Fine tuning of return loss etc. can be performed using a matching network. However, it is required to check "Class1 change" and "Class2 change"

which the authorities define then. The concrete contents of a check are the following three points. It is the same type as the antenna type of antenna specifications. An antenna gain is lower than a gain given in antenna specifications. The emission level is not getting worse. 50-ohm line(microstrip line length) Antenna Antenna type Monopole pattern antenna 50-ohm feed line length We test it at 0mm as a representative CONFIDENTIAL Copyright Murata Manufacturing Co., Ltd. All rights reserved. 30 January 2018 6

User Manual Murata Manufacturing Co.,Ltd. 1 murata.com Copyright Murata Manufacturing Co., Ltd. All rights reserved. 1 Copyright Murata Manufacturing Co., Ltd. All rights reserved. 19 April 2018 19 April 2018 LBEE5HY1MW User Manual for FCC Regarding FCC modular approval of LBEE5HY1MW Model Name: LBEE5HY1MW FCC ID:VPYLBEE5HY1MW This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 19 April 2018 2 LBEE5HY1MW User Manual for FCC Since this module is not sold to general end users directly, there is no user manual of module. For the details about this module, please refer to the specification sheet of module. This module should be installed in the host device according to the interface specification

(installation procedure). The following information must be indicated on the host device of this module. Contains Transmitter Module FCC ID:VPYLBEE5HY1MW or Contains FCC ID: VPYLBEE5HY1MW This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

*If it can not be described on the host product, it must be listed on both the host product manual and on the host product package or removable label. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 19 April 2018 3 LBEE5HY1MW User Manual for FCC The following statements must be described on the user manual of the host device of this module;

FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Compliance with FCC requirement 15.407(c) Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure. Frequency Tolerance: 20 ppm This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 19 April 2018 4 LBEE5HY1MW User Manual for FCC When installing it in a mobile equipment. Please describe the following warning to the manual. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body. When installing it in a portable equipment. Please describe the following warning to the manual. The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure of low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. LBEE5HY1MW has been tested and found to comply with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. It is necessary to take a SAR test with your set mounting this module (except to use only Bluetooth V4.2(BDR/EDR/LE)). Class II permissive change application is necessary using the SAR report. Please contact Murata. Note) Portable equipment : Equipment for which the spaces between human body and antenna are used within 20cm. Mobile equipment : Equipment used at position in which the spaces between human body and antenna exceeded 20cm. Antenna Please refer to the Antenna Specification document supplied by Murata or please contact Murata for the detail designation of how to design the Antenna trace. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 19 April 2018 5

Authority to Act as Agent Date: Sep.06.2022 _ TUV Rheinland of North America, Inc. 1279 Quarry Lane., Suite. A Pleasanton, CA 94566 To Whom It May Concern:

I appoint _Mr. Weidong Wang of TV Rheinland Shanghai Co., Ltd. to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the FCC or Industry Canadas regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by TUV Rheinland Group, still resides with Murata Manufacturing Co., Ltd. / 10-1, Higashikotari 1-chome, Nagaokakyo-shi, Kyoto, 617-8555 Japan. For TCB applications, We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Date:

_ Sep.16.2022_ Agreement is valid for 12 months from the above date. By:

_Kenji Hayashikoshi_________

(Signature) _

(Print name) ___ _Senior Manager____________

(Title) _+81-75-955-6173_________

(Telephone) On behalf of:

Murata Manufacturing Co., Ltd.

(Company Name) Page 1 of 1

Summary Module: LBEE5HY1MW Antenna model number

: ANT162442DT Antenna type

: Monopole antenna (Chip + pattern) Max antenna gain

: +2.1 dBi @2442MHz Frequency range

: 2400-2483.5MHz, 5150-5850MHz

+3.5 dBi @5150MHz Copyright Murata Manufacturing Co., Ltd. All rights reserved. 11 October 2022 1 Appearance Copyright Murata Manufacturing Co., Ltd. All rights reserved. 11 October 2022 2 Measurement condition Copyright Murata Manufacturing Co., Ltd. All rights reserved. 11 October 2022 3 Antenna characteristics Copyright Murata Manufacturing Co., Ltd. All rights reserved. 11 October 2022 4 Antenna characteristics

* Typical (2442MHz) waveform data Copyright Murata Manufacturing Co., Ltd. All rights reserved. 11 October 2022 5

Data: Sep.16.2022 To:

Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Roads, Columbia, MD 21046 Dear Examiner, This is to request a Class II permissive change for FCC ID: VPYLBEE5HY1MW (original grant date: 2018/05/24). Applicant: Murata Manufacturing Co., Ltd. The reasons for there change are as below:

1. Add an antenna. Peak gain: 2.1dBi in 2.4GHz band, 3.5dBi in 5GHz band. 2. The following Specification will be disabled Bluetooth LE 5GHz Wi-Fi to be disabled Frequency range 5470-5725MHz to be disabled Frequency range 5725-5850MHz to be disabled 802.11n-HT40: to be disabled 802.11ac-VHT20: to be disabled 802.11ac-VHT40: to be disabled 802.11ac-VHT80: to be disabled 3. The following Specification conducted power will be reduced 2.4GHz Wi-Fi 5GHz Wi-Fi 802.11b: to be reduced 802.11g: to be reduced 802.11n-HT20: to be reduced 802.11a: to be reduced 802.11n-HT20: to be reduced 4. 2.4G WiFi: 802.11 b/g/n-HT20 support AP and STA mode, 5G WIFI: AP mode support U-NII-1, STA mode support U-NII-1 and U-NII-2A. Above 2,3,4 changes are performed by software and do not require any hardware changes. Software changes are changed by the grantee, and cannot be changed by third parties. Sincerely, By:

Kenji Hayashikoshi / Senior Manager

(Signature/Title)

(Print name)

Applicant/Grantee Murata Manufacturing Co., Ltd. FCC ID:

Request for Modular Approval IC:

VPYLBEE5HY1MW Section 15.212 Modular Transmitters / Section 3.2 of RSS-Gen Request for Limited Modular Approval 772C-LBEE5HY1MW Requirements Device Conditions Comply (Y/N) Single Modular Approval Requirements The radio elements must have the radio frequency circuitry must be shielded. Physical/discrete and tuning capacitors may be located external to the shield, but must be on the module assembly. The module shall have buffered modulation/data input(s) (if such inputs are provided) to ensure that the module will comply with the requirements set out in the applicable RSS standard under conditions of excessive data rates or over-modulation. The module shall have its own power supply regulation on the module. This is to ensure that the module will comply with the requirements set out in the applicable standard regardless of the design of the power supplying circuitry in the host device which houses the module. Requirements set out in the applicable standard regardless of the design of the power supplying circuitry in the host device which houses the module. The module shall comply with the provisions for external power amplifiers and antennas detailed in this standard. The Equipment certification submission shall contain a detailed description of the configuration of all antennas that will be used with the module. The module shall be tested for compliance with the applicable standard in a stand-

alone configuration, i.e. the module must not be inside another device during testing. 1 2 3 4 5 The module has its own RF shielding. Shield Can is employed on the board structure, please see exhibition External Photo, the emission measurement was conducted without further shielding added. All modulation and data input(s) are buffered. The EUT has buffered data inputs, it is integrated on IC chip. Have its own power supply regulation. Instructions in Installation Manual. The EUT meets the FCC antenna Requirements. Option1 Monopole antenna,

+0.1 dBi@2442MHz

-0.4 dBi@5150MHz Option2 : Monopole antenna,

+2.1 dBi @2442MHz

+3.5 dBi @5150MHz The modular transmitter has been performed the testing in a state of being installed on a test jig board simulating the board of the installed end product, therefore has not been performed the testing as a stand-alone and then confirmed the compliance. The module and antenna will be mounted on a board similar to the one shown in the test set photo, and the board will be installed in the end product. Y Y Y Y Y The module shall comply with the Category I equipment labelling requirements. 6 In the exhibition OEM manual, there are Instructions given to the OEM on how to label the end product. The modular transmitter complies with all specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer will provide adequate instructions along with the module to explain any such requirements. A copy of these instructions is included in this application for equipment authorization:

Address compliance with the Commission's RF exposure limits in Sections 1.1310 and 2.1093. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF exposure compliance in accordance with Section 15.247(b)(4). 7 8a Instructions in User Manual Please refer the Maximum Permissible Exposure Information. The module shall comply with applicable RSS-102 exposure requirements, which are based on the intended use/configurations. 8b Please refer the Maximum Permissible Exposure Information. 9 Is the modular device for an Industry Canada licensed exempt service?

Y Y Y Y Y A limited modular approval may be granted for single or split modular transmitters that do not comply with all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation, if the manufacturer can demonstrate by alternative means in the application for equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the operating conditions in which the transmitter will be used. Limited modular approval also may be granted in those instances where compliance with RF exposure rules is demonstrated only for particular product configurations. The applicant for certification must state how control of the end product into which the module will be installed will be maintained such that full compliance of the end product is always ensured. Signature Name/Title: Kenji Hayashikoshi Company Name: Murata manufacturing Co., Ltd. Date: Sep.16,2022

INNOVATOR IN ELECTRONICS To whom it may concern:

Special Power of Attorney I, MOTOO HAYASHI of Murata Manufacturing Co., Ltd. hereby appoint Kenji Hayashikoshi of Murata Manufacturing Co., Ltd. to represent me to act on my behalf to do any and all of the following:

Sign the following documents on my behalf and apply to FCC for the products

- Letter of agency and anti-drug

- Confidentiality cover letters

- Any other application document that requires a signature by grantee. The rights, powers and authority in fact to exercise any and all of the rights and powers herein granted shall commence and be in full force and effective for one year from May 11, 2022 unless specifically extended or terminated by either party. Date: May 11, 2022 Place: Japan MOTOO HAYAS Murata Manufacturing/Co., Ltd. Cateecfeg act!