FCC ID: VPYLBEE5ZZ1XL Communication Module

LBEE5ZZ1XL User Manual for FCC Model Name: LBEE5ZZ1XL FCC ID: VPYLBEE5ZZ1XL Since this module is not sold to general end users directly, there is no user manual of module. For the details about this module, please refer to the specification sheet of module. This module should be installed in the host device according to the interface specification (installation procedure) The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the end users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as shown in User manual. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This device complies with below part 15 of the FCC Rules. Part 15 Subpart C Part 15 Subpart E Copyright Murata Manufacturing Co., Ltd. All rights reserved. 17 May 2023 1 LBEE5ZZ1XL User Manual for FCC The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. This module designed for mounting inside of the end product by us professionally. Therefore, it complies with the antenna and transmission system requirements of 15.203. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 17 May 2023 2 LBEE5ZZ1XL User Manual for FCC This manual is based on KDB 996369, which is designed to ensure that module manufacturer correctly communication the necessary information to host manufacturers that incorporate their modules. INTEGRATION INSTRUCTIONS 1. General: Applicable Sections 2 through 10 describe the items that must be provided in the integration instructions for host product manufacturers (e.g., OEM instruction manual) to use when integrating a module in a host product. This Modular transmitter applicant(muRata) should include information in their instructions for all these items indicating clearly when they are not applicable. 2. List of applicable FCC rules: Applicable This device complies with below part 15 of FCC Rules. Part 15.247 Part 15.407 Copyright Murata Manufacturing Co., Ltd. All rights reserved. 17 May 2023 3 LBEE5ZZ1XL User Manual for FCC 3. Summarize the specific operational use conditions : Applicable This module designed for mounting inside of the end product by us professionally. Therefore, it complies with the antenna and transmission system requirements of 15.203. 4. Limited module procedures : Applicable This module does not supply a regulated voltage, it can only be used in a host that supplies regulated voltage. See page 12 About Power Supply(limited condition). Copyright Murata Manufacturing Co., Ltd. All rights reserved. 17 May 2023 4 LBEE5ZZ1XL User Manual for FCC 6. RF exposure considerations : Applicable This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body. It is necessary to take a SAR test with your set mounting this module (except to use only Bluetooth). Class II permissive change application is necessary using the SAR report. Please contact Murata. And an application for a Class II permissive change from a Mobile equipment to a Portable equipment is also required. Note) Portable equipment : Equipment for which the spaces between human body and antenna are used within 20cm. Mobile equipment : Equipment used at position in which the spaces between human body and antenna exceeded 20cm. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 17 May 2023 5 LBEE5ZZ1XL User Manual for FCC 7. Antennas : Applicable Part number Vendor Peak Gain(dBi) 2.4GHz 5GHz Type Connector 146153 Molex 3.2 4.25 Dipole U.FL Copyright Murata Manufacturing Co., Ltd. All rights reserved. 17 May 2023 6 LBEE5ZZ1XL User Manual for FCC 8. Label and compliance information : Applicable The following statements must be described on the user manual of the host device of this module;

Contains Transmitter Module FCC ID: VPYLBEE5ZZ1XL or Contains FCC ID: VPYLBEE5ZZ1XL This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

*If it is difficult to describe this statement on the host device due to the size, please describe in the user's manual and also either describe on the device packaging or on a removable label attached to the device. FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Compliance with FCC requirement 15.407(c) Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure. Frequency Tolerance: 20 ppm This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 17 May 2023 7 LBEE5ZZ1XL User Manual for FCC When installing it in a mobile equipment. Please describe the following warning to the manual. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body. This module is only approval as a mobile equipment. Therefore, do not install it on portable equipment. If you wish to use it as a portable equipment, please contact Murata in advance as Class application accompanied by SAR testing using the final product are required. Note) Portable equipment : Equipment for which the spaces between human body and antenna are used within 20cm. Mobile equipment : Equipment used at position in which the spaces between human body and antenna exceeded 20cm. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 17 May 2023 8 LBEE5ZZ1XL User Manual for FCC 9. Information on test modes and additional testing requirements: Applicable Please check the installation manual first. Please contact Murata if you have any questions when conducting the RF certification test on the host. We (Murata) are ready to present the control manual and others for the RF certification test. 10. Additional testing, Part 15 Subpart B disclaimer : Applicable The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 17 May 2023 9 LBEE5ZZ1XL User Manual for FCC If the final product with this module is FCC Class A digital device, include the following in the manual of the final product:

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. If the final product with this module is FCC Class B digital device, include the following in the manual of the final product:

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 17 May 2023 10 LBEE5ZZ1XL User Manual for FCC 11. Note EMI Considerations : Applicable Note that a host manufacture is recommended to use KDB 996369 D04 Module Integration Guide recommending as

"best practice" RF design engineering testing and evaluation in case non-linear interactions generate additional non-compliant limits due to module placement to host components or properties. For standalone mode, reference the guidance in D04 Module Integration Guide and for simultaneous mode7; see D02 Module Q&A Question 12, which permits the host manufacturer to confirm compliance. 12. How to make changes: Applicable When changing from the conditions of approval, please present technical documentation that it is equivalent to a Class change. For example, when adding or changing an antenna, the following technical documents are required. 1)The document indicating the same type as the original antenna 2)Technical document showing that the gain is the same or lower than the gain at the time of the original approval 3)Technical document showing that the spurious is no more than 3 dB worse than when it was originally certified Copyright Murata Manufacturing Co., Ltd. All rights reserved. 17 May 2023 11 LBEE5ZZ1XL User Manual for FCC About Power supply(Limited condition) This Module(LBEE5ZZ1XL and LBEE5ZZ2XS) have been approved as Limited Modular Approval. These modules do not have a voltage stabilizing circuit in the power path to the internal RF circuitry. Therefore, the Limited Condition must provide a stable power supply for the supply voltage to the module. Please supply a stable power supply so that the voltage shown in the table below is applied. Parameter Supply Voltage VDD33 VDD18 VIO VIO_SD Min. 3.14 1.71 1.71 3.14 1.71 3.14 Typ. 3.3 1.8 1.8 3.3 1.8 3.3 Max. 3.46 1.89 1.89 3.46 1.89 3.46 unit V V V V Copyright Murata Manufacturing Co., Ltd. All rights reserved. 17 May 2023 12 LBEE5ZZ1XL User Manual for FCC Microstrip trace line on the host PCB to the antenna connectors About the signal line between an antenna and a module It is a 50-ohm line design. Fine tuning of return loss etc. can be performed using a matching network. However, it is required to check "Class1 change" and "Class2 change"

which the authorities define then. The concrete contents of a check as follows. 1Different length and shapes affect radiated emissions, must confirm the same specification is used as the following page 14 and 15. 2The emission level is not getting worse. The following is the design of the EVB used for the test. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 17 May 2023 13 LBEE5ZZ1XL User Manual for FCC Certification tests are conducted in the following patterns. The 50ohm microstrip line needs to be copied when module is installed in the End product. Murata provides set makers with Gerber data or something similar. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 17 May 2023 14 LBEE5ZZ1XL User Manual for FCC About the Trace antenna and feed line of the jig where the certification test was conducted Substrate type name of certification test jig: P2ML9917 feed line width : 0.4mm Substrate thin : 0.8 0.1 mm Substrate material: FR -4 Substrate thickness between GND layer and surface layer: 0.408mm 1.0mm 1.0mm 1.0mm 2.5mm 1.7mm 1.8mm 1.2mm Copyright Murata Manufacturing Co., Ltd. All rights reserved. 17 May 2023 15

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: March 9, 2023 Ref: Attestation Statements Part 2.911(d)(5)(i)&(ii) Filing FCC ID: VPYLBEE5ZZ1XL Statement for 47 CFR section 2.911(d)(5)(i) Murata Manufacturing Co., Ltd. (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Statement for 47 CFR section 2.911(d)(5)(ii) Murata Manufacturing Co., Ltd. (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Sincerely, Signature: ____________________ KENJI HAYASHIKOSHI /Senior Manager Murata Manufacturing Co., Ltd.

Date: March 30, 2023 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Requesting Class II permissive change To Whom It May Concern:

The purpose of this letter is to request a Class II Permissive change for FCC ID: VPYLBEE5ZZ1XL, Original grant date: July 4, 2022 The major change filed under this application is 1. To reduce the output power for WiFi 2.4GHz and 5GHz via software, the BT and BLE is remained unchanged, please refer to the test reports for the details. 2. Evaluation has been done to ensure compliance of EMC and RF exposure. 3. The hardware design of this transmitter that may affect compliance is remained unchanged in this permissive change application. 4. The security mechanism according to section II of KDB 594280 D02 is remained unchanged as it reported to the FCC at the initial certification. 5. EMC test reports are provided for demonstrating compliance of this modification, test results that does not affected compliance are also leveraged from the original authorization. Sincerely,

(Signature) Name: KENJI HAYASHIKOSHI Title: Senior Manager On behalf of: Murata Manufacturing Co., Ltd.

FCC, Request for non-disclosure RF_501, Issue 6 Date: 16-Jul-10 Page 1 of 1 Company Name: Murata Manufacturing Co., Ltd. Address:

City:

Country:

10-1, Higashikotari 1-chome Nagaokakyo-shi, Kyoto 617-8555, Japan To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: VPYLBEE5ZZ1XL Reference number: ######

Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application:

Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (note 1):

Internal Photos Users Manual Test Set-up Photos External Photos Justification: Ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. Planned Release Date STC: 180 days (notes 2, 3, 4, 5) Date: 12 May 2023 Name and signature of applicant: KENJI HAYASHIKOSHI Notes:

1) A document or type of document can only have ONE type of confidentiality!

2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)!

3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this!

5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

RF_160, Issue 04 Declaration of Authorization Murata Manufacturing Co., Ltd. 10-1, Higashikotari 1-chome Nagaokakyo-shi, Kyoto 617-8555 Japan We Name:

Address:

City:

Country:

Declare that:

Name Representative of agent: Jim Chang Agent Company name:

SGS Taiwan Ltd. Address:

City:

Country:

134, Wu Kung Road, Wu ku Industrial Zone TW- New Taipei City 24803 New Taipei City Taiwan is authorized to apply for Certification of the following product(s):

Product description: Communication Module Type designation:

LBEE5ZZ1XL, LBEE5ZZ2XS Trademark:

muRata on our behalf, Date: February 10, 2023 City: Kyoto Name: KENJI HAYASHIKOSHI Function: Senior Manager Signature:

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: March 3, 2023 Ref: Attestation Statements Part 2.911(d)(7) Filing

[Murata Manufacturing Co., Ltd.] (the applicant) certifies that, as of the date of the filing of the application, [Murata Electronics North America, Inc.] is our designated U.S. agent for service of process.[Murata Manufacturing Co., Ltd.] accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment.

[Murata Electronics North America, Inc.] accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process. Sincerely, Designated U.S. Agent Information:

Name: Murata Electronics North America, Inc. FRN: 0024753089 Contact Person: Mark E Tucker Address: 2200 Lake Park Drive Smyma, GA 30080-7604 United States Tel.: (678)684-2009 Email: mtucker@murata.com Mark E. Tucker 3/3/2023 U.S. Agent Signature:

Applicant:

Company Name: Murata Manufacturing Co., Ltd. Contact Person: Kenji Hayashikoshi Address: 1-10-1, Higashikotari, Nagaokakyo-shi, Kyoto 617-8555 Japan Tel.: +81-75-955-6736 Email: mhayashi@murata.com Applicant Signature:

To whom it may concern, we declare below featured for equipment authorization regarding DTS-UNII Device Declaration Letter Date June 13, 2022:

FCC ID: VPYLBEE5ZZ1XL

(1) DFS Device --

Master, Client with Radar detection capability, Client without radar detection capability, N/A

(2) Active / Passive Scanning Frequency Band(MHz) 5150 - 5250 5250 - 5350 5470 - 5725 5725 - 5850 Active Scanning

(able to select a channel and initiate a network by sending enabling signals to other devices) Passive scanning

(not able to initiate a network) Non Applicable Yes , No Yes , No Yes , No Yes , No Yes , No Yes , No Yes , No Yes , No Country code selection ability - Yes , No

(3) If yes, pls explain how it was implemented : Country code is factory set and cannot be changed by end users. Title / Name (Printed): Senior Manager, Kenji Hayashikoshi Signature:

WIFI Channel 12 & 13 Declaration Letter Date: 2022/6/13 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding FCC ID: VPYLBEE5ZZ1XL To who it may concern, we have declared below featured for FCC equipment authorization in regard to 802.11b/g/n channel 12 & 13 operating capability. Please check Product hardware does not have the capability to operate on channel 12 &

13. Product hardware has the capability to operate on channel 12 & 13. However , these 2 channels will be disabled via software and user will not able to enable these 2 channels Product hardware has the capability to operate on channel 12 & 13. And meeting KDB 594280 D01 requirement. Compliance is demonstrated in test report as the maximum transmit power is properly adjusted to comply with the out-of-band emission requirements in Part 15.247. The device is a WiFi client device that is not able to operate at different power levels as the default setting, which is not accessible to third-party. Others Pls explain detail here. Signature:

Name (Printed): Kenji Hayashikoshi Title: Senior Manager On behalf of Company: Murata Manufacturing Co., Ltd. Telephone: +81-75-955-6736 Address: 10-1, Higashikotari 1-chome Nagaokakyo-shi, Kyoto 617-8555, Japan