FCC ID: VPYLBES5PL2EL Communication Module

LBES5PL2EL User Manual for FCC Model Name: LBES5PL2EL FCC ID: VPYLBES5PL2EL Since this module is not sold to general end users directly, there is no user manual of module. For the details about this module, please refer to the specification sheet of module. This module should be installed in the host device according to the interface specification (installation procedure) The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the end users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as shown in User manual. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This device complies with below part 15 of the FCC Rules. Part 15 Subpart C Part 15 Subpart E Since there is no space which indicates FCC ID on this module, FCC ID is indicated in a manual. If the FCC ID is not visible when the module is installed inside another device, then the module is installed must also display a label referring to the enclosed module. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 04 April 2023 1 LBES5PL2EL User Manual for FCC The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. This module designed for mounting inside of the end product by us professionally. Therefore, it complies with the antenna and transmission system requirements of 15.203. Since there is no space which indicates FCC ID on this module, FCC ID is indicated in a manual. If the FCC ID is not visible when the module is installed inside another device, then the module is installed must also display a label referring to the enclosed module. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 04 April 2023 2 LBES5PL2EL User Manual for FCC This manual is based on KDB 996369, which is designed to ensure that module manufacturer correctly communication the necessary information to host manufacturers that incorporate their modules. INTEGRATION INSTRUCTIONS 1. General: Applicable Sections 2 through 10 describe the items that must be provided in the integration instructions for host product manufacturers (e.g., OEM instruction manual) to use when integrating a module in a host product. This Modular transmitter applicant(muRata) should include information in their instructions for all these items indicating clearly when they are not applicable. 2. List of applicable FCC rules: Applicable This device complies with below part 15 of FCC Rules. Part 15 Subpart C Part 15 Subpart E Copyright Murata Manufacturing Co., Ltd. All rights reserved. 04 April 2023 3 LBES5PL2EL User Manual for FCC 3. Summarize the specific operational use conditions : Applicable This module designed for mounting inside of the end product by us professionally. Therefore, it complies with the antenna and transmission system requirements of 15.203. 4. Limited module procedures : Applicable This module needs to supply a regulated voltage from host device. Since there is no space which indicates FCC ID on this module, FCC ID is indicated in a manual. If the FCC ID is not visible when the module is installed inside another device, then the module is installed must also display a label referring to the enclosed module. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 04 April 2023 4 LBES5PL2EL User Manual for FCC 5. Trace antenna designs : Applicable Please perform the Trace antenna design that followed the specifications of the antenna. The concrete contents of a check are the following three points. It is the same type as the antenna type of antenna specifications. Confirm the same size as the Gerber file. An antenna gain is lower than a gain given in antenna specifications. Measure the gain, and confirm the peak gain is less than the application value. The emission level is not getting worse. Measure the spurious, and confirm degradation of less than 3dB than spurious value of worst of report used for the application. However it is spurious defined below. Please send those reports to Murata. And please refer Antenna in Section 6 of the installation manual. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 04 April 2023 5 LBES5PL2EL User Manual for FCC 6. RF exposure considerations : Applicable This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body. It is necessary to take a SAR test with your set mounting this module (except to use only Bluetooth). Class II permissive change application is necessary using the SAR report. Please contact Murata. And an application for a Class II permissive change from a Mobile equipment to a Portable equipment is also required. Note) Portable equipment : Equipment for which the spaces between human body and antenna are used within 20cm. Mobile equipment : Equipment used at position in which the spaces between human body and antenna exceeded 20cm. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 04 April 2023 6 LBES5PL2EL User Manual for FCC 7. Antennas : Applicable Part number Vendor Peak Gain(dBi) 2.4GHz 5GHz Type Connector 146153 219611 Molex 3.2 Molex 2.67 WT32D1-KX Unictron W24P-U Invertek Type2EL_Antenna Murata 3.0 3.2 3.6 4.25 3.67 4.0 N/A 4.6 Dipole Dipole Dipole Dipole u.FL u.FL u.FL u.FL Monopole Trace No.4 W24P-U can only be used at 2.4GHz No.5 Type2EL_Antenna can only be used for ANT0(Antenna Port0) Copyright Murata Manufacturing Co., Ltd. All rights reserved. 04 April 2023 7 LBES5PL2EL User Manual for FCC 8. Label and compliance information : Applicable The following statements must be described on the user manual of the host device of this module;

Contains Transmitter Module FCC ID: VPYLBES5PL2EL or Contains FCC ID: VPYLBES5PL2EL This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

*If it is difficult to describe this statement on the host product due to the size, please describe in the User's manual. FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Compliance with FCC requirement 15.407(c) Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure. Frequency Tolerance: 20 ppm This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 04 April 2023 8 LBES5PL2EL User Manual for FCC When installing it in a mobile equipment. Please describe the following warning to the manual. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body. This module is only approval as a mobile equipment. Therefore, do not install it on portable equipment. If you wish to use it as a portable equipment, please contact Murata in advance as Class application accompanied by SAR testing using the final product are required. Note) Portable equipment : Equipment for which the spaces between human body and antenna are used within 20cm. Mobile equipment : Equipment used at position in which the spaces between human body and antenna exceeded 20cm. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 04 April 2023 9 LBES5PL2EL User Manual for FCC 9. Information on test modes and additional testing requirements: Applicable Please check the installation manual first. Please contact Murata if you have any questions when conducting the RF certification test on the host. We (Murata) are ready to present the control manual and others for the RF certification test. 10. Additional testing, Part 15 Subpart B disclaimer : Applicable The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 04 April 2023 10 LBES5PL2EL User Manual for FCC If the final product with this module is FCC Class A digital device, include the following in the manual of the final product:

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. If the final product with this module is FCC Class B digital device, include the following in the manual of the final product:

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 04 April 2023 11 LBES5PL2EL User Manual for FCC 11. Note EMI Considerations : Applicable Note that a host manufacture is recommended to use KDB 996369 D04 Module Integration Guide recommending as

"best practice" RF design engineering testing and evaluation in case non-linear interactions generate additional non-compliant limits due to module placement to host components or properties. For standalone mode, reference the guidance in D04 Module Integration Guide and for simultaneous mode7; see D02 Module Q&A Question 12, which permits the host manufacturer to confirm compliance. 12. How to make changes: Applicable When changing from the conditions of approval, please present technical documentation that it is equivalent to a Class change. For example, when adding or changing an antenna, the following technical documents are required. 1)The document indicating the same type as the original antenna 2)Technical document showing that the gain is the same or lower than the gain at the time of the original approval 3)Technical document showing that the spurious is no more than 3 dB worse than when it was originally certified Copyright Murata Manufacturing Co., Ltd. All rights reserved. 04 April 2023 12 LBES5PL2EL User Manual for FCC About Power supply(Limited condition) This Module(LBES5PL2EL and LBEE5PL2DL) have been approved as Limited Modular Approval. These modules do not have a voltage stabilizing circuit in the power path to the internal RF circuitry. Therefore, the Limited Condition must provide a stable power supply for the supply voltage to the module. Please supply a stable power supply so that the voltage shown in the table below is applied. Parameter AVDD33 AVDD18 Supply Voltage VIO SD_VIO Min. 3.14 1.71 1.71 3.14 1.71 3.14 Typ. 3.3 1.8 1.8 3.3 1.8 3.3 Max. 3.46 1.89 1.89 3.46 1.89 3.46 unit V V V V Copyright Murata Manufacturing Co., Ltd. All rights reserved. 04 April 2023 13 LBES5PL2EL User Manual for FCC Trace antenna and feed line About the signal line between an antenna and a module It is a 50-ohm line design. Fine tuning of return loss etc. can be performed using a matching network. However, it is required to check "Class1 change" and "Class2 change"

which the authorities define then. The concrete contents of a check are the following three points. It is the same type as the antenna type of antenna specifications. An antenna gain is lower than a gain given in antenna specifications. The emission level is not getting worse. The following is the design of the EVB used for the test. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 04 April 2023 14 LBES5PL2EL User Manual for FCC 50-ohm line(microstrip line length) and Trace Antenna(Type2EL_Antenna) Certification tests are conducted in the following patterns. Port_ANT1

(Dedicated ANT) Port_ANT0 11.5mm m m 0

. 9 r o t c e n n o C L F U

. The 50ohm microstrip line and Type2EL_Antenna needs to be copied when module is installed in the End product. Murata provides set makers with Gerber data or something similar. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 04 April 2023 15 LBES5PL2EL User Manual for FCC About the Trace antenna and feed line of the jig where the certification test was conducted Substrate type name of certification test jig: P2ML10229 feed line width : 0.4mm Substrate thin : 0.8 0.1 mm Substrate material: FR -4 Substrate thickness between GND layer and surface layer: 0.235mm Copyright Murata Manufacturing Co., Ltd. All rights reserved. 04 April 2023 16 LBES5PL2EL User Manual for FCC Layout Guidance for Microstrip Design and External Antenna About Trace antenna(Type2EL_Antenna). The LBES5PL2EL (LBEE5PL2DL) module is certied with a PCB antenna(Type2EL_Antenna). The following precautions should be taken when using this PCB antenna(Type2EL_Antenna). Type2EL_Antenna can only be used for port_ANT0 side. When the module is installed in the final product, the 50 ohm microstrip line and Type2EL_Antenna, outlined in right red, must be copied to the state shown in the photo below where it was certified. Port_ANT1 can use the following four antennas when it is in Dedicated Usage. 146153, 219611, WT32D1-KX, W24P-U Murata provides set makers with Gerber data or something similar. Shared Antenna Usage LBES5PL2EL

(LBEE5PL2DL) Module Pin No.15 ANT0 Pin No.18 BT_15.4_IN Pin No.23 ANT1 Dedicated Antenna Usage 50ohm microstrip RF trace LBES5PL2EL

(LBEE5PL2DL) Module Pin No.15 ANT0 Pin No.23 ANT1 50ohm microstrip RF trace u.FL Connector RF Cable Type2EL_Antenna Type2EL_Antenna 146153 or 219611 or WT32D1-KX or W24P-U Copyright Murata Manufacturing Co., Ltd. All rights reserved. 04 April 2023 17 LBES5PL2EL User Manual for FCC Layout Guidance for Microstrip Design and External Antenna About Antenna with uFL connector and cables and feed lines (146153, 219611, WT32D1-KX, W24P-U). The LBES5PL2EL (LBEE5PL2DL) module is certied with four external antenna. The external antenna should be connected to the LBES5PL2EL (LBEE5PL2DL) module using 50ohm microstrip RF trace and a U.FL RF connector as shown below. The microstrip RF trace and U.FL connector are placed on the customers PCB and are external to the LBES5PL2EL (LBEE5PL2DL) module. The antenna is then connected to this u.FL Connector via a 50ohm RF adapter cable. The design of the 50ohm microstrip RF trace on the customers PCB is crucially important. Compliant operation of the LBES5PL2EL (LBEE5PL2DL) module is dependent on proper construction of this 50ohm line and the following guidelines must be followed to ensure legal operation of the product. The diagram below shows the required microstrip structure to be routed between module pin 15, 23 and the u.FL connector. The top PCB trace carries the RF energy from module to UFL connector. Shared Antenna Usage LBES5PL2EL

(LBEE5PL2DL) Module Pin No.15 ANT0 Pin No.18 BT_15.4_IN Pin No.23 ANT1 Dedicated Antenna Usage u.FL Connector RF Cable 50ohm microstrip RF trace LBES5PL2EL

(LBEE5PL2DL) Module Pin No.15 ANT0 Pin No.23 ANT1 50ohm microstrip RF trace u.FL Connector RF Cable 146153 or 219611 or WT32D1-KX or W24P-U 146153 or 219611 or WT32D1-KX or W24P-U 146153 or 219611 or WT32D1-KX or W24P-U 50ohm microstrip RF trace : Murata provides set makers with Gerber data or something similar. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 04 April 2023 18 LBES5PL2EL User Manual for FCC The Layer2 ground plane provides a return path for the circuit. The Dielectric material (along with the dimensions of the microstrip structures) determines the characteristic impedance of the microstrip transmission line. Note the representative dimensions shown in the drawing above. It is imperative that the module customer (the integrator) use the exact dimensions we recommend to ensure a 50-ohm impedance for this transmission line. The following dimensions and/or ratios should be used to set the microstrip impedance to 50ohms. Dielectric (PCB) Material We recommend standard FR4 PCB material. Other dielectrics will work but will require recalculation of microstrip dimensions. The following guidance is predicated on the use of FR4 Dielectric. If FR4 is not used for PCB material, please contact Murata to determine new dimensions for microstrip structure. H (Dielectric Height) this is the thickness of dielectric between the trace layer (layer 1) and the ground plane on layer 2. Note that layer 2 must be electrical ground. We recommend a dielectric thickness of 8-15 mils. This range provides the customer with some exibility in board construction. t (trace thickness) Microstrip impedance is not severely affected by the thickness dimension. Standard 102 or 202 copper deposition is recommended. Equivalent thickness is 1-2 mils. W (trace width) this is the crucial dimension. This width must be set correctly to obtain the desired 50 ohms impedance. When using FR-4 dielectric, the width (W) of the microstrip trace should be set to:

W = H * 1.8 Copyright Murata Manufacturing Co., Ltd. All rights reserved. 04 April 2023 19 LBES5PL2EL User Manual for FCC The Layer2 ground plane provides a return path for the circuit. The Dielectric material (along with the dimensions of the microstrip structures) determines the characteristic impedance of the microstrip transmission line. Note the representative dimensions shown in the drawing above. It is imperative that the module customer (the integrator) use the exact dimensions we recommend to ensure a 50-ohm impedance for this transmission line. The following dimensions and/or ratios should be used to set the microstrip impedance to 50ohms. Dielectric (PCB) Material We recommend standard FR4 PCB material. Other dielectrics will work but will require recalculation of microstrip dimensions. The following guidance is predicated on the use of FR4 Dielectric. If FR4 is not used for PCB material, please contact Murata to determine new dimensions for microstrip structure. H (Dielectric Height) this is the thickness of dielectric between the trace layer (layer 1) and the ground plane on layer 2. Note that layer 2 must be electrical ground. We recommend a dielectric thickness of 8-15 mils. This range provides the customer with some exibility in board construction. t (trace thickness) Microstrip impedance is not severely affected by the thickness dimension. Standard 102 or 202 copper deposition is recommended. Equivalent thickness is 1-2 mils. W (trace width) this is the crucial dimension. This width must be set correctly to obtain the desired 50 ohms impedance. When using FR-4 dielectric, the width (W) of the microstrip trace should be set to:

W = H * 1.8 Copyright Murata Manufacturing Co., Ltd. All rights reserved. 04 April 2023 20

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6756078.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Label & Location Front Side 1. 2.

Label & Location Front Side 1. 2. There is no space to describe the FCC ID/ ISED IC Number. Therefore it is described on the manual.

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: August 24, 2023 Ref: Attestation Statements Part 2.911(d)(7) Filing

[Murata Manufacturing Co., Ltd.] (the applicant) certifies that, as of the date of the filing of the application, Americas Compliance Consulting LLc dba iCertifi. is our designated U.S. agent for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Americas Compliance Consulting LLc dba iCertifi. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process. Sincerely, Designated U.S. Agent Information:

FRN: 0024753089 Name: Murata Electronics North America, Inc. Contact Person: Mark E Tucker Address: 2200 Lake Park Drive Smyma, GA 30080-7604 United States Tel.: (678)684-2009 Email: mtucker@murata.com U.S. Agent Signature:

Applicant:

FRN:0017033432 Company Name: Murata Manufacturing Co., Ltd. Grantee Code: VPY Contact Person: Kenji Hayashikoshi Address: 1-10-1, Higashikotari, Nagaokakyo-shi, Kyoto 617-8555 Japan Tel.: +81-75-955-6736 Email: koshi@murata.com Applicant Signature:

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: August 24, 2023 Ref: Attestation Statements Part 2.911(d)(5)(i)&(ii) Filing FCC ID: VPYLBES5PL2EL Statement for 47 CFR section 2.911(d)(5)(i)

[Murata Manufacturing Co., Ltd.] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Statement for 47 CFR section 2.911(d)(5)(ii)

[Murata Manufacturing Co., Ltd.] (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as a specifically named entity or any of its subsidiaries or affiliates that producing covered equipment. Sincerely, Signature: ____________________ Printed Name /Title: Kenji Hayashikoshi / Senior Manager Company Name: Murata Manufacturing Co., Ltd.

Date: August 18, 2023 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Requesting permissive change To Whom It May Concern:

The purpose of this letter is to request a Permissive change for FCC ID: VPYLBES5PL2EL, Original grant date: April 14, 2023 The major change filed under this application is 1. adds 11n-HT40 ,11ac-VHT20 ,11ac-VHT40 and 11ax-HE40 of only 2.4 GHz Sincerely,

(Signature) Name:Kenji Hayashikoshi Title:Senior Manager On behalf of: Murata Manufacturing Co., Ltd. Telephone:+81-75-955-6173 Email: koshi@murata.com

Date: August 18, 2023 Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 REQUEST FOR CONFIDENTIALITY - FCC FCC ID: VPYLBES5PL2EL Pursuant to Sections 0.457(d) and 0.459 of the Commissions Rules and FCC Guidance document 726920, we hereby request permanent confidential treatment of exhibits identified as such in the table below and request they are permanently withheld from public review based on the documents containing trade secrets and proprietary information not customarily released to the public. The public disclosure of this information might be harmful to the applicant and provide unjustified benefits to its competitors. We also request short-term confidentiality on certain exhibits until the intended date of marketing as outlined below. We request the exhibits be withheld from public view for a period of (180) days. We attest marketing of the product will only commence after the period of short-term confidentiality expires, or if marketing is to commence before the requested number of days listed above, the grantee will inform the TCB to release the Short-Term Confidentiality information withheld on the FCC equipment authorization website. Exhibit Block Diagrams Operation Description Software defined radio & security info Parts List & Placement/BOM Tune-Up Procedure Schematic Diagrams External Photos Internal Photos Test Setup Photos Users Manual Type of Confidentiality Requested Permanent Permanent Permanent Permanent Permanent Permanent

Permanent*

Permanent*

Short Term Short Term

Short Term Short Term Short Term Short Term Short Term Short Term Short Term The asterisked items (*) require further information to be provided in this justification letter before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 D01 found at:

https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. Note: any documents held under the Short-Term confidentiality will automatically become public after the requested time if an appropriate extension request has not been received. Any exhibits (i.e., schematic diagrams) that may have already been requested to have Permanent confidentiality as shown above need not be repeated under Short-Term confidentiality request. Sincerely, Signed:

Printed name: Kenji Hayashikoshi Title: Senior Manager Company Name: Murata Manufacturing Co., Ltd.

WIFI Channel 12 & 13 Declaration Letter To whom it may concern, we declare below featured for equipment authorization regarding Date: 2023/2/22 FCC ID: VPYLBES5PL2EL ISED Certification Number: 772C-LBES5PL2EL Product hardware does not have the capability to operate on channel 12 &

13. Product hardware has the capability to operate on channel 12 & 13. However , these 2 channels will be disabled via software and user will not able to enable these 2 channels. Product hardware has the capability to operate on channel 12 & 13. And meeting KDB 594280 D01 requirement. Compliance is demonstrated in test report TERF2211002513E2 as the maximum transmit power is properly adjusted to comply with the out-of-

band emission requirements in Part 15.247. The device is a WiFi client device that is not able to operate at different power levels as the default setting, which is not accessible to third-party Others Pls explain detail here. Please check Signature:

Title / Name (Printed): Kenji Hayashikoshi / Senior Manager

Attestation Date: February 22, 2023 To whom it may concern, We declare below featured for equipment authorization regarding FCC ID: VPYLBES5PL2EL The client software and associated drivers of this device will not initiate any transmission, including beacons and support for ad-hoc peer-to- peer modes, on DFS frequencies without initiation by a master. Signature:

Title / Name (Printed): Kenji Hayashikoshi / Senior Manager