FCC ID: VPYLB1EN Industrial Computer

6. Notice For OEM integration only device cannot be sold to general public. Therefore we will ask OEM to include the following statements required by FCC on the product and in the Installation manual Notice. Please describe the following warning on the final product which contains this module. Contains Transmitter Module FCC ID: VPYLB1EN Contains Transmitter Module FCC ID: VPYLB1EN or Contains FCC ID: VPYLB1EN This device complies with Part 15 of FCC Rules and Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme la partie 15 des rgles de la FCC et aux normes des CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. When the product is small, as for these words mentioned above, the posting to a manual is possible. Please describe the following warning to the manual. p FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the users p authority to operate the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. y pp g p p y y Copyright Murata Manufacturing Co., Ltd. All rights reserved. 26 June 2015 16 6. Notice When installing it in a mobile equipment. Please describe the following warning to the manual. If mobile equipment use only BT/BLE . This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). Cet q ipement est conforme a Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non ra onnements nonces po r n en ironnement non contrl et respecte les rgles les radiolectriques (RF) de la FCC lignes directrices d'exposition et dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement met une nergie RF trs faible qui est considre conforme sans valuation de lexposition maximale autorise (MPE). limites de position a In the case of conditions other than the above This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body. Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles les radiolectriques (RF) de la FCC lignes directrices d'exposition et dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement doit tre install et utilis en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain. When installing it in a portable equipment. It is necessary to take a SAR test with your set mounting this module(except to use only BT/BLE. Class II permissive change application is necessary using the SAR report. Please contact Murata. Please contact Murata. Note) Portable equipment : Equipment for which the spaces between human body and antenna are used within 20cm. Mobile equipment : Equipment used at position in which the spaces between human body and antenna exceeded 20cm. Copyright Murata Manufacturing Co., Ltd. All rights reserved. 26 June 2015 17

Dell Edge Gateway 5000 Series Installation and Operation Manual Computer Model: Dell Edge Gateway 5000 Regulatory Model: N01G Regulatory Type: N01G001 Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright 2015 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual property laws. Dell and the Dell logo are trademarks of Dell Inc. in the United States and/or other jurisdictions. All other marks and names mentioned herein may be trademarks of their respective companies. 2015 - 11 Rev. A00 Contents Overview....................................................................................... 4 System Features........................................................................... 5 System LED Lights..............................................................................................7 Setting up your Dell Edge Gateway..........................................9 Professional installation instructions.................................................................9 Instructions d'installation professionnelles.....................................................10 Federal Communication Commission Interference Statement.....................10 Industry Canada Statement..............................................................................11 Powering on the system.................................................................................. 13 Inserting a micro-SIM card.............................................................................. 14 Removing the micro-SIM card........................................................................ 15 Setting up your operating system.......................................... 16 Windows 10......................................................................................................16 Ubuntu..............................................................................................................16 Wind River Linux...............................................................................................16 Specifications............................................................................. 17 Contacting Dell..........................................................................20 3 Overview The Dell Edge Gateway 5000 series allows you to connect (wired or wireless) to network enabled devices and manage them remotely in your existing network ecosystem. The system can be either mounted on the wall using the Dell approved VESA wall mount kit or mounted into your existing rack infrastructure using the Rail mount. The system is running on Windows 10, Ubuntu, and Wind River Linux operating systems. 4 System Features Feature 1. USB 2.0 port 2. USB 2.0 port 3. HDMI port 4. Wireless antenna port Connect peripherals such as storage devices, printers, displays and so on. Provides data transfer speeds up to 480 Mbps. Connect peripherals such as storage devices, printers, displays and so on. Provides data transfer speeds up to 480 Mbps. Connect a Monitor or another HDMIin enabled device. Provides video and audio output. Connect a antenna to increase the range and strength of the wireless signals. 5 Feature 5. Intrusion detection connector Connect a TPB based security device to 6. Wireless antenna port 7. Mobile broadband antenna port 8. Micro-SIM card slot 9. Mobile broadband antenna port detect any intrusion into the system. Connect a wireless antenna to increase the range and strength of the wireless signals. Connect a antenna to increase the range and strength of the mobile broadband signals. Insert a micro-SIM card to connect to a mobile broadband network. Connect a antenna to increase the range and strength of the mobile broadband signals. 10. Power module expansion port Connect an external power module for increased power options. Connect a +24V AC/DC power Phoenix connector to provide power to your system Connect a +19.5 VDC power adapter connector to provide power to your system Press and hold for 2 seconds to turn on the system if it is turned off. Connect the grounding cable to the system Connect to a serial port enabled device like printers and so on. Connect to a CANbus port enabled device or dongles. Connect a RS422/485 cable to configure the system. Connect a RS422 cable to configure the system. Connect a RS485 cable to configure the system. 11. +24V AC/DC power Phoenix connector 12. +19.5 VDC power adapter port 13. Power button 14. Earth ground 15. Serial port 16. CANbus port 17. RS422/485 port 18. RS485 port 19. RS485 port 6 Feature 20. USB 3.0 port 21. Network port 22. Network port 23. I/O expansion port System LED Lights Connect peripherals such as storage devices, printers, displays and so on. Provides data transfer speeds up to 5 Gbps. Connect an Ethernet (RJ45) cable from a router or a broadband modem for network or internet access. Connect an Ethernet (RJ45) cable from a router or a broadband modem for network or internet access. Connect an external expansion module for additional I/O ports. Feature 1. Serial port status light 2. CANbus port status light 3. RS422/485 port status light 4. RS485 port status light 5. RS485 port status light 6. Network status light Provide the status of the serial port connection Provide the status of the CANbus port connection Provide the status of the RS422/485 port connections Provide the status of the RS485 port connections Provide the status of the RS485 port connections Indicates the connectivity status and network activity. 7 Feature 7. Network status light 8. Power status light 9. Mobile broadband status light 10. Wireless status light 11. Blutooth status light Indicates the connectivity status and network activity. Indicates the powerstate of the system. Indicates the mobile broadband status and network activity. Indicates the wireless connectivity status and network activity. Indicates the blutooth status and activity. 12. Cloud connection status light Indicates the could connection status. 8 Setting up your Dell Edge Gateway WARNING: Before you begin any of the procedures in this section, read the safety information that shipped with your system. For additional best practices information, go to www.dell.com/

regulatory_compliance. WARNING: To ensure the protection provided by Dell Edge Gateway is not impaired, do not use or install the system in any manner other than that which is specified in this manual. WARNING: Use cable appropriate for the load currents: 3-core cable rated 5 A at 90 C (194 F) minimum, which conform to either IEC 60227 or IEC 60245. The system accept;s cables from 0.8 to 2.5 mm

(18 to 14 AWG). WARNING: Use only the power adapter provided with DELL. The system should be operated only with power source of the same kind as indicated on the Power adapter rating plate. The power adapter provided is a limited power source or SELV/limited energy circuit or class 2 power source, rated output +19.5 VDC 65W, maximum operating temperature 50 C, and it is compliant to national standards of the specific country where the system is used. Do not use different type of power source. Professional installation instructions Installation personnel This product is designed for specific applications and needs to be installed by qualified personnel with RF and regulatory related knowledge. The general user shall not attempt to install or change the setting. Installation location The product shall be installed at a location where the radiating antenna is kept 20 cm from nearby persons in its normal operation condition in order to meet regulatory RF exposure requirements. External antenna Use only the antenna(s) which have been approved by the applicant. Non-

approved antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead to a violation of FCC/IC limits and is prohibited. 9 Installation procedure Please refer to users manual for the detail. WARNING: Please carefully select the installation position and make sure that the final output power does not exceed the limits set forth in relevant rules. The violation of these rules could possibly lead to serious federal penalties. Instructions d'installation professionnelles Le personnel d'installation Ce produit est conu pour des applications spcifiques et doit tre install par un personnel qualifi avec RF et connaissances connexes rglementaire . L'utilisateur ne doit pas tenter gnrale d'installer ou de modifier le rglage. Lieu d'installation Le produit doit tre install un endroit o l'antenne de rayonnement est maintenue 20 cm de personnes proximit dans son tat de fonctionnement normal , afin de rpondre aux exigences rglementaires d'exposition aux radiofrquences . Antenne externe Utilisez uniquement l'antenne (s ) qui ont t approuvs par le demandeur . Antenne ( s) peuvent produire de l'nergie RF parasite indsirable ou excessive transmission qui peut conduire une violation des normes de la FCC / IC est interdite et non - approuv. Procdure d'installation Please refer to users manual for the detail. ATTENTION: S'il vous plat choisir avec soin la position d'installation et assurez-vous que la puissance de sortie final ne dpasse pas les limites fixes dans les rgles pertinentes . La violation de ces rgles pourrait conduire des sanctions fdrales graves . Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 10 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to Increase the separation between the equipment and receiver. which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. NOTE: Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only. Industry Canada Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1 2 this device may not cause interference, and this device must accept any interference, including interference that may cause undesired operation of the device. 11 Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

1 2 l'appareil ne doit pas produire de brouillage, et l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. This device complies with RSS-310 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference. Cet appareil est conforme la norme RSS-310 d'Industrie Canada. L'opration est soumise la condition que cet appareil ne provoque aucune interfrence nuisible. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter, except tested built-in radios. Cet appareil et son antenne ne doivent pas tre situs ou fonctionner en conjonction avec une autre antenne ou un autre metteur, exception faites des radios intgres qui ont t testes. The County Code Selection feature is disabled for products marketed in the US/ Canada. La fonction de slection de l'indicatif du pays est dsactive pour les produits commercialiss aux tats-Unis et au Canada. Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations: Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Caution:

1 The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

12 2 3 4 5 The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the eirp limit;

and The maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the eirp limits specified for point-to-point and non point-to-point operation as appropriate. The worst-case tilt angle(s) necessary to remain compliant with the eirp elevation mask requirement set forth in Section 6.2.2(3) shall be clearly indicated. Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement:

les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

le gain maximal dantenne permis pour les dispositifs utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer la limite de p.i.r.e.;

le gain maximal dantenne permis (pour les dispositifs utilisant la bande 5725-5825 MHz) doit se conformer la limite de p.i.r.e. spcifie pour lexploitation point point et non point point, selon le cas. les pires angles dinclinaison ncessaires pour rester conforme lexigence de la p.i.r.e. applicable au masque dlvation, et nonce la section 6.2.2 3), doivent tre clairement indiqus. De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. 1 2 3 4 5 Powering on the system 1 Install the Dell Edge Gateway on the wall mount using the Dell approved VESA mounting kit. or Install the Dell Edge Gateway on the rack infrastructure using the Dell approved rail mounting kit. 13 2 Connect the network cable. or Install the wireless antenna to enable the wireless connections 3 Connect a display to the system. 4 Connect a keyboard and mouse if accessing the system directly. 5 Connect a SELV/limited energy circuit power source to the Dell Edge Gateway. 6 Connect a grounding cable to the system if required. 7 8 Press the power button to power on the computer. Is setting up the system for the first time, complete the operating system setup. NOTE: The Dell Edge Gateway is shipped with either Windows 10, Ubunttu, or Wind River Linux operating systems. 9 Connect and configure to devices using the RS422/RS485 ports. NOTE: Turn on the corresponding dip switches to enable the corresponding RS422/R485 ports. Inserting a micro-SIM card CAUTION: It is recommended to insert the micro-SIM card before powering on the Dell Edge Gateway. Locate the micro-SIM card slot. 1 2 Using a paper clip or SIM eject tool eject the micro-SIM card tray. 3 Place the micro-SIM card on the tray. CAUTION: Ensure that the micro-SIM card is aligned as shown in the image. 14 4 Close the micro-SIM card tray. Removing the micro-SIM card CAUTION: Removing the micro-SIM card while it is in use may cause data loss or result in application errors. 1 Using a paper clip or SIM eject tool eject the micro-SIM card tray. 2 Remove the micro-SIM card out of the micro-SIM card tray. 3 Replace the micro-SIM card tray into the system. 15 Setting up your operating system Windows 10 NOTE: For more information on setting up your Windows 10 operating system, see www.dell.com/support/windows. 1 Power on the system. The Windows configuration screen appears. Setup the wireless connection for your system. 2 3 Create a local or Microsoft account. The Windows 10 setup is complete. Ubuntu NOTE: For more information on setting up your Ubuntu operating system, see www.ubuntu.com/support. 1 2 3 Power on the system. The Ubuntu configuration screen appears. Setup the wireless connection for your system. Enter your login and password. The Ubuntu operating system is setup. Wind River Linux NOTE: For more information on setting up your Wind River operating system, see http://www.windriver.com/support. 1 2 Power on the system. The Wind River splash screen is displayed after the Dell Edge Gateway boots completes POST. The operating system will take around twenty seconds to complete the loading process. Enter the login information. 3 Activate your Wind River operating system installation. The Wind River operating system is setup. 16 Specifications System information Product Name Processor Operating system RAM Storage Memory Type Speed Industrial control equipment 6th Generation Intel Core i7 Windows 10 Ubuntu Wind river linux with Moon Island 3.0 stack LPDDR3 32 GB SSD 64 GB SSD LPDDR3 1600 MHz Configurations supported 2 GB, 4 GB, and 8 GB Ports and connectors Audio/video microSD card Network One HDMI port One microSD-card slot Two RJ45 ports Two wireless antenna ports Two mobile broadband antenna ports One CANbus port One RS422/485 combo port Two RS485 port USB One USB 3.0 port 17 Ports and connectors Serial port One Serial port Two USB 2.0 ports Communications Wi-Fi Bluetooth Dual-band 802.11b/g/n/ac Bluetooth 4.1 LE Power requirements Phoenix connector input voltage/

current 24 VAC or 24 VDC / 4A Power adapter input voltage/current 19.5 VDC / 3.33A Phoenix connector Input frequency 50 Hz60 Hz Temperature range:

Operating Storage Environmental requirements Temperature range:

0C to 50C (32F to 122F) 40C to 70 C (40F to 158F) Operating Non-operating 0C to 50C (32F to 122F)

-40C to 65 C (-40F to 149 F) Relative humidity (maximum):

Operating Non-operating 10% to 90% (non-condensing) 5% to 95% (non-condensing) Altitude (maximum, unpressurized):

Operating Storage

-15.20 m to 3048 m (-50 ft to 10,000 ft)

-15.20 m to 10,668 m (-50 ft to 35,000 ft) 18 19 Contacting Dell To contact Dell for sales, technical assistance, or customer service issues:

1 Go to www.dell.com/contactdell. 2 Verify your country or region in the Choose a Country/Region drop-

down list at the bottom of the page. Select the appropriate service or support link based on your requirement or choose the method of contacting Dell that is convenient for you. Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. NOTE: If you do not have an active internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. 3 20

Installation and Operation Manual Regulatory Model: N01PC Regulatory Type: N01PC001 Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Overview The Dell Embedded Box PC 5000 series allows you to connect (wired or wireless) to network enabled devices and manage them remotely in your existing network ecosystem. The system can be either mounted on the wall using the Dell approved wall mount kit or mounted into your existing rack infrastructure using the Rail mount. The system is running on Windows 10, Ubuntu, and Wind River Linux operating systems. System Features Top - View Feature Expansion-card slot 1 Expansion-card slot 2 Power button Remote power switch Hard reset USB 3.0 port (4) Network port (2) DisplayPort (2) HDMI port CANbus port VGA port

+19.5 VDC power port (barrel connector) Audio ports (3)

+24V DC power Phoenix connector Connect a +24V DC power Phoenix connector to provide power to your system Supports an optional PCIe discrete graphics solution, 20-25W(12V/2A) graphics card and 10W thermal capability. Supports an optional PCIe discrete graphics solution, 20-25W(12V/2A) graphics card and 10W thermal capability. Press and hold for 2 seconds to turn on the system if it is turned off. Install a remote power switch Press and hold to hard reset the system Connect peripherals such as storage devices, printers, displays and so on. Provides data transfer speeds up to 5 Gbps. Connect an Ethernet (RJ45) cable from a router or a broadband modem for network or internet access. Connect a Monitor or another DisplayPort enabled device. Provides video and audio output. Connect a Monitor or another HDMIin enabled device. Provides video and audio output. Connect to a CANbus port enabled device or dongles. Connect a monitor or another VGA enabled device. Provides video output. Connect a +19.5 VDC power connector to provide power to your system Connect a speaker, a headphone, a microphone, or a headphone and microphone combo (headset). 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Bottom - View Feature 1 2 3 GPIO-in 9 pin port GPIO-out 9 pin port USB 2.0 port (4) Network status light Power status light Hard-drive activity light Network status light Mobile broadband antenna port 2 RS232 port 4 4 5 6 7 8 9 10 Mobile broadband antenna port 1 11 12 13 Wireless antenna port 2 14 15 Wireless antenna port 1 RS232 port 3 RS232 port 2 RS232 port 1 Connect to a GPIO-out enabled device or dongles Connect to a GPIO-in enabled device or dongles Connect peripherals such as storage devices, printers, displays and so on. Provides data transfer speeds up to 480 Mbps. Indicates the connectivity status and network activity of the network port one. Indicates the powerstate of the system. Turns on when the system reads from or writes to the hard drive. Indicates the connectivity status and network activity of the network port two. Connect an antenna to increase the range and strength of the mobile broadband signals. Connect a RS232 cable to configure the system. Connect an antenna to increase the range and strength of the mobile broadband signals. Connect a RS232 cable to configure the system. Connect a RS232 cable to configure the system. Connect a wireless antenna to increase the range and strength of the wireless signals. Connect a RS232 cable to configure the system. Connect a wireless antenna to increase the range and strength of the wireless signals. Setting up your Dell Embedded Box PC 5000 WARNING: When installing the system, the responsible party or integrator shall use the AC Adapter provided with the system, or connect to a 12-26 Vdc power source already present as part of the clients installation If ambient temperature of the installation exceeds 40'C then use the 12-26 Vdc power available as part of the installation. Always make sure that the available power source matches the required input power of the system, check the input power markings next to power connector(s) before making connections. WARNING: Before you begin any of the procedures in this section, read the safety information that shipped with your system. For additional best practices information, go to www.dell.com/regulatory_compliance. WARNING: To ensure the protection provided by the system is not impaired, do not use or install the system in any manner other than that which is specified in this manual. WARNING: Use cable appropriate for the load currents: 3-core cable rated 5 A at 90 C (194 F) minimum, which conform to either IEC 60227 or IEC 60245. The system accepts cables from 0.8 to 2.5 mm (18 to 14 AWG). WARNING: Use only the power adapter provided with DELL. The system should be operated only with power source of the same kind as indicated on the Power adapter rating plate. WARNING: The symbol indicates hot surface or adjacent hot surface that can obtain temperature during normal use that can cause a burn. Allow equipment to cool off or use protective gloves when handling to reduce risk of a burn. Professional installation instructions Installation personnel This product is designed for specific applications and needs to be installed by qualified personnel with RF and regulatory related knowledge. The general user shall not attempt to install or change the setting. Installation location The product shall be installed at a location where the radiating antenna is kept 20 cm from nearby persons in its normal operation condition in order to meet regulatory RF exposure requirements. External antenna Use only the antenna(s) which have been approved by the applicant. Non-approved antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead to a violation of FCC/IC limits and is prohibited. Installation procedure Please refer to users manual for the detail. WARNING: Connect power to only one of the two power connection ports, either Phoenix Connector or the Barrel Connector. Connection of two power sources may damage equipment and present risk of fire. Powering on the system WARNING: Connect power to either Phoenix Connector or the Barrel Connector only. Connecting to both power sources may damage equipment and present a fire risk. 1. Install the system on the wall mount using the Dell approved wall mounting kit. or Install the system on the rack infrastructure using the Dell approved DIN-rail mounting brackets. 2. Connect the network cable. or Install the wireless antenna to enable the wireless connections 3. Connect a display to the system. 4. Connect a keyboard and mouse if accessing the system directly. 5. Connect a SELV power source to the system 6. Press the power button to power on the computer. If setting up the system for the first time, complete the operating system setup. 7. Connect and configure to devices using the RS422/RS485 ports. Mounting the system on the wall You can mount the system on a wall by using mounting brackets. The brackets secure the system to the wall. NOTE: Images below are for illustrative purpose only. 1. Secure the two mounting brackets to the rear of the system by using eight screws. 2. Drill four holes in the wall that correspond to the holes in the mounting bracket, then place the system against the wall and align the holes in the mounting brackets with the holes in the wall. 3. Tighten the screws to secure the system to the wall. One HDMI port One VGA port Two DisplayPort One line-in port One line-out port One microphone port One microSD-card slot Two RJ45 ports Two wireless antenna ports Two mobile broadband antenna ports One CANbus port Specifications Ports and connectors Audio/video microSD card Network USB Communications Wi-Fi Bluetooth Four RS232 port Four USB 3.0 port Two USB 2.0 ports Dual-band 802.11b/g/n/ac Bluetooth 4.1 LE Power requirements Phoenix connector input voltage/current Power input voltage/current 12-26V 10.8A-5A (130W) 12-26V 10.8A-5A (130W) WARNING: Connect power to either Phoenix Connector or the Barrel Connector only. Connecting to both power sources may damage equipment and present a fire risk. Environmental requirements Temperature range:

Operating Non-operating Relative humidity (maximum):

Operating Non-operating Altitude (maximum, unpressurized):

Operating Non-operating 0C to 50C (32F to 122F)

-45C to 65C (-49F to 149F) 10% to 90% (non-condensing) 5% to 95% (non-condensing)

-15.20 m to 5000 m (-50 ft to 16,404 ft)

-15.20 m to 10,668 m (-50 ft to 35,000 ft)

FCC Radio Frequency (RF) Exposure Information This device has been evaluated to, and shown to be compliant with, the FCC Radio Frequency

(RF) exposure limits. Devices such as Desktop computers and Access Points (AP) that contain wireless functions (such as 802.11, Bluetooth, 3G or 4G) must be installed to provide a separation distance of at least 20cm from people to ensure compliance with the RF exposure requirements. Certain laptop/notebook computers, with antennas located toward the top of the screen, may require a separation distance of at least 20cm between the antennas and persons when they are operating to ensure compliance with the RF exposure requirements. These laptop/notebook computers are designed such that, during normal use with the screen open, the antenna-to-user distance is greater than 20cm. Some devices may have additional requirements for operating conditions to ensure compliance with RF exposure requirements. Specific instructions, where required, will be contained in the manual for that device. Please read your operating manual carefully. Interference Statement This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer's instruction manual, may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Notice: The FCC regulations provide that changes or modifications not expressly approved by Dell Inc. could void your authority to operate this equipment. These limits are designed to provide reasonable protection against harmful interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference with radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures:

Reorient the receiving antenna. Relocate the system with respect to the receiver. Move the system away from the receiver. Plug the system into a different outlet so that the system and the receiver are on different branch circuits. If necessary, consult a representative of Dell Inc. or an experienced radio/television technician for additional suggestions. NOTE: Any additional Wireless module must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. Any other unauthorized installation or use will violate FCC Part 15 regulations. Modifications not expressly approved by Dell could void your authority to operate the equipment.