FCC ID: VPYLB2GT LoRa Module

LoRa Module User Manual Part Number: LBAA0XV2GT LBAA0XV2GT has been FCC/ISED certified as Single Modular Approval with the following IDs. FCC ID: VPYLB2GT IC: 772C-LB2GT 218-230222 The module is limited to OEM installation ONLY. The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module. Therefore, the final host product must be submitted to Murata for confirmation that the installation for the module into the host is in compliance with regulations of FCC and IC Canada. Specially, if an antenna other than the model documented in the Filing is used, a Class 2 Permissive Change must be filed with the FCC. Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment. This module has been approved by FCC to operate with the antenna types with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. The following antenna has been certified in combination with the module. Refer to the next pages for the antenna application guidance. Whip antenna by Linx with peak gains as 2.5dBi for 2.4GHz ISM band Whip antenna by TE with peak gain as 2.0dBi for the sub-GHz band Antenna Application Guidance 2.4GHz antenna P/N: ANT-DB1-RAF-RPS Sub-GHz antenna P/N: 001-0002 Antenna Application Guidance RP-SMA connector for Sub-GHz antenna RP-SMA connector for 2.4GHz antenna Length: 18.55 mm Width: 0.34 mm Length: 24.12 mm Width: 0.34 mm PCB for assembly the antenna FCC Statements Please take attention that changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body. When the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording Contains transmitter module FCC ID: VPYLB2GT or Contains FCC ID:

VPYLB2GT. FCC Statements (cont.) When the module is installed inside another device, the user manual of this device must contain below warning statements:

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. The host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. The end user manual shall include all required regulatory information/warning as shown in this manual, include:

This product must be installed and operated with a minimum distance of 20 cm between the radiator and user body. IC Statements This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorise aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. IC Statements (cont.) This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. ce matriel est conforme aux limites de dose d'exposition aux rayonnements, FCC / CNR-102 nonce dans un autre environnement.cette eqipment devrait tre install et exploit avec distance minimale de 20 entre le radiateur et votre corps. When the Industry Canada certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can be use wording Contains transmitter module IC: 772C-

LB2GT or Contains IC: 772C-LB2GT.

Company: Murata Manufacturing Co., Ltd. Add: 10-1, Higashikotari 1-chome, Nagaokakyo-shi, Kyoto 617-8555, Japan Tel: 81-75-955-6736 Fax: 81-75-955-6634 Label Location Justification Letter This justification is applicable to the LoRa Module identified as:

Model: LBAA0XV2GT FCC ID: VPYLB2GT Since the module is too small to put the FCC ID even with the font size 4 points, we have to put the FCC ID on the user manual and packaging. Module appearance The module size is 9.98*8.70mm. There is not enough space to put the FCC ID besides other mandatory marking information. 8.70mm 9.98mm Label of certification IDs Anti-humidity Plastic Bag Desiccant Humidity Indicator FCC ID on the packaging A label of certification IDs is sticking on the anti-humidity bag. Label Model: LBAA0XV2GT FCC ID: VPYLB2GT IC: 772C-LB2GT Sincerely Yours, Signature:

Typed or Printed Name: Kenji Hayashikoshi Title: Dev. Sec. 6 Senior Manager Connectivity Module Dev. Dept. Communication Module Div.

3/14/2024 Nemko North America, Inc. 303 River Road Ottawa, Ontario, Canada K1V 1H2 REQUEST FOR CONFIDENTIALITY - FCC FCC ID: VPYLB2GT Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commissions Rules and FCC Guidance document 726920, we hereby request confidential treatment of information accompanying this application as outlined below:

PERMANENT LONG-TERM CONFIDENTIALITY:

Schematics Bill of Materials/Parts List Block Diagrams Theory of Operation When the device is marketed before the requested number of days listed above, the grantee will inform the TCB to release the Short-Term Confidentiality information withheld on the FCC equipment authorization website. The above information contains trade secrets and proprietary information not customarily released to the public. The public disclosure of this information might be harmful to the applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Sincerely, Signed:

Printed name: KENJI HAYASHIKOSHI Title: SENIOR MANAGER

Covered Equipment Certification Attestation Letter 3/14/2024 Nemko North America, Inc. 303 River Road Ottawa K1V 1H2 Canada ATTN.: Reviewing Engineer FCC ID: VPYLB2GT Murata Manufacturing Co., Ltd. (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not covered equipment. Murata Manufacturing Co., Ltd. (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Signed:

Printed name: KENJI HAYASHIKOSHI Title: SENIOR MANAGER Company Name: Murata Manufacturing Co., Ltd. Date: 3/14/2024

Date (19/03/2024) Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Modular Approval Request FCC ID:VPYLB2GT The following attestation addresses the requirements to support modular approval:

Modular approval requirement Yes (provide brief statement) No *

(a) The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly

(b) The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal

(c) The module must contain power supply regulation on the module

(d) The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per Sections 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b)

(e) The module must demonstrate compliance in a stand-alone configuration

(f) The module must be labelled with its permanently affixed FCC ID label, or use an electronic display (See KDB Publication 784748 about labelling requirements)

(g) The module must comply with all specific rules applicable to the transmitter. The grantee must provide comprehensive instructions to explain compliance requirements Refer to external photos. This module has shield cover. All inputs to the modules are buffered through logic or microprocessor inputs. Refer to Schematics. management The Module uses the chip with built-in power components, the ratedpower is 3.3V Refer to schematics. module power, The modular transmitter has two Dipole antenna, Refer to External photo. The modular transmitter is connected to the controlled board when testing. Please refer to setup photo. Refer to the label. Refer to manual Modular approval requirement Yes (provide brief statement)

(h) The module must comply with RF exposure requirements The EUT meets RF exposure evaluation 2.1091, If the device built into a host as a portable usage, the additional RF exposure evaluation may be required as specified by 2.1093

* Please provide a detailed explanation if the answer is No. Sincerely, No *

Signed:

Printed name: Kenji Hayashikoshi Title: Dev. Sec. 6 Manager, Connectivity Module Dev. Dept., Communication Module Div.

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: March 3, 2023 Ref: Attestation Statements Part 2.911(d)(7) Filing

[Murata Manufacturing Co., Ltd.] (the applicant) certifies that, as of the date of the filing of the application, [Murata Electronics North America, Inc.] is our designated U.S. agent for service of process.[Murata Manufacturing Co., Ltd.] accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment.

[Murata Electronics North America, Inc.] accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process. Sincerely, Designated U.S. Agent Information:

Name: Murata Electronics North America, Inc. FRN: 0024753089 Contact Person: Mark E Tucker Address: 2200 Lake Park Drive Smyma, GA 30080-7604 United States Tel.: (678)684-2009 Email: mtucker@murata.com Mark E. Tucker 3/3/2023 U.S. Agent Signature:

Applicant:

Company Name: Murata Manufacturing Co., Ltd. Contact Person: Kenji Hayashikoshi Address: 10-1, Higashikotari 1-chome, Nagaokakyo-shi, Kyoto 617-8555 Japan Tel.: +81-75-955-6736 Email: mhayashi@murata.com Applicant Signature: