FCC ID: VPYLB2DT LoRa+Wi-Fi+GNSS Module

LoRa+Wi-Fi+GNSS Module User Manual Part Number: LBAA0XV2DT LBAA0XV2DT has been FCC/ISED certified as Single Modular Approval with the following IDs. FCC ID: VPYLB2DT IC: 772C-LB2DT The module is limited to OEM installation ONLY. The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module. Therefore, the final host product must be submitted to Murata for confirmation that the installation for the module into the host is in compliance with regulations of FCC and IC Canada. Specially, if an antenna other than the model documented in the Filing is used, a Class 2 Permissive Change must be filed with the FCC. Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment. This module has been approved by FCC to operate with the antenna types with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. The following antenna has been certified in combination with the module. Refer to the next pages for the antenna application guidance. Triband chip antenna by ignion with peak gains as 0.3dBi for LoRa, 3.6dBi for Wi-Fi, and 1.8dBi for GNSS;

Antenna Application Guidance Antenna placement Antenna Application Guidance PCB drawing for the antenna Contact Murata for the DXF file FCC Statements Please take attention that changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm the radiator & your body. between When the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording Contains transmitter module FCC ID: VPYLB2DT or Contains FCC ID:

VPYLB2DT. FCC Statements (cont.) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help The module is limited to installation in mobile or fixed application according to FCC rule part 2.1091 The separate approval is required for all other operating configurations including portable configurations with respect to FCC rule part 2.1093. IC Statements This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorise aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. IC Statements (cont.) This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between theradiator & your body. matriel est ce autre dans un 20cm entre le limites aux conforme environnement.cette et radiateur votre corps. de dose eqipment d'exposition tre devrait aux install rayonnements, FCC / CNR-102 et exploit avec distance nonce de minimale When the Industry Canada certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can be use wording Contains transmitter module IC: 772C-

LB2DT or Contains IC: 772C-LB2DT.

Company: Murata Manufacturing Co., Ltd. Add: 10-1, Higashikotari 1-chome, Nagaokakyo-shi, Kyoto 617-8555, Japan Tel: 81-75-955-6736 Fax: 81-75-955-6634 Label Location Justification Letter This justification is applicable to the LoRa+Wi-Fi+GNSS Module identified as:

Model: LBAA0XV2DT FCC ID: VPYLB2DT Since the module is too small to put the FCC ID even with the font size 4 point, according to the FCC Regulation and Guidance (KDB Publication 784748 D01 v09r01) which allows the FCC ID to be moved onto the user manual and packaging if the device is unquestionably too small for the FCC ID to be printed, we have to put the FCC ID on the user manual and packaging. Module size The module size is 9.98*8.70mm. There is not enough space to put the FCC ID besides other mandatory marking information. 8.70mm 9.98mm FCC ID on the packaging Label of certification IDs Desiccant Humidity Indicator Label Anti-humidity Plastic Bag A label of certification IDs is sticking on the anti-humidity bag. Model: LBAA0XV2DT FCC ID: VPYLB2DT IC: 772C-LB2DT Sincerely Yours, Signature:

Printed Name: Kenji Hayashikoshi Title: Dev. Sec. 6 Senior Manager Connectivity Module Dev. Dept. Communication Module Div.

Murata Manufacturing Co., Ltd. 10-1, Higashikotari 1-chome, Nagaokakyo-shi, Kyoto 617-8555, Japan Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date:04/03/2024 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: VPYLB2DT Murata Manufacturing Co., Ltd. (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely,

(Applicant signature) KENJI HAYASHIKOSHI Rev 1/26/2023 Murata Manufacturing Co., Ltd. 10-1, Higashikotari 1-chome, Nagaokakyo-shi, Kyoto 617-8555, Japan Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date:

Ref:

FCC ID:

Murata Manufacturing Co., Ltd. (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing covered equipment. Sincerely,

(Applicant signature) KENJI HAYASHIKOSHI 04/03/2024 Attestation Statements Part 2.911(d)(5)(ii) VPYLB2DT Filing Rev 1/26/2023

Murata Manufacturing Co., Ltd. Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: VPYLB2DT. Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type File Name Operational Description Operation Description.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. SHORT TERM CONFIDENTIALITY FOR A PERIOD OF 180 DAYS Pursuant to DA04-1705 June 15, 2004 of the Commissions public notice, we also request temporary confidential treatment of information accompanying this application as outlined below:

Exhibit Type Test Setup Photos, Manual) File Name TestSetup Photos.pdf Manual.pdf Sincerely,

(signature)

(printed name) KENJI HAYASHIKOSHI Rev 11/20/07

Murata Manufacturing Co., Ltd. Change Statement Name of manufacturer: Murata Manufacturing Co., Ltd. Address: 10-1, Higashikotari 1-chome, Nagaokakyo-shi, Kyoto 617-8555, Japan Product Name: LoRa+Wi-Fi+GNSS Module Model Number: LBAA0XV2DT TrademarkMurata This update is based on the original FCC ID and IC:

Original Name of manufacturer: Murata Manufacturing Co., Ltd. Original Address: 10-1, Higashikotari 1-chome, Nagaokakyo-shi, Kyoto 617-8555, Japan Original Product NameLoRa+Wi-Fi+GNSS Module Original Model Number: LBAA0XV2DT Original TrademarkMurata Original FCC ID: VPYLB2DT issuing date:2023.11.6 Original IC: 772C-LB2DT issuing date:2023.11.15 Only two modes were added through software. Add two new modes as listed below.There are no changes to the product.Everything else has remained unchanged Murata Manufacturing Co., Ltd. Signature KENJI HAYASHIKOSHI Full Printed Name N/A Title 2024/4/3 Date of issue

ID:

Concern:

2024/04/03 VPYLB2DT Murata Manufacturing Co., Ltd. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Date:

SUBJECT: FCC To Whom It May We, the undersigned, hereby authorize ____ DEKRA Testing and Certification (Suzhou) Co., Ltd Yingfei Wang _at No.99 Hongye Rd., Suzhou Industrial Park, Suzhou, 215006, Jiangsu, China _ on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by ___ DEKRA Testing and Certification

(Suzhou) Co., Ltd _ YingfeiWang ____ on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, _________

(Must be signed by the person that is listed on the FCC Website) C:\Users\A162642\Desktop\Dekra ()\000 \0000 \TIMCO\2331052R \10.27comments\2.POA_Letter.docx

Murata Manufacturing Co., Ltd. 10-1, Higashikotari 1-chome, Nagaokakyo-shi, Kyoto 617-8555, Japan Kyoto, Japan Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2023-03-03 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID or Grantee Code: [VPYLB2DT]

Applicant FRN: [0017033432]

[Murata Manufacturing Co., Ltd.] (the applicant) certifies that, as of the date of the filing of the application, [Murata Electronics North America, Inc.] is our designated U.S. agent for service of process for the above referenced FCC ID. [Murata Manufacturing Co., Ltd.] accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment.

[Murata Electronics North America, Inc.] accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information:

Name: [Murata Electronics North America, Inc.]

U.S. Agent FRN: [0024753089]

Address: [2200 Lake Park Drive Smyma, GA 30080-7604 United States]

Contact Person: [Mark E Tucker]

Tel.: [(678)684-2009]

Email: [mtucker@murata.com]

Sincerely,

[Murata Manufacturing Co., Ltd.]

[KENJI HAYASHIKOSHI]

[Murata Electronics North America, Inc.]

[Mark E Tucker]

3/3/2023 Rev 1/26/2023

Murata Manufacturing Co., Ltd. 10-1, Higashikotari 1-chome, Nagaokakyo-shi, Kyoto 617-8555, Japan Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 10/11/2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: VPYLB2DT Murata Manufacturing Co., Ltd. (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely,

(Applicant signature) KENJI HAYASHIKOSHI Rev 1/26/2023 Murata Manufacturing Co., Ltd. 10-1, Higashikotari 1-chome, Nagaokakyo-shi, Kyoto 617-8555, Japan Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 10/11/2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: VPYLB2DT Murata Manufacturing Co., Ltd. (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing covered equipment. Sincerely,

(Applicant signature) KENJI HAYASHIKOSHI Rev 1/26/2023

Date (27/10/2023) Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Modular Approval Request FCC ID:VPYLB2DT The following attestation addresses the requirements to support modular approval:

Modular approval requirement Yes (provide brief statement) No *

(a) The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly

(b) The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal

(c) The module must contain power supply regulation on the module

(d) The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per Sections 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b)

(e) The module must demonstrate compliance in a stand-alone configuration

(f) The module must be labelled with its permanently affixed FCC ID label, or use an electronic display (See KDB Publication 784748 about labelling requirements)

(g) The module must comply with all specific rules applicable to the transmitter. The grantee must provide comprehensive instructions to explain compliance requirements Refer to external photos. This module has shield cover. All inputs to the modules are buffered through logic or microprocessor inputs. Refer to Schematics. The Module uses the chip SX1262 with built-in power management components, the module ratedpower is 3.3V power, Refer to schematics. The modular transmitter has a PCB antenna/FPC antenna with IPEX connector and chip antenna arrangement for LoRa, Refer to External photo. The modular transmitter is connected to the controlled board when testing. Please refer to setup photo. Refer to the label. Refer to manual Modular approval requirement Yes (provide brief statement) No *

(h) The module must comply with RF exposure requirements The EUT meets RF exposure evaluation 2.1091, If the device built into a host as a portable usage, the additional RF exposure evaluation may be required as specified by 2.1093

* Please provide a detailed explanation if the answer is No. Sincerely, Signed:

Printed name: Kenji Hayashikoshi Title: Dev. Sec. 6 Manager, Connectivity Module Dev. Dept., Communication Module Div.