Preliminary Specification Number : SP-ABR-105-A WLAN Module Data Sheet MP P/N: CMWC1ZZABR Preliminary & Confidential
< Specification may be changed by Murata without notice >
Murata (China) Investment Co., Ltd. Preliminary Specification Number : SP-ABR-105-A Revision History Revision Code Draft A Date 2015-4-27 2019-11-14 Description Comments Draft 1. Revised label marking Preliminary & Confidential
< Specification may be changed by Murata without notice >
Murata (China) Investment Co., Ltd. Preliminary Specification Number : SP-ABR-105-A Contents 1. Scope ................................................................................................................................................. 1 2. Part Number / Part Composition ..................................................................................................... 1 3. Block Diagram ................................................................................................................................... 1 4. Construction, Dimensions, Marking and Terminal Configurations ............................................ 2 4.1 Construction ................................................................................................................................. 2 4.2 Dimensions (in mm) ..................................................................................................................... 2 4.3 Label Marking .............................................................................................................................. 2 4.4 Pin assignment (top view)............................................................................................................ 3 4.5 Recommended land pattern ........................................................................................................ 4 4.6 Pin description ............................................................................................................................. 5 4.7 Configuration pins ........................................................................................................................ 6 5. Range ................................................................................................................................................. 6 5.1 Absolute maximum rating (Ta=25, Z=50ohm) .......................................................................... 6 5.2 Operating conditions .................................................................................................................... 6 6. RoHS Compliance ............................................................................................................................. 6 7. RF Characteristics for IEEE802.11 .................................................................................................. 7 8. Power Up Sequence ......................................................................................................................... 7 9. Electrical Characteristics ................................................................................................................. 7 9.1 I/O Static Ratings, 3.3V ............................................................................................................... 7 9.2 Clock Specifications (optional) .................................................................................................... 8 RC32K Specifications .............................................................................................................. 8 9.2.1 9.2.2 Crystal Specifications (32.768kHz) .......................................................................................... 8 10. Reference Circuit .............................................................................................................................. 8 11. PCB Antenna Layout Guidance ...................................................................................................... 9 12. Package ........................................................................................................................................... 10 Preliminary & Confidential
< Specification may be changed by Murata without notice >
Murata (China) Investment Co., Ltd. Preliminary Specification Number: SP-ABR-105-A P. 1/14 1. Scope This product specification is applied to the IEEE802.11b/g/n WLAN module used for consumer applications. Module size Chipset Interface Reference Clock ROM Antenna Certification MSL RoHS
: 22.0 x 19.0 x 2.4 (typ) mm
: Marvell 88MW300
: UART, GPIO
: Internal (external optional sleep clock)
: SPI Flash on module (2Mbytes)
: Integrated PCB antenna
: FCC/CE/IC
: 3
: This module is compliant with the RoHS directive
*This module delivered with pre-programmed generic software as Serial Network Interface Controller. 2. Part Number / Part Composition Sample Part Number CMWC1ZZABR-TEMP MP Part Number CMWC1ZZABR Preliminary & Confidential
< Specification may be changed by Murata without notice >
Murata (China) Investment Co., Ltd. Preliminary Specification Number: SP-ABR-105-A P. 2/14 3. Construction, Dimensions, Marking and Terminal Configurations 3.1 Construction B Top view L C I Bottom view Pin.1 indicator A D E F G H QR code W Model: ABR FCC ID: VPYCMWC1ZZABR IC: 772C-CMWC1ZZABR 3.2 Dimensions (in mm) Mark L W T 3.3 Label Marking J Min. 21.8 18.8
Typ. 22 19 2.4 Max. 22.2 19.2 2.55 Mark Name A B C D E F G H I J Pin.1 indicator Murata logo Model Name / P/N FCC certification ID IC certification ID Inspection code Sub type number: 105 Version code: blank (Ver. 1.0) 2D barcode (MAC address) CE mark Preliminary & Confidential
< Specification may be changed by Murata without notice >
Murata (China) Investment Co., Ltd. Preliminary Specification Number: SP-ABR-105-A P. 3/14 3.4 Pin assignment (top view) 4. QR code 1 2 3 4 5 6 7 8 9 10 11 12 13 37 36 35 34 33 32 31 30 29 28 27 26 25 QR code Model: ABR FCC ID: VPYCMWC1ZZABR IC: 772C-CMWC1ZZABR 14 15 16 17 18 19 20 21 22 23 24 Preliminary & Confidential
< Specification may be changed by Murata without notice >
Murata (China) Investment Co., Ltd. Preliminary Specification Number: SP-ABR-105-A P. 4/14 4.1 Recommended land pattern Antenna area Preliminary & Confidential
< Specification may be changed by Murata without notice >
Murata (China) Investment Co., Ltd. Preliminary Specification Number: SP-ABR-105-A P. 5/14 4.2 Pin description No. Name Function 1 2 3 4 5 6 7 8 9 GPIO_16 CON[5]: Configuration Bit RESET_N Module Reset (active low) GPIO_22 NC GPIO_23 Functional Button Pin (optional) GPIO_24 NC GND GPIO_25 32.768 kHz Crystal Input / Oscillator Input GPIO_26 32.768 kHz Crystal Output GND 10 GPIO_27 CON[4]: Configuration Bit 11 GPIO_39 NC 12 GND 13 VDD33 3.3V DC Power Supply 14 GPIO_40 LED_1: Module Status Indication (optional) 15 GPIO_41 LED_2: Link Status Indication (optional) 16 GPIO_42 17 GPIO_43 18 GPIO_44 19 GIPO_45 20 GND 21 GPIO_46 22 GPIO_47 NC NC NC NC NC NC 23 GPIO_48 Debug Log (optional) 24 GPIO_49 NC 25 GPIO_0 UART CTS (optional) 26 GPIO_1 UART RTS (optional) 27 GPIO_2 UART Transmit 28 GPIO_3 UART Receive 29 GND 30 GPIO_4 31 GPIO_5 32 GND NC NC 33 GPIO_6 TDO: JTAG Test Data (optional) 34 GPIO_7 TCK: JTAG Test Clock (optional) 35 GPIO_8 TMS: JTAG Controller Select (optional) 36 GPIO_9 TDI: JTAG Test Data (optional) I/O I/O I I I O I/O P O O O I O O I O I I/O I MW300 Pin MW300 Pin No. Function 30 35 36 37 38 39 40 51 52 55 56 58 59 60 61 62 63 64 65 1 2 3 4 6 7 8 9 10 11 GPIO_16 RESETn GPIO_22 GPIO_23 GPIO_24 GPIO_25 GPIO_26 GPIO_27 GPIO_39 GPIO_40 GPIO_41 GPIO_42 GPIO_43 GPIO_44 GPIO_45 GPIO_46 GPIO_47 GPIO_48 GPIO_49 GPIO_0 GPIO_1 GPIO_2 GPIO_3 GPIO_4 GPIO_5 GPIO_6 GPIO_7 GPIO_8 GPIO_9 Preliminary & Confidential
< Specification may be changed by Murata without notice >
Murata (China) Investment Co., Ltd. 37 GPIO_10 TRSTn: JTAG Test Reset (active low) (optional) I 12 GPIO_10 Preliminary Specification Number: SP-ABR-105-A P. 6/14 4.3 Configuration pins This table shows the pins used as configuration inputs to set parameters following a reset. The definition of these pins changes immediately after reset to their usual function. To set a configuration bit to 0, attach a 100kohm resistor from the pin to ground. No external circuitry is required to set a configuration bit to 1. Configuration Bits Pin name Configuration Function CON[5]
GPIO_16 CON[4]
GPIO_27 Boot Options 00 = boot from UART 01 = reserved 10 = reserved 11 = boot from Flash (default) 5. Range 5.1 Absolute maximum rating (Ta=25, Z=50ohm) Parameter Condition Rating Units Storage Temperature
-40 /+85 Supply Voltage VDD33 Ta=25 3.6 V Note: Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. No damage assuming only one parameter is set at limit at a time with all other parameters are set within operating condition. 5.2 Operating conditions Parameter Operating Temperature Supply Voltage VDD33 Min.
-30 3.0 Max.
+85 3.6 Units V
* Functionality is guaranteed but specifications require derating at extreme temperatures 6. RoHS Compliance This component can meet with RoHS compliance. Preliminary & Confidential
< Specification may be changed by Murata without notice >
Murata (China) Investment Co., Ltd. Preliminary Specification Number: SP-ABR-105-A P. 7/14 7. RF Characteristics for IEEE802.11 Conditions: 25, VDD33= 3.3V Items Tx Power Level 802.11b (11Mbps) 802.11g (54Mbps) 802.11n (HT20) Min.
Rx Minimum Input Level Sensitivity Min. 802.11b (11Mbps) 802.11g (54Mbps) 802.11n (HT20)
Contents Power Levels Typ.
Typ.
Max. 20.97 23.48 22.17 Max.
-76
-65
-64 Units dBm dBm dBm Units dBm dBm dBm
*Test performed through Murata RF switch connector P/N: MM8030-2610. 8. Power Up Sequence 9. Electrical Characteristics 9.1 I/O Static Ratings, 3.3V Symbol Parameter Condition VIL VIH VHYS IOL@0.4V IOH@VDDIO-0.5V Input capacitance Input low voltage Input high voltage Input hysteresis
Input leakage 1
VDD33 is ON, 0<V(PAD)<VDD33 Min.
-0.4 VDD33*70%
150 4 3
Typ. Max. Units
VDD33*30%
VDD33+0.4
5 5 V V mV mA mA pF A Preliminary & Confidential
< Specification may be changed by Murata without notice >
Murata (China) Investment Co., Ltd. Preliminary Specification Number: SP-ABR-105-A P. 8/14 9.2 Clock Specifications (optional) 9.2.1 RC32K Specifications Parameter Frequency before calibration Startup time Condition
After-calibration frequency accuracy Use 32.768kHz crystal as reference clock Temperature tolerance Duty cycle
9.2.2 Crystal Specifications (32.768kHz) Parameter Condition Crystal frequency Frequency accuracy tolerance Startup time Duty cycle tolerance Crystal load capacitance Crystal shunt capacitance Equivalent Series Resistance (ESR)
Min. 18.6
Typ. 31.8 0.9 Max. 39.8
Units kHz ms 32.3 32.7 33.1 kHz
40 65 50
60 ppm/C
Min.
-40
Typ. Max. 32.768
50 12.5
40 600
7 100 Units kHz ppm ms
pF pF k 10. Reference Circuit Preliminary & Confidential
< Specification may be changed by Murata without notice >
Murata (China) Investment Co., Ltd. Preliminary Specification Number: SP-ABR-105-A P. 9/14 11. OEM Guidance OEM can only use the embedded PCB antenna to guarantee regulatory compliance. Besides that, the following guides must be followed in order to get the best antenna performance.
(1) Place the antenna area on the corner or edge of the main board.
(2) No ground, circuit, component under the antenna area, including the reverse side of PCB. No ground area is as large as possible.
(3) Metal component should be at least 10mm away from PCB antenna.
(4) Plastic case should be at least 10mm away from PCB antenna. If its metal case, its recommended to use external antenna. Preliminary & Confidential
< Specification may be changed by Murata without notice >
Murata (China) Investment Co., Ltd. Preliminary Specification Number: SP-ABR-105-A P. 10/14 12. Package This module product is packaged in tray. 1 tray: 45pcs products 1 inner box: 6 trays with products 1 outer box: 4 inner boxes MOQ: 1080pcs Inner box Outter box Preliminary & Confidential
< Specification may be changed by Murata without notice >
Murata (China) Investment Co., Ltd. Preliminary Specification Number: SP-ABR-105-A P. 11/14 NOTICE 1. Storage Conditions Please use this product within 6month after receipt.
- The product shall be stored without opening the packing under the ambient temperature from 5 to 35 C and humidity from 20 ~ 70 %RH.
(Packing materials, in particular, may be deformed at the temperature over 40 C)
- The product left more than 6months after reception, it needs to be confirmed the solderability before used.
- The product shall be stored in non corrosive gas (Cl2, NH3, SO2, Nox, etc.).
- Any excess mechanical shock including, but not limited to, sticking the packing materials by sharp object and dropping the product, shall not be applied in order not to damage the packing materials. This product is applicable to MSL3 (Based on IPC/JEDEC J-STD-020)
- After the packing opened, the product shall be stored at <30 C / <60 %RH and the product shall be used within 168 hours.
- When the color of the indicator in the packing changed, the product shall be baked before soldering. Baking condition: 125 +5/-0 C, 24 hours, 1 time The products shall be baked on the heat-resistant tray because the material is not heat-resistant. 2. Handling Conditions :
Be careful in handling or transporting products because excessive stress or mechanical shock may break products. Handle with care if products may have cracks or damages on their terminals, the characteristics of products may change. Do not touch products with bear hands that may result in poor solderability. 3. Standard PCB Design (Land Pattern and Dimensions) :
All the ground terminals should be connected to the ground patterns. Furthermore, the ground pattern should be provided between IN and OUT terminals. Please refer to the specifications for the standard land dimensions. The recommended land pattern and dimensions is as Murata's standard. The characteristics of products may vary depending on the pattern drawing method, grounding method, land dimensions, land forming method of the NC terminals and the PCB material and thickness. Therefore, be sure to verify the characteristics in the actual set. When using non-standard lands, contact Murata beforehand. 4. Notice for Chip Placer :
When placing products on the PCB, products may be stressed and broken by uneven forces from a worn-out chucking locating claw or a suction nozzle. To prevent products from damages, be sure to follow the specifications for the maintenance of the chip placer being used. For the positioning of products on the PCB, be aware that mechanical chucking may damage products. 5. Soldering Conditions The recommendation conditions of soldering are as in the following figure. Preliminary & Confidential
< Specification may be changed by Murata without notice >
Murata (China) Investment Co., Ltd. Preliminary Specification Number: SP-ABR-105-A P. 12/14 When products are immersed in solvent after mounting, pay special attention to maintain the temperature difference within 100 C. Soldering must be carried out by the above mentioned conditions to prevent products from damage. Set up the highest temperature of reflow within 260 C. Contact Murata before use if concerning other soldering conditions. Reflow soldering standard conditions (Example) Within 3 s Cooling down Slowly 240 ~ 250 C 220 C 180 C 150 C Pre-heating Within 120 s time(s) Please use the reflow within 2 times. Use rosin type flux or weakly active flux with a chlorine content of 0.2 wt % or less. Within 60 s 6. Cleaning :
Since this Product is Moisture Sensitive, any cleaning is not permitted. 7. Operational Environment Conditions :
Products are designed to work for electronic products under normal environmental conditions
(ambient temperature, humidity and pressure). Therefore, products have no problems to be used under the similar conditions to the above-mentioned. However, if products are used under the following circumstances, it may damage products and leakage of electricity and abnormal temperature may occur.
- In an atmosphere containing corrosive gas ( Cl2, NH3, SOx, NOx, etc.).
- In an atmosphere containing combustible and volatile gases.
- Dusty place.
- Direct sunlight place.
- Water splashing place.
- Humid place where water condenses.
- Freezing place. If there are possibilities for products to be used under the preceding clause, consult with Murata before actual use. As it might be a cause of degradation or destruction to apply static electricity to products, do not apply static electricity or excessive voltage while assembling and measuring. 8. Input Power Capacity :
Products shall be used in the input power capacity as specified in this specifications. Inform Murata beforehand, in case that the components are used beyond such input power capacity range. This module is not approved for use when being powered by AC power lines, either directly or Preliminary & Confidential
< Specification may be changed by Murata without notice >
Murata (China) Investment Co., Ltd. indirectly through another device. 9. Limitation of Applications:
Preliminary Specification Number: SP-ABR-105-A P. 13/14 Please contact Murata before using products for the applications listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party's life, body or property.
- Aircraft equipment.
- Aerospace equipment.
- Undersea equipment.
- Medical equipment.
- Transportation equipment (vehicles, trains, ships, etc.).
- Traffic signal equipment.
- Disaster prevention / crime prevention equipment.
- Data-processing equipment
- Application of similar complexity and/ or reliability requirements to the applications listed in the above. Preliminary & Confidential
< Specification may be changed by Murata without notice >
Murata (China) Investment Co., Ltd. Preliminary Specification Number: SP-ABR-105-
A P. 14/15 CAUTION PLEASE READ THIS NOTICE BEFORE USING OUR PRODUCTS. Please make sure that your product has been evaluated and confirmed from the aspect of the fitness for the specifications of our product when our product is mounted to your product. All the items and parameters in this product specification/datasheet/catalog have been prescribed on the premise that our product is used for the purpose, under the condition and in the environment specified in this specification. You are requested not to use our product deviating from the condition and the environment specified in this specification. Please note that the only warranty that we provide regarding the products is its conformance to the specifications provided herein. Accordingly, we shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those specified in this specification. WE HEREBY DISCLAIMS ALL OTHER WARRANTIES REGARDING THE PRODUCTS, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, THAT THEY ARE DEFECT-FREE, OR AGAINST INFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. The product shall not be used in any application listed below which requires especially high reliability for the prevention of such defect as may directly cause damage to the third party's life, body or property. You acknowledge and agree that, if you use our products in such applications, we will not be responsible for any failure to meet such requirements. Furthermore, YOU AGREE TO INDEMNIFY AND DEFEND US AND OUR AFFILIATES AGAINST ALL CLAIMS, DAMAGES, COSTS, AND EXPENSES THAT MAY BE INCURRED, INCLUDING WITHOUT LIMITATION, ATTORNEY FEES AND COSTS, DUE TO THE USE OF OUR PRODUCTS IN SUCH APPLICATIONS.
- Aircraft equipment.
- Aerospace equipment
- Undersea equipment.
- Power plant control equipment
- Medical equipment.
- Transportation equipment (vehicles, trains, ships, elevator, etc.).
- Traffic signal equipment.
- Disaster prevention / crime prevention equipment.
- Burning / explosion control equipment
- Application of similar complexity and/ or reliability requirements to the applications listed in the above. We expressly prohibit you from analyzing, breaking, Reverse-Engineering, remodeling altering, and reproducing our product. Our product cannot be used for the product which is prohibited from being manufactured, used, and sold by the regulations and laws in the world. We do not warrant or represent that any license, either express or implied, is granted under any our patent right, copyright, mask work right, or our other intellectual property right relating to any combination, machine, or process in which our products or services are used. Information provided by us regarding third-party products or services does not constitute a license from us to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from us under our patents or other intellectual property. Please do not use our products, our technical information and other data provided by us for the purpose of developing of mass-destruction weapons and the purpose of military use. Moreover, you must comply with "foreign exchange and foreign trade law", the "U.S. export administration regulations", etc. Please note that we may discontinue the manufacture of our products, due to reasons such as end of supply of materials and/or components from our suppliers. Customer acknowledges that Murata will, if requested by you, conduct a failure analysis for defect or alleged defect of Products only at the level required for consumer grade Products, and thus such analysis may not always be available or be in accordance with your request (for example, in cases where the defect was caused by components in Products supplied to Murata from a third party). By signing on specification sheet or approval sheet, you acknowledge that you are the legal representative for your company and that you understand and accept the validity of the contents herein. When you are not able to return the signed version of specification sheet or approval sheet within 90 days from receiving date of specification sheet or approval sheet, it shall be deemed to be your consent Preliminary & Confidential
< Specification may be changed by Murata without notice >
Murata (China) Investment Co., Ltd. on the content of specification sheet or approval sheet. Preliminary Specification Number: SP-ABR-105-A P. 15/15 Customer acknowledges that engineering samples may deviate from specifications and may contain defects due to their development status. We reject any liability or product warranty for engineering samples. In particular we disclaim liability for damages caused by the use of the engineering sample other than for evaluation purposes, particularly the installation or integration in the product to be sold by you, deviation or lapse in function of engineering sample, improper use of engineering samples. We disclaim any liability for consequential and incidental damages. If you cant agree the above contents, you should inquire our sales. Preliminary & Confidential
< Specification may be changed by Murata without notice >
Murata (China) Investment Co., Ltd. OEM Guidance 1. Applicable FCC rules This module is granted by Single Modular Approval. It complies to the requirements of FCC part 15C, section 15.247 rules. 2. The specific operational use conditions This module can be used in IoT devices. The input voltage to the module is nominally 3.3VDC. The operational ambient temperature of the module is -30 to 85 degree C. Only the embedded PCB antenna is allowed. Any other external antenna is prohibited. 3. Limited module procedures N/A 4. Trace antenna design N/A 5. RF exposure considerations The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. If the equipment built into a host as a portable usage, the additional RF exposure evaluation may be required as specified by 2.1093. 6. Antenna Antenna type: PCB antenna; Peak gain: -0.1dBi 7. Label and compliance information An exterior label on OEMs end product can use wording such as the following:
Contains Transmitter Module FCC ID: VPYCMWC1ZZABR or Contains FCC ID: VPYCMWC1ZZABR. 8. Information on test modes and additional testing requirements a)The modular transmitter has been fully tested by the module grantee on the required number of channels,modulation types, and modes, it should not be necessary for the host installer to re-test all the available transmitter modes or settings. It is recommended that the host product manufacturer, installing the modular transmitter,perform some investigative measurements to confirm that the resulting composite system does not exceed the spurious emissions limits or band edge limits (e.g., where a different antenna may be causing additional emissions). b)The testing should check for emissions that may occur due to the intermixing of emissions with the other transmitters, digital circuitry, or due to physical properties of the host product
(enclosure). This investigation is especially important when integrating multiple modular transmitters where the certification is based on testing each of them in a stand-alone configuration. It is important to note that host product manufacturers should not assume that because the modular transmitter is certified that they do not have any responsibility for final product compliance. c)If the investigation indicates a compliance concern the host product manufacturer is obligated to mitigate the issue. Host products using a modular transmitter are subject to all the applicable individual technical rules as well as to the general conditions of operation in Sections 15.5, 15.15, and 15.29 to not cause interference. The operator of the host product will be obligated to stop operating the device until the interference have been corrected . 9. Additional testing, Part 15 Sub part B disclaimer The final host / module combination need to be evaluated against the FCC Part 15B criteria for unintentional radiators in order to be properly authorized for operation as a Part 15 digital device. The host integrator installing this module into their product must ensure that the final composite product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation and should refer to guidance in KDB 996369. For host products with certified modular transmitter, the frequency range of investigation of the composite system is specified by rule in Sections 15.33(a)(1) through
(a)(3), or the range applicable to the digital device, as shown in Section 15.33(b)(1), whichever is the higher frequency range of investigation When testing the host product, all the transmitters must be operating.The transmitters can be enabled by using publicly-
available drivers and turned on, so the transmitters are active. In certain conditions it might be appropriate to use a technology-specific call box (test set) where accessory 50 devices or drivers are not available. When testing for emissions from the unintentional radiator, the transmitter shall be placed in the receive mode or idle mode, if possible. If receive mode only is not possible then, the radio shall be passive (preferred) and/or active scanning. In these cases, this would need to enable activity on the communication BUS (i.e., PCIe, SDIO, USB) to ensure the unintentional radiator circuitry is enabled. Testing laboratories may need to add attenuation or filters depending on the signal strength of any active beacons (if applicable) from the enabled radio(s). See ANSI C63.4, ANSI C63.10 and ANSI C63.26 for further general testing details. The product under test is set into a link/association with a partnering device, as per the normal intended use of the product. To ease testing, the product under test is set to transmit at a high duty cycle, such as by sending a file or streaming some media content. FCC Warning:
Any Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. ISED RF exposure statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Le rayonnement de la classe b repecte ISED fixaient un environnement non contrls.Installation et mise en uvre de ce matriel devrait avec changeur distance minimale entre 20 cm ton corps.Lanceurs ou ne peuvent pas coexister cette antenne ou capteurs avec dautres. IC Label Instructions:
The outside of final products that contains this module device must display a label referring to the enclosed module. This exterior label can use wording such as:
Contains Transmitter Module IC: 772C-CMWC1ZZABR,or Contains IC: 772C-CMWC1ZZABR, Any similar wording that expresses the same meaning may be used. Instructions d'tiquetage IC:
L'extrieur des produits finis contenant ce module doit afficher une tiquette faisant rfrence au module inclus. Cette tiquette extrieure peut utiliser des libells tels que: contient le module metteur IC: 772C-CMWC1ZZABR ou contient: IC: 772C-CMWC1ZZABR , tout libell similaire exprimant le mme sens peut tre utilis.