Specification Number : SP-xxxx P.1/18 ZigBee Module Data Sheet Sample Part Number: CMBA1ZZABE For 802.15.4 SMD Type Module Specification Number : SP-xxxx P.2/18 Revision History Date Description Comments Revision Code 0.1 May.14,2013 Initial Draft TYPE-ABE_Prelimi nary_20150323 0.2 May.07,2015
-Modify Maximum transmitting power from 8dBm
-Modify size description, add tolerance information 0.3 July.10,2015 0.4 July.22, 2015 0.5 Aug.26, 2015 0.6 Nov.11, 2015 to 5dBm
-Modify Operating Voltage from 2V~3.6V to 2.7V~3.6V
-Add information of packing condition and storage condition
-Add current consumption in Electrical Characteristics
-Modify size information of Customer Board Design recommendation
-Modify pin function of pin17 & pin 18, remove UART function of these two pins
-Add pin description of CC2530 which used to 1.0 Dec.09, 2015 control internal flash 1.1 July.28,2016 1.2 Sept. 7, 2017
-Add NC pin description of CC2530
-Add Label information
-Add pictures in Packing condition
-Add regulatory statements.
-Revise label info by adding regulatory identifiers. Specification Number : SP-xxxx P.3/18 TABLE OF CONTENTS 1. Scope 4 2. Part Number 4 3. Dimensions, Marking and Terminal Configurations 5 4. Maximum absolute ratings 10 5. Operating Condition 10 6. Electrical Characteristics 10 7. Power Sequences 11 8.1 Power Up/Down Sequence 11 8.2 Reset and Power Cycle Sequence 11 8. Packing Condition 12 NOTICE 13 Specification Number : SP-xxxx P.4/18 1. Scope This specification is applied to the IEEE802.15.4 ZigBee Module
- Interface
: UART, SPI, PWM
- IC
: CC2530 (Texas Instruments)
- Reference Clock: 32MHz reference clock is integrated.
- RoHS
: This module is compliant with the RoHS directive. 2. Part Number Part Number CMBA1ZZABE Specification Number : SP-xxxx P.5/18 3. Dimensions, Marking and Terminal Configurations Table 1 Dimension (Unit: mm) Mark Dimension Mark Dimension Mark Dimension L a1 b2 b5 b8 b11 c2 25.00.2 0.80.1 0.40.1 7.00.1 2.20.1 2.20.1 1.00.1 W a2 b3 b6 b9 b12 e1 17.40.2 0.80.1 1.00.1 0.250.15 2.60.1 3.150.1 0.60.1 T b1 b4 b7 b10 c1 e2 3.1 max 1.60.15 6.00.1 3.150.1 2.60.1 1.00.1 1.40.1 Note: This module cannot connect to the external antenna. It has to use the existing antenna (PCB Antenna). Specification Number : SP-xxxx P.6/18 Label Information RQ code: for internal use Model name FCC ID IC ID Inspection number Specification Number : SP-xxxx P.7/18 Terminal Configurations
< Top View >
Table 2 Terminal Configurations Connection to Pin NO. Terminal Name Type IC terminal Description 1 2 3 4 5 6 7 8 9 GND GND GND GND P2_4 P2_3 P2_2/DC P2_1/DD P1_7/UART_RX 10 P1_6/UART_TX Ground Ground Ground Ground I/O I/O I/O I/O I/O I/O
-
-
-
-
P2_4 P2_3 P2_2 P2_1 P1_7 P1_6 Ground Ground Ground Ground Port 2_4/32.768kHz XOSC Q1 Port 2_3/32.768kHz XOSC Q2 Port 2_2 or Debug clock Port 2_1 or Debug data Port 1_7 or UART RX Port 1_6 or UART TX Specification Number : SP-xxxx P.8/18 11 12 GND VDD 13 P1_0 14 15 16 17 18 19 20 21 22 23 24 P0_6/PWM P0_5/PWM P0_4/PWM P0_3/PWM P0_2/PWM P0_1 P0_0 RST_N GND NC GND 25~ 38 GND Ground
-
Ground Power AVDD/DVDD Power supply I/O I/O I/O I/O I/O I/O I/O I/O I P1_0 P0_6 P0_5 P0_4 P0_3 P0_2 P0_1 P0_0 Port 1_0 20mA drive capability Port 0_6 or PWM Port 0_5 or PWM Port 0_4 or PWM Port 0_3 or PWM Port 0_2 or PWM Port 0_1 Port 0_0 RESET_N Reset, active-low Ground
-
Ground Ground
-
-
-
-
Ground NC Ground Ground Note: GPIO pins are to be left OPEN if not used. Table 2.1 Internal SPI configuration and NC pin IC Pin NO. Terminal Name Type Description 5 6 7 8 9 12 36 P1_5/SPI_MOSI P1_4/SPI_MISO P1_3/SPI_CLK P1_2/SPI_SS P1_1 P0_7 P2_0 I/O I/O I/O I/O I/O I/O I/O Used to control internal flash Used to control internal flash Used to control internal flash Used to control internal flash Float in module Float in module Float in module Specification Number : SP-xxxx P.9/18
(Reference)
<Customer Board Design recommendation for good RF performance Top View>
Specification Number : SP-xxxx P.10/18 4. Maximum absolute ratings Table 3 Maximum ratings Item Storage Temperature VCC Voltage on any Digital Pin Input RF Level Min
-40
-0.1
-0.1 Max
+85 3.7 VCC+0.1 Unit degC V V 10 dBm 5. Operating Condition Table 4 Operating specification Item Operating Temperature VCC Min
-40 2.7 Typ Max
+85 25 3.3 3.6 Unit degC V 6. Electrical Characteristics Table 5 Electrical specification parameters Remarks Remarks
(Condition: T= +25deg.C, VCC=3.3V and fc=2440MHz, measured at antenna feed point.) Items Specification Mode Contents IEEE 802.15.4 offset QPSK Channel frequency (spacing) 2405 to 2480 MHz (5MHz) Radio baud rate Frequency tolerance 250kbps
-40
-
40 Transmitter Min. Typ. Max. ppm unit Output power 0 2.5 5 dBm Spectral density mask (Relative)
< fc-3.5MHz, RBW:100kHz
> fc+3.5MHz, RBW:100kHz
-
-
Spectral density mask (Absolute)
< fc-3.5MHz, RBW:100kHz
> fc+3.5MHz, RBW:100kHz 1000 chips, RMS
-
-
-
EVM
-47
-44
-59
-55
-20
-20
-30
-30 dBr dBm 10 35
%
Receiver Min. Typ. Max. unit Receiver sensitivity (PER < 1%)
-
-95
-85 dBm Current Consumption Min. Typ. Max. unit Continuous Tx(1) Continuous Rx(1)
-
-
32 25 mA mA Note(1): Under condition of transmitting or receiving continuous wave Specification Number : SP-xxxx P.11/18 7. Power Sequences 8.1 Power Up/Down Sequence 8.2 Reset and Power Cycle Sequence Symbol Description Ta Tb Tc Td Te Time between VCC valid and RST_N ramped-up Time between VCC valid and GPIO enabled Time between RST_N invalid and VCC invalid Time between GPIO invalid and VCC invalid Length of RST_N pulse Typ. Ta > 0 Tb > 400 Tc > 0 Td > 0 Te > 1 Unit usec VCCRST_NGPIOTaTbTcTdHLHLHLPower UpPower DownVCCRST_NTeHHL Specification Number : SP-xxxx P.12/18 8. Packing Condition There are 50pcs of products per tray. One inner box has nice trays including one tray without products for top. Products quantity of one inner box is 400pcs. One outer box has four inner boxes. Products quantity of one outer box is 1600pcs. Specification Number : SP-xxxx P.13/18 NOTICE 1 Storage Conditions:
Please use this product within 6 months after receipt. The product shall be stored without opening the packing under the ambient temperature from 5 to 35 C and humidity from 20 to 70 %RH. (Packing materials, in particular, may be deformed at the temperature over 40 C) The product shall be stored in non-corrosive gas (Cl2, NH3, SO2, NOx, etc.). Any excess mechanical shock including, but not limited to, sticking the packing materials by sharp object and dropping the product, shall not be applied in order not to damage the packing materials. This product is applicable to MSL3 (Based on JEDEC Standard J-STD-020) After the packing opened, the product shall be stored at <30deg.C / <60%RH and the product shall be used within 168hours. When the color of the indicator in the packing changed, the product shall be baked before soldering. Baking condition : 125 +5/-0deg.C, 24hours, 1time The products shall be baked on the heat-resistant tray because the material (Base Tape, Reel Tape and Cover Tape) are not heat-resistant. 2 Handling Conditions :
Be careful in handling or transporting products because excessive stress or mechanical shock may break products. Handle with care if products may have cracks or damages on their terminals, the characteristics of products may change. Do not touch products with bear hands that may result in poor solderability and destroy by static electrical charge. Specification Number : SP-xxxx P.14/18 3 Standard PCB Design (Land Pattern and Dimensions) :
All the ground terminals should be connected to the ground patterns. Furthermore, the ground pattern should be provided between IN and OUT terminals. Please refer to the specifications for the standard land dimensions. The recommended land pattern and dimensions is as Murata's standard. The characteristics of products may vary depending on the pattern drawing method, grounding method, land dimensions, land forming method of the NC terminals and the PCB material and thickness. Therefore, be sure to verify the characteristics in the actual set. When using non-standard lands, contact Murata beforehand. 4 Notice for Chip Placer :
When placing products on the PCB, products may be stressed and broken by uneven forces from a worn-out chucking locating claw or a suction nozzle. To prevent products from damages, be sure to follow the specifications for the maintenance of the chip placer being used. For the positioning of products on the PCB, be aware that mechanical chucking may damage products. Specification Number : SP-xxxx P.15/18 5 Soldering Conditions :
The recommendation conditions of soldering are as in the following figure. When products are immersed in solvent after mounting, pay special attention to maintain the temperature difference within 100 C. Soldering must be carried out by the above mentioned conditions to prevent products from damage. Set up the highest temperature of reflow within 260 . Contact Murata before use if concerning other soldering conditions. 180 deg.C 220 deg.C 240 to 250 deg.C 150 deg.C Reflow soldering standard conditions(Example) Within 3s Cooling down Slowly Pre-heating Within 120s Within 60s time(s) Please use the reflow within 2 times. Use rosin type flux or weakly active flux with a chlorine content of 0.2 wt % or less. 6 Cleaning:
Since this Product is Moisture Sensitive, any cleaning is not permitted. Specification Number : SP-xxxx P.16/18 7 Operational Environment Conditions:
Products are designed to work for electronic products under normal environmental conditions
(ambient temperature, humidity and pressure). Therefore, products have no problems to be used under the similar conditions to the above-mentioned. However, if products are used under the following circumstances, it may damage products and leakage of electricity and abnormal temperature may occur.
- In an atmosphere containing corrosive gas ( Cl2, NH3, SOx, NOx etc.).
- In an atmosphere containing combustible and volatile gases.
- Dusty place.
- Direct sunlight place.
- Water splashing place.
- Humid place where water condenses.
- Freezing place. If there are possibilities for products to be used under the preceding clause, consult with Murata before actual use. As it might be a cause of degradation or destruction to apply static electricity to products, do not apply static electricity or excessive voltage while assembling and measuring. 8 Input Power Capacity:
Products shall be used in the input power capacity as specified in this specifications. Inform Murata beforehand, in case that the components are used beyond such input power capacity range. 9 FCC/Industry Canada Statement (to be placed on End Products) FCC statement:
This module has been tested and found to comply with the FCC Part15. These limits are designed to provide reasonable protection against harmful interference in approved installations. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may Specification Number : SP-xxxx P.17/18 cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Modifications or changes to this equipment not expressly approved by Murata Manufacturing Co., Ltd. may void the users authority to operate this equipment. The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number
(A) If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: VPYCMABE or Contains FCC ID: VPYCMABE.
(B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains FCC certified transmitter module(s). To satisfy FCC RF Exposure requirements for mobile and base station transmission devices, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during operation. To ensure compliance, operation at closer than this distance is not recommended. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IC statement:
Label of the end product:
The final end product must be labeled in a visible area with the following "Contains transmitter module Specification Number : SP-xxxx P.18/18 IC: 772C-CMABE"
This Class B digital apparatus complies with Canadian ICES-003. Cetappareilnumrique de la classe B estconforme la norme NMB-003 du Canada. This device complies with Industry Canadas license-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1) lappareil ne doit pas produire de brouillage;
2) lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body. Dclaration d'exposition aux radiations:
Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20cm de distance entre la source de rayonnement et votre corps. Notice to OEM integrator The end user manual shall include all required regulatory information/warning as show in this manual. The OEM integrator is responsible for testing their endproduct for any additional compliance requirements required with this module installed. If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. The end product shall haves the words Contains Transmitter Module FCC ID: VPYCMABE, IC: 772C-CMABE.