Quick Start Guide NC-6602 Wireless Active Noise-Canceling Headphones with Bluetooth* Connectivity Controls
(2)
(3)
(4)
(1)
(7) (6)(5)
(8)
(1) ANC ON/OFF button switches the ANC (Active Noise
(2) FORWARD/VOLUME button can be used to increase volume (short press), skip to the next song (long press), or begin/end a phone call on a Bluetooth-
connected mobile phone.
(3) POWER/PLAY/PAUSE button switches the pauses audio playback (short press). Secondary call functions include Answer Call (press) and End Call/
Reject Call (long press).
(4) BACK/VOLUME button can be used to decrease volume (short press) or skip to the previous song
(long press). A54-00002-37754
(5) MICROPHONE can be used for talkback during phone calls.
(7)
(6) AUX IN stereo jack can be used to listen to audio from external devices as normal wired headphones using audio cables with 3.5 mm stereo connectors. INDICATOR LED shows the charging status
(red = charging; blue = fully charged) as well as the Bluetooth status (blinking blue and red = in pairing mode; blue = connected; blinking blue = audio playback underway).
(8) MICRO USB jack is for charging rechargeable batteries. Getting started Power Supply The unit is powered by a built-in, lithium-polymer rechargeable battery. Charge the built-in battery for at least four hours before 1. Long press the POWER/PLAY/PAUSE button to turn ON the unit. The INDICATOR LED indicator will light on. 2. Long press the POWER/PLAY/PAUSE button again turn OFF the To charge the internal battery, follow these steps:
1. Connect the smaller end of the supplied USB cable to the MICRO USB jack. 2. Connect the other end to a powered USB jack on your computer or an AC power supply (not included). 3. The INDICATOR LED indicator will change color to red during charging. 4. When fully charged, the INDICATOR LED indicator will turn blue. Low Battery Warning When the battery voltage drops below 3.0 V, there will be a warning beep every 60 seconds. voltage drops lower then 2.9 V. Warnings:
Adjusting volume Short press the FORWARD/VOLUME and BACK/VOLUME buttons to increase or reduce the headphone volume. When the volume reaches maximum, there is a warning tone. t 1. Adjust the headband and arm of the headphones, exposing 2 3 cm. 2. Place the headphones over your ears and head with the headband in the middle. 3. Tight the headband and arm until the ear cups cover your ears While using the built-in battery, the environmental temperature should be 5 C (41 F) to 35 C (95 F). To get the longest service life for the built-in battery, charge at ANC (Active Noise Cancellation) The ANC (Active Noise Cancellation) function is available in both wired and wireless conditions. The ANC circuit must be switched room temperature. Attention should be drawn the environmental aspects of battery disposal. Battery shall not be exposed to excessive heat such as sunshine, To switch on the ANC circuit, press and hold the ANC button for 1 second. The INDICATOR LED will light green. to work. In order to prolong the battery service life, please charge every 6 months. Immediately charge the battery if the headphones are left unused for a lengthy period. The battery is original to the headphones. Please do not attempt to change the battery by yourself. Bluetooth pairing 1. To switch on Bluetooth, press and hold the POWER/PLAY/
PAUSE button for about 3 seconds. The INDICATOR LED indicator will blink blue and red alternately to indicate the unit is in pairing mode. 2. On the Bluetooth device, enable Bluetooth and select NC-6602 from the Device List. (Refer to the user manual of your Bluetooth device for detailed operations.) 3. If the Bluetooth device prompts for a passcode, use 0000. 4. When pairing is successful, the INDICATOR LED will light a steady blue. 5. When done, stop playback on the external device and disconnect the audio cable from the AUX IN jack on the headphones. PAUSE button for about 3 seconds. the connection. If the headphones have previously been paired with a Bluetooth device, the headphones will automatically connect with that device if the device is powered on and within range. If not, the headphones will enter standby mode, and the INDICATOR LED will light a steady blue. NOTE: If you want to connect your headphones to another Bluetooth audio device, you need to disconnect the current device Using a Bluetooth device 1. When successfully paired, sound from your Bluetooth device will be audible through the headphones 2. Press the POWER/PLAY/PAUSE button to pause playback. Press again to resume playback. 3. Short press the FORWARD/BACK buttons to adjust the headphone volume. You can also adjust the volume directly on your paired Bluetooth device. 4. Long press the FORWARD/BACK buttons to select your desired NOTE: the BLUETOOTH LED indicator will blink blue during playback. Using the AUX IN jack 1. Insert one end of the audio cable into the LINE OUT or headphone jack on your external audio device. Receiving a phone call These headphones are equipped with a built-in microphone, which allows you to make calls on a Bluetooth-enabled mobile phone. Make sure your Bluetooth-enabled mobile phone is paired with the headphones. When a call comes in to the connected mobile phone, you will hear an incoming call alert on the headphones. Your headphones and mobile phone should be within 10 m (33 ft) of each other. 1. Short press the POWER/PLAY/PAUSE button to answer the incoming call. 2. Long press the POWER/PLAY/PAUSE button to reject the call. 3. Short press the POWER/PLAY/PAUSE button again to end the call. To prevent possible hearing damage, do not listen at high volume for long periods. Troubleshooting No power The Bluetooth device cannot pair or connect with the headphones. Power is not on; Long press to turn ON the unit. Make sure the battery is charged. You have not activated the Bluetooth function on your device. Refer to your devices user manual to activate the Bluetooth function. The unit is already paired with another Bluetooth device; disconnect that device and then try again. 2. Connect the other end of the cable to the AUX IN 3.5 mm stereo jack on the headphones. CAUTION:
NOTE: If the headphones are in ON mode, the headphones will work as normal, wired headphones. 3. Begin playback on the external device. The external devices sound output will be heard through the headphones. to avoid damage, scratches or bracket deformation when not in use. Please do not bend or twist the bracket to avoid deformation. Please do not tear out the ear cushions or allow to be removed 4. To adjust volume, use the volume control on the external by unauthorized personnel. audio device. Do not use the headphones in dangerous areas or areas where you cannot hear the outside sound. IMPORTANT SAFETY INFORMATION 4. Read these instructions. 5. Keep these instructions. 6. Heed all warnings. 7. Follow all instructions. 8. Do not use this apparatus near water. 9. Clean only with dry cloth. 11. Do not expose this product to bright sunshine for a long time. 12. Do not disassemble or modify this product. 13. Please store this product in a clean and dry environment. 14. WARNING! To prevent possible hearing damage, do not listen at high volume levels for long periods. cation Driver unit Impedance Driver frequency range Headset sensitivity Mic sensitivity ANC (Active Noise Cancellation) Rechargeable battery Battery type Charge method Charging power Operating time Charging time Standby time Bluetooth Version Operating frequency RF output power Working distance 40 mm 32
20 Hz to 20 kHz 97 dB (3 dB)
-42 dB Up to 20 25 dB @ 100 Hz to 1000 kHz 3.7 V 300 mAh lithium-polymer battery Computer USB interface DC 5 V 300 mA Up to 6 hours 2+ hours Up to 200 hours Version 5.0 2.4 to 2.48 GHz 0 dBm Up to 10 m measured in open space (wall and structures FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION SUPPLIERS DECLARATION OF CONFORMITY (SDoC) Responsible Party Name:
Address:
Phone Number:
FCC ID:
Music Tribe Commercial NV Inc. 5270 Procyon Street Las Vegas, NV 89118 USA
+1 702 800 8290 10-PHTM-HWQ Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject NC-6602 This equipment has been tested and found to comply with the limits for a ClassB digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by the interference by one or more of the following measures:
including interference that may cause undesired operation. for compliance could void the user's authority to operate the equipment. Caution!
The Music Tribe is not responsible for any radio or TV interference caused equipment FCC RF Radiation Exposure Statement. FCC RF Radiation Exposure Statement:
(1) This Transmitter must not be co-located or operating in conjuction with any other antenna or transmitter.
(2) This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. LEGAL DISCLAIMER description, thout notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Auratone and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. Music Tribe Global Brands Ltd. 2019 All rights reserved. LIMITED WARRANTY For the applicable warranty terms and conditions and additional information regarding Music Tribes Limited Warranty, please see complete details online at musictribe.com/warranty.